OPERATOR’S MANUAL
PD30R-XXX-XXX-C
INCLUDING: OPERATION, INSTALLATION & MAINTENANCE
PE30R-XXX-XXX-C
RELEASED:
REVISED:
(REV. 07)
2-4-05
11-17-10
3" DIAPHRAGM PUMP
1:1 RATIO (METALLIC)
READ THIS MANUAL CAREFULLY BEFORE INSTALLING,
OPERATING OR SERVICING THIS EQUIPMENT.
It is the responsibility of the employer to place this information in the hands of the operator. Keep for future reference.
SERVICE KITS
Refer to Model Description Chart to match the pump material op-
tions.
637303-XX for fluid section repair (see page 4). NOTE: This kit also
contains several air motor seals which will need to be replaced.
637369 for air section repair (see page 6).
637374-X major air valve assembly (see page 7).
PUMP DATA
Models. . . . . . . . . . . . . . . . . see Model Description Chart for “-XXX”
Pump Type. . . . . . . . . . . . . Metallic Air Operated Double Diaphragm
Material. . . . . . . . . . . . . . . . see Model Description Chart
Weight . . PX30R-XCX-XXX-C . . . . . . . . . . . . 242.3 lbs (109.9 kgs)
PX30R-XSX-XXX-C . . . . . . . . . . . . 253.3 lbs (114.9 kgs)
Maximum Air Inlet Pressure . . . . . . . . . . . 120 p.s.i.g. (8.3 bar)
Maximum Material Inlet Pressure. . . . . . 10 p.s.i.g. (0.69 bar)
Maximum Outlet Pressure . . . . . . . . . . . . . 120 p.s.i.g. (8.3 bar)
Maximum Flow Rate . . . . . . . . . . . . . . . . . . . 237 g.p.m. (897 l.p.m.)
flooded inlet . . . . . . . . . . . 275 g.p.m. (1041 l.p.m.)
Figure 1
MODEL DESCRIPTION CHART
P X 30 R - X X X - X X X - C
Displacement / Cycle @ 100 p.s.i.g. . . . . 2.8 gal. (10.6 lit.)
Maximum Particle Size . . . . . . . . . . . . . . . . 3/8”dia. (9.5 mm)
Maximum Temperature Limits (diaphragm / ball / seat material)
E.P.R. / EPDM . . . . . . . . . . . . . . . . . . . -60° to 280° F (-51° to 138° C)
Hytrel® . . . . . . . . . . . . . . . . . . . . . . . . . -20° to 150° F (-29° to 79° C)
Kynar® PVDF . . . . . . . . . . . . . . . . . . . 10° to 200° F (-12° to 93° C)
Nitrile . . . . . . . . . . . . . . . . . . . . . . . . . . 10° to 180° F (-12° to 82° C)
Polypropylene. . . . . . . . . . . . . . . . . . 35° to 175° F (2° to 66° C)
Santoprene® . . . . . . . . . . . . . . . . . . . -40° to 225° F (-40° to 107° C)
PTFE . . . . . . . . . . . . . . . . . . . . . . . . . . . 40° to 225° F (4° to 107° C)
Viton®. . . . . . . . . . . . . . . . . . . . . . . . . . -40° to 350° F (-40° to 177° C)
Dimensional Data. . . . . . . . . . . . . . . . . . . . . . see page 8
Electronic Interface
D - None
E
-
Available
Air Motor / Air Cap Material
R - Polypropylene / Stainless steel
Fluid Connection
A - 3 - 8 N.P.T.F. - 1
B - Rp 3 (3 - 11 BSP parallel)
Fluid Cap & Manifold Material
C - Cast Iron
S
-
Stainless steel
Mounting Dimensions . . 10-5/32”x 12-1/16”(258 mm x 306 mm)
Hardware Material
Noise Level @ 70 p.s.i., 50 c.p.m. . . . . . . 83.0 db(A)
P - Carbon steel
c
d
S
-
Stainless steel
Tested with 67263 muffler assembly installed.
c
d
Seat Material
A - Santoprene
C - Hytrel
The pump sound pressure levels published here have been updated to
an Equivalent Continuous Sound Level (LAeq) to meet the intent of ANSI
S1.13-1971, CAGI-PNEUROP S5.1 using four microphone locations.
