®
WIRELESS FREEDOM FOR YOUR PROJECTOR.
LiteShow
USER’S GUIDE
Declaration of Conformity
Manufacturer: InFocus Corporation, 27700B SW Parkway Ave. Wilsonville, Oregon 97070 USA
European Office: Strawinskylaan 585, 1077 XX Amsterdam, The Netherlands
We declare under our sole responsibility that the LiteShow wireless projection adapter conforms to the following
directives and norms:
EMC Directive 89/336/EEC, Amended by 93/68/EEC
EMC: EN 55022
EN 55024
EN 61000-3-2
EN 61000-3-3
Low Voltage Directive 73/23/EEC, Amended by 93/68/EEC
Safety: EN 60950: 2000
The Agency/Regulatory Approval for the computer’s wireless adapter is solely the responsibility of the adapter
manufacturer - not InFocus Corporation.
May, 2003
Trademarks
Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple Computer, Inc. IBM and PS/2 are
trademarks or registered trademarks of International Business Machines, Inc. Microsoft, PowerPoint, and Windows are
trademarks or registered trademarks of Microsoft Corporation. InFocus, LiteShow, and LP are trademarks or registered
trademarks of InFocus Corporation.
User’s Guide Travel Restrictions
You must keep this User’s Guide with your LiteShow adapter at all times when travelling in countries other than the
United States of America.
FCC Warning
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own
expense. The Agency/Regulatory Approval for the computer’s wireless adapter is solely the responsibility of the adapter
manufacturer - not InFocus Corporation.
Canada
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
EN 55022 Warning
This is a Class A product. In a domestic environment it may cause radio interference, in which case the user may be required to take
adequate measures.
Radio Frequency/Channel Restriction Information
Agency Approvals
UL, c-UL, TÜV, NOM, IRAM, GOST, C-Tick
Contents
Introduction
1
What is LiteShow?
Contents
About the documentation
If you need assistance
2
4
5
5
Projecting via LiteShow
7
About the LiteShow Adapter
The LiteShow Splash Screen
The LiteShow Manager
Settings Window
7
9
11
15
Troubleshooting and Frequently Asked Questions
21
Troubleshooting
Frequently Asked Questions
21
22
Glossary
25
27
Appendix
Specifications
Accessories
Compatible projectors
27
28
29
InFocus LiteShow User’s Guide
1
Introduction
®
Congratulations. You have chosen to step into the future of wireless projection through the use of the InFocus
®
LiteShow cable-free digital projection system. LiteShow is a powerful and secure wireless multimedia projection
adapter which allows you to send sharp images from a PC or Macintosh computer to a compatible projector. LiteShow
is easy to set up and configure, and it eliminates the need to carry and connect computer cables.
the LiteShow adapter
If you haven’t yet set LiteShow up, you can go ahead and do so now by following the instructions in the Quick Start
Guide that came with your LiteShow.
2
InFocus LiteShow User’s Guide
Be sure to register your LiteShow online at www.infocus.com/service/register to receive product updates, announce-
ments, and registration incentives.
What is LiteShow?
The sleek LiteShow adapter contains an 802.11b compliant wireless radio that works in tandem with the proprietary
LiteShow Manager software and a wireless LAN adapter or a USB wireless adapter connected to your computer. This
combination gives you presentations that are as sharp the best tethered projector and computer setup.
LiteShow
adapter
computer with a wireless adapter or
USB wireless adapter
and LiteShow Manager software installed
wireless
projection
transmitted data
InFocus LiteShow User’s Guide
LiteShow and the projector
3
The LiteShow adapter connects to a compatible projector by plugging its embedded M1 connector into a projector’s
M1 receptacle. The adapter’s latch mechanism is attached by tightening the two thumbscrews. If the projector’s Auto-
Source option is on, source selection in the projector automatically switches to the standard M1 connector when data
from the LiteShow adapter becomes available.
®
®
Please note that LiteShow is designed for business presentations, such as Microsoft PowerPoint , but not for video or
multimedia displays like a DVD.
LiteShow and the computer
The LiteShow adapter communicates to supported computers via the source computer’s wireless LAN adapter (inte-
grated or PC card) or USB wireless adapter. This communication provides a data path that results in wireless projec-
tion.
Managing LiteShow
The LiteShow Manager interface allows you to project to any LiteShow-enabled projector within range It also lets you
set application preferences and adjust the LiteShow adapter's settings. For example, you can rename the LiteShow
adapter and the LiteShow adapter's network, or specify the LiteShow adapter's IP address.
Security
LiteShow’s encryption technology delivers security similar to that found in computer-to-projector cabled setups.
