P R X 7 1 0
P R X 7 1 2
P R X 7 1 5
U s e r ’ s G u i d e
P R X 7 1 5 X L F
P R X 7 1 8 X L F
P R X 7 2 5
P R X 7 3 5
CONTENTS
Important Safety Instructions............................................................. 4
Precautions ........................................................................................5
Suspension of Loudspeaker Systems............................................... 6
Watch for These Symbols ................................................................. 8
PRX700 Series Speakers Declaration of Conformity........................ 9
PRX700 Series Power Amplifier.......................................................10
Introduction To The PRX700 Series .................................................11
System Specifications ......................................................................13
System Setup - Full-Range Models..................................................16
System Setup - Subwoofers.............................................................18
Troubleshooting................................................................................20
Contact Information..........................................................................22
Warranty Information........................................................................23
3
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide
blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult
an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer,
or sold with the apparatus. When a cart is used, use caution when moving the
cart/apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been
damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have
fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or
has been dropped.
15. If Service Instructions are included in the Owner’s Manual: “CAUTION - THESE SERVICING
INSTRUCTIONS ARE FOR USE BY QUALIFIED SERVICE PERSONNEL ONLY. TO REDUCE THE RISK
OF ELECTRIC SHOCK DO NOT PERFORM ANY SERVICING OTHER THAN THAT CONTAINED IN THE
OPERATING INSTRUCTIONS UNLESS YOU ARE QUALIFIED TO DO SO.”
16. To completely disconnect this apparatus from the AC mains, disconnect the power supply cord plug
from the AC receptacle.
17. “WARNING – TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
APPARATUS TO RAIN OR MOISTURE.”
18. Do not expose this equipment to dripping or splashing and ensure that no objects filled with liquids, such as
vases, are placed on the equipment.
19. The main plug of the power supply cord shall remain readily operable.
Care And Cleaning
PRX700 series systems may be cleaned with a dry cloth. Do not get moisture into any of the openings in the
system. Ensure that the system is unplugged from the AC outlet before cleaning. In the event the DuraFlex
finish is damaged a touch up kit can be obtained from JBL Professional (part number 363972-001).
THIS APPARATUS CONTAINS POTENTIALLY LETHAL VOLTAGES. TO PREVENT ELECTRIC SHOCK OR
HAZARD, DO NOT REMOVE CHASSIS, INPUT MODULE OR AC INPUT COVERS. NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
4
PRECAUTIONS
The PRX700 series speakers covered by this manual are not intended for use in high
moisture environments. Moisture can damage the speaker cone and surround and cause
corrosion of electrical contacts and metal parts. Avoid exposing the speakers to direct
moisture. Keep speakers out of extended or intense direct sunlight. The driver suspension
will prematurely dry out and finished surfaces may be degraded by long-term exposure to
intense ultra-violet (UV) light. PRX700 series speakers can generate considerable energy.
When placed on a slippery surface such as polished wood or linoleum, the speaker may
move due to its acoustical energy output. Precautions should be taken to assure that the speaker does not fall
off a stage or table on which it is placed.
Stand Mounting Safety Precautions
Some PRX700 series models include a 36 mm receptacle cup to allow mounting on tripod stands or on a pole
over subwoofers. When using stands or poles, be sure to observe the following precautions:
• Check the stand or pole specification to be certain the device is designed to support the weight of the
speaker. Observe all safety precautions specified by the manufacturer.
• Always verify that the stand (or subwoofer/pole) is placed on a flat, level and stable surface and be
sure to fully extend the legs of tripod type stands. Position the stand so that the legs do not present a
trip hazard.
• Route cables so that performers, production crew, and audience will not trip and topple the speakers over.
• Inspect the stand (or pole and associated hardware) before each use and do not use equipment with
worn, damaged or missing parts.
• Do not attempt to place more than one PRX700 series speaker on a stand or pole.
• Always be cautious in windy, outdoor conditions. It may be necessary to place additional weight
(i.e. sandbags) on the base of the stand to improve stability. Avoid attaching banners or similar items to
any part of a speaker system. Such attachments could act as a sail and topple the system.
• Unless you are confident that you can handle the weight of the speaker, ask another person to help
you get it onto the tripod stand or pole.
