Washing machine
WG1285WG
Overview
E
F
H
L
O
D
G
I
M
A
N
B
C
A. Programme selector
F.Spin cancel button
Use this dial to select one of the 15 wash programmes
available for all your laundry requirements (see programme
table on page 5).
Use this button to exclude the spin cycle. This function should
be used only for items that are difficult to iron and only with
the synthetics and delicate fabrics programmes.
Remember that this dial should be turned in a clockwise
direction and only when the machine is off.
G. Slow spin button
Use this button to reduce the spinning speed from 1200 to
600 rpm for the cotton and linen programmes and from
850 to 600 rpm for the synthetic fabrics programmes.
B. Detergent
dispenser
The detergent dispenser has
three compartments marked
1, 2 and 3:
3
H. Heavy soil button
2
1
Depression of this button introduces cold soaking and gradual
water temperature change.A suitable "biological" detergent
should be used.The cycle should remove most water soluble
stains, blood, wine, sauce, etc., provided the stain has not
been fixed by previous immersion in or treatment with hot
water. Fabrics which are accidentally stained and then
immersed or washed in hot water will invariably be
permanently dyed by the stain colour.It is vitally important,
when using the stain removal cycle, to understand that the
initial water soaking is cold with a gradual temperature build
up and extensive biological washing. Please note only
colour fast fabrics (as above) should be subjected to
stain removal.
1
2
3
prewash detergent
wash detergent
fabric softener.
C. ON-OFF button
This button turns your appliance ON/OFF.Press button C to
turn on the washer and depress button C to turn off the
washer.
D. Ecoultra button
Depression of this button makes drum rotate at a slower
speed, resulting in less stress, wear and tear on your clothes.
Button gives best result with loads of 3 kilos or less.
This button reduces water consumption when rinsing if the
machine does not have a full load.
E. Energy saver button
I. Rapid wash button
Push in on programmes 1 and 2 when washing less heavily
soiled articles.This will reduce the maximum wash tempera-
ture and energy consumption.
This function shortens the duration all the wash programmes.
Ideal for laundry which is not heavily soiled and is especially
useful for programmes 4 and 10.
GB
2
L. Anti-crease button
M. Door lock Indicator light
This function interrupts the cycle so that the laundry is left
soaking in water before the spin cycle.
Door lock:lights up during the wash programme, while the
door is locked and turns off at the end of the programmes
when the door safety mechanism unlocks the door.
This function is extremely useful because it stops delicate or
synthetic fabrics from creasing (for example when one has
to wait several hours before removing the laundry load).
It should be used only with the programmes for synthetic
fabrics and woollens.
N. Heating Indicator light
Heating: lights up during the water heating.
IMPORTANT:Before opening the door, drain away the water
by setting knob A on "drain". To carry out the spin cycle,
simply press L.
O. ON/OFF Indicator light
When this is lit, the machine is on.
Using your washer
Compartment 1
Prewash cycle detergent
(powder)
Compartment 2
Wash cycle detergent
(powder or liquid)
Compartment 3
Fabric softner
Preparing your laundry....
Divide your laundry by fabric and colour fastness.Wash white
and coloured items separately.
Remember to empty pockets, removing especially those small
items like coins, paper, pins and badges that might jam the
pump.Fasten or remove loose buttons and fasten zippers.
Turn shirts inside out for better results.
3
2
1
Check wash labels
Never fill compartment 3 above the grid.
Garments and laundry generally have wash instruction labels
(which tell you if they shloud be dry-cleaned, hand washed
or machine washed) showing the wash temperature, how
to iron etc.
Important: fabrics should only be machine washed if their
labels show the appropriate symbol (see table 1 page 4).
Use compartment 2 for liquid detergent, filling the
compartment just before you start the washer.Remember
that liquid detergent is ideal for wash cycles with
temperatures up to 60°C and for the programmes with no
prewash cycle.Dispensers for liquid and powder detergents
which are placed inside the drum of the washer, are sold on
the market.
To improve the effectiveness of the washing cycle, we
recommend that you insert a detergent dispenser in the drum
before loading the laundry.
Alternate small and large items when
loading your washer
This washer has an electronic load balancing control:before
carrying out the spin cycle, this device ensures that the
laundry is arranged as evenly as possible in the drum,
according to the type of fabric and the way it was initially
loaded. This will minimize vibration and noise even during
the fastest spin cycle. For best results however, we
recommend you alternate small and large items when you
load your washer remember to spread them out;never wash
large loads of terry cloth items.
Do not use hand washing detergents since these produce
very heavy suds.