Capabilities
LiteShow has a line-of-sight range of up to 300 feet (91.44 meters) and a data rate of up to 11Mbps. However, keep in
mind that range and data rate can be lessened by distance, walls or other wireless devices. LiteShow also handles up to
XGA (1024x768) resolution along with 24-bit color depth.
4
InFocus LiteShow User’s Guide
Contents
Your LiteShow system comes with the items shown in the graphic immediately below. Note that the wireless PC card
adapter* is optional. This depends on if you bought the LiteShow system that comes with a wireless adapter or if you
already have an adapter and opted for the package that comes without a wireless adapter.
wireless PC card adapter *
LiteShow adapter
LiteShow carrying case
LiteShow documentation
and CD
* optional depending on which LiteShow offering you purchased
InFocus LiteShow User’s Guide
5
About the documentation
Use the LiteShow Quick Start Guide included in the LiteShow packaging to install and set up and LiteShow. The Lite-
Show User’s Guide contains more information and can be used to fine tune your wireless projection settings to match
your needs or to troubleshoot problems you may run into. You can also use the online-Help file to guide you with
questions while operating the LiteShow Manager.
Both this User’s Guide and the Quick Start Guide are available on the included CD as Adobe Acrobat PDF files.
If you need assistance
The first place to look for help is in this User’s Guide. Be sure to check the guidelines in the Troubleshooting section on
page 21. Or, check the Service and Support section of our website at http://www.infocus.com/service.
If those sources don’t answer your question, call InFocus Customer Service in the United States directly at 1-800-799-
9911. Call between 6 a.m. and 6 p.m. PST, Monday through Friday. Service is available in North America after hours
and on weekends for a fee at 1-888-592-6800.
cus.com.
6
InFocus LiteShow User’s Guide
InFocus LiteShow User’s Guide
7
Projecting via LiteShow
This section gives you more detail on LiteShow and its parts and features. Reading this section should give you a bet-
ter understanding of the LiteShow system and allow you to, if needed, make changes to it.
About the LiteShow Adapter
Before you begin projecting via LiteShow, take a minute to examine the LiteShow adapter and keep the following in
mind while you use it. The LiteShow adapter is a well-constructed adapter for wireless projection. However, in order
to keep it working for you there are several points that you need to pay attention to.
Note: If you have not attached the LiteShow adapter to a projector and installed the LiteShow software on your com-
puter yet, you should go ahead and do so now by following the instructions in the LiteShow Quick Start Guide that came
in your LiteShow packaging.
The LiteShow adapter contains the following features:
LEDs
thumb screws
adjustable
hinge
M1 connector
8
InFocus LiteShow User’s Guide
LiteShow adapter tips
In regards to your LiteShow adapter, keep the following in mind:
•
•
•
•
•
Be careful with the LiteShow adapter: do not drop it or otherwise abuse it. Keep the LiteShow adapter in its carry-
ing case when you are not using it.
The hinge on the LiteShow adapter should be used for positional purposes and repeatedly flexing it is not recom-
mended.
The blinking LEDs on the side of your LiteShow adapter let you know that it is operational and capable of com-
municating with your wireless adapter.
When you secure the LiteShow adapter to the projector with the two thumb screws, be very careful to not over-
tighten them.
Please do not remove the dark plastic top of the LiteShow adapter unless directed to do so by InFocus service and
support personnel.
InFocus LiteShow User’s Guide
9
The LiteShow Splash Screen
Once you’ve attached the LiteShow adapter to a projector and powered that projector on, you should see the LiteShow
Splash Screen, as depicted below.
LiteShow Splash Screen
The LiteShow Splash Screen is a small window that appears in the upper left corner of the projected screen. If you can
see it, then you know that the projector is powered on, the M1 connector is the source, and that a LiteShow adapter is
connected to it.
Once visible, the LiteShow Splash Screen displays the following informational items:
Name: The name of the LiteShow adapter. The default is myLiteShow.
Unique ID: A unique identification string that distinguishes your LiteShow adapter from others in the area.
WLAN: The name of the WLAN LiteShow is connecting to. The default is LiteShow.
Model: The model number of the projector the LiteShow adapter is attached to.
Version: The LiteShow adapter’s current firmware version.
IP: The LiteShow adapter’s IP address. It can be automatically assigned or manually assigned.
10
InFocus LiteShow User’s Guide
If you cannot see the LiteShow Splash Screen after you’ve attached it to a projector and powered the projector on, con-
firm that Auto Source is selected on your projector and that the M1 source is connected. If that doesn’t help, try power-
ing the projector off. Wait a few minutes, until the projector ‘s LEDs let you know it is ready to be powered on, then
reattach the LiteShow adapter and power the projector back on again.
If you are having other trouble getting LiteShow to wirelessly project, consult the “Troubleshooting” and “Frequently
Asked Questions” sections beginning on page 21.