H - Hard 440 stainless steel
K - Kynar PVDF
E
F
-
-
Carbon steel
Aluminum
L
S
-
-
Hastelloy® - C
316 Stainless steel
NOTICE: All possible options are shown in the chart, however, certain
combinations may not be recommended, consult a representative or
the factory if you have questions concerning availability.
G - Nitrile
Ball Material
A - Santoprene
C - Hytrel
T
-
PTFE
V - Viton
G - Nitrile
Diaphragm Material
A - Santoprene
B - Santoprene
C - Hytrel
G - Nitrile
T
-
PTFE / Santoprene
V - Viton
Fluid Section Service Kit Selection
PD30R - XXX - X X X - C
637303 - X X
Example: Model #PD30R-ASS-SAA-C
Fluid Section Service Kit # 637303-AA
Ball
Diaphragm
INGERSOLL RAND COMPANY LTD
209 NORTH MAIN STREET – BRYAN, OHIO 43506
(800) 495-0276 FAX (800) 892-6276
© 2010
y
ꢀ
CCN 15227655
GENERAL DESCRIPTION
MAINTENANCE
The ARO diaphragm pump offers high volume delivery even at low
air pressure and a broad range of material compatibility options are
available. Refer to the model and option chart. ARO pumps feature
stall resistant design, modular air motor / fluid sections.
Air operated double diaphragm pumps utilize a pressure differen-
tial in the air chambers to alternately create suction and a positive
fluid pressure in the fluid chambers, valve checks insure a positive
flow of fluid.
Pump cycling will begin as air pressure is applied and will continue
to pump and keep up with the demand. It will build and maintain
line pressure and will stop cycling once maximum line pressure is
reached (dispensing device closed) and will resume pumping as
needed.
Refer to the part views and descriptions as provided on pages 4
through 7 for parts identification and service kit information.
Certain ARO “Smart Parts” are indicated which should be avail-
able for fast repair and reduction of down time.
Service kits are divided to service two separate diaphragm
pump functions: 1. AIR SECTION, 2. FLUID SECTION. The Fluid
Section is divided further to match typical part Material Op-
tions.
y
y
Provide a clean work surface to protect sensitive internal mov-
ing parts from contamination from dirt and foreign matter dur-
ing service disassembly and reassembly.
y
Keep good records of service activity and include the pump in
preventive maintenance program.
Before disassembling, empty captured material in the outlet
manifold by turning the pump upside down to drain material
from the pump.
y
y
AIR AND LUBE REQUIREMENTS
EXCESSIVE AIR PRESSURE. Can cause pump dam-
WARNING
age, personal injury or property damage.
FLUID SECTION DISASSEMBLY
A filter capable of filtering out particles larger than 50 microns
should be used on the air supply. There is no lubrication re-
quired other than the “O” ring lubricant which is applied during
assembly or repair.
If lubricated air is present, make sure that it is compatible with
the “O”rings and seals in the air motor section of the pump.
y
y
1. Remove (61) outlet manifold and (60) inlet manifold.
2. Remove (22) balls, (19) “O”rings (if applicable) and (21) seats.
3. Remove (15) fluid caps.
NOTE: Only PTFE diaphragm models use a primary diaphragm (7)
and a backup diaphragm (8). Refer to the auxiliary view in the Fluid
Section illustration.
4. Remove the (14) screw, (6) diaphragm washer, (7) or (7 / 8) dia-
phragms, (5) backup washer and (196) cushion.
OPERATING INSTRUCTIONS
NOTE: Do not scratch or mar the surface of (1) diaphragm rod.
Always flush the pump with a solvent compatible with the ma-
terial being pumped if the material being pumped is subject to
“setting up”when not in use for a period of time.
Disconnect the air supply from the pump if it is to be inactive
for a few hours.
The outlet material volume is governed not only by the air sup-
ply, but also by the material supply available at the inlet. The
material supply tubing should not be too small or restrictive.
Be sure not to use hose which might collapse.
When the diaphragm pump is used in a forced-feed (flooded
inlet) situation, it is recommended that a “check valve” be in-
stalled at the air inlet.
Secure the diaphragm pump legs to a suitable surface to insure
against damage by vibration.
y
FLUID SECTION REASSEMBLY
y
y
SERVICE NOTE: ARO pn 204214-T diaphragm assembly tool is rec-
ommended for use when reassembling the pump.
