CALLER ID HANDSFREE
HEADSET BUSINESS
TELEPHONE
MODEL IQ750
OPERATING INSTRUCTIONS
6. MEMORY OPERATION ................................................. 22
MEMORYSTORAGE.............................................................................................................................. 22
DIRECTACCESS MEMORY KEYS........................................................................................................ 22
DIRECTORYMEMORY .......................................................................................................................... 26
LASTNUMBER REDIAL MEMORY ........................................................................................................ 27
7. USING THE CALLER ID DISPLAY................................ 29
CALL WAITINGDISPLAY ...................................................................................................................... 30
CALLER LIST ......................................................................................................................................... 30
8. ADVANCED NETWORK OPERATION .......................... 34
PAUSE FUNCTIONWHENDIALINGOUT ............................................................................................... 35
AUTOMATICTRUNKACCESSDIGITINSERTION ................................................................................. 35
AUTOMATICPAUSEINSERTION ........................................................................................................... 35
PAUSETIME ........................................................................................................................................... 36
HOLDINGANDTRANSFERRINGCALLS ..............................................................................................37
USINGTHEMEMORIES .......................................................................................................................... 37
9. INSTALLATION.............................................................. 38
GENERALSETTING-UP ......................................................................................................................... 38
LINECONNECTION ................................................................................................................................38
LOCATION .............................................................................................................................................. 38
WALL MOUNTING .................................................................................................................................. 38
TECHNICALADJUSTMENTS - FOR CORRECTOPERATION ..............................................................41
RECALLTIMINGSELECTION ................................................................................................................. 41
MESSAGEWAITINGLIGHTCOMPATIBILITY .......................................................................................41
HEADSETMICADJUSTCONTROL ....................................................................................................... 41
TO MAKE AHEADSET MIC LEVELADJUSTMENT .............................................................................. 42
HEADSET POLARITY SWITCH ............................................................................................................. 43
10. GENERAL CARE AND MAINTENANCE ..................... 45
CLEANING .............................................................................................................................................. 45
FAILURETOOPERATEANDSERVICEDIFFICULTIES ......................................................................... 45
11. THUNDERSTORMS .................................................... 46
12. WARRANTY - 6 YEARS ............................................... 46
13. SERVICE AND PRODUCT SERVICES....................... 47
3
ILLUSTRATIONS:
FIGURE 1A DATE SETTING ........................................................................................................................................ 9
FIGURE 1B HOUR MODE SETTING ........................................................................................................................... 9
FIGURE 1C AM/PM SETTING ................................................................................................................................... 10
FIGURE 1D TIME SETTING ....................................................................................................................................... 10
FIGURE 2A: TOP VIEW ............................................................................................................................................... 11
FIGURE 2B: BOTTOM VIEW ...................................................................................................................................... 11
FIGURE 3A DISPLAY IN IDLE STATE ...................................................................................................................... 16
FIGURE 3B TYPICAL DISPLAY APPEARANCE WHEN SHOWING DETAILS OF A CALL ................................. 16
FIGURE 4 MEMORY PROTECTION SWITCH ........................................................................................................ 25
FIGURE 5 DISPLAY OF A TYPICAL CALL FROM THE CALLER LIST ................................................................ 31
FIGURE 6A : WALL MOUNTING .............................................................................................................................. 39
FIGURE 6B : IQ235 WALL MOUNT BRACKET. 7626 MODULAR WALL JACK AND LINK CORD................... 39
FIGURE 7: IQ235 WALL MOUNT BRACKET - BREAK-OFF LUGS ...................................................................... 40
FIGURE 8 HEADSET MIC ADJUST CONTROL AND POLARITY SWITCH .......................................................... 43
4
1. FEATURES
"Headset Savvy" Features
•
•
•
•
•
•
•
Auto Detect circuitry disables Handsfree when Headset is in use
Mute Key for Headset microphone
Earpiece Volume Control
Built-in Headset Amplifier suits a wide range of Headset types
Headset Mic Adjustment allows any Headset mic type
Headset Cable Polarity Switch suits any Headset cord
"Silent Ringing" mode selectable so that incoming calls ring only in the Headset to
reduce office noise
•
•
•
•
Trainee/Supervisor "Double Jacking" mode
Change between Headset, Handsfree and Handset modes during a call
Built-in Acoustic Shock Protection
Compatible with “Talking Text” SMS services
Caller ID (CLI) Features
•
•
•
Compatible to Bellcore GR-30-CORE Caller ID standard
Supports Type 2 Caller ID Call Waiting (CIDCW) during a call
SupportsTelstra’s Flashing Message Indicator for MessageBank and Home Messages
101
•
•
•
•
•
•
•
Large Liquid Crystal 3-line Display
Receives and Displays caller's name and number
Saves 80 callers' names (16 characters) and numbers (32 digits)
Date/Time stamp of each call in 24-hour format
New Call, Repeat Call indication
Answered/Unanswered indication of incoming calls in Caller List
Delete a single call or all information from the Caller List, Directory and Redial
Memories
•
•
Blinking Caller LED indicates a new incoming call and/or Message Waiting
On-screen Message Waiting indicator compatible with Nortel DMS system and/or
Centrex Message Waiting
5
General Functions
•
•
•
•
Alpha-numeric keypad
Direct Redial allows immediate redialing of the last number without hanging up
Redial any of the last 5 dialed numbers
20 Direct Access Memories, 10 One-Touch and 10 Two-Touch accessible via 10
keys; capacity 32 number digits and 16 name characters
•
•
•
•
•
80 Caller List memories; capacity 32 number digits and 16 name characters
100 Directory Memories; capacity 32 number digits and 16 name characters
Date and Time Display
Timer for call duration monitoring or stop watch
User selectable Timed-break Recall: 100ms, 200ms, 300ms and 600ms. Factory
set to 100ms
•
•
•
•
•
User selectable Pause timings of 100ms and 1 second. Factory set to 1 second
Manual and storable pause
User selectable High/Low/Off Ringer Volume Control
User adjustable Ringer Pitch Control
Visual ringer indication with high voltage message waiting and BP250 Message
Waiting built-in (see Caller ID section for details of Centrex Message Waiting)
Mute Key with LED visual indicator
•
•
•
•
•
Handsfree/Headset Key with LED indicator
Switch between Handsfree, Headset and Handset modes mid-call
Volume control (Handset and Headset earpieces and Handsfree Speaker)
The Caller List, Directory and Direct Access memories are non-volatile (no batteries
needed)
•
EEPROM Memory allows mass pre-programming of the upper row of 5 Direct
Access memory keys (i.e. 10 memories) to create network feature access keys
Desk or Wall mountable
•
•
On-screen warning icons to indicate “Low Battery” and “Adaptor Failure” power
conditions
6
Operating Requirements
•
•
•
Any 2-wire analog line; if the IQ750’s Caller IDfeature is required, please ensure that
your line delivers the necessary Caller ID data
240V mains outlet for 9V mains power adaptor (supplied) for full support of all
functions
If 4 x AA Alkaline batteries (not supplied) are fitted in the absence of mains adaptor
or during mains power failure, they can provide up to one month's support of all
functions
•
•
If no adaptor or battery power available - basic telephone operation (will automatically
power up approximately 1 second after lifting handset)
Memory backup - no batteries required. All memories (except the Redial memory)
are non-volatile; their contents will be retained without any power
Liquid Crystal Display
•
Liquid Crystal Display with a row of useful icon indicators, a number field and a
name field (16 characters each)
Message Waiting
The following types are supported:
•
•
PABX compatible to 80VDC signal with red LED indicator
-some systems require the fitting of optional circuitry
Polarity reversal (eg. Ericsson BP250) Message Waiting light built-in with red LED
indicator
•
•
•
Centrex (eg. Telstra Spectrum andNortelDMS) with both on-screen and LEDindicators
Type 2 Caller ID Call Waiting (CIDCW) during a call
Telstra’s Flashing Message Indicator for MessageBank and Home Messages 101
7
2. SETTING UP
UNPACKING
The carton contains the following:
• Telephone body and handpiece
• Coiled Handset cord and line cord
• 9V DC Adaptor
• Quick Start-up Guide
GENERAL SETTING-UP
1. Fit the Coiled Cord to the appropriate sockets in the Handset and in the telephone
base - please do not connect the coiled cord into the Headset jack
2. Fit the Line Cord to the rear socket and to your telephone network outlet
3. Set the Ringer Volume and the Ringer Pitch controls
4. Lift the handset to check for dial tone and to wake up the DISPLAY
5. If using a Headset, connect it to the Headset jack (See Figure 2B)
6. Fit the Adaptor Plug to the 9VDC Jack and plug in the Adaptor to a mains power
outlet
7. Follow the instructions below for general installation
8. See section 9 for other installation instructions and technical settings.
LINE CONNECTION
This telephone is supplied with an RJ45 Plug as the wall plug, with the centre pair being
reserved for speech and signalling. Other types of plugs and cords are available on request.
DISPLAY BRIGHTNESS ADJUSTMENT
With the telephone on-hook and in an idle state, press Cursor and to alter the display
to achieve the best contrast for your lighting conditions.
8
DATE AND TIME SET UP DISPLAY
The best time to set up the Date and Time is during installation, as follows:
Upon installation the display will automatically show step by step prompts to guide you
through theDate and Time setup procedure. This procedure can also be used at any time
to change the time and date settings.
The following procedure assumes that all steps in the “General Setting Up” have been
carried out.
NEW
TIMER
AM
REPEAT
CALL#
PM
FIGURE 1A DATE SETTING
1. If the display is blank, lift the Handset briefly to wake up the telephone and replace
the Handset in the cradle
2. For 10 seconds the display will show “20040101” and “DATE-YYYYMMDD” when
the unit is first powered up
3. If the display is alive but not showing “20040101” and “DATE-YYYYMMDD”, press
STORE, TIMER; the display will return to the “20040101” and
“DATE-YYYYMMDD” mode. Proceed to step 4 within the next 10 seconds; repeat
step 3 if necessary to re-enter Date/Time setting mode.
4. Enter Year (4 digits), Month (2 digits) and Date (2 digits)
NEW
TIMER
AM
REPEAT
CALL#
PM
FIGURE 1B HOUR MODE SETTING
5. Hour Mode Setting - the display will now show “1-12HR 2-24HR”
6. Press 1 for 12 hour mode or 2 for 24 hour mode display (if 24 hour mode was
chosen, please go to step 9)
9
NEW
TIMER
AM
REPEAT
CALL#
PM
FIGURE 1C AM/PM SETTING
7. If 12-hour mode was selected above, the display will show “1-AM 2-PM”
8. Press 1 or 2 to select AM or PM time display
NEW
TIMER
AM
REPEAT
CALL#
PM
FIGURE 1D TIME SETTING
9. The display will show “TIME-HHMM” after completion of the Hour Mode Setting
10. To set the current time enter 2 digits for the hour, followed by two digits for the
minutes
11. The display will show “CLOCK STORED” and the date and time will be updated.
Note: use Cursor or to correct your numeric entries stage in the above procedure.
BASIC OPERATION
IQ750 can be used in the same way as a normal telephone; simply lift the Handset to
answer an incoming call, or lift the Handset and dial on the Keypad to commence an
outgoing call. Please refer to other sections for more about Handsfree, Headset, Caller ID
display and Memory operations. The telephone will also operate in a basic mode when
mains power has failed and if batteries have not been fitted (the telephone will
automatically power up approximately 1 second after lifting handset). If 4 x AA alkaline
batteries (not supplied) are fitted in the absence of mains adaptor or during mains power
failure, they can provide up to one month's support of all functions.
10
3. GENERAL CONTROLS AND INDICATORS
DISPLAY
STORE KEY
RINGER/MESSAGE WAITING INDICATOR
DIRECT ACCESS
MEMORY KEYS
CURSOR KEYS ( AND
)
CLEAR KEY
TIMER KEY
RESET KEY
MEMORY PROTECTION SWITCH
DIRECTORY KEY
CALLER KEY WITH NEW CALL INDICATOR AND
CENTREX MESSAGE WAITING INDICATOR
SCROLL KEY ( AND
)
DIAL KEY
RECALL KEY
HANDSFREE/HEADSET KEY AND INDICATOR
MUTE KEY AND INDICATOR
REDIAL KEY
PAUSE KEY
FIGURE 2A: TOP VIEW
HEADSET JACK LINE JACK
9V ADAPTOR JACK
RINGER PITCH
CONTROL
RINGER VOLUME
SWITCH
MOUNTING HOLES FOR
IQ235 WALL BRACKET
HEADSET POLARITY
SWITCH
Reversed headset
polarity
Normal headset
polarity
HANDSET JACK
VOLUME SLIDER
BATTERY COMPARTMENT
(OPTIONAL BATTERIES NOT
SUPPLIED)
HEADSET MIC
ADJUSTMENT CONTROL
FIGURE 2B: BOTTOM VIEW
11
RINGER/MESSAGE WAITING INDICATOR
Located at the top right hand side of the telephone above the DISPLAY, the red lense
contains two different indicators; their functions are as follows:
1. Ring Indicator
Flashes when the telephone rings with an
incoming call.
2. PABX Message Waiting Indicator Illuminates when a message is waiting in your
PABX voicemail system (depends on system
compatibility). The built-in Message Waiting
option suits any neon type (minimum 80 VDC)
message waiting system and Ericsson BP250
Message Waiting (other system types are available
as optional extras). To determine which PABX type
your IQ750 has been prepared to suit,
check the telephone’s underside for a label indicating that specific circuitry has been
installed in your unit. If in doubt, contact Interquartz for further details. To retrieve your
message, consult your voice mail system user guide.
IQ750 is also fitted with a message waiting indicator lamp which is compatible with the
voicemailfeaturesofCentrexnetworks(eg.TelstraCustomnet)andresidentiallinevoicemail
systems (eg. Telstra Home Messages 101 and MessageBank). There are indicators
located in the CALLER Key and display for these services and are described elsewhere
in this manual.
RINGER VOLUME SWITCH
The three available positions allow selection of OFF (no sound), LOW volume, and HIGH
volume of the telephone ringing sound during an incoming call (Figure 2B).