InFocus LiteShow User’s Guide
11
The LiteShow Manager
The LiteShow Manager is your primary tool for controlling the LiteShow adapter and projecting wirelessly. To start it,
navigate to Start>Programs>InFocus>LiteShow and select LiteShow Manager from the open folder. For Apple
users, go to Finder>New Finder Window>InFocus>LiteShow Manager and double-click the LiteShow Manager
icon.
If you opted to place a shortcut to LiteShow Manager on your desktop during installation, you can double-click the
LiteShow Manager desktop icon instead.
Once opened, the LiteShow Manager populates its list window with all LiteShow-enabled projectors found on your
current WLAN.
Project/Stop
button
LiteShow Manager with preferences revealed
Scan button
list window
Settings
button
LiteShow
preferences
box
Hide/Show Preferences
button
12
InFocus LiteShow User’s Guide
The list window
The list window contains four columns:
•
Favorites: When you check this box for a projector, the list window displays these projectors whether their status
is Unknown, In Use, or Available. The Favorites column is helpful because you can quickly locate your most fre-
quently LiteShow enabled projectors here.
•
Projector: By default, the order of projectors is sorted by status and the secondary sort is by projector name. The
first Available projector in the list is highlighted by default. If there are no available projectors in the list, then the
first favorite (see “Show Favorites” on page 15) projector is highlighted by default.
•
•
ID Number: A unique identification string that distinguishes your LiteShow from others in the area.
Status: The Status column indicates whether each projector is Available, In Use, or Unknown.
•
•
•
If a projector is Available you should be able to connect to it.
If a projector is In Use it is being used and cannot be connected to unless the user disconnects from it.
If projector is Unknown it is not on the current WLAN.
Project/Stop button
If an Available or Unknown projector is selected, the Project button is the default button. The Project button is dis-
abled if there are no projectors found.
Note: You can only select an Available or Unknown projector. Projectors that are In Use appear in the list but are
grayed out.
When you select an available projector and click the Project button (or hit the Enter key), the screen projection applica-
tion begins. Once the screen projection application starts (that is, your desktop is shown as the projected image), the
button toggles to Stop and the status of the selected projector flips to In Use.
One of three things can happen when you select a projector whose status is Unknown:
•
The projector is found and is available, which projects the contents of your desktop onto the projection
screen.
InFocus LiteShow User’s Guide
13
•
•
The projector cannot be found (it’s either out of range or turned off), which generates an alert message.
The projector is found but is in use, which generates an alert message.
Scan Button
The Scan button searches for LiteShow-enabled projectors and is active unless you are currently projecting. Once
clicked, the Scan button opens an alert message that lets you know that current network activities will be disrupted
while the scanning process occurs. It is best to close all network related files before continuing. After that, a progress
bar fills during the scan and closes upon completion.
If more LiteShow-enabled projectors are found, they appear in the list window. If no more LiteShow-enabled projec-
tors are found, then you are told that no more LiteShow-enabled projectors were found.
Note: If the Scan button is disabled, consult the OID FAQ on page 22.
Settings Button
The Settings button is enabled when an available projector, or the projector that you are currently using, is selected.
Clicking it opens the Settings window box. The Settings window box, discussed on page 15, contains the Settings tab
and the Diagnostics tab.
14
InFocus LiteShow User’s Guide
Preferences box
The Preferences box is available at the bottom of the LiteShow Manager when the Show Preferences button is clicked.
While it is available, you can click the Hide Preferences button to close it.
Performance Setting
The Performance Setting contains a slide bar with three settings for your desktop’s display resolution that range from
Better Performance to Better Image. Better Performance means a faster display of your desktop by the LiteShow-
enabled projector, while Better Image means that the projected image will be sharper.
The slide bar defaults to the middle setting. The table below shows what the display resolution is for each setting:
System
PC
Left
Middle
Right
800 x 600 x 16
bit color
1024 x 768 x 16
bit color
1024 x 768 x 24
bit color
Mac
800 x 600 x
thousands of
colors
1024 x 768 x
thousands of
colors
1024 x 768 x
millions of col-
ors
The Performance Setting selection is invoked when LiteShow projects. When the projection stops, your previous dis-
play resolution setting (if different) is restored.
InFocus LiteShow User’s Guide
15
Enable encryption while I’m projecting
The default state for Enable encryption while I’m projecting is disabled (not checked). It allows you to project with
security similar to a cabled computer to projector setup.
When the Enable encryption while I’m projecting option is checked, a six-digit code number displays on the pro-
jected image screen after you click the Project button. You need to enter this code when prompted by a window that
asks you to “Enter the code displayed by the projector your wish to use”. Entering this code ensures that your wireless
projection is secure.