Reassemble in reverse order. Refer to the torque requirements
on page 5.
Clean and inspect all parts. Replace worn or damaged parts
with new parts as required.
Lubricate (1) diaphragm rod and (144) “U”cups with Lubriplate®
FML-2 grease (94276 grease packet is included in service kit).
Be certain the diaphragm assembly bottoms out on the (1) rod,
back off PTFE diaphragm assembly far enough to align holes.
For models with PTFE diaphragms: Item (8) Santoprene dia-
phragm is installed with the side marked “AIR SIDE” towards the
pump center body. Install the (7) PTFE diaphragm with the side
marked “FLUID SIDE”towards the (15) fluid cap.
y
y
y
y
y
y
y
Re-check torque settings after the pump has been re-started
and run a while.
y
Hytrel® and Viton® are registered trademarks of the DuPont Company Loctite® is a registered trademark of Henkel Loctite Corporation Kynar® is a registered trademark of Arkema Inc.
y
y
y
y
Santoprene® is a registered trademark of Monsanto Company, licensed to Advanced Elastomer Systems, L.P. ARO® is a registered trademark of Ingersoll-Rand Company
y
y
y
Lubriplate® is a registered trademark of Lubriplate Division (Fiske Brothers Refining Company) 262™, 271™ and 572™ are trademarks of Henkel Loctite Corporation
y
y
y
Hastelloy® is a registered trademark of Haynes International, Inc.
y
y
PD30R-XXX-XXX-C (en)
Page 3 of 8
PARTS LIST / PX30R-XXX-XXX-C FLUID SECTION
637303-XX Fluid section service kit includes: Balls (see Ball Option, refer to -XX in chart below), Diaphragms (see Diaphragm Option, refer to -XX in chart
below) and items 3, 19, 70, 144, 175, 196 (listed below) and 174 and 94276 Lubriplate FML-2 grease (page 6).
n
SEAT OPTIONS PX30R-XXX-XXX-C
BALL OPTIONS PX30R-XXX-XXX-C
(3-1/4” diameter)
(3/16” x 5” o.d.)
“19”
“21”
“22”
n
n
-XXX Seat
Qty Mtl
(4) [Sp]
-XXX Seat
Qty Mtl
(4) [SH]
-XXX Ball
Qty Mtl “O” Ring
(4) [Sp] 94115
Qty Mtl
-AXX 94104-A
-CXX 94104-C
-EXX 95678
-HXX 94114
-KXX 94621-K
-LXX 94939
-SXX 94113
-XAX 94103-A
-XCX 94103-C
-XGX 94103-G
-XTX 94103-T
-XVX 94103-V
(4)
(4)
(4)
(4)
(4)
[E]
[V]
[B]
[T]
[V]
(4)
(4)
(4)
(4)
[H]
[C]
[A]
[B]
(4)
[K]
(4)
(4)
(4)
(4)
[H] Y327-350
[B] Y325-350
[T] Y328-350
[V] Y327-350
(4) [Ha]
(4) [SS]
-FXX 95674
-GXX 94104-G
NOTE: Seat options -AXX, -CXX and -GXX do not require item 19 "O" ring.
MATERIAL CODE
DIAPHRAGM OPTIONS PX30R-XXX-XXX-C
[A] = Aluminum
[B] = Nitrile
[C] = Carbon Steel
[Co] = Copper
[CI] = Cast Iron
[E] = E.P.R.
[H] = Hytrel
[Ha] = Hastelloy - C
[K] = Kynar PVDF
[SH] = Hard Stainless Steel
[Sp] = Santoprene
[SS] = Stainless Steel
[T] = PTFE
(1/8” x 1” o.d.)
