Bolt-In-Place/Spring Button Front Rigging Kit
Assembly and Installation Instructions
Kits No. 1110266 and 1121271
SAVE THESE INSTRUCTIONS
NOTE: Check ALL parts for shipping damage. In case of shipping damage, DO NOT use. Contact
Carrier/Dealer for further instruction.
SAFETY SUMMARY
To ensure the safe installation of the Bolt-In-Place/Spring Button Front Rigging
Kit, these instructions MUST be followed:
WARN IN G
DO NOT install or use this equipm ent without first reading and understanding
these instructions and the Owner’s Manual supplied with the wheelchair. If you
are unable to understand the W arnings, Cautions or Instructions, contact a
healthcare professional, dealer or technical personnel before attem pting to
install this equipm ent - otherwise, injury or dam age m ay occur.
IN STA LLA TION WA RN IN G
After ANY adjustments, repair or service and before use, make sure all attaching
hardware is tightened securely - otherwise injury or damage may occur.
Bolt-In-Place Front Rigging Kit 1110266 contains the following items:
DESCRIPTION
QUANTITY
Riv Nut
Button Head Screw
1/8-inch Hex key
2
2
1
Spring Buton Front Rigging kit 1112127 contains the following items:
DESCRIPTION
QUANTITY
Spring buttons
4
IN STA LLIN G TH E BOLT-IN -PLA CE FOOTPLA TE KIT
(FIGURE 1 )
NOTE: This kit mounts the footplate assembly to the front rigging support so that tools are required
to remove or adjust the footrest assembly.
1. Remove the front rigging from the wheelchair. Refer to the wheelchair owner’s
manual shipped with wheelchair.
2. Pull up on the cam lock lever to unlock the cam.
NOTE: The elevating legrest has two (2) sets of release buttons, one (1) set above the other. Each
set will be visible one at a time allowing finer footplate height adjustment.
3. Push IN and hold the release button as shown in DETAIL “A” of FIGURE 1.
4. Rotate the lower footplate assembly 1/4 turn.
Part No. 1114831
1
Bolt-In-Place/Spring Button
Front Rigging Kit
BOLT-IN -PLA CE H EIGH T A DJUSTMEN T (FIGURE 1 )
NOTE: This procedure applies to the swingaway footrests and swingaway elevating legrest.
1. Remove the swingaway front rigging. Refer to INSTALLING/REMOVING THE
FRONT RIGGINGS in the owner’s manual shipped with wheelchair.
NOTE: Lay the front rigging assembly on a flat surface to simplify this procedure.
2. Pull the cam lock lever UP to UNLOCKED position.
3. Using a screw driver to hold the riv nut in position, remove the button head screw
from the riv nut.
4. Remove the riv nut and button head screw securing the footplate assembly to the
front rigging support.
5. Adjust the footplate assembly height by aligning the desired adjustment holes in the
upper front rigging support and footplate assembly.
6. From the outside of the swingaway front rigging, insert the riv nut through both the
front rigging support and the footplate assembly.
7. From the inside of the swingaway front rigging, insert the button head screw through
the appropriate adjustment hole and thread into the riv nut.
8. Using a screwdriver to hold the riv nut in position, securely tighten the button head
screw. Torque to 32 in-lbs.
9. Rotate cam lock lever DOWN to LOCKED position.
10. Repeat STEPS 1-9 to adjust the remaining footrest.
11. Reinstall the swingaway front rigging. Refer to INSTALLING/REMOVING THE
FRONT RIGGINGS in the owner’s manual shat shipped with wheelchair.
Part No. 1114831
3
Bolt-In-Place/Spring Button
Front Rigging Kit
IN STA LLIN G TH E SPRIN G BUTTON FRON T RIGGIN G
KIT (FIGURE 2 )
NOTE: This kit allows tool-less removal or adjustment of the footplate assembly.
1. Remove the front rigging from the wheelchair. Refer to the wheelchair owner’s
manual shipped with wheelchair.
\
2. Pull the cam lock lever UP to UNLOCKED position.
3. Using a screw driver to hold the riv nut in position, remove the button head screw
from the riv nut as shown in DETAIL “A” of FIGURE 2.