When using cold wash cycles, remember to reduce the
detergent dosage.
Detergents and fabric softener
Open detergent dispenser B by pulling it outwards.Fill with
detergent and conditioner using the quantities indicated by
the manufacturer on the packet according to the load you
are washing, the water hardness and how soiled your laundry
is.As you become more familiar with your washer, you will
regulate the quantities according to your own personal
experience.
GB
3
1. Understanding the labels
Strong
action
Not
washable
in water
Wash at
95°C
Wash at
60°C
Wash at
40°C
Wash at
30°C
Wash
Hand wash
Delicate
action
c
l
Bleaching Do not
Bleachin
Ironing
only in
bleach
cold water
Hot iron Medium hot Iron at
Not
at max
200°C
ironing at max 100°C ironable
max 150°C
A
F
P
Dry clean Dry clean
with any only with,
Dry clean Do not dry
with av. clean
benzine,
solvent
perchloride
benzine
Dry
pure
cleaning
av., pure
alcohol,
R111 and
R113
alcohol
and R113
High
Temperat
Machine
dryable
Do not
machine dry dry
Spread to Hang to
Dry on
clothes
dry
Drying
Starting up your washer
Run the first wash without laundry using programme
2 at 90°C.
At the end of the wash cycle...
Wait for indicator light M to turn off (about three minutes),
switch off the washer by setting the ON/OFF button C to O
(OFF);you can now open the door.Once you have removed
your clean laundry from the washer, remember to leave the
door open or at least ajar (this will prevent the formation of
an unpleasant odour) and shut off the water supply.
Load your laundry in the washer, add the detergent and
fabric softener and remember to:
- shut the door properly
- plug the washer in at the mains
- turn on the water supply
- check that button C is not pressed in (position O)
Selecting the programme
The table on pages 5 will help you choose the right
programme.Turn dial A to the programme number you have
chosen and, if necessary, press functions buttons D, E, F, G,
H, I, L; set ON/OFF button C to position I (ON).
GB
4
Selecting the programmes
The description of the wash programme by type of fabric is shown on the detergent dispenser.
Fabrics and degree of dirtiness
COTTONS
Program. Prewash Wash
Softner Description of wash cycle
knob
detergent detergent
Heavily soiled white laundry
(sheet, table cloths. etc.)
Warm prewash, wash at 90°C, rinse cycles,
softener, spin cycle
◆
◆
◆
◆
◆
1
2
Very soiled white fabrics and fast colours
(coloured laundry, dressing gowns,
vests, etc.)
Wash at 90°C, rinse cycles, softener,
spin cycle
Lightly soiled white fabrics and resistent
colours (coloured laundry, shirts etc.)
Wash at 60°C, rinse cycles, softener,
spin cycle
◆
◆
◆
◆
3
4
Non fast colours
(shirts, vests, dresses, etc.)
Wash at 40°C, rinse cycles, softener,
spin cycle
Rinse cycles
Rinse cycles, softener, spin cycles
Rinse cycles, softener, spin cycles
Strong spin
◆
◆
5
6
7
Softner
Spin
SYNTHETICS
Colour fast synthetics
Wash at 60°C, rinse cycles, softener,
non crease or delicate spin
◆
◆
◆
◆
◆
◆
◆
◆
8
Normally soiled colour fast synthetics
(bouses, skirts, etc.)
Wash at 50°C, rinse cycles, softener,
non crease or delicate spin
9
Non fast coloured synthetics
(all kinds of slightly soiled laundry)
Wash at 40°C, rinse cycles, softener,
non crease or delicate spin
10
12
13
14
Rinse cycles
Rinse cycles, softener, non crease,
spin cycles
Softner
Rinse cycles, softener, non crease,
spin cycles
Spin
Delicate spin cycle
DELICATE FABRICS
Woollens (machine washable)
Wash at 40°C, rinse cycles, softener,
non crease or delicate spin
◆
◆
◆
◆
11
12
13
Rinse cycles
Softner
Rinse cycles, softener, non crease,
spin cycles
Rinse cycles, softener, non crease,
spin cycles
Spin
Delicate spin
14
15
Drain
Drain with no spin
GB
5
Washing tips
Stain removal
What not to wash in your appliance?
The most common stains will disappear during the wash. If
they are particularly stubborn, soak the garment in water
and rub a little detergent onto the stain before putting it in
the washing machine.
Greasy marks (especially old ones) need treating with a stain-
remover. Be careful not to mark the fabric with remover.