“3”
Service kit
“7”
“8”
n
n
n
n
-XX = (Ball)
-XXX -XX = (Diaphragm)
Diaphragm
Qty
Mtl Diaphragm
Qty
Mtl “O” Ring
- - - Y328-210
- - - Y328-210
- - - Y327-210
- - - Y328-210
[Sp] Y328-210
- - - Y327-210
Qty
(2)
(2)
(2)
(2)
(2)
(2)
Mtl
[T]
[T]
[V]
[T]
[T]
[V]
-XXA 637303-XA
-XXB 637303-XB
-XXC 637303-XC
-XXG 637303-XG
-XXT 637303-XT
-XXV 637303-XV
94091-A
94110-A
94091-C
94091-G
94090-T
95345
(2)
(2)
(2)
(2)
(2)
(2)
[Sp] - - - - -
[Sp] - - - - -
[H] - - - - -
[B] - - - - -
[T] 94110-A
[V] - - - - -
- - -
- - -
- - -
- - -
(2)
[V] = Viton
- - -
MANIFOLD THREAD / FLUID CAP MATERIAL OPTIONS PX30R-XXX-XXX-C
Cast Iron
Stainless Steel
PX30R-ACX-XXX-C PX30R-BCX-XXX-C PX30R-ASX-XXX-C PX20R-BSX-XXX-C
N.P.T.F. BSP N.P.T.F. BSP
Qty Part No. Mtl Part No. Mtl Part No. Mtl Part No.
(size)
Item
Description
Mtl
[SS]
[SS]
[SS]
[SS]
15 Fluid Cap
(2) 94106
[CI] 94106
[CI] 94107
[SS] 94107
32 Leg
(2) 94701-1
(1) 94305-1
(1) 94702-1
[C] 94701-1
[CI] 94305-2
[CI] 94702-2
[C] 94703-2
[CI] 94216-1
[CI] 94704-1
[SS] 94703-2
[SS] 94216-2
[SS] 94704-2
60 Inlet Manifold
61 Outlet Manifold
EXTERNAL HARDWARE OPTION PX30R-XXX-XXX-C
PX30R-XXP-XXX-C PX30R-XXS-XXX-C
(size)
Item
26 Screw
27 Screw
Description
Qty Part No.
(12) 94412-1
(16) 94991-1
(16) 95053-1
Mtl Part No.
[C] 94412-2
[C] 94991
[C] 95053
Mtl
[SS]
[SS]
[SS]
(M12 x 1.75 - 6g x 45 mm)
(M12 x 1.75 - 6g x 60 mm)
(M12 x 1.75 - 6h)
29 Nut
COMMON PARTS
(size)
(size)
Item
Description
Rod
Qty Part No.
(1) 94984
Mtl
[C]
Item
Description
Qty Part No.
(1) Y17-50-S
(2) Y17-51-S
(4) 96656
Mtl
[SS]
[SS]
[SS]
[B]
(1/8 - 27 N.P.T. x 0.27”)
(1/4 - 18 N.P.T. x 7/16”)
126 Pipe Plug
1
5
6
9
76 Pipe Plug
q
p
Backup Washer
(2) 94831-2
(2) 94803
[SS]
[SS]
[SS]
[SS]
[SS]
[SS]
[B]
(M10 x 1.5 - 6g x 120 mm)
Fluid Side Washer
131 Screw
(3/16” i.d. x 2” o.d. x 5/32”)
(3/16” x 1-3/8” o.d.)
Washer
(2) Y13-12-T
(2) Y5-134-T
(1) 94031-1
(1) 94031-2
(2) 94100
144 “U” Cup
175 “O” Ring
(2) Y186-51
(2) Y325-117
(4) 94098
no
no
o
(3/4” - 16 x 3-1/4”)
(3/32” x 1” o.d.)
14 Cap Screw
68 Air Cap
69 Air Cap
70 Gasket
[B]
(0.406” i.d. x 0.031” thick)
180 Gasket
181 Roll Pin
[Co]
(5/32” o.d. x 3/4” long)
(4) Y178-56-S [SS]
(2) 94631 [Sp]
196 Cushion
no
n
Air motor kit parts, see pages 6 and 7.
o
p
q
Used with models PE30R-XXX-XXX-C only.
“Smart Parts“, keep these items on hand in addition to the service kits for fast
repair and reduction of down time.
Page 4 of 8
PD30R-XXX-XXX-C (en)
PARTS LIST / PX30R-XXX-XXX-C FLUID SECTION
COLOR CODE
Diaphragm
Ball
3
2
1
4
Material
Color
Color
Hytrel
Nitrile
Santoprene
Santoprene
(backup)
PTFE
Cream
Black
Tan
Cream
Red (•)
Tan
5
7
8
6
Green
N / A
White
White
Viton
Yellow (-) Yellow (•)
61
(-) Stripe
(•) Dot
FOR THE AIR MO-
TOR SECTION, SEE
PAGES 6 & 7.