RINGER PITCH CONTROL
The pitch of the ringing sound may be altered by rotating the control to suit your preference
to achieve a distinctive sound, or one that is audible, more distinctive or more pleasant.
12
ALPHA-NUMERIC KEYPAD
In addition to normal dialling, the alphabetic characters are provided on the keys to enter
names in the Direct Access and Directory memories as well as any online applications
that require alphabetic keystrokes.
RESET KEY
Press to restore normal operation of the telephone in case of a malfunction or lock-up.
The memories will not be erased when this key is pressed.
CRADLE SWITCH
Located in the handset cradle, this plastic lever is depressed by the Handset (when
placed in the cradle) to cut off the line. Note: Depressing this cradle lever too briefly when
intending to terminate a call may result in an accidental “hookflash” that will inadvertently
place the call on hold - this is known as “phantom calls” because the held call may ring
again at your extension within a few minutes (the other party will have hung up, so it will
seem as if you were called by a phantom, hence the name “phantom calls”). If you
experience this problem, when terminating your call please depress the cradle lever a
little longer before making/receiving your next call (i.e. phantom calls are not a system
or telephone fault).
VOLUME SLIDER
Used to adjust the hearing level of the Handset Earpiece/Handsfree Speaker/Headset.
Set to midway for normal listening level. Adjustment during a conversation will not be
detected by the other party.
RECALL KEY
For use with PABX systems to invoke special PABX facilities such as call-hold or call
transfer which may be available in your PABX. It is sometimes referred to as the “Flash”
Key or “Facility” Key. To learn how to use it, please consult your telephone host system
manual. Recall timing is preset to 100mS. The Recall Timing setting affects the Recall
Key’s ability to function correctly with your system (see the Installation section regarding
this setting).
13
REDIAL KEY
Press to redial the last number last dialed, which may be up to 32 digits long. When
pressed while still on-line, the telephone will clear the call and retry the number. It can be
used in Handset, Handsfree, and Headset modes. Dialing more than 32 digits during one
call will cause erasure of the entire number from the Redial Memory.
See further details of the 5-stack Last Number Redial Memory in section 6 “Memory
Operation”.
To redial last number
1. Lift Handset, or press HANDSFREE/HEADSET
2. Press REDIAL (telephone redials last number).
To direct redial the last number
1. Lift Handset, or press HANDSFREE/HEADSET
2. Dial a number, [unsuccessful]
3. Press REDIAL; the telephone will automatically clear and re-connect the line; the
number will be re-dialed.
PAUSE FUNCTION
The Pause command may be needed if your phone is connected to certain types of
PABX or to any network where a momentary pause is required (e.g. between internal and
external dial tones).
For manual dialing:
1. Lift Handset
2. Dial any digits required before the pause
3. Press PAUSE; the telephone will complete the dialing process once the Pause
time has elapsed
4. Dial the remaining digits.
The Pause function can be stored in any Direct Access or Direct Memories. See section
8 for further details.
MUTE KEY AND INDICATOR
When pressed, it cuts off transmission from the Handset, Headset and Handsfree
microphones to allow user privacy. The red light indicates when the mute condition is
active. Press MUTE again to release the mute condition.
14
HANDSFREE/HEADSET KEY AND INDICATOR
The HANDSFREE/HEADSET Key has an auto-detection function; which disables the
Handsfree mode when a Headset is in use. When the HANDSFREE/HEADSET Key is
pressed, a red indicator will glow to show that the Handsfree or Headset mode is activated.
Press the key again to turn it off.
To use Handsfree mode
Ensure that a headset is NOT connected to the Headset Jack. Press the HANDSFREE/
HEADSETKey; the telephone will automatically operate in Handsfree Mode.Ared indicator
will glow to show that the Handsfree mode is activated. Press the key again to turn it off.
To use Headset mode
Connect a headset to the Headset Jack. Press the HANDSFREE/HEADSET Key; the
telephone will automatically operate in Headset Mode. A red indicator will glow to show
that the Headset mode is activated. Press the key again to turn it off.
CURSOR
AND KEYS
The Cursor and Keys serve as display brightness adjustment keys in normal mode.
They serve as Edit Keys during Memory Storage.
TIMER KEY AND AUTOMATIC CALL TIMER FUNCTION
When a call is in progress, the word TIMER appears on the DISPLAY, and the time will
count from 00:00. The call duration will be displayed for 10 seconds after the call is
terminated.
To use the timer function as a stop watch when the telephone is idle (not in use on a call)
1. Press TIMER once to view the last timer value
2. Press TIMER again to start the timer; the timer will count up from 00:00 to 59:59
and then roll over to 00:00 again
3. Press TIMER once more to stop the timer; the display will show the timer value
for 10 seconds
4. Press TIMER again to resume the clock display in less than 10 seconds if required.
To use the timer as a call timer, the telephone will automatically enter the Timer mode
when commencing a call. After hanging up, the timer will stop and its value will stay on
the display for 10 seconds.
15
BATTERY COMPARTMENT
As a precaution against the potential for an interruption of mains power to affect the
progress of any ongoing call, 4 x AA alkaline batteries can be fitted to the compartment
(they can provide up to one month’s support of all functions while mains power is absent).
However, while mains power is present, battery power will not be consumed. If batteries
have been fitted, it is recommended that they be routinely replaced before the “best
before” date indicated by the battery manufacturer (consult the packaging or check on
the battery).
DISPLAY ICONS AND FIELDS
Answered/
Centrex Message
Waiting
Clock
Time
Unanswered call
Date
am/pm
Number of
Power Adaptor
Failure
NEW
New Calls or
Repeat Call #
REPEAT
CALL#
Battery Low
Total Call(s)
Counter
New Call(s)
Counter
FIGURE 3A DISPLAY IN IDLE STATE
NEW
TIMER
AM
REPEAT
CALL#
PM
Number field
Name field
FIGURE 3B TYPICAL DISPLAY APPEARANCE WHEN SHOWING DETAILS
OF A CALL
16
Received Call Status indication;
NEW - new calls have been received that have not previously been reviewed
in the Caller List (the Caller Key will also be flashing)
REPEAT - indicates multiple calls have been received from the same caller in
the current Caller List’s history; therefore please note that only the most
recent call from that caller’s number will be retained in the Caller List.
CALL # - entry number in Caller List
Date in Month/Day format; shows current date or date of received call when
reviewing Caller List
Indicates Call Timer or Stop Watch mode is active
For the clock readout and when reviewing the time that a call arrived in the
Caller List (displays only in 12 hour mode)
Hour:Minute format for the clock readout and when reviewing the time that a
call arrived in the Caller List (displays only in 12 hour mode)
Minute:Second format in Timer and Stop Watch modes (maximum count
99:59)
Displays together with “MESSAGE WAITING” text in the name field; to indicate
the presence of message waiting in voicemail system (see “Message Waiting
Light Compatibility” section)
Indicates, when reviewing the Caller List, that the call was answered on the IQ750
Indicates, when reviewing the Caller List, that the call was NOT answered on
the IQ750
If this symbol is visible, the 4xAA Alkaline batteries in the battery compartment
should be replaced
Will be displayed in the absence of the adaptor power (only functions if
batteries are also fitted and are in good condition)
16 digits for displaying telephone number
Number Field
Name Field
16 characters for displaying caller name or number of new calls and
total calls received.