Show Favorites
Checking this box allows the LiteShow Manager to show just the projectors that are set as favorites. Favorites are des-
ignated when you check the Favorites checkbox for a projector in the list window’s Favorites column. When this
option is left unchecked, the Favorites column is not available in the list window.
Settings Window
Note: When discussing “Settings,” keep in mind that the Settings Window options are for the LiteShow adapter, while
the settings in the Preferences box are for your computer.
Clicking the Settings button in the LiteShow Manager causes the Settings window to open. When projecting, the Set-
tings button is disabled. The Settings window contains two tabs:
•
•
Settings: The settings provided in the Settings tab are: Projector Name, Network Name (IBSS), Channel, and
IP Address. The LiteShow adapter’s default MAC Address is provided as read-only information.
Note: you can choose to obtain an IP address automatically or specify the IP Address, Net Mask, and Gateway.
However, please be aware that setting a static IP address requires that all computers using the LiteShow-enabled
projector must be set to the same range.
Diagnostics: The Diagnostics tab allows you to check and see if your computer's wireless adapter or USB wireless
adapter is communicating with your LiteShow adapter.
16
InFocus LiteShow User’s Guide
Settings Tab
The fields in the Settings tab are populated with the selected projector’s settings.
LiteShow Settings window - Settings tab
Projector Name: By default, the name is myLiteShow, but you should change it to distinguish it from other LiteShow
adapters on the WLAN. The name you give your LiteShow adapter should be no longer than 32 characters.
Network Name (IBSS): This is the network between your LiteShow adapter and your computer with a wireless
adapter or USB wireless adapter. By default, the name is LiteShow, but you should change it to something unique.
Keep in mind that if you change the name of a network, the network is briefly disrupted.
IP Address: There are two IP options. The first is to Obtain the IP automatically which should work in most cases. If
your network administrator wants you to uses specific address information ask him or her to provide you with an IP
Address, Net Mask, and Gateway.
InFocus LiteShow User’s Guide
17
The MAC address is read only. The MAC address can be useful because it is unique to each LiteShow adapter and
physically resides on the module itself. You can use this to confirm that you are working on the correct module.
Set Password: When you click the Set Password button, the LiteShow Settings Password window opens. It is recom-
mended that you set a password for your LiteShow system, as it keeps your LiteShow Manager settings from being
changed by other users. The following steps explain how to set your password.
1 Click the Set Password button to open the LiteShow Settings Password window.
2 Enter a password between 4 and 16 characters long in the top text field and the retype it in the lower text field to
confirm it.
3 Click the OK button to save the password and close the window. The Settings tab is still open, but the Set Pass-
word button toggles to Change Password. The next time you click the Settings tab, all of its settings and controls
are read-only and the button in the lower reads Enter Password.
When you click the Enter Password button, a password window appears and prompts you for the password. If the
password entered is correct, the text fields and controls in the Settings and Diagnostics tabs are enabled and the
Enter Password button toggles to Change Password.
18
InFocus LiteShow User’s Guide
4 Click OK to close the Settings window and return to the LiteShow Manager.
Note: If you prefer to have no password after setting one up, click the Change Password button, enter your old pass-
word, leave the two New Password fields blank, the click the OK button.
InFocus LiteShow User’s Guide
The Diagnostics Tab
19
The Diagnostics tab contains buttons for blinking the LED and restoring the LiteShow adapter’s factory settings. You
can also set the password from this tab.
LiteShow Settings window - Diagnostics tab
Blink the LED on the LiteShow module: When you click the Blink LED button on the Diagnostics tab, the two green
LEDs on one side of the LiteShow adapter blink. This lets you know that there is communication between the Lite-
Show adapter and your computer's wireless adapter or USB wireless adapter.
20
InFocus LiteShow User’s Guide
InFocus LiteShow User’s Guide
21
Troubleshooting and Frequently Asked Questions
Troubleshooting
LiteShow Manager doesn’t see the projector. Try the following:
•
Make sure that the LiteShow-enabled projector is in range with your computer and that the projector is powered-
on.
•
•
•
•
Click the Scan button.
Make sure that the wireless adapter is installed, plugged in, and enabled on your computer.
Make sure that the wireless adapter’s antenna is switched on or extended.
Make sure that the wireless adapter is configured to match the settings that display on the LiteShow splash screen.
Performance is poor; projection take a long time. Try the following:
•
•
Physically move the computer so that it is closer to the LiteShow adapter.
Check to see that there are no 802.11 or 2.4 GHz devices, such as Bluetooth wireless devices, in the area of the com-
puter and LiteShow adapter.
•
Move the slidebar in the Preferences box to Better Performance.
22
InFocus LiteShow User’s Guide
Frequently Asked Questions
The following are questions that you may have about the LiteShow system and its individual parts.