• JBL highly recommends that no more than 80 lbs of weight be placed on a speaker pole that is
mounted to a PRX715XLF or PRX718XLF.
Suspension of Loudspeaker System
Before attempting to suspend your JBL loudspeakers, read and understand the following safety information.
IMPORTANT SAFETY WARNING!
The information in this section has been assembled from recognized engineering data and is intended for
informational purposes only. None of the information in this section should be used without first obtaining
competent advice with respect to applicability to a given circumstance. None of the information presented herein
is intended as a representation or warranty on the part of JBL. Anyone making use of this information assumes
all liability arising from such use. All information presented herein is based upon materials and practices
common to North America and may not directly apply to other countries because of differing material
dimensions, specifications, and/or local regulations. Users in other countries should consult with appropriate
engineering and regulatory authorities for specific guidelines. Correct use of all rigging hardware is required for
secure system suspension. Careful calculations should always be performed to ensure that all components are
used within their working load limits before the array is suspended. Never exceed the maximum recommended
load ratings. Before suspending any speaker system always inspect all components (enclosure, rigging frames,
pins, eyebolts, track fittings, etc.) for cracks, deformations, corrosion, missing, loose or damaged parts that could
reduce strength and safety of the array. Do not suspend the speaker until the proper corrective action has been
taken. Use only load-rated hardware when suspending JBL suspendable loudspeaker models.
5
SUSPENSION OF LOUDSPEAKER SYSTEMS
Are You New to Rigging?
If you are new to rigging, you should do the following:
• Read and study JBL Technical Note Volume 1, Number 14: Basic Principles for Suspending Loudspeaker
Systems (available at http://www.jblpro.com/catalog/support/getfile.aspx?docid=296&doctype=3).
• Know the rules for safe rigging.
• Attend a safe rigging seminar, such as that presented by professionals like Rigging Seminars™ or by Chain
Motor Hoist manufacturers like Columbus McKinnon Corp. (manufacturers of the C/M Lodestar).
• Meet and establish a relationship with a licensed mechanical or structural engineer. Get in the habit of asking
them questions instead of guessing about their answers. Learn from what they tell you.
• Meet and discuss this aspect of your business with your Insurance Agent.
• Research and understand the codes, practices, and requirements in the venues where you intend to
operate your sound system.
General Hardware Information
Any hardware used in an overhead suspension application must be load rated for the intended use. Generally,
this type of hardware is available from rigging supply houses, industrial supply catalogs and specialized rigging
distributors. Local hardware stores do not usually stock these products. Hardware that is intended for overhead
suspension will comply with ASME B30.20 and will be manufactured under product traceability controls.
Compliant hardware will be referenced with a working load limit (WLL) and a traceability code.
Attachment to Structures
A licensed Professional Engineer must approve the placement and method of attachment to the structure prior
to the installation of any overhead object. The following performance standards should be provided to the
Professional Engineer for design purposes; Uniform Building Code as applicable, Municipal Building Code
as applicable, and Seismic Code as applicable.
The installation of the hardware and method of attachment must be carried out in the manner specified by
the Professional Engineer. Improper installation may result in damage, injury or death.
Inspection & Maintenance
Suspension systems are comprised of mechanical devices and, as such, they require regular inspection and
routine maintenance to insure proper function ability. JBL suspendable loudspeakers must be inspected for
fatigue at least annually or, if there has been significant seismic activity, immediately thereafter. The inspection
shall include a visual survey of all corners and load bearing surfaces for signs of cracking, water damage,
de-lamination, or any other condition that may decrease the strength of the loudspeaker enclosure. Accessory
suspension hardware provided with or for the JBL loudspeakers must be inspected for fatigue at least annually.
The inspection shall include a visual survey of the material for signs of corrosion, bending or any other condition
that may decrease the strength of the fastener. Additionally, any eyebolts shall be checked for possible spin-out
of the enclosure.
For all other hardware and fittings, refer to the hardware manufacturer’s inspection and maintenance
guidelines for process.
JBL is not responsible for the application of its products for any purpose or the misuse of this information for
any purpose. Furthermore, JBL is not responsible for the abuse of its products caused by avoiding compliance
with inspection and maintenance procedures or any other abuse.