17
4. HANDSFREE OPERATION
To commence a Handsfree call press HANDSFREE/HEADSET; the telephone will activate
the line, and the Speaker, and the Indicator will switch on to provide confirmation. Dialing
and speech can then commence. Pressing the key again will terminate the call. The
Handsfree state is storable in theDirectAccess memory keys – please see the MEMORY
OPERATIONsection.
The Handsfree mode will be disabled if a Headset is connected to the Headset Jack.
Incoming calls using Handsfree:
1. Telephone rings
2. Press HANDSFREE/HEADSET
3. Commence your Handsfree conversation.
Outgoing calls using Handsfree (manual or memory dialing):
1. Press HANDSFREE/HEADSET
2. Dial required number or press desired Memory Key
3. Speak as necessary.
Changing from Handsfree to Handset during a call:
Lift Handset and resume your conversation; the Handsfree function will switch off
automatically.
Changing from Handset to Handsfree during a call:
1. Press HANDSFREE/HEADSET
2. Replace Handset mode
3. Resume your conversation in Handsfree mode.
18
HINTS FOR HANDSFREE OPERATION
As a courtesy, tell the other party that you are using the Handsfree function. He/She
may or may not want people other than you to hear the conversation. Aquiet environment
ensures best Handsfree performance. When Handsfree is used in a noisy room or near a
noise generating device (for example, a TV set), all or part of the message may be
interrupted and cannot be heard. To eliminate this problem, try to lower the noise level in
the room.
During the Handsfree conversation, your telephone will give priority to the person who
speaks louder when both people are talking simultaneously. Speak ONLY after the other
person pauses or stops.
If the other person complains about poor transmission, talk directly at your telephone
and from a closer distance as necessary, or lower volume control.
If the operation of the Handsfree feature is not correct, refer to the FAILURE TO OPERATE
section.
19
5. HEADSET OPERATION
The IQ750 can be configured to suit many different headsets - please consult the
INSTALLATION section for details to get the best performance from your headset.
BASIC OPERATION
To make or receive call using the Headset:
1. Press HANDSFREE/HEADSET
2. If you are making an outgoing call, dial the required number
3. To revert from Headset mode to Handsfree mode during a call from Headset
mode, unplug the Headset
4. Speak as necessary
5. To hang up, press HANDSFREE/HEADSET
HEADSET/HANDSET/HANDSFREE MODES
A call can be switched between modes as follows:
1. To revert to Handset mode from Headset mode, lift Handset
2. To revert back to Headset mode during Handset mode, press
HANDSFREE/HEADSET.
TRAINEE/SUPERVISOR MODE
Allows the Handset and Headset to be used in tandem. This will enable a supervisor to
monitor a trainee’s progress during a call, or “take over” a call. The following procedures
assume that the trainee is wearing the Headset and a call is in progress.
1. During a trainee’s call the supervisor may lift the Handset (Handsfree/Headset indicator
will turn off)
2. Quickly press HANDSFREE/HEADSET and the indicator will illuminate
3. The trainee may continue the conversation with the supervisor only listening to the
call.
20
Silent Ringing
Designed for call centres or any application where call-related noise is to be kept
to a minimum, this feature allows incoming calls to ring silently; the operator is
aware of the incoming call, but the telephone does not add to the room noise even
when ringing.
To use the telephone in Silent Ringing mode:
1.
Set the Ringer Volume Switch to the OFF position (signified by the square
symbol without a bell symbol inside it)
2.
3.
Put your Headset on and wait for the next incoming call
When a call arrives, the Ringer/Message Waiting Indicator will flash and
the operator will hear the ringing tone at a low level in the Headset
4.
Press HANDSFREE/HEADSET to answer the call.
ALERT LIGHT SUPPORT
The IQ750 is designed to support the “Alert Light” available on some Headsets. When
pressing HANDSFREE/HEADSET on the telephone, the “Alert light” indicator on the
Headset will be illuminated, signifying that the user is on a call. This feature can be used
effectively in call centre applications so that the user’s colleagues will be aware that the
user has a call in progress.
21
6. MEMORY OPERATION
MEMORY STORAGE
Model IQ750 has 20 Direct Access Memories, 100 Directory Memories, 80 incoming call
Caller List and 5 Last Number Redial Memories. All memories have a maximum 32 digits
capacity and 16 characters name capacity.
Memory Backup
No batteries are required. The Caller List, Direct Access and Directory Memories are
non-volatile (no batteries needed to retain contents in the event of power failure).
Memory Storage
Storage operations can be carried out either with the adaptor connected or with batteries
installed.
To enter letters for name entries, use the letters marked on the keys. For example, press
key 7 (P, Q, R, S) once to enter P, twice to enter Q and so on. To make a space, press
the right hand ( ) Cursor key.
To commence a storage procedure, lift the Handset or press HANDSFREE/HEADSET
before commencing the procedures described for storing numbers and names as
described below. To delete any incorrect digits while storing, use the Cursor or move to
the unwanted character and press CLEAR.
DIRECT ACCESS MEMORY KEYS
The IQ750 has 20 Direct Access speed-dial memories accessible via 10 keys near the
DISPLAY (see Figure 2A). These keys each have five “One-Touch” memories and five
“Two-Touch” memories. The One-Touch memories are accessed by pressing the key
once briefly during the storage or retrieval procedures described in this manual. The Two-
Touch memories are accessed by pressing the same memory key twice in quick
succession.
The Direct Access memories are very useful for storing some of your favourite network
facility codes (e.g. Diversion, Call Forward, Call Back etc). Consult your system User
Guide for the codes that you need to store to activate these functions.
22
Direct Access Memory Capacity
Each memory can store up to 32 digits plus Pause,
code.
,
Recall (Flash) and a Handsfree
Speed-Dialling (Storable Handsfree code)
When storing a number, you can add a “Handsfree” command to the start of the number.
It appears as an “H” on-screen. This programming technique makes dialling faster and
easier – to commence dialling of anyDirectAccess memory programmed with a “Handsfree”
code the memory key can be pressed without the need to lift the handset or press the
Handsfree/Headset key.
Speed-Dialling and Automatic Hang-up
The Handsfree code may also be stored in a Direct Access memory key at the trailing
end of a stored number to make the telephone hang up immediately after dialling the
number.
Example(where“H”representstheHandsfreecodeand“nnnnn”representsanysubsequent
digits to be dialled)
1. If H is entered as a prefix code:
Stored string: H nnnn
Result: The phone will go on-line in Handsfree mode and dial out the subsequent
number. Phone will remain on-line in handsfree mode until the user manually
hangs up.
2. If H is entered at both ends of the digits to be dialled
Stored string: H nnnnn H
Result: The phone will go on-line in Handsfree, dial out the number and go off line
again.