Q: I received a message telling me that no wireless adapter or USB wireless adapter with OID support was
found. What should I do?
A: No matter how new a computer and wireless adapter or USB wireless adapter are, they may need new drivers. It is
recommended that you go to your computer's and wireless adapter’s or USB wireless adapter's websites and see if
newer drivers exist. If so, consider downloading and installing them. If newer drivers aren't available, contact your
equipments' technical support areas and inquire about updated drivers that support OIDs. It's very likely that if you
did not purchase your wireless device bundled as part of your LiteShow package, it will need its drivers updated.
Q: When projecting, I switched the computer’s screen area to 640x480 pixels and the projected image shrank to
50% height but stayed at 100% width. What’s wrong?
A: Unfortunately, 640x480 pixels is not a supported mode. Make sure that you are projecting from modes that are
800x600 or higher.
Q: Why does my computer or my desktop icons flicker, or my task bar go blank when I click the Project button?
A: It is likely that your computer is switching resolutions.
u. If you are unsure how to change the projector’s mode, consult the User’s Guide that came with it
Q: Why does my animated cursor not animate on the LiteShow-enabled projection?
A: Some cursors do not “animate” in the projected image. This can be the nature of animated cursors in wireless pro-
jection as it displays the desktop to the projected screen. Animated cursors are not recommended for use in LiteShow
projections.
Q: Is it okay to remove the plastic top from the LiteShow adapter?
InFocus LiteShow User’s Guide
23
A: Unless directed to remove it by InFocus technical service personnel, leave the plastic top on the LiteShow adapter at
all times.
Q: What does the star (or asterisk *) mean on the Splash Screen?
A: Should you see a star (or asterisk *) in the LiteShow Splash Screen, it indicates that USB services are not available on
the projector. Contact InFocus Technical Support (see “If you need assistance” on page 5) to resolve this problem.
Q: How do I restore the LiteShow adapter’s defaults to what they were when I received it?
A: You should only reset the LiteShow settings on the advice of InFocus technical support personnel. InFocus Techni-
cal Support contact information can be found in “If you need assistance” on page 5.
24
InFocus LiteShow User’s Guide
InFocus LiteShow User’s Guide
25
Glossary
802.11: IEEE 802.11 specifications are wireless standards that specify an over-the-air interface between a wireless client
and a base station or between two wireless clients, such as the LiteShow adapter and a computer’s wireless adapter or
USB wireless adapter.
Access point: A base station in a wireless LAN. LiteShow does not require an access point.
Ad-hoc Mode: Ad-hoc mode, also known as “peer-to-peer” mode, allows wireless devices to communicate with each
other directly and without the need of an access point. This is an Independent BSS (IBSS).
BSS: In 802.11 systems, each access point and each wireless device are known as a Basic Service Set (BSS).
Encryption: The process of encoding data so that it inaccessible during transmission.
Firmware: A type of memory chip that retains its content without electrical power.
IBSS: In ad hoc mode wireless devices can communicate with each other directly and do not use an access point. This
is known as an Independent Basic Service Set (IBSS).
DCHP: Also know as Dynamic Host Configuration Protocol software. DHCP automatically assigns IP addresses to cli-
ent stations logging onto a TCP/IP network. It eliminates the need to manually assign permanent IP addresses.
IEEE: Institute of Electrical and Electronics Engineers, New York, (www.ieee.org)
IP Address: The address of a computer attached to a TCP/IP network. Every client and server station must have a
unique IP address. It can be provided by the user, network administrator, or obtained automatically.
LAN: Local Area Network. A computer network that exists over a small area. LANs are generally found in a single
building or group of buildings. LANs can be connected to other LANs over any distance by telephone lines and radio
waves. A system of LANs connected in this way is called a wide-area network (WAN).
USB wireless adapter: a wireless device that attaches to a PC computer through a USB port.
26
InFocus LiteShow User’s Guide
Wi-Fi: Short for wireless fidelity. The term is commonly used when referring to any type of 802.11 network.
Wireless Adapter: a wireless PCMCIA card, integrated adapter, or USB wireless adapter that inserts into a PC laptop
computer.
WLAN: A wireless LAN that transmits over the air, typically in an unlicensed frequency such as the 2.4GHz band.