Prior to suspending the system, an expert, trained and experienced in suspending speaker systems should
inspect all rigging parts and components.
6
Resources
Adaptive Technologies Group
McMaster Carr
562.424.1100
Various locations in the USA
For a location near you, visit
1635 E. Burnett Street
Signal Hill, CA 90755
JBL Professional - Tech Note Vol. 1 No. 14
“Basic Principles for Suspending Loudspeakers”
Safe Rigging
JBL suspendable version loudspeakers are supplied with built-in internal brackets. The systems are designed
to facilitate the suspension of the loudspeaker by a qualified person familiar with rigging hardware and industry
practices. Improper installation may result in damage, injury or death.
If you are unfamiliar with Safe Rigging Practices you will need to consult with a qualified person familiar
with rigging hardware and industry practices.
Working Load Limit
Working Load Limit for M10 Suspension Points:
The working load limit (WLL) of the JBL PRX700 Series loudspeakers utilizing M10 attachment points will be
maintained with a safety factor of 5:1, provided no more than 470lbs/213kg from 2 points equally loaded, or no
more than 235lbs/106kg maximum from a single suspension point, is utilized in conjunction with industry
recognized safe rigging practices and the guidelines established within this manual.
For permanent installation applications utilizing the M10 suspension points order JBL 229-00009-01.
This kit includes three M10 x 35 mm forged shoulder steel eyebolts with washers.
WARNING
Suspension of JBL loudspeakers must employ a minimum of two attachment points. When “bridling” a JBL
loudspeaker system, two legs of equal length must be used. The rear attachment points are pull-back points and
are intended only for use in adjusting the down-angle of the speaker enclosure. Only the top and bottom
attachment points are intended for use as suspension points.
Hearing Damage, Prolonged Exposure To Excessive SPL
PRX700 series loudspeakers are easily capable of generating sound pressure levels (SPL) sufficient to cause
permanent hearing damage to performers, production crew and audience members. Caution should be taken to
avoid prolonged exposure to SPL in excess of 90 dB.
7
SUSPENSION OF LOUDSPEAKER SYSTEMS
The lightning flash with arrowhead symbol within
an equilateral triangle, is intended to alert the
user to the presence of uninsulated. “Dangerous
Voltage” within the products enclosure that may be
of sufficient magnitude to consitute a risk of
electric shock to persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (Servicing) instructions in
the literature accompanying the product.
8
PRX700 Series Speakers Declaration of Conformity
Safety and EMC Compliance Specifications
EN 55103-1:1997 Electromagnetic Compatibility - Product Family Standard for Audio, Video, Audio-Visual
and Entertainment Lighting Control Apparatus for Professional Use, Part 1: Emissions
EN 55103-1:1997 Magnetic Field Emissions-Annex A@ 10 cm and 20 cm
EN 55022:2003 Limits and Methods of Measurement of Radio Disturbance Characteristics
of ITE: Radiated, Class B Limits; Conducted, Class A
EN 55103-2:1997 Electromagnetic Compatibility - Product Family Standard for Audio, Video, Audio-Visual
and Entertainment Lighting Control Apparatus for Professional Use, Part 2: Immunity
EN 61000-4-2: A2:2001 Electrostatic Discharge Immunity (Environment
E2-criteria B, 4 kV Contact, 8 kV Air discharge)
EN 61000-4-3:2003 Radiated, Radio-frequency, Electromagnetic Immunity (Environment E2, criteria A)
EN61000-4-4:2005 Electrical Fast Transient/Burst Immunity (criteria B)
EN 61000-4-5:2001 Surge Immunity (criteria B)
EN 61000-4-6:1996 Immunity to Conducted Disturbances Induced by Radio-Frequency Fields (criteria A)
EN 61000-4-11:2004 Voltage Dips, Short Interruptions and Voltage Variation
UL 6500 2nd Edition 1999 Audio/Video and Musical Instruments Apparatus for Household, Commercial,
and Similar General Use
CAN/CSA-E60065-00 Audio, video and similar apparatus - Safety requirements
UL Compliance Specifications
CUL 60065 7th Ed. IEC 60065(ed.7), IEC 60065(ed.7);am1,
IEC 60065(ed.7);am2 EN 60065:2002/A1:2006/A11:2008/A2:2010/A12:2011
FCC Compliance Notice
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to part of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful interference to radio
communications. However there is no guarantee that the interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio and television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to collect the interference by one or more of the
following measures.