- Torn, frayed or unhemmed items; in order to wash items
of this kind, wrap them in a linen bag to prevent them from
tearing during the wash.
- Dark coloured items with white items.Dark items should
be washed separately .
Curtains
Pre-treatment for awkward stains
Curtains tend to crease badly.Try this washing hint to prevent
creases:fold the curtains carefully and place in a pillow case
or loose mesh bag; wash separately ensuring that the weight
is no more than a half wash load.
- Ink:ball point/felt tip;Put a few drops of nail varnish remover
or surgical spirit onto a piece of cotton wool and dab the
stain.Wash at 90°C (NB.This is only suitable for colourfast
cottons)
- Tar and oil; Scrape off any thick tar or oil on the surface.
Soften the remainder with margarine or butter and wipe
away with a clean cloth. Treat any residual stain with
turpentine, then wash according to the fabric
- Wax; Scrape off, then put the stained garment between
two pieces of blotting paper and press with a hot iron.Dab
the stain immediately with cotton wool dipped in turpentine
- Chewing gum; Apply nail varnish remover to the gum,
then remove it carefully
Quilts, tennis shoes and wind-cheaters
Contrary to common belief, goose or duck down quilts and
wind-cheaters, can in fact be machine washed, provided
the instructions shown on the label are followed carefully.
Remember however to load no more than 2-3 kg of laundry
and to repeat the rinse cycle once or twice following with a
gentle spin. In the case of tennis shoes, wipe off mud and
then machine wash with denims or heavy fabrics (but not
white fabrics).
- Lipstick;Pretreat with a liquid detergent using the dosing
ball, rub vigorously and rinse before washing
- Grass; Soak in a warm washing solution using a biological
washing product, then wash according to the fabric.
Alternatively, saturate the stain with white methylated spirit.
Rinse and wash normally
- Paint:Water based latex, acrylic and school paints, emulsion
paints;Treat stains while still wet. Rinse thoroughly under
running water to flush out the paint, then wash according
to the fabric.
Oil based paint/varnish; Sponge with white spirit or paint
brush cleaner before washing in the normal way.
Do not exceed the recommended weights
shown in the table
For best washing results, do not exceed the recommended
weights shown in the table;the weights shown refer to dry
laundry.
Maximum dry laundry
load
How heavy is your
laundry?
heavy fabrics
1 sheet 400-500 g
maximum 5 kg
delicate fabrics
maximum 2 kg
pure new wool
maximum 1 kg
mixed loads
1 pillow case 150-200 g
1 table cloth 400-500 g
1 bathrobe 900-1200 g
1 bathroom towel150-250 g
maximum 2,5 kg
GB
6
Energy saving hints
-Try to wash complete laundry loads:this saves unnecessary
consumption of water and energy.
-Your washer features automatic consumption control, this
means that you can wash laundry loads from 1 - 5 kg with
considerable savings. Your washer will use just the right
amount of water and electricity. All you need to do is dose
the detergent.
- Fabric softeners: always use a softener; not only do these
perfume and soften your laundry, they also make it easy to
iron, saving you time.
- Select the right programme for your laundry: this will
obviously depend on the type of fabric and how soiled your
laundry is;we recommend the use of programmes without
prewash which will save you time, water and energy. The
prewash cycle should in fact be used only for heavily soiled,
cotton fabrics.
- Set the right temperature:use temperatures above 60°C
only for very stubborn dirt but remember that modern
detergents are very efficient even at low temperatures.
- Use the correct quantities of detergent: do not use too
much detergent; remember that not only will this make
rinsing more difficult but also pollutes the enviroment.
- Use the economy buttons: when washing small laundry
loads use the Economy button if available on your washer
and reduce the detergent quantity.
General maintenance
After every wash
When moving house
Leave the door open and wipe the door gasket dry after
each wash so that damp or odours do not form.
When you move, all you need to do is secure the inside of
the machine with the transit screws (supplied with the
packaging of the machine) so that it will not be damaged.
Remove the plug
Cleaning and special servicing
Before cleaning or servicing always remove the plug from
the socket. This is for safety reasons.
Hose
No solvents or abrasive substance
Check the hose once a year. It should be replaced if any
signs of splitting or damage can be seen. The machine is
under a lot of strain while operating and this may cause a
cracked hose to split open suddenly.
You do not need solvents or abrasive substances to clean
the outside of the washing-machine and the rubber parts.
Just use a cloth, warm water and soap.