To store a Number and Name in a Direct Access memory
1. Press STORE; the display will show “STORE”
2. Press the Memory Key either once to store in a One-Touch memory or twice for a
Two-Touch memory; the display will show “ENTER NUMBER”
3. If you wish to setup the chosen memory key as a speed-dial key, go to step 4.
Otherwise go to step 5
23
4. Press HANDSFREE/HEADSET; the DISPLAY will show “H” in the number field. If
this is not required, go to step 5 without pressing HANDSFREE/HEADSET
5. Enter the telephone number and press STORE
6. Enter the name by using the Keypad and press STORE to confirm; the display will
show “MEMORY STORED”.
To dial from a Direct Access Memory
Speed-Dial memory (i.e. the memory key has been programmed with an “H” preceding
the number as described above):
Press the desired Memory Key either once to dial from its One-Touch memory or twice
to dial from its Two-Touch memory.
Non Speed-Dial memory (i.e. the memory key has NOT been programmed with an “H”
preceding the number as described above):
Press the desired Memory Key either once to dial from its One-Touch memory or twice
to dial from its Two-Touch memory.
Direct Access Memories and the Memory Protection Switch
The Memory Protection Switch protects the upper row of five memory keys near the
display to prevent them from being overwritten by the user in daily use. The memory
protect switch is located underneath the lower memory number card (see Figure 4).
it is recommended that the upper row of 5 memory keys (i.e. 10Direct Access Memories)
be programmed to create network features access keys to store some of your favourite
network facility codes (e.g. Diversion, Call Forward, Call Back etc). This will enable more
convenient access to these features without the need to remember the necessary codes.
The memory card paper insert below the memory keys can be used to label the keys to
indicate their new functions (i.e. the name of the network feature). Consult your system
User Guide for the codes that you need to store.
If your upper-row memory keys are locked and prevent storage of new numbers this may
be due to the presence of pre-programmed codes chosen by your system administrator.
Before moving the switch to the “Non-Protected” position we recommend that you contact
your system administrator, Interquartz or your dealer to discuss if they can be unlocked.
Changing the switch setting may allow any pre-programming to be lost.
24
To program or alter the contents of a protected Direct Access memory:
1. Remove the memory card paper insert below the top row of Direct Access memory
keys to reveal the MEMORY PROTECTION SWITCH
2. Move the MEMORYPROTECTIONSWITCH to the “Non-Protected” position asshown
in Figure 4
3. Press STORE; the display will show “STORE”
4. Press the Memory Key either once to store in a One-Touch memory or twice for a
Two-Touch memory; the display will show “ENTER NUMBER”
5. Enter the telephone number and press STORE
6. Enter the name (name of the feature code) by using the Keypad and press STORE
to confirm; the display will show “MEMORY STORED”
7. Move the MEMORY PROTECTION SWITCH to the “Protected” position as shown in
Figure 4
8. Gently press the small RESET key next to the MEMORY PROTECTION SWITCH.
To dial from a Protected Direct Access Memory
Press the desired Memory Key either once to dial from its One-Touch memory or twice
to dial from its Two-Touch memory.
STORE
CLEAR
Non-Protected
Protected
Reset-
DIRECTORY
CALLER
FIGURE 4 MEMORY PROTECTION SWITCH
25
DIRECTORY MEMORY
The Directory Memory works like the memory of a typical mobile phone, with the storage
of names with numbers and name searching capability. The keys on the Keypad allow
the entering of alpha and numeric characters in the name field.
If your network does not send caller name information in conjunction with the caller’s
number, the ability of the IQ750 to display the caller’s name during an incoming call will
be dependent on the caller’s number matching a number already stored in the Directory
Memory. Therefore, at the time of installation it may be useful to store names and
numbers of friends, business associates and other regular callers into theDirectory Memory
to take immediate advantage of the name display feature. In addition, the Caller List can
be used as a convenient source of programming data – the details of any previous incoming
calls found in the Caller List can be stored in the Direct Access memory keys and/or the
Directory memory by a simple transfer process, thereby reducing keystrokes and
eliminating potential error that may otherwise result during manual storage of the same
details. Please see the sections entitled “To store a caller’s details in a Direct Access
Memory from the Caller List” and “To store a caller’s details in theDirectory Memory from
the Caller List” located in the CALLER ID OPERATION section.
Directory Memory Capacity
The Direct Access Memory can store up to 100 names & numbers. When the memory is
full; the display will show “DIRECTORY FULL”.
To Store a Number and Name into a Directory Memory
1. Press STORE; the display will show “STORE”
2. Press DIRECTORY; the display will show “ENTER NUMBER”
3. Enter the telephone number, then press STORE; the display will show “ENTER
NAME”
4. Enter the name by using the Keypad
5. Press STORE; the display will show “DIRECTORY STORED”.
If the telephone number and name being stored match a previous entry, the display will
show “DIRECTORY EXIST” and the new entry will not be stored.
26
To dial from the Directory Memory using Name Search
1. Press DIRECTORY, the first entry in the directory will be displayed
2. Enter the first Alpha Numeric character of the name you wish to dial
3. Use Scroll or to find the name
4. Press DIAL to dial it out.
To edit an entry in the Directory Memory
1. Press DIRECTORY; the first entry in the directory will be displayed
2. Press Scroll or to select the entry you want to edit
3. Press STORE, the first digit of the telephone number will begin to flash
4. Use Cursor or to navigate to the digit(s) to be changed and make the necessary
changes
5. Press STORE to confirm
6. The first letter of the name will flash; use Cursor or to navigate to the letters to
be changed and make the necessary changes
7. Press STORE to confirm; the display will show “DIRECTORY STORED”.
To delete an entry from Directory Memory
1. Press DIRECTORY; the first entry in the directory will be displayed
2. Press Scroll or to select the entry you want to delete
3. Press CLEAR twice briefly, the display will show “ERASED”.
Caution: If CLEAR is pressed continuously for 6 seconds in the above procedure, the
entire directory list may be deleted.
LAST NUMBER REDIAL MEMORY
The LastNumber Redial memory contains your 5 most recently dialled outgoing numbers,
with a maximum of 32 digits each. The Scroll key allows you to navigate through the list
to select the number that you wish to redial.
27
Using the 5-Stack Last Number Redial Memory
1. To dial the most recently dialled number, press REDIAL. If you require an earlier
number go to step 2, otherwise proceed to step 3
2. Press Scroll or to select a number from the 5 redial memories. The most
recently dialled number will be identified as “REDIAL 1” on the display, and the
earliest as “REDIAL 5”.
3. Press DIAL to dial the selected number.
See REDIAL KEY section details of the Direct Redial Function
28
7. USING THE CALLER ID DISPLAY
This section assumes that you are using the IQ750 in a network that is capable of
supplying Caller ID data in the Bellcore GR-30-CORE format. In addition, you may need
to request or subscribe to Caller ID and Call Waiting Services from your network provider
before Caller ID data will be sent by the network. For details, please contact your service
provider.
When an incoming call is received, information including the caller’s name, number, call
date & time will be transmitted to your Caller IDDisplay Telephone between the first and
second rings from the network.