InFocus LiteShow User’s Guide
27
Appendix
Specifications
Te m pe r at ure
Operating
50 to 104° F (10 to 40° C) at sea level
50 to 95° F (10 to 35° C) at 10,000 feet
-4 to 158° F (-20 to 70° C)
Non-operating
Altitude
Operating
Non-operating
0 to 10,000 feet (~ 3,000m)
0 to 20,000 feet (~6,000m)
10% to 95% relative humidity, non-condensing
50 to 104° F (10 to 40° C)
Humidity
.83 in x 2.56 in x 3.66 in (21mm x 65mm x
93mm)
Dimensions
6.17 oz (175g)
M1-D
Weight
Port
Up to 300 ft (100m)
11Mbps
Range
Data Rate
28
InFocus LiteShow User’s Guide
5V DC @ 750mA
Input
Accessories
The LiteShow system comes with the following accessories, except where noted:
LiteShow adapter
Wireless adapter *
Protective sleeve
User’s Guide
591-0260-01
412-0003-xx
110-0682-xx
010-0449-xx
009-0801-xx
010-0446-xx
Quick Start Guide
LiteShow CD
* when purchased with the LiteShow system with a bundled wireless adapter from 3COM.
InFocus LiteShow User’s Guide
29
Compatible projectors
The following table contains projector models that have been tested and are known to be compatible with the Lite-
Show wireless projection system.
InFocus
Proxima
ASK
LP70
DP1000x
DP1200x
DP6500x
C200
M1
LP120
LP130
LP335
LP340
LP350
LP500
LP530
LP650
LP925
LP930
M2
30
InFocus LiteShow User’s Guide
InFocus LiteShow User’s Guide
31
Numerics
24-bit color depth 3
802.11 25
802.11b 2
A
Access point 25
accessories 28
Ad-hoc Mode 25
animated cursor 22
assistance 5
Available projector 12
B
Blink the LED 19
C
Channel 16
compatible projectors 29
Contents 4
D
data rate 3
Diagnostics tab 19
Blink the LED 19
documentation 5
E
e-mail 5
Enable encryption 15
32
InFocus LiteShow User’s Guide
encryption 25
F
Favorites 12, 15
firmware 25
I
icons flicker 22
IEEE 25
image shrank 22
IP Address 16, 25
L
LAN 25
list window 12
Available 12
ID Number 12
In Use 12
Projector 12
Status 12
Unknown 12
LiteShow adapter 7
features 7
tips 8
LiteShow doesn’t see the projector 21
LiteShow Manager 3, 11
list window 12
InFocus LiteShow User’s Guide
33
LiteShow Splash Screen 9
IP 9
Model 9
Name 9
Unique ID 9
Version 9
WLAN 9
LiteShow-compatible projectors 29
M
M1 connector 3, 9
MAC address 17
N
Network Name 16
O
Obtain the IP automatically 16
OID support 22
Optional accessories 29
P
password 17
Performance issues 21
Performance Setting 14
Preferences box 14
Project button 12
Projector Name 16
34
InFocus LiteShow User’s Guide
Q
Quick Start Guide 1
R
range 3
register your LiteShow 2
S
Scan button 13
Set Password 17
Settings button 13
Settings tab 16
Channel 16
IP Address 16
MAC address 17
Network Name 16
Projector Name 16
Settings window 15
Diagnostics 15
Settings 15
Show Favorites 15
Specifications 27
static IP address 15
Stop button 12
T
Technical Support
in Europe 5
in USA 5
InFocus LiteShow User’s Guide
35
Troubleshooting 21
W
website 5
WEP 25
Wi-Fi 25
Wireless Adapter 26
WLAN 26
X
XGA 3
36
InFocus LiteShow User’s Guide
LiteShow User’s Guide
37
One-Year Warranty
Limited Warranty
Subject to the Limitations, Exclusions and Disclaimers hereof, InFocus Corporation ("InFocus") warrants that the Pro-
jector, Lamps and Accessories (hereinafter collectively or individually referred to as "Product" as appropriate) pur-
chased from InFocus, an InFocus distributor, or an InFocus reseller will conform to InFocus' specifications and be free
from defects in material or workmanship for the respective Limited Warranty period provided below. InFocus does
not warrant that the Product will meet the specific requirements of the end-user customer.
If the Product, while subject to this Limited Warranty, is defective in material or workmanship during the warranty
period, then InFocus, at its option, will REPAIR or REPLACE the Product.
All exchanged parts and Products replaced under this Limited Warranty will become property of InFocus. InFocus'
sole obligation is to supply (or pay for) all labor necessary to repair the Product found to be defective within the Lim-
ited Warranty period and to repair or replace defective parts with new parts or, at the option of InFocus, serviceable
used parts that are equivalent or superior to new parts performance. Limited Warranty periods are as follows:
•
•
Projector Product Limited Warranty Period (Excluding Lamps): one (1) year from date of purchase.
Lamp Product Limited Warranty Periods: From the date of Projector Product purchase, the original installed
lamp shall have a 90-day or 500 hours usage Limited Warranty Period, whichever comes first, and replacement
Lamps purchased at the time of Projector Product purchase will have a 90-day or 500 hours usage Limited War-
ranty period, whichever comes first.
•
•
LiteShow Wireless Products: One (1) year from date of purchase.