Detergent dispenser
drawer
Inspecting the drain pump
Your washer has a self-cleaning pump and therefore requires
no cleaning or mainteannce. Remember however that small
items such as buttons or coins may accidentally fall into the
pump.To remove these items, the pump comes equipped
with an "prechamber" which is accessible from the front of
the pump.To gain access to this prechamber simply remove
the panel located on the bottom part of the washer
(figure 1), place it on the ground near the machine
(figure 2), and remove the lid by turning it in the counter
clockwise direction.Carefully inspect the inside of the pump.
Important: before removing the lid check that the wash
cycle has ended and unplug the washer from the mains.It is
normal for a small quantity of water to spill out once the lid
is removed.The panel positioned at the base of the machine
will catch the water that spills out. Remember to shut the lid
firmly when you replace it.
This can be removed and
cleaned. Just pull it towards
you, as shown in the diagram,
and leave it under running
water for a few minutes.
Unplug the machine when you go away
It’s best to unplug the machine when you go away, turn off
the water supply and leave the machine door open or ajar.
The drum and rubber door lining will dry and no unpleasant
odours will form inside.
GB
7
Removing limescale
Water contains increasing amounts of limescale because of
pollution. If you live in a hard water area in addition to
using water-softener in each wash, it is a good idea to put
the machine through a cycle without laundry or detergent,
just using limescale remover.
1
1
2
Fig. 1
Fig. 2
Trouble shooting
If the machine does not seem to be working properly before
calling the service engineer there are a number of things
you can check. Perhaps you have forgotten to push in a
button or you are not using the machine properly.
Lots of vibration during the spin
Make sure:
the internal oscillating unit was released correctly at the time
of installation (see installation instructions); the washer is
levelled correctly or too tightly fitted between furniture units
and the wall.
Machine won't start
Make sure:
the appliance is plugged to the mains socket; you have
electricity in your home, the door is firmly shut, the ON/OFF
button C is on I, the programming cycle knob, in washers
which have one, is on O, the programme is properly set and
the mains water tap is open.
Your washer is leaking.
Make sure:
the ring nut of the supply pipe is firmly tightened; the
detergent dispenser is not plugged and the drainage pipe is
firmly fixed.
Machine won't fill
Excessive formation of suds.
Make sure:
Make sure:
the water tap is open and connected correctly to the hose;
the water mains has not been cut off and that water pressure
is sufficient;also check the hose for kinks.
the type of detergent you have used - is it suitable for an
automati washer - have you used too much detergent?
Water is pumping in and out all the time
If despite all this your washer is still not running properly, call
your local Authorized Service Centre providing the
following information:
Make sure:
there are no kinks in the drain pipe and that it is at least at a
height of 60-100 cm; the pipe mouth is not below water
level and that the wall drain has no air outlet.If the problems
continue even after you have checked these points, shut
the water tap and turn off your washer.
-
-
fault
model code (Mod. ....)
and serial number (S/N ....)
shown on the data plate at the back of your washer.
Problems with pumping out water or
spinning
Never use the services of an unauthorised servicing technician
and insist on the use of original spare parts.
Make sure:
the programme selected has a draining cycle; the non
creasing "hydropstop" button, on washers which have one,
has not been pressed accidentally;the drainage pump is not
jammed; the drain pipe is bent; the drainage piping is
plugged; any drainage pipe extensions are properly
connected and do not prevent water flow.
GB
8
Installation
Transit packing
After removing the packing, check the appliance for damage.
If you have any doubts do not use the washer and call a quali-
fied technician. Keep the packaging components (plastic bags,
polyester foam, nails etc.) out of the reach of children since
they could be dangerous.The interior of the washer, has an
oscillating unit which is fixed on the back by 3 screws during
transport (fig. 3). Before starting up the washer, release the
unit, by unscrewing the 3 screws. Seal the screw holes with
the plastic plugs supplied with the appliance.
Fig. 6
Fig. 5
Drain hose
The drain hose (hooked pipe) is secured to the rear of the
machine by support clips and may be routed to right or left
as required (see fig.7).The drain hose should be placed in a
stand pipe with a minimum internal diameter of 38 mm (1½
inches) or it can be positioned over a sink (see fig. 8) or it
can be connected as shown in fig. 9. The height of stand
pipe or sink should be between 60 and 100 cm (24 and 40
inches).Care must be taken that the hose is not obstructed,
twisted, submerged or kinked. If the hose is connected with
an airtight joining, provision should be made to prevent
syphoning.
Fig. 3
Fig. 4
Levelling
The washer must be perfectly levelled.To level the appliance,
only the front feet need to be adjusted (see fig.4);remember
that the inclination of the working surface must not be more
than 2 degrees.If the washer is installed on a carpeted floor,
check that there is sufficient ventilation space between the
floor and the bottom of the washer.
