The style of communicating
Bluetooth Wireless Headset
BHS - 601
About Bluetooth™ Technology
Bluetooth is a technology for wireless communication between devices.
Bluetooth technology is based on a radio with a receiver and a transmitter, which have been built
into a tiny microchip. One of these microchips is incorporated in the Wireless Headset, and
another is integrated into the compatible mobile phone.
Bluetooth offers the ability to create wireless connections between the headset and mobile phone
within a radius of up to 10 meters, without a physical cable or line-of-sight connection.
Bluetooth Wireless Headset BHS-601 User Guide
Getting to Know Your Bluetooth Headset
Charging socket
Dual Color LED
Microphone
Figure 1.
First time use
–
–
Charge your headset
Pair your headset with a Bluetooth enabled mobile phone
Charging your headset:
AC Charger
USB Charger Cable
DC Car Charger
Figure 2.
The Bluetooth Headset comes with a built-in rechargeable battery. Before using this
headset, please fully charge the battery for the first time use.
Charging Options:
1. Plug AC Charger to power supply end of USB Cable, then plug mini USB connector end
of the USB Cable to charge jack of the headset.
2. Plug DC Car Charger to power supply end of USB Cable, then plug mini USB connector
end of the USB Cable to charge jack of the headset.
3. Plug the USB Cable to the USB Connector of a PC, then plug mini USB connector end of
the USB Cable to charge jack of the headset.
Normal Charging Time
Under normal usage, battery of headset will be full after 2 hours of charging. When battery is full,
headset will stop charging power automatically.
Charge Indication
When headset is charged, LED is red color constantly on. Once battery is full, LED turns off
automatically.
Talk & Standby Time
If battery is charged fully and under normal usage conditions, talk time is up to 5 hours / standby
time 120 hours.
Low Battery
When the headset is on and the battery becomes low, the LED will blink red color and the
headset will "beep" 3 times every 20 seconds. At that time, please recharge the battery as
described in the above step as "Charging Your Headset".
Turn on the Headset
Constantly press
color for 3 times.
Button for 5 seconds until you hear 2 short beeps. The LED will blink blue
Button for 2 seconds until you hear 2 short beeps. The LED will blink red
Turn off the Headset
Constantly press
color for 3 times.
Pairing Your Headset
This headset must use a Bluetooth enabled mobile phone. Configuration set up as below
for the first time use.
–
–
–
–
–
Keep headset and phone around 1 meter.
Assure headset is turned off.
Constantly press
Button until LED blinks red and blue in turn.
Initiate Bluetooth function of phone & search for Bluetooth devices.
Phone will start searching for Bluetooth devices. If it's successful, phone screen will show the
name of obtained device - "BHS-601". Press "Yes" to pair this headset to the phone.
Input ID code of headset - "0000". Press "Yes" to complete pairing. Meanwhile, this headset
is under Standby -mode - BLUE LED blinks 5 times.
–
–
Back to main menu of phone. Headset is under Standby -mode and ready for Bluetooth
communication. Please locate this headset within 10 meters (max.) to phone.
Notice: If pairing process cannot complete within 2 minutes, LED will stop blinking red and
blue in turn. Please follow up above steps to repairing again.
Link headset with phone
Once pairing is successful, headset is under Standby -mode. Please refer to procedure
below.
–
For incoming and outgoing calls, phone will link headset automatically. User can talk to
microphone of this headset for voice dialing or redial out the last phone number.
For incoming and outgoing calls, phone will link headset automatically. If phone has been cut
off link to headset, reconnect procedure as below.
–
1. Press
Button. Headset will be reconnected to phone and press "yes" on the phone
to accept reconnect mode.
2. Operate phone menu to Bluetooth function and then into program of paired device and
select "BHS-601".
–
When headset is under Standby -mode but cannot pick up/dial out call, please follow up
procedure as below for reconnect.
1. Press
Button. Headset will be reconnected to phone and press "yes" on the phone
to accept reconnect mode.
2. Operate phone menu to Bluetooth function and then into program of paired device and
select "BHS-601".
To Use Headset
To Dial a Call
When there is an active connection between the headset and the phone. Dial the number
normally on the phone.
To Answer a Call
When there is an incoming call, a ringing tone will come out of this headset. Press shortly
Button or the
Button to answer a call.
To Reject an Incoming Call
When there is an incoming call, ringing tone will come out of this headset. Press
3 seconds to reject a call.