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio / TV technician for help.
9
The PRX700 Series Power Amplifier
AC Power Requirements
Standard PRX700 series speaker systems are equipped with a multi-channel Class-D power amplifier
and loudspeaker specific DSP electronics and require appropriate AC power. Before plugging a PRX700
speaker into an outlet ensure that it is able to provide the appropriate AC power as required by the speaker.
A robust AC supply is necessary for maximum performance. If the supply is too weak the bass performance may
be affected and if it sags (drops) too much the system may self-mute to protect itself. As soon as the appropriate
AC supply is restored it will continue to operate. Plugging multiple systems into the same outlet and long
extension cord runs may affect the AC supply to the systems.
CAUTION
In compliance with safety agency criteria and proper system operation, it is critical that the system installer
observe all electrical safety practices at all times and provide proper earth grounding for all AC Power
connections.
Powering Up
The main power switch is located on the input panel on the back of the enclosure. Always ensure that the
speaker system is the last thing you power up, and the first thing to turn off when operating your complete PA
system. If speaker systems are daisy chained together always turn off the last system in the chain first. Power
“on” is indicated by the illumination of the blue LED on the front of the enclosure.
Operating Temperature
The design of the amplifier is such that it is very energy efficient and as a result does not get really hot.
In the rare event that it does get too hot it will automatically shut down to protect itself. When its temperature
has returned to within its operating range it will turn back on. A condition under which this may occur is when the
system is operated in very high ambient temperatures or the rear of the enclosure is in direct sunlight. Always
ensure adequate cooling and appropriate shade.
10
Introduction to the PRX700 Series
PRX710
PRX712
PRX715
PRX715XLF
PRX718XLF
PRX725
PRX735
Thank you for choosing the JBL PRX700 series self-powered PA loudspeakers. The PRX700 Series represent
an evolutionary step in the efficient use of amplifier power, rugged durability and enhanced versatility in a self
powered loudspeaker. The speakers were designed from the ground up to perform in the real world of sound
reinforcement where challenging audio environments, high ambient noise levels and loud volumes are the norm.
And we’ve built these speakers to last a lifetime using tour tested technology that’s reliable and trustworthy.
Knowing you can rely on your system to deliver everything you need gives you the freedom to deliver your best.
That’s performance you can trust. With the PRX700 Series, as always, JBL delivers with precision and care.
Properly maintained, your PRX700 series speaker will provide you with many years of flawless performance. To
ensure you are always receiving optimum performance we encourage you to review this user’s guide completely
before hooking up your new system.
The PRX700 Series is a platform technology that allows you to create the system you need from an intelligent
range of models. While each model was designed to excel at a specific application, the PRX Series integrate
seamlessly with one another offering a multitude of choices when tailoring a system to fit your specific needs.
Whether you need a single speaker on a stand for public address situations, a full-range stereo set up with two
top cabinets and a sub-woofer for live performance or DJ applications, or multiple cabinets for a scalable, highly
professional sound reinforcement situation, the PRX700 Series offers the solutions. In fact, you can even
suspend any of the top cabinets for use in a commercial installation or House of Worship. If versatility, scalability,
portability and affordability are what you’re looking for in a system, PRX700s are the intelligent choice.
Road Tough
All PRX700 cabinets are built from a combination of 25mm (on the top and bottom for added rigidity) and 18mm,
strong, lightweight poplar plywood made structurally sound with tongue and groove joints. All PRX700 Series
cabinets are protected by JBL’s tour proven DuraFlex™ finish. We make our grilles from dent-resistant 16 gauge
steel and our handles are made from lightweight glass-filled nylon for added durability. All M10 suspension
points are constructed from 14 gauge steel and the M10 suspension points have been tested with a yield-
strength of 1000 lbs. each.
Differential Drive Transducers
Extended frequency response, high power output and low distortion are hallmarks of all JBL transducers. Our
tour tested, tour proven and patented Differential Drive® technology delivers all this performance in a dramati-
cally lighter package than traditional transducer designs.