Accessory Product Limited Warranty Period: one (1) year from date of purchase.
WARRANTY LIMITATION AND EXCLUSION
THIS WARRANTY SETS FORTH INFOCUS' MAXIMUM LIABILITY FOR ITS PRODUCT. THIS WARRANTY
EXTENDS ONLY TO PRODUCTS PURCHASED FROM INFOCUS OR AN INFOCUS AUTHORIZED RESELLER.
InFocus shall have no further obligation under the foregoing Limited Warranty if the Product has been damaged due
to abuse, misuse, neglect, smoke exposure (cigarette or otherwise), accident, unusual physical or electrical stress,
38
LiteShow User’s Guide
unauthorized modifications (including use of an unauthorized mount), tampering, alterations, or service other than by
InFocus or its authorized agents, causes other than from ordinary use or failure to properly use the Product in the
application for which said Product was intended.
This Limited Warranty excludes Product cleaning, repair, or replacement of plastics due to cosmetic damage and dam-
age as a result of normal wear. Product repair outside of the terms of the Limited Warranty will be on a time and mate-
rials basis. Prolonged Product "demonstration" causes unusual Product wear and is not considered normal use under
the terms of this Limited Warranty.
The Accessory Product Limited Warranty covers the accessory item only and excludes normal wear. The Lamp Prod-
uct Limited Warranty excludes expected lamp degradation.
Remanufactured Products and Software Products are exempt from the foregoing Limited Warranty. Please refer to the
appropriate Remanufactured Product Limited Warranty or Software Product Limited Warranty for applicable War-
ranty information.
DISCLAIMER OF UNSTATED WARRANTIES
THE WARRANTY PRINTED ABOVE IS THE ONLY WARRANTY APPLICABLE TO THIS PRODUCT. ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE ARE DISCLAIMED. THERE ARE NO WAR-
RANTIES THAT EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF AND THE FOREGOING WAR-
RANTY SHALL NOT BE EXTENDED, ALTERED OR VARIED EXCEPT BY WRITTEN INSTRUMENT SIGNED BY
INFOCUS. SOME JURISDICTIONS DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY
MAY LAST, SO SUCH LIMITATIONS MAY NOT APPLY TO YOU.
Limited Warranty Period
The Limited Warranty periods hereof commence on the date of purchase by the end-user customer. These Limited
Warranty provisions shall apply only to the end-user purchaser (first person or entity that purchased a new Product
for personal or business use and not for the purpose of distribution or resale). SOME JURISDICTIONS MAY GRANT
LiteShow User’s Guide
39
YOU CONSUMER RIGHTS WITH MINIMUM WARRANTY DURATION THAT DIFFER FROM THE DURATIONS
PROVIDED HEREIN, AND INFOCUS WILL HONOR ALL SUCH CONSUMER RIGHTS.
To Be Eligible For Limited Warranty Coverage
Any person exercising a claim under this Limited Warranty must establish to the satisfaction of InFocus both the date
of purchase and that the Product was purchased new. The sales receipt or invoice, showing the date of purchase of the
Product is the proof of the date of purchase.
To Obtain Warranty Service
During the Limited Warranty period, to exercise this Limited Warranty, the purchaser must first contact 1) InFocus, 2)
a service facility authorized by InFocus or 3) the place of original purchase.
InFocus Customer Service - 1-800-799-9911 or [email protected]
For Warranty service, the purchaser will be advised to return or deliver the defective Product freight and all fees pre-
paid, to an InFocus Service Center or to a service facility authorized by InFocus. When returning Product to InFocus, a
Return Material Authorization Number (RMA #) is required and must be clearly displayed on the outside of the ship-
ping carton or a similar package affording an equal degree of protection. InFocus or the service facility authorized by
InFocus will return the repaired/replaced Product freight prepaid to the purchaser.
Products returned for Warranty service must be accompanied by a written letter that: (i) explains the problem; (ii) pro-
vides proof of date of purchase; (iii) provides the dealer's name; and (iv) provides the model and serial number of the
Product. Upon request of InFocus Corporation or an authorized repair center for InFocus, proof of legal import must
accompany the warranty repair Product, otherwise the Product must be returned to the place of original purchase, to
the manufacturer (Purchaser must bear all tax, duty and freight), or the Purchaser must bear charges for the warranty
repair.
No repair or replacement of Product or part thereof shall extend the Limited Warranty period as to the entire Product.
Warranty on the repair part and workmanship shall only be effective for a period of ninety (90) days following the
repair or replacement of that part or the remaining period of the Product Limited Warranty whichever is greater.