4. Remove the riv nut and button head screw securing the footplate assembly to the
front rigging support.
5. Remove the footplate assembly from the upper front rigging support.
6. Perform one of the following as shown in DETAIL “B” OF FIGURE 2:
A. FOOTRESTS:
•
With the spring pointing UP, insert the spring button into the footplate tube
so that the release buttons FULLY protrude through the top set of mounting
holes.
B. ELEVATING LEGRESTS AND FOOTRESTS WITH ADJUSTABLE ANGLE
FOOTPLATES:
•
With the spring pointing DOWN, insert the bottom spring button into the
footplate tube so that the release buttons FULLY protrude through the
bottom set of mounting holes.
•
With the spring pointing UP, insert the top spring button into the footplate
tube so that the release buttons FULLY protrude through the top set of
mounting holes.
NOTE: The elevating legrest has two (2) sets of release buttons, one (1) set above the other. Each
set will be visible one at a time allowing finer footplate height adjustment.
7. Insert the footplate tube into the front rigging support.
8. Push IN the release buttons and reposition the footplate assembly to the desired
height.
9. Ensure that the release buttons fully protrude from holes on both sides of the front
rigging support.
10. Rotate cam lock lever DOWN to LOCKED position.
11. Reinstall the swingaway front rigging assembly. Refer to the owner’s manual shipped
with wheelchair.
12. Ensure Release buttons are properly seated and FULLY protrude through the
adjustment holes before use.
13. Repeat this procedure for the other footplate, if necessary.
Bolt-In-Place/Spring Button
Front Rigging Kit
4
Part No. 1114831
DETAIL “A”
DETAIL “B”
Front Rigging Support
Spring
Front Rigging Support
Riv Nut
Spring Button
Release
Button
Release Buttons
Button
Head
Screw
Footplate
Assembly
Adjustment
Holes
Footplate
Assembly
FO O TRESTS
Spring
Cam Lock
Lever
Cam
Lock
Lever
Top Spring Button
Release Buttons
Bottom Spring Button
NOTE: Swingaway
footrests shown.
NOTE: Swingaway
footrest shown.
Spring
ELEVATING LEGRESTS/
FO O TRESTS W ITH
ADJUSTABLE ANGLE
FO O TPLATES
FIGURE 2 - INSTALLING THE SPRING BUTTO N FO O TPLATE KIT
SPRIN G BUTTON H EIGH T A DJUSTMEN T (FIGURE 2 )
NOTE: This procedure applies to the swingaway footrests and swingaway elevating legrest.
1. Remove the swingaway front rigging. Refer to INSTALLING/REMOVING THE
FRONT RIGGINGS in the owner’s manual shipped with wheelchair.
NOTE: Lay the front rigging assembly on a flat surface to simplify this procedure.
2. Pull the cam lock lever UP to UNLOCKED position.
NOTE: The elevating legrest has two (2) sets of release buttons, one (1) set above the other. Each
set will be visible one at a time allowing finer footplate height adjustment.
3. Push IN the release buttons and reposition the footplate assembly to the desired
height.
4. Ensure that the release buttons fully protrude from holes on both sides of the front
rigging support.
5. Rotate cam lock lever DOWN to LOCKED position.
6. Repeat this procedure for the other footplate, if necessary.
7. Reinstall the swingaway front rigging assembly. Refer to INSTALLING/REMOVING THE
FRONT RIGGING in the owner’s manual that shipped with wheelchair.
8. Ensure Release buttons are properly seated and FULLY protrude through the
adjustment holes before use.
Part No. 1114831
5
Bolt-In-Place/Spring Button
Front Rigging Kit
N OTES
Bolt-In-Place/Spring Button
Front Rigging Kit
6
Part No. 1114831
N OTES
Part No. 1114831
7
Bolt-In-Place/Spring Button
Front Rigging Kit
MADE IN MEXICO
Invacare Corporation
USA
One Invacare Way
Elyria, Ohio USA
44036-2125
Invacare is a registered trademark of
Invacare Corporation.
Yes, you can. is a trademark of
Invacare Corporation.
800-333-6900
© 2003 Invacare Corporation
Part No. 1114831
Rev B - 07/03
|