Button for
To End a Call
During an active call, press
Button for 3 seconds to end call.
Switch between Headset and Phone
During an active call, press the
Phone –mode. Shortly press either
Headset –mode.
Button for 3 seconds to switch from Headset –mode to
Button or Button to switch from Phone –mode to
Mute
During an active call, press both buttons at the same time. Headset will beep. Press any one of
the buttons to disable mute.
Voice Activation
Under Standby -mode, press
Button or
Button for 1 second to activate Bluetooth
connection. User will hear a beep and then headset is available to use voice activation function.
Notice:
1. Before using voice activation, please assure that phone supports this function. (Voice
activation is subject to phones built-in with voice activation function and refers to voice
dialing procedure of individual phone.)
Last Number Redial
Under Standby –mode, press
phone call.
Button for 3 seconds, headset will dial out the last dialed
Volume Adjustment
During a call, press
reduce volume.
Button for 1 second to add volume, press
Button for 1 second to
To Reset the Headset
You may want to reset the headset to original setting. This also clears all current pairings.
1. Assure the headset is OFF.
2. Constantly press the
than 30 seconds).
Button until LED blinks red and blue color in turn (press more
3. Release the
Button.
4. Constantly press the
Button again until you hear 2 beeps.
5. Connect the headset to the charger for a few seconds.
6. The headset will turn off and return to the original setting mode. All the previous pairing
data will be cleared.
Warning
Headset
–
Please turn off this headset before putting it into your pocket or bag. If it is not turned off and
Button is pressed accidentally, this headset may dial out with unknown.
Do not expose the headset under liquid, moisture or humidity as it is not waterproof.
Do not use abrasive cleaning solvents to clean the headset.
Do not expose the headset under high or low temperatures.
Do not expose your headset to contact with sharpness objects as this will cause scratches
and damage.
–
–
–
–
–
–
Do not stick anything on inside of the headset as this may damage internal components.
Do not attempt to disassemble the headset as it does not contain serviceable components.
Built-In Battery
–
Do not attempt to replace the headset's battery by yourself as it is built-in and is not
changeable.
–
–
Only use the charger supplied of the manufacturer when charging the headset.
Do not disassemble the charger as it may expose you to dangerous voltages or other risks.
Incorrect reassembly can cause electric shock when the headset is subsequently used.
Do not use the charger outdoors or under humid environment.
Avoid charging the headset in extremely high or low temperatures.
–
–
Product Specifications
Bluetooth Specification:
Bluetooth Profile Supported:
Rang of Frequency:
Dimensions:
Nominal Charging Time:
Talk Time:
Version 1.1
Headset and Handsfree Profiles
2.4GHz Spectrum
66mm (L) x 21mm (W) x 11mm (H)
Within 2 hours
Up to 5 hours
Standby Time:
Up to 120 hours
Because operation of Bluetooth is dependent on individual phone, please refer to phone manual.
12 MONTH LIMITED WARRANTY
IQUA Ltd. warrants that this product is free from material and workmanship defects for a period of
12 months from date of purchase provided the following terms of this warranty are satisfied. The
warrant applies to the original owner of this product, only.
1. The purchaser must be able to proof the purchase by presenting original sales receipt
describing the product to establish the validity of the warranty claim to IQUA Ltd. at the
provider of warranty service. IQUA Ltd. shall have the right to deny warranty without
dated proof-of-purchase. Any evidence of alteration, erasure, or forgery results in
termination of the right of warranty.
2. IQUA Ltd. agrees to repair or replace without charge to the original owner any defective
product under warranty.
3. IQUA Ltd. will supply replacement parts free of charge for any IQUA product under
warranty upon request. Replacement or repair do not extend original warranty period.
4. This warranty is not valid for product owners who attempt to repair defective units.
5. Under Certain product liability regulations may apply to you as the owner of the Product,
however under no circumstances is IQUA Ltd. liable for any indirect or consequential
damages to person or property by the use of any IQUA products.
6. The warranty is not valid in case of fire, lighting, earthquake, accident, misuse, unusual
physical or electrical stress or any other cause beyond normal usage and care of the
product.
7. IQUA Ltd. reserves the right to make changes or improvements in design or manufacture
without having any obligation to install such changes in existing and sold products.
8. Warranty does not cover normal wear and tear of the product or the operation time of the
battery.
|