Caller ID during a typical incoming call
1. The Ringer sounds and the Ringer Indicator will flash
2. After about 1 second, the caller’s information is shown on the display
3. If the call is not answered, the caller’s information will be kept on the display for
a further 10 seconds after the last ring; and the Caller Key (New Call) indicator will
flash. The caller’s number can be up to 16 digits long, and the name can be up to 16
characters long before exceeding the capacity of the display
4. The details of the call will be stored in the Caller List.
Displaying the caller’s name during an incoming call
The caller’s name will be automatically displayed if:
a) the name information is delivered by your telephone service in conjunction with the
caller’s number, or
b) if the number matches a number stored in the Direct Access or Directory Memory.
At the time of installation it may be useful to store names and numbers of friends, business
associates and other regular callers into the Directory Memory to take advantage of the
name display feature.
29
In addition, the Caller List can be used as a convenient source of programming data – the
details of any previous incoming calls found in the Caller List can be stored in the Direct
Access memory keys and/or the Directory memory by a simple transfer process, thereby
reducing keystrokes and eliminating potential error that may otherwise result during
manual storage of the same details. Please see the relevant sections entitled “To store
a caller’s details in a Direct Access Memory from the Caller List” and “To store a caller’s
details in the Directory Memory from the Caller List”.
CALL WAITING DISPLAY
The IQ750 can display the details of a current caller while you are already on a call. To
enable the Call Waiting feature, you may need to request or subscribe the Call Waiting
Service from your network provider. For details, please call your service provider.
Note: It is not recommended to use more than two Caller ID phones in parallel on the
same line as their performance may be affected. For example, Caller ID display of a
second call while you are off-hook (i.e. Call Waiting Caller ID, sometimes known as
“Type 2 Caller ID”) may not be received by the IQ750 if another parallel connected Caller
ID phone is in use and off hook in party line fashion on the same call.
CALLER LIST
The IQ750 stores the details of all incoming calls in a Caller List, which is accessible by
pressing the Caller key. The Caller List can store up to 80 caller records, and when it has
reached its full capacity the oldest record will be removed to accommodate the new call.
To view the Caller List and dial a Number in the Caller List
1. Press CALLER to display the most recent incoming call; if there is no entry in the
Caller List, the display will show “NO ENTRIES”
2. Press Scroll to move on to the previous call; subsequent presses will
display successively earlier calls
3. To dial a number displayed; press DIAL
4. If the end of the Caller List is reached, the display will show “END OF LIST”; you
may continue to scroll or to review the list again
5. If you choose not to dial any number from the Caller List, the DISPLAY will revert to
clock mode in 10 seconds.
30
A typical call displayed from the Caller List is depicted in Figure 5.
Date (month:day) of call,
New of Repeat Call
time of call
(only one of these will be on)
NEW
TIMER
AM
REPEAT
CALL#
Entry Number in
the Caller List
PM
Caller’s number
Caller’s name
FIGURE 5 DISPLAY OF A TYPICAL CALL FROM THE CALLER LIST
When reviewing the Caller List, you may see the following details:
“OUT OFAREA” - a caller’s network does not offer the Caller ID service or the call is
from an overseas caller or a payphone.
“PRIVATE”
- a caller has blocked his/her number from being transmitted and
displayed.
“LINE ERROR”
- the telephone cannot recognize the information contained with the
Caller ID message.
NEW - new calls have been received that have not previously been reviewed
in the Caller List
REPEAT - indicates multiple calls have been received from the same caller in
the current Caller List’s history; therefore please note that only the most
recent call from that caller’s number will be retained in the Caller List.
CALL # - entry number in Caller List
31
Date in Month/Day format; shows current date or date of received call when
reviewing Caller List
Timer - indicates Call Timer or Stop Watch mode is active
For the clock readout and when reviewing the time that a call arrived in the
Caller List (displays only in 12 hour mode)
Hour:Minute format for the clock readout and when reviewing the time that a
call arrived in the Caller List (displays only in 12 hour mode)
Indicates, when reviewing the Caller List, that the call was answered on the IQ750,
Indicates, when reviewing the Caller List, that the call was NOT answered on
the IQ750
To store a caller’s details in a Direct Access Memory from the Caller List
1. Press CALLER; the most recent incoming caller’s name and number will be
displayed
2. Press Scroll or to select the number you want to save into the Direct
Access Memory
3. Press STORE; the display will show “STORE”
4. Press a Memory Key (One-Touch or Two-Touch Memory Key); the display
will show “ENTER NUMBER” below the telephone number
5. Press STORE to confirm. You can use Cursor or to change the number before
saving
6. The display will show the caller’s name; press STORE to confirm. You can use
the Cursor or to edit the name before saving
7. The display will show “MEMORY STORED”.
32
To store a caller’s details in the Directory Memory from the Caller List
1. Press CALLER; the most recent incoming caller’s name and number will be
displayed
2. Press Scroll or
Memory
to select the number you want to save into the Directory
3. Press STORE; the display will show “STORE”
4. Press DIRECTORY; and the display will show “ENTER NUMBER” below the
telephone number
5. Press STORE to confirm. You can use the Cursor or to change number before
saving
6. The display will show the caller’s name; use the Cursor or to edit the
name if necessary
7. Press STORE to confirm; the display will show “DIRECTORY STORED”.
To delete a Call from the Caller List or to delete the entire Caller List
1. Press CALLER and press Scroll or to find the entry you wish to delete
2. To erase the displayed call, press CLEAR twice in rapid succession; the display
will show “ERASED”
3. To erase the entire Caller List, press CLEAR twice in rapid succession and hold the
key down on the second depression; the display will show “HOLD TO CLR CALL”
4. To prevent entire directory erasure release the CLEAR key at this time before 6
seconds has elapsed; otherwise keep holding the key down and go to the next step
5. 6 seconds from step 3 the directory will be deleted and the display will show
“CALL MEM CLEAR”.
Note: See MEMORYOPERATION section for more details of storing and dialing operations
using Direct Access and Direct Memories.
33
8. ADVANCED NETWORK OPERATION
Where this telephone is used on an intelligent network such as Easycall, Customnet,
Centel, Spectrum, a PABX or any Centrex Networks, the following information may be
useful.
Message Waiting function in conjunction with Telstra’s Customnet, MessageBank
and Home Messages 101 services
The IQ750 has built-in compatibility with the above services. When the Message Waiting
signal is received:
1. the CALLER key will flash
2. the display will show the words “Message Waiting” in the name field
3. the display will show an envelope icon.
Manually Resetting the Message Waiting Prompts
The message waiting prompts as described above are normally controlled by the network
to switch on and off as needed. If at any stage the telephone is found to be incorrectly
indicating a Message Waiting condition, the erroneous indication can be cleared manually.
To clear the MWI prompts; press CLEAR twice.
“Talking Text” SMS Messages
The IQ750 is compatible with the “Talking Text” SMS service. To access messages,
please refer to the guidelines issued by your service provider.
HOLDINGAND TRANSFERRING CALLS -This is dependent on your system type, so
please check your system’s Extension User Guide to find out how to use the RECALL
Key. It is sometimes known as the Flash or Facility Key.
