PRO SOUND
AVR580 QUICK-START GUIDE
COMES HOME™
®
Thank you for purchasing a JBL AVR580. This Quick-Start Guide will help
you with a basic system installation. For detailed information on any step,
please refer to the Owner’s Manual pages referenced in this guide. We
strongly recommend that you read the Owner’s Manual for complete details
on how to install, configure and operate the AVR580, as well as for the
important safety information it contains.
FRONT
RIGHT
SPEAKER
CENTER
SPEAKER
(Green)
FRONT
LEFT
SPEAKER
(Red)
FIGURE 1 – SPEAKER
PLACEMENT
The colors shown for each speaker correspond to
the matching output terminal connection on the
back of the AVR580 (see page 9).
(White)
SURROUND
RIGHT
SPEAKER
(Gray)
SUBWOOFER
(Purple)
CONNECTIONS COLOR
GUIDE
SURROUND
LEFT
SPEAKER
Audio Connections
Front
Left
Right
SURROUND
BACK
Center
RIGHT
(Blue)
Surround
SPEAKER
(Tan)
SURROUND
BACK
Subwoofer
LEFT
Surround Back
Digital Audio Connections
Coax
SPEAKER
(Brown)
Optical
Step 1. Place your speakers in the listening room
(see page 20).
Video Connections
Composite
S-Video
Match the colored jacks on the AVR580 to the appropriate
jacks on your source equipment or speakers. The colors are
standardized, but not all equipment or connectors use them.
SPEAKER PLACEMENT
FM Antenna
AM Antenna
CD PLAYER
Optical
L
R
Coax
COMP V2
COMP V1
REGION SELECTOR
AUDIO RECORDER
FIGURE 4 – AUDIO CONNECTIONS
Dashed lines (– – – –) indicate coax and optical digital audio con-
nections. Choose either type (but not both) for each digital audio
source.
REC/IN
PLAY/OUT
Step 4. Connect AM and FM antennas (Fig. 4) (see page 17).
Step 6. Region Selection: Set the Region Selector to “K” for South Korea.
Set it to “C” for China or Hong Kong. Set it to “S” for Singapore,
Malaysia, Indonesia or Thailand. (For other countries, please consult
your local JBL distributor.) The Main Power Switch (not just Standby)
must be turned off, then on again, in order for this selection to take
effect (see page 35).
Step 10. Configure speakers: No action is needed if you have five “small”
satellite-type speakers and a subwoofer. Otherwise, press the
Speaker button and then the Set and arrow buttons to select the cor-
rect speaker choices for your system (see pages 24–26).
Step 5. Connect source components, as shown in Figures 4 and 5, and in
the Device Connection Options chart on the back of this guide (see
pages 17–18).
AUDIO connections: Right channel (red) on source to right (red)
on AVR, and left channel (white) on source to left (white) on AVR.
DIGITAL AUDIO connections, if available: Choose either coax
(orange) to coax (orange) OR optical to optical for each device.
The Coax 1 input defaults to the DVD player, but may be reassigned.
Assign the other digital inputs and outputs as appropriate for your
equipment (see Step 8).
VIDEO connections: Choose component (Y/Pb/Pr – green/blue/
red), composite (yellow) or S-Video (4-pin) for each video source.
The devices connected to the Component Video 1 and 2 inputs must
be used with the DVD and Video 2 sources respectively. Connect the
component, composite and S-Video Monitor outputs to your Video
Monitor (TV). Switch your TV set’s input to match the type of video
used for the currently selected source.
Step 11. Use EzSet to set output levels: Set the Balance to 12 o’clock,
and the Volume to –10dB. Sit in the listening position and hold the
remote in front of you at shoulder level, pointing at the AVR580.
Press the SPL button for 3 seconds, and release it when the LED
flashes amber. Press “5” or “7” to indicate the number of speakers.
Hold the remote steady until the process is completed (see
pages 27–29).
Step 7. Depending on the electrical requirements in your area, you may need
to contact your JBL dealer to obtain the correct power cord. Plug all
components into AC power outlets.
Basic Receiver Configuration
Step 8. Select digital inputs: If your DVD is connected to Coax 1, no adjust-
ment is needed. For any other digital-device connections, use the
front-panel Digital Select button and the arrow buttons to select an
optical or coax digital input (see pages 22 and 32).
Step 12. Your system is configured – sit back and enjoy!
Step 9. Select a surround mode: Press the Surround Mode button on the
front panel to select Dolby® Pro Logic® II – Movie. (You may select
other modes later as you become familiar with the AVR580; see
pages 22–24 and 31–35.)
SPEAKER AND AUDIO CONNECTIONS
VCR (Video 1)
R
TV or Video Monitor (Video 3)
S-Video Component Video
Cable or Sat or HDTV Set-Top Box (Video 2)
Out
L
Video
Video
Component Video
L
R
Video
S-Video
Y
Pb
Pr
Y
Pb
Pr
In/Rec
In
Out/Play
Out
Optical
Coax
L
R
COMP V2
COMP V1
REGION SELECTOR
Component Video
Y
FIGURE 5 – VIDEO CONNECTIONS
Dashed lines (– – – –) indicate coax and optical digital audio connections. Choose either type (but not both) for each
L
R
Video
S-Video
digital audio source.
Pb
Pr
Dotted lines (••••) indicate component, composite or S-Video connections. Component video is the preferred connection
when available, but you may use any of the three types (but not more than one). When component, composite and
S-Video sources are connected to the AVR you must also connect all outputs from the AVR to your TV.
Optical
Coax
DVD PLAYER
Device Connection Options: Recommended connections are shown in red, but connections may be made to best fit your system requirements. The Video 4, Coax 3 and Optical 3 inputs are on the front panel of the receiver.
Device
CD Player
DVD Player
VCR
Input Name
CD
Audio Input Connections
Audio Output Connections
Not required
Video Connections
Not required
CD L/R Inputs, Optical Digital 1 or 2, or Coaxial Digital 1 or 2
Coaxial Digital 1 or 2, Optical Digital 1 or 2, or DVD L/R Inputs
Video 1 L/R Inputs
DVD
Not required
Component, Video 2, DVD Composite or S-Video
Video 1 Composite or S-Video Input and Output
Component Video 2, Video 2 Composite or S-Video Input
Not required
Video 1
Video 1 L/R Outputs
Cable Box or Satellite Receiver Video 2
Video 2 L/R Inputs, Optical Digital 3
*, or Coaxial Digital 3
*
Inputs
Not required
Audio Recorder
TV or Projector
Tape
Tape L/R Inputs, Optical Digital 1/2** or Coaxial Digital 1/2** Inputs
Video 3 L/R Inputs
Tape L/R Outputs, Digital Optical** or Coaxial Outputs**
Not required
Video 3
Monitor-Out Component, Composite and/or S-Video
Check with your cable service provider to determine whether digital audio is available for all channels. It may be necessary to make BOTH analog and digital connections if it is not. Digital audio recorders only.
*
**
PRO SOUND
COMES HOME™
VIDEO CONNECTIONS
®
|