Water supply
Both hot and cold water supplies are preferable and they
should be between 34.5kN/m²(5lb/in²) and 1034.2kN/m²
(150lb/in²) pressure. The hose having the red end fitting
should be encountered between the hot supply and the
threaded connection adjacent to the letter H on the rear of
the machine. The hose having the white end fittings should
be connected between the cold supply and the threaded
connection adjacent to the letter C on the rear of the ma-
chine (see fig. 5). Remember to insert a sealing washer at
each connection to ensure watertight joints. Do not
overtighten the connections by using tools -hand tight is
sufficient to prevent leaks.It is generally more convenient to
have these supplies away from the sink taps. Where no
suitable hot water supply is available or it does not meet
these requirements, both inlet hoses may be connected to a
cold supply by using two taps etc., or a «T» junction on the
plumbing (see fig. 6) however, use of cold water only will
increase programme times.
Fig. 7
Fig. 8
Fig. 9
Note: the maximum temperature should not exceed 70°C
(158°F).
GB
9
How to connect an alternative plug:
The wires in this mains lead are coloured in accordance with
the following code:
Electrical connection (figure 10)
Your appliance is now supplied with a 13 amp fused plug it
can be plugged into a 13 amp socket for immediate use.
Before using the appliance please read the instructions below.
BLUE
NEUTRAL (N)
LIVE (L)
BROWN
GREEN&YELLOW EARTH (E)
WARNING-THISAPPLIANCEMUSTBEEARTHED.
THEFOLLOWINGOPERATIONSSHOULD BECARRIEDOUT
BYAQUALIFIEDELECTRICIAN.
Disposing of the appliance:
When disposing of the appliance please remove the plug by
cutting the mains cable as close as possible to the plug body
and dispose of it as described above.
Replacing the fuse:
When replacing a faulty fuse, a 13 amp ASTA approved fuse
to BS 1362 should always be used, and the fuse cover re-
fitted. If the fuse cover is lost, the plug must not be used
until a replacement is obtained.
GREEN &
YELLOW
13 ampere fuse
BROWN
Replacement fuse covers:
If a replacement fuse cover is fitted, it must be of the correct
colour as indicated by the coloured marking or the colour
that is embossed in words on the base of the plug.
Replacements can be obtained directly from your nearest
Service Depot.
CROSS-BAR
CORD GRIP
BLUE
Removing the plug:
Fig. 10
If your appliance has a non-rewireable moulded plug and
you should wish to re-route the mains cable through
partitions, units etc., please ensure that either:
the plug is replaced by a fused 13 ampere re-wearable plug
bearing the BSI mark of approval.
or:
the mains cable is wired directly into a 13 amp cable outlet,
controlled by a switch, (in compliance with BS 5733) which
is accessible without moving the appliance.
Disposing of the plug:
Ensure that before disposing of the plug itself, you make
the pins unusable so that it cannot be accidentally inserted
into a socket.
Instructions for connecting cable to an alternative plug:
Important: the wires in the mains lead are coloured in
accordance with the following code:
Green &Yellow Earth
Blue
Brown
Neutral
Live
As the colours of the wires in the lead may not correspond
with the coloured markings identifyng the terminals in your
plug, proceed as follows:
Connect Green &Yellow wire to terminal marked E or or
coloured Green or Green &Yellow.
Connect Brown wire to terminal marked L or coloured Red.
Connect Blue wire to terminal marked N or coloured Black.
If a 13 amp plug (BS 1363) is used it must be fitted with a
13 amp fuse, either in the plug or adaptor or at the
distribution board.
If you are in any doubt the electrical supply to your machine,
consult a qualified electrician before use.
GB
10
Technical characteristics
WG 1285W
model
dimensions widthcm 59,5
heightcm 85
depthcm 55
1-5Kg
capacity
electrical voltage 240Volt50Hz
connections maximum absorbedpower2300W
maximum pressure100N/cm 2
minimum pressure5N/cm 2
drum capaciuty42litres
water
connections
upto 1200rpm
Cottonprogram:
spinning
speed
Control
programsin
com pliance TurnknobAtothe"program 2"setting;
with IEC Press energysaverbutton.
regulation
456
ThisapplianceconformswiththefollowingE.E.C.
directives:
-73/23/EEC of19/02/73(Low Voltage)and
subsequentmodifications
-89/336/EEC of03/05/89(Electromagnetic
Compatibility)andsubsequentmodifications
GB
11
GB
12
|