11
Powered Speaker Systems
A Closed System Architecture…
There is much confusion these days in the world of powered speakers especially when it comes to defining
“performance”. What constitutes “exceptional performance”? Is it wattage ratings, driver dimensions, cabinet
dimensions, sound pressure levels, tone? It can get very confusing when you’re confronted with a barrage of
specifications from manufacturers all claiming to have the “best performance”. A self powered speaker is really
a “system” unto itself – it’s a “closed system”. Unlike a passive speaker, amplifier and signal processing chain
where components can be interchanged or upgraded, the powered speaker is a “closed system” that operates
as a single unit. Properly designed, all of the components are chosen to work together, complementing each
other to create an environment where the whole is greater than the sum of the parts. The cabinet volume needs
to support the mechanical performance of the speaker which is impacted by the power amplifier’s performance
which, if there is Digital Signal Processing on the input, is affected by the DSP programming. Some manufactur-
ers simply stick an amplifier on an existing speaker cabinet and call it a “powered speaker” (technically correct)
while more experienced companies, like JBL, spend hundreds of man hours optimizing the relationship between
the components in order to maximize amplifier and speaker efficiency, spectral balance, tone and dependability.
Here at JBL we not only work hard on the system but on our proprietary components as well. Products like Dif-
ferential Drive® speakers for example are patented designs born from years of dedicated research and develop-
ment into acoustical and transducer science. No one else has access to this technology and Differential Drive®
speakers have been tested on worldwide concert tours for years.
Harman Professional “Green Edge™” Mission
At Harman Professional we understand and respect that we have a duty to serve our customers and our em-
ployees by serving the planet. We accept that responsibility and strive to be energy efficient and environmentally
minded in our everyday business. When we design, produce, and deliver our products we look for opportunities
to do so more efficiently and sustainably. We’re committed to a healthier planet and healthier life for every living
thing. JBL is proud that PRX700s have been certified “Green Edge” compliant by Harman Professional. We’ve
not only lowered our Carbon Footprint, but the CF of any one who purchases them.
12
SYSTEM SPECIFICATIONS
Full-Range Models
PRX710
PRX712
PRX715
PRX725
PRX735
SYSTEM SPEC
System Type: Self powered two-way 10”
woofer 1” exit compression
driver, bass reflex
Self powered two-way 12”
woofer 1” exit compression
driver, bass-reflex
Self powered two-way 15”
woofer 1” exit compression
driver, bass-reflex
Self powered two-way 15”
woofer 1” exit compression
driver, bass-reflex
Self powered three-way, 15”
woofer, 6.5” midrange, 1” exit
compression driver, bass-reflex
Max SPL Output: Normal: 133 dB
Normal: 135 dB
Boost: 135 dB
Normal: 136 dB
Boost: 136 dB
Normal: 139dB
Boost: 139 dB
Normal: 136 dB
Boost: 136 dB
Boost: 133 dB
Freq Range (-10 dB): Normal: 50 Hz -19.6 kHz
Main: 44.8 Hz -19.6 kHz
Monitor: 44.8 Hz -19.5 kHz
Main: 42.9 Hz – 19.5kHz
Monitor: 43.6 Hz – 19.3kHz
Normal: 42 Hz – 18.5 kHzBoost:
40 Hz – 18.5 kHz
Normal: 35 Hz – 20 kHz
Boost: 34 Hz – 20 kHz
Boost: 42.9 Hz -20 kHz
Freq Response ( 3 dB): Normal: 63.5 Hz -18.5 kHz
Main: 55.7 Hz -18.2 kHz
Monitor: 56.5 Hz -17.7 kHz
Main: 58.1 Hz – 17.2kHz
Monitor: 60.7 Hz – 16.7kHz
Normal: 49 Hz – 17 kHz
Boost: 46 Hz – 17 kHz
Normal: 42 Hz – 20 kHz