34
PAUSE FUNCTION WHEN DIALING OUT
Sometimes a pause is necessary either when dialling ordirnary outgoing calls,
accessing specialised network features or perhaps when storing certain numbers in
the memory. If you have determined that a pause is required by your host system,
please refer to the information below. If you have already experienced dialling difficulties,
try the suggestions below.
AUTOMATIC TRUNK ACCESS DIGIT INSERTION
When the telephone is used wherever a dialing prefix is required to make an external call
(eg. normally 0 is needed for an outside line), this prefix can be stored to ensure that it is
automatically dialled whenever an external number is dialled from the Caller List. This
resolves a problem found in Caller ID capable network environments where the caller ID
information delivered to the receiving telephone does not contain the outside line prefix
necessary to complete a call-back to that caller.
To setup, model IQ750 accepts a one or two digit Trunk Access Code as follows:
1. Press STORE
2. Enter the TRUNK ACCESS DIGIT (example, 0 for Customnet)
3. Press STORE
4. Press “ ” (STAR)
After programming digit 0 in the above example the unit will insert a 0 in front of any
outgoing number that is dialled from the Caller List (the list of incoming calls).
This setting remains set until the user changes it - removal of power sources or line
connection will not change the setting.
AUTOMATIC PAUSE INSERTION
The above procedure will also insert a pause after the access code before dialling the
actual number that has been selected for call-back from the Caller List. The pause time
can be pre-set (see below).
35
PAUSE TIME
Sometimes the standard Pause time of 1 Second may be inappropriate, such as when a
shorter Pause is needed to slow down a code stored in memory so that the telephone
does not dial too quickly for the network.
EXAMPLE: A particular network typically needs a short Pause in the Call Hold function
code after “Recall” is sent to line and before “ 74” is dialled. A Pause time of 200mSec
is required in that code sequence. The required Call Hold code is Recall, Pause (insert
multiple Pause(s) here), (star),74.
Solution: Change the Pause time from the factory default of 1 Sec to 100mSec, and then
program the memory with enough Pauses inserted in the code to achieve the desired
Pause time.
FIRST change the pause time to 100mSec
1. Press STORE; the display will show “STORE”
2. Press
,
, STORE; the display will show “1-RECALL 2-PAUSE”
3. Press 2 to enter Pause Time Selection; the display will show “PAUSE 1 SEC”
(the factory default Pause time)
4. Press Scroll (the one above the DIAL key) Up or Down to select 100mS
5. Press STORE to confirm selection; the display will show “PAUSE STORED”.
THEN program the Call Hold function code with 200mSec of Pause time (two
100mSec Pauses) as follows:
1. Press STORE; display shows “STORE”
2. Press any memory key; the display shows “ENTER NUMBER”
3. Press RECALL, PAUSE (twice),
, 74; the display shows “FPP 74”
4. Press STORE; the display shows “ENTER NAME”
5. Enter text “CALL HOLD” on the keypad
6. Press “STORE”; the display shows “MEMORY STORED”
7. Test for resulting Pause time stored in that memory key for network compatibility by
pressing that memory key at the appropriate time and observing the result.
36
If two Pauses (i.e. 200 mSec) do not produce a long enough post-Recall pause for the
network switch, try three pauses (300mSec) or four (400mSec) or more.
The Pause time setting remains set until the user changes it - removal of power sources
or line connection will not change the setting.
HOLDING AND TRANSFERRING CALLS
The method used for these functions is dependent on your system type, so you will need
to check your system’s Extension User Guide. The RECALL Key is typically used to
transfer calls and the Recall Timing setting affects the Recall Key’s ability to function
correctly with your system (see below).
USING THE MEMORIES
Any combination of numbers,
and
, Pause, Recall and Handsfree commands can
be stored. You may find it useful to store some of your favourite network facility commands
in the telephone for fast, convenient access to those facilities (e.g.Diversion, Call Forward,
Call Back etc). Consult your system User Guide for the codes that you need to store.
TheDirectAccess Memories can be pre-programmed at point of sale with network feature
codes. For further information, please refer to the “Memory Operation” and “Memory
Protection Switch” sections of this manual.
Speed Dialing
When storing a number, you can add a “Speed Dialing” command to the start of the
number. This makes dialling faster and easier. The “H” command, entered by pressing
the HANDSFREE/HEADSET preceding the telephone number in the Memory Storage
procedure, activates the Handsfree function during dialing so that you can make a Handsfree
call just by pressing the memory key once it is programmed.
Cascade Memory Dialing
The contents of more than one memory can be “cascaded” or added together during a
call to create a long dialling sequence by pressing the required memory keys in the
desired order. This feature can be used to store unusually long numbers, which may
exceed the digit capacity of any individual memory.
37
9. INSTALLATION
GENERAL SETTING-UP
1. Fit the Coiled Cord to the appropriate sockets in the Handset and the telephone
base - please do not connect it to the Headset socket at the rear
2. Fit the Line Cord to the rear socket and to your telephone network outlet
3. Set the Ringer Volume and the Ringer Pitch controls
4. See following sections to complete the installation
5. If using a Headset, connect it to the Headset jack shown in Figure 9.
LINE CONNECTION
This telephone is supplied with an RJ45 Plug as the wall plug, with the centre pair being
reserved for speech and signalling. Other types of plugs and cords are available on request.
LOCATION
The telephone should be placed on a desk, table or shelf where it is not likely to be
pushed off. If the unit is to be wall-mounted, it should be seated securely on the WALL
MOUNT BRACKET illustrated in Figure 5B (please order separately). Avoid excessive
heat, damp, dust, direct sunlight, vibration, and other appliances or devices which may
transmit or emit electrical or electromagnetic radio frequency noise or signals (e.g.
computers, welders, pagers).
WALL MOUNTING
Use the IQ235 WALL MOUNT BRACKET or Wall Mount Kit No.3 shown in Figure 6B
(please order separately).
1. Prepare the IQ235 Wall Mount Bracket by ensuring that the appropriate lugs have
been cut or broken off as specified in Figure 8.
2. To enable the Handset to be supported in the cradle, follow the procedure shown in
Figure 7A to reverse the Handset Retainer
3. Connect the LINK CORD as shown
4. Fit the IQ235 WALL MOUNT BRACKET (optional, not supplied) to the underside of
the telephone and mount on the 7626 MODULAR WALL JACK (see Figure 7B).
38
FIGURE 6A : WALL MOUNTING
LINK CORD
LINK CORD
IQ235 WALL MOUNT BRACKET
(OPTIONAL, NOT SUPPLIED)
7626 MODULAR WALL JACK
(OPTIONAL, NOT SUPPLIED)
FIGURE 6B : IQ235 WALL MOUNT BRACKET. 7626 MODULAR WALL
JACK AND LINK CORD
Notes: 1. See Figure 8 for details of IQ235 Wall Mount Bracket
2. The IQ235 WALL MOUNT BRACKET, 7626 MODULAR WALL JACK and
LINK CORD illustrated in Figure 6B are available from your authorized
Interquartz dealer and can be ordered as Wall Mount Kit No.3.