26 ꢀꢁ
Torque Sequence
68 181
175
ꢂ
70
ꢂ
76
ꢄ
175
ꢂ
70
ꢂ
1
5
196
7
6
14 ꢀꢆ
22
21
19 ꢂꢃ
27 ꢀꢁ
ꢄ
126
144
ꢂ
ꢂ
144
15
29
ꢁ
69
180
131 ꢀꢅ
ꢂ
3
9
60
22
26 ꢀꢁ
19 ꢂꢃ
21
32
Figure 2
ASSEMBLY TORQUE REQUIREMENTS
NOTE: DO NOT OVERTIGHTEN FASTENERS.
ALL FASTENERS ARE METRIC.
)
(
View for PX30R-XXX-XXT-C (PTFE diaphragm) con-
figuration only.
(14) cap screw, 65 - 70 ft lbs (88.1 - 94.9 Nm).
(26) screw, 60 - 70 ft lbs (81.3 - 94.9 Nm).
(27) screw, 60 - 70 ft lbs (88.1 - 94.9 Nm).
(131) screw, 35 - 40 ft lbs (47.5 - 54.2 Nm).
LUBRICATION / SEALANTS
Apply Lubriplate FML-2 grease to all “O” rings, “U” cups and mating parts.
Apply Loctite® 271™ to threads.
c
d
e
Apply anti-seize compound to threads and bolt and nut flange heads
which contact pump case when using stainless steel fasteners.
Apply Loctite 262™ to threads at assembly.
f
g
h
i
Apply PTFE tape to threads.
Apply Loctite 572™ to threads.
(Santoprene)
(PTFE)
8
Not used with PX30R-XXX-AXX-C, -CXX and -GXX.
Note: Lubriplate FML-2 is a white food grade petroleum grease.
7
PD30R-XXX-XXX-C (en)
Page 5 of 8
PARTS LIST / PX30R-XXX-XXX-C AIR MOTOR SECTION
Indicates parts included in 637369 air section service kit shown below and items (70), (144), (175) and (180) shown on page 4.
AIR MOTOR PARTS
o
(size)
(size)
Item
Description
Qty Part No.
(1) 95667
(1) 94092
(4) 95921
(2) 95846
(1) 95651
(2) 94083
(2) 94084
(1) 94860
(1) 94099
(8) 95931
(8) 95923
(1) 95789
(1) 95789-1
(1) 95790
(1) Y325-32
(1) 95966
(1) Y186-50
(1) 95650
(1) 95659
(1) 94026
(1) 67164
Mtl
[P]
Item
168 "O” Ring
169 “U” Cup
Description
Qty Part No.
(2) 94433
Mtl
[U]
[B]
(3/32” x 5/8” o.d.)
(1/8” x 7/8” o.d.)
101 Center Body
103 Bushing
[D]
(1) Y240-9
(1) 94081
(M6 x 1 - 6g x 180 mm)
105 Screw
[SS]
[SS]
[D]
170 Piston Sleeve
[Br]
[B]
(3/32” x 1-1/8” o.d.)
107 End Plate
111 Spool
171 “O” Ring
172 “O” Ring
173 “O” Ring
174 “O” Ring
(1) Y325-119
(1) Y325-22
(2) Y325-26
(2) Y325-202
(2) 94102
o
o
(1/16” x 1-1/8” o.d.)
(1/16” x 1-3/8” o.d.)
(1/8” x 1/2” o.d.)
(check valve)
[B]
(0.250” x 2.276” long)
(1-1/2 - 11-1/2 N.P.T.)
118 Actuator Pin
121 Sleeve
[SS]
[D]
[B]
o
[B]
no
o
127 90° St. Elbow
132 Gasket
[C / I]
[B]
176 Diaphragm
199 Track Gasket
200 Gasket
[Sp]
[B]
(1) 95666
o
o
(M6)
133 Washer
[SS]
[SS]
[P]
(1) 95665
[B]
o
(M6 x 1 - 6g x 35 mm)
(includes item 127)
134 Screw
201 Muffler Kit
(1) 67213
(PD30R-XXX-XXX-C)
(PE30R-XXX-XXX-C)
(1/8” x 1/2” o.d.)