40
LiteShow User’s Guide
LIMITATION OF LIABILITY
IT IS UNDERSTOOD AND AGREED THAT INFOCUS' LIABILITY WHETHER IN CONTRACT, IN TORT, UNDER
ANY WARRANTY, IN NEGLIGENCE OR OTHERWISE SHALL NOT EXCEED THE RETURN OF THE AMOUNT OF
THE PURCHASE PRICE PAID BY PURCHASER AND UNDER NO CIRCUMSTANCES SHALL INFOCUS BE LIA-
BLE FOR SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LOST PROFITS, LOST REVE-
NUES OR LOST SAVINGS. THE PRICE STATED FOR THE PRODUCTS IS A CONSIDERATION IN LIMITING
INFOCUS' LIABILITY.
Limitation on Bringing Action - No action, regardless of form, arising out of the agreement to purchase the Product
may be brought by purchaser more than one year after the cause of action has accrued.
Governing Law - Any action, regardless of form, arising out of the agreement to purchase the Product is governed by
Oregon law.
Mandatory Arbitration - Any action, regardless of form, arising out of the agreement to purchase the Product is sub-
ject to mandatory arbitration.
SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUEN-
TIAL DAMAGES SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. THIS LIMITED WAR-
RANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS, DEPENDING ON
JURISDICTION.
LiteShow Wireless Products Software Warranty Statement
You agree that this SOFTWARE PRODUCT is provided by InFocus "AS IS" without any warranty of any kind. InFocus
has no responsibility or liability for any bug or defect fixes or service support. ACCORDINGLY, TO THE MAXIMUM
EXTENT PERMITTED BY APPLICABLE LAW NO WARRANTIES ARE PROVIDED BY INFOCUS, AND INFOCUS
AND ITS SUPPLIERS DISCLAIM ALL WARRANTIES AND CONDITIONS, EITHER EXPRESS, IMPLIED OR STATU-
TORY,
LiteShow User’s Guide
41
INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTIC-
ULAR PURPOSE, TITLE, AND NON-INFRINGEMENT, WITH REGARD TO THE SOFTWARE PRODUCT AND THE
PROVISION OF OR FAILURE TO PROVIDE SUPPORT
SERVICES. THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY HAVE OTHERS,
WHICH VARY FROM STATE/JURISDICTION TO STATE JURISDICTION. To the extent implied warranties may not
be entirely disclaimed but implied warranty limitations are
allowed by applicable law, implied warranties on the SOFTWARE PRODUCT, if any, are limited to ninety (90) days.
LIMITED WARRANTY ON MEDIA
Notwithstanding the foregoing, InFocus warrants the media on which the InFocus Software is recorded and delivered
by InFocus to be free from defects in materials and workmanship under normal use for a period of ninety (90) days
from the date of original purchase. Your exclusive remedy under this Section shall be, at InFocus's option, a refund of
the purchase price of the product containing the InFocus Software or replacement of the InFocus Software which is
returned to InFocus or an InFocus authorized representative with a copy of the receipt. THIS LIMITED WARRANTY
AND ANY IMPLIED WARRANTIES ON THE MEDIA INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WAR-
RANTIES OF MERCHANTABILITY, OF SATISFACTORY QUALITY, AND OF FITNESS FOR A PARTICULAR PUR-
POSE, ARE LIMITED IN DURATION TO NINETY (90) DAYS FROM THE DATE OF
ORIGINAL PURCHASE. THE LIMITED WARRANTY SET FORTH HEREIN IS THE ONLY WARRANTY MADE TO
YOU AND IS PROVIDED IN LIEU OF ANY OTHER WARRANTIES
(IF ANY) CREATED BY ANY DOCUMENTATION OR PACKAGING. THIS LIMITED WARRANTY GIVES YOU SPE-
CIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY BY JURISDICTION. LIMITA-
TION OF LIABILITY. TO THE MAXIMUM EXTENT
PERMITTED BY APPLICABLE LAW, IN NO EVENT SHALL INFOCUS OR ITS SUPPLIERS BE LIABLE FOR ANY
SPECIAL, INCIDENTAL, INDIRECT, OR CONSEQUENTIAL
42
LiteShow User’s Guide
DAMAGES WHATSOEVER (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS PROF-
ITS, BUSINESS INTERRUPTION, COMPUTER INTERRUPTION, LOSS OF BUSINESS INFORMATION, OR ANY
OTHER PECUNIARY LOSS) ARISING OUT OF THE USE OF OR INABILITY TO USE THE SOFTWARE PRODUCT
OR THE PROVISION OF OR FAILURE TO PROVIDE SUPPORT SERVICES, EVEN IF INFOCUS HAS BEEN
ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES. BECAUSE SOME STATES AND JURISDICTIONS DO NOT ALLOW THE
EXCLUSION OR LIMITATION OF LIABILITY, THE ABOVE
LIMITATION MAY NOT APPLY TO YOU.
|