39
LUG "B"
LUG "A"
MOUNTING
HOLE "E"
PIVOT FOR SWING-OUT
PLATE USED FOR
MODEL IQTEL 25
LUG "C"
LUG "D"
MOUNTING HOLE "F"
Please note:
1. This wall bracket may be secured onto the wall by using mounting holes “B” and
“D”
2. Lugs to break off before wall mounting the phone.
BREAK OFF LUGS
TELEPHONE MODELS
IQ 90
IQ750
IQ 150
IQ 250
IQ 260
IQ 360
IQ 350
IQ 450
IQ 550
IQ 560E
IQ E2
IQTEL 80
IQTEL 300
IQTEL 500
IQTEL E1
IQTEL E2
IQTEL E3
IQTEL ET
STUDIO 20
GEMINI SERIES
"B" and "D"
IQ E3
"A" and "C"
"A" ONLY
IQTEL 25
IQ 300
9853XT
9835 MKII
9836
9837
FIGURE 7: IQ235 WALL MOUNT BRACKET - BREAK-OFF LUGS
40
TECHNICAL ADJUSTMENTS - FOR CORRECT OPERATION
RECALL TIMING SELECTION
Two recall timings are available – 100 milliseconds and 1 Second.
To select a Recall Timing
1. Press STORE; the display will show “STORE”
2. Press
and
then STORE; the display will show “1-RECALL 2-PAUSE”
3. Press Digit 1 to enter Recall Timing Selection; the display will show “RECALL
100MS” (it is the factory default recall time)
4. Press the Scroll Key to select the desired timing. There are four different timings
of 100, 200, 300 and 600 mS for selection
5. Press STORE to confirm selection; the display will show “RECALL STORED”.
MESSAGE WAITING LIGHT COMPATIBILITY
No installation settings are required to enable the feature. If you have a PABX system,
the red lense in the top right hand corner will light when there is a message waiting. If the
light does not function correctly, your IQ750 may need an optional circuit to be added to
make it compatible with your system. If you have a Centrex system (eg. Spectrum) the
Caller key indicator and the “Mail” (envelope) icon will flash and “MESSAGE WAITING”
will be displayed. To retrieve your message, consult your voice mail system user guide.
HEADSET MIC ADJUST CONTROL
This control allows many different headsets on theAustralian market to function correctly
with the IQ750 telephone by adjusting the Headset Microphone sensitivity. The control is
located on the underside of the telephone (see Figure 8). The adjustment can be made
by a small screwdriver or similar implement that will fit into the control slot. Please see
Table 1 as a guide to the correct settings for some popular Headsets.
41
TO MAKE A HEADSET MIC LEVEL ADJUSTMENT
With the Headset connected as per the instructions in this manual:
1. Put the Headset on and lift the Handset to your other ear and make an outgoing call
2. Pressing the HANDSFREE/HEADSET Key, swap between Handset and Headset
modes (the indicator will illuminate when the Headset is in use). Do this a few
times while speaking to the other party by repeatedly pressing the HANDSFREE/
HEADSET Key while holding a conversation
3. Use the other party’s help to decide if your voice level is the same on the Headset in
comparison to the Handset
4. If you sound too loud on the Headset, reduce the microphone sensitivity (turn anti-
clockwise) so that your voice level when using the Headset matches that of the
Handset. Clockwise rotation increases the Headset Mic output level. Please see
Table 1 as a guide to the correct settings for some popular Headsets.
42
HEADSET POLARITY SWITCH
Located on the underside of the telephone (see Figure 8), this switch provides compatibility
with the two commonly-used headset wiring standards.
Position “V” suits Plantronics Vista Cords and other Headsets wired in the same
configuration (also known as “reversed” wiring mode).
Position “P” suits Plantronics P cords and other Headsets wired in the same configuration
(also known as “normal” wiring mode).
Please see Table 1 as a guide to the correct settings for most popular Headsets.
HEADSET JACK
RINGER PITCH
CONTROL
RINGER VOLUME
SWITCH
MOUNT HOLES FOR
WALL BRACKET
Reversed headset
polarity
HEADSET POLARITY
SWITCH
Normal headset
polarity
HANDSET JACK
VOLUME SLIDER
BATTERY COMPARTMENT
(OPTIONAL BATTERIES
NOT SUPPLIED)
HEADSET MIC
ADJUSTMENT CONTROL
FIGURE 8 HEADSET MIC ADJUST CONTROL AND POLARITY SWITCH
43
TABLE 1
44
10. GENERAL CARE AND MAINTENANCE
This telephone is a precision electronic instrument. While in use and storage, care should
be taken to avoid rough handling, extreme temperature, and damp or dirty environments.
CLEANING
NEVER use aerosol sprays or other chemical agents or substances that leave a residue
(furniture polish for example).
Use a mild detergent and a damp, clean cloth when cleaning. Do not allow moisture to
enter the telephone interior - damage may result!
FAILURE TO OPERATE AND SERVICE DIFFICULTIES
If telephone service problems occur at any time, it is recommended that the installation
procedure described in this manual be re-checked.
If a fault occurs, try to determine if the fault is with the telephone, or with the network or
system to which the telephone is connected:
Disconnect the “suspect” telephone, and test the line with a substitute telephone. If the
telephone service then operates satisfactorily, the fault is in the “suspect” telephone.
Test the “suspect” telephone on a known good line. If the fault still occurs, the fault is in
the “suspect” telephone.
Consult your Interquartz dealer for further advice if necessary.
45
11. THUNDERSTORMS
The telephone, in common with household electrical appliances, can be a source of
electric and acoustic shock during thunderstorms. The possibility of a telephone user
experiencing a shock is minimal. Nevertheless, customers should be aware of some
simple precautions to follow during thunderstorms:
Use your telephone only for calls of the utmost urgency. Keep these calls brief. Whilst
using your telephone keep clear of electrical appliances and metal fixtures such as :
stoves, air conditioners, refrigerators, window frames and sinks.
12. WARRANTY - 6 YEARS
Interquartz (A’Asia) Pty Ltd warrants the original purchaser against failure, under normal
usage and in the environment and network for which it was designed, resulting from
defective material and workmanship at time of manufacture for a period of SIX YEARS
from the date of purchase. Interquartz reserves the right to require proof of purchase and
proof of date of purchase to determine validity of this warranty. This warranty does not
cover defects or damage due to normal wear and tear, negligence, accidents, exposure
to radiation, misuse, obsolescence, incompatibility, improper maintenance, lightning
strikes or unauthorized repairs or modifications and excludes freight or postage costs to/
from your local authorized service centre unless otherwise arranged. Consequential loss
not included. Notification of any defect must be made within the warranty period before a
warranty repair can be effected. This guarantee is in addition to all other Warranties or
Guarantees expressed or implied by the Trade Practices Act or other Commonwealth or
State laws and all other obligations and liabilities on the part of Interquartz (A’Asia) Pty.
Ltd.
46
13. SERVICE AND PRODUCT SERVICES
Please call 1800 6 IQTEL (1800 647 835) or email [email protected] from
anywhere in Australia.
47
Manufactured by
International Quartz Limited
A Subsidiary of Chiaphua Industries Ltd.
©Copyright INTERNATIONAL QUARTZ LTD. 2004
|