Valve Block
232 “O” Ring
(2) Y325-202
(1) 95761
[B]
[P]
135
o
[P]
233 Adapter Plate
(M6 x 1 - 6h)
136 End Cap
137 “O” Ring
138 “U” Cup
139 “U” Cup
[P]
236 Nut
(4) 95924
[SS]
[B]
(1/16” x 2” o.d.)
(1/8” x 5/8” o.d.)
[B]
243 “O” Ring
244 “O” Ring
(1) Y325-204
(1) Y325-208
o
o
o
o
o
(3/16” x 1.792” o.d.)
(3/16” x 1-1/4” o.d.)
(1/8” x 7/8” o.d.)
[B]
[B]
[B]
140 Valve Insert
141 Valve Plate
166 Track Gasket
167 Pilot Piston
(Ck)
(Ck)
[B]
Lubriplate FML-2 grease
(1) 94276
637308
n o
Lubriplate Grease Packets (10)
o
o
Items included in fluid section service kit, see pages 4 and 5.
n
(includes 168 and 169)
[D]
MATERIAL CODE
3. Install new (168) “O”rings and (169) seal - Note the lip direction.
Lubricate and replace (167) pilot piston.
[B] = Nitrile
[Br] = Brass
[C] = Carbon Steel
[Ck] = Ceramic
[D] = Acetal
[I] = Iron
[P] = Polypropylene
[Sp] = Santoprene
[SS] = Stainless Steel
[U] = Polyurethane
4. Reassemble remaining parts. Replace (173 and 174) “O”rings.
MAJOR VALVE DISASSEMBLY
1. Remove (135) valve block and (233) adapter plate, exposing
(132 and 166) gaskets, (232) “O”ring and (176) checks.
2. Remove (233) adapter plate, releasing (140) valve insert, (141)
valve plate, (199 and 200) gaskets and (232, 243 and 244) “O”
rings.
AIR MOTOR SECTION SERVICE
Service is divided into two parts - 1. Pilot Valve, 2. Major Valve.
GENERAL REASSEMBLY NOTES:
Air Motor Section service is continued from Fluid Section repair.
y
Inspect and replace old parts with new parts as necessary. Look
3. Remove (136) end cap and (137) “O”ring, releasing (111) spool.
y
for deep scratches on metallic surfaces, and nicks or cuts in “O”
rings.
MAJOR VALVE REASSEMBLY
Take precautions to prevent cutting “O”rings upon installation.
Lubricate “O”rings with Lubriplate FML-2 grease.
Do not over-tighten fasteners. Refer to torque specification
block on view.
Re-torque fasteners following restart.
SERVICE TOOLS - To aid in the installation of (168) “O”rings onto
the (167) pilot piston, use tool # 204130-T, available from ARO.
y
y
y
1. Install new (138 and 139) “U” cups on (111) spool - LIPS MUST
FACE EACH OTHER.
2. Insert (111) spool into (135) valve block.
3. Install (137) “O” ring on (136) end cap and assemble end cap
to (135) valve block, securing with (107) end plates and (105)
screws.
y
y
4. Install (140) valve insert and (141) valve plate into (135) valve
block. NOTE: Assemble (140) valve insert with “dished” side
toward (141) valve plate. Assemble (141) valve plate with 2
identification dots toward (199 and 200) gaskets.
5. Assemble (232, 243 and 244) “O” rings, (199 and 200) gaskets
and (233) adapter plate to (135) valve block.
PILOT VALVE DISASSEMBLY
1. A light tap on (118) actuator pin should expose the opposite
(121) sleeve, (167) pilot piston and other parts.
2. Remove (170) sleeve. Inspect inner bore of sleeve for damage.
6. Assemble (132 and 166) gaskets, (176) checks and (232) “O”ring
to (101) center body.
7. Assemble (135) valve block and components to (101) center
body, securing with (134) screws.
PILOT VALVE REASSEMBLY
1. Clean and lubricate parts not being replaced from service kit.
2. Install new (171 and 172) “O”rings. Replace (170) sleeve.
Page 6 of 8
PD30R-XXX-XXX-C (en)
PARTS LIST / PX30R-XXX-XXX-C AIR MOTOR SECTION
PILOT VALVE
PART GROUP
118
ꢂ
169 168
ꢂ
172
ꢂ
ꢂ
ꢂ
174
121
173
167
171ꢂ
170
173
121
118
174
ꢂ
ꢂ
140 199
ꢂ
244
ꢂ
243
ꢂ
132
ꢂ
166
ꢂ
107
105
135
103
101
133
134
141
ꢂ
232
ꢂ
233
232
ꢂ
176
ꢂ
ꢂ
200
138
ꢂ
Optional 94117 Muffler
111
139
137
136
107
236
ꢂ
ꢂ
201
127
MAJOR VALVE
Figure 3
ASSEMBLY TORQUE REQUIREMENTS
NOTE: DO NOT OVERTIGHTEN FASTENERS.
ALL FASTENERS ARE METRIC.
)
(
(105) screw, 35 - 40 in. lbs (4.0 - 4.5 Nm).
(134) screw, 35 - 40 in. lbs (4.0 - 4.5 Nm).
LUBRICATION / SEALANTS
Apply Lubriplate FML-2 grease to all “O” rings, “U” cups and
mating parts.
c
A replacement major valve service assembly is available separately, which includes the following:
637374 for models PD30R-XXX-XXX-C: 105 (4), 107 (2), 111, 132, 135, 136, 137, 138, 139, 140, 141, 166, 176 (2), 199, 200, 232 (2), 233, 236 (4), 243 and 244.
637374-1 for models PE30R-XXX-XXX-C: 76, 105 (4), 107 (2), 111, 132, 135, 136, 137, 138, 139, 140, 141, 166, 176 (2), 199, 200, 232 (2), 233, 236 (4), 243
and 244.
PD30R-XXX-XXX-C (en)
Page 7 of 8
TROUBLE SHOOTING
Product discharged from exhaust outlet.
Low output volume, erratic flow or no flow.
Check for diaphragm rupture.
Check air supply.
y
y
y
y
y
y
y
Check tightness of (14) cap screw.
Check for plugged outlet hose.
Check for kinked (restrictive) outlet material hose.
Check for kinked (restrictive) or collapsed inlet material hose.
Check for pump cavitation - suction pipe should be sized at
least as large as the inlet thread diameter of the pump for
proper flow if high viscosity fluids are being pumped. Suction
hose must be a non-collapsing type, capable of pulling a high
volume.
Air bubbles in product discharge.
Check connections of suction plumbing.
Check “O”rings between intake manifold and fluid caps.
Check tightness of (14) cap screw.
y
y
y
Motor blows air or stalls.
Check (176) check valve for damage or wear.
Check for restrictions in valve / exhaust.
Check all joints on the inlet manifolds and suction connections.
These must be air tight.
Inspect the pump for solid objects lodged in the diaphragm
chamber or the seat area.
y
y
y
y
DIMENSIONAL DATA
Dimensions shown are for reference only, they are displayed in inches and millimeters (mm).
3 - 8 N.P.T.F. - 1 (PX30R-AXX-XXX-C)
Rp 3 (3 - 11 BSP parallel) (PX30R-BXX-XXX-C)
E
F
A
L
Outlet
B
G
Air Inlet Ports
3/4 - 14 N.P.T.F. - 1
N
D o t t e d l i n e s s h o w
optional 67263 muffler
assembly.
D
Inlet
K
H
C
J
Exhaust Port 1-1/2 - 11-1/2 N.P.T.
DIMENSIONS
M
Figure 4
A - see below
F
- 15”(381.0 mm)
K - 9/16” (14.3 mm)
L - 2-3/4” (69.9 mm)
M - 23-3/32” (586.3 mm)
N - see below
B - 30”(762.0 mm)
C - 12-1/16”(306.4 mm)
D - see below
G - 32” (812.8 mm)
H - 10-5/32” (258.0 mm)
J
- 11-11/16”(296.9 mm)
E
- 17-11/16”(449.2 mm)
“A”
“D”
“N”
PX30R-XCX-XXX-C
PX30R-XSX-XXX-C
23-5/8”(600.1 mm)
23-1/8”(587.4 mm)
2-7/16”(61.9 mm)
2-3/4”(69.9 mm)
15-1/2”(393.7 mm)
16”(406.4 mm)
PN 97999-1111
Page 8 of 8
PD30R-XXX-XXX-C (en)
|