Boost: 39 Hz – 20 kHz
Boost: 53 Hz -18.6 kHz
Input Connectors: 2 x Balanced XLR / ¼” input, 2 x
2 x Balanced XLR / ¼” input, 2 x
unbalanced RCA input
2 x Balanced XLR / ¼” input, 2 x
unbalanced RCA input
2 x Balanced XLR / ¼” input, 2 x
unbalanced RCA input
2 x Balanced XLR / ¼” input, 2 x
unbalanced RCA input
unbalanced RCA input
Input Impedance: 20K Ohms (balanced), 10K Ohms 20K Ohms (balanced), 10K Ohms 20K Ohms (balanced), 10K Ohms 20K Ohms (balanced), 10K Ohms 20K Ohms (balanced), 10K Ohms
(unbalanced)
(unbalanced)
(unbalanced)
(unbalanced)
(unbalanced)
Signal Indicators: Limit: Yellow LED indicates peak
Limit: Yellow LED indicates peak
Limit: Yellow LED indicates peak
Limit: Yellow LED indicates peak
Limit: Yellow LED indicates peak
output has been reached and dsp output has been reached and dsp output has been reached and dsp output has been reached and dsp output has been reached and dsp
limiter is acting limiter is acting limiter is acting limiter is acting
limiter is acting
Signal: Green LED indicates signal Signal: Green LED indicates signal Signal: Green LED indicates signal Signal: Green LED indicates signal Signal: Green LED indicates signal
present
present
present
present
present
Power/Standby: Blue indicates
system has power and ready to
Power/Standby: Blue indicates
system has power and ready to
Power/Standby: Blue indicates
system has power and ready to
Power/Standby: Blue indicates
system has power and ready to
Power/Standby: Blue indicates
system has power and ready to
pass audio, Red indicates system pass audio, Red indicates system pass audio, Red indicates system pass audio, Red indicates system pass audio, Red indicates system
has power but is in a power sav- has power but is in a power sav- has power but is in a power sav- has power but is in a power sav-
has power but is in a power sav-
ing mode and will not pass audio. ing mode and will not pass audio. ing mode and will not pass audio. ing mode and will not pass audio. ing mode and will not pass audio.
EQ: Presets for Normal and Boost
Presets for Main and Monitor
dbx Type IV™ limiter circuit
1.8 kHz
Presets for Main and Monitor
dbx Type IV™ limiter circuit
1.7 kHz
Presets for Normal and Boost
dbx Type IV™ limiter circuit
2.4 kHz
Presets for Normal and Boost
dbx Type IV™ limiter circuit
480 Hz, 2.0 kHz
Dynamic Control (Input): dbx Type IV™ limiter circuit
Crossover 1.9 kHz
Frequency:
AMPLIFIER
Design: Class-D
Power Rating: 1500W (2 x 750W)
AC Power Input: 100V - 240V~ 50/60 Hz
SPEAKER
Class-D
Class-D
Class-D
Class-D
1500W (2 x 750W)
100V - 240V~ 50/60 Hz
1500W (2 x 750W)
100V - 240V~ 50/60 Hz
1500W (2 x 750W)
100V - 240V~ 50/60 Hz
1500W (2 x 750W)
100V - 240V~ 50/60 Hz
LF: 1 x JBL M110-4 250mm (10
1 x JBL 272G 305mm (12”)
woofer
1 x JBL 275G (15 in) woofer
n/a
2 x JBL 275 (15 in) woofer
n/a
1 x JBL 275G 380mm (15 in)
woofer
in) woofer
MF: n/a
n/a
1 x JBL 196H 165mm (6.5 in)
horn-loaded midrange transducer
HF: 1 x JBL 2408H-2 37.5 mm (1.5”) 1 x JBL 2408H-2 37.5 mm (1.5”) 1 x JBL 2408H-2 37.5 mm
1 x JBL 2408H-2 37.5 mm
(1.5””) annular polymer dia-
1 x JBL 2408H-2 37.5 mm
(1.5””) annular polymer dia-
annular polymer diaphragm,
annular polymer diaphragm,
(1.5””) annular polymer dia-
neodymium compression driver
neodymium compression driver
phragm, neodymium compression phragm, neodymium compression phragm, neodymium compression
driver”
driver”
driver”
Coverage Pattern: 100º x 60º nominal
Directivity Index (DI): 9 dB
Directivity Factor (Q):
90º x 50º nominal
90º x 50º nominal
90º x 50º nominal
90º x 50º nominal
10.5 dB
10.2 dB
10.2 dB
10.4 dB
8
10.4
10.4
11
11.2
Enclosure: Trapezoidal, 18 mm, plywood
Asymmetrical, 18 mm, plywood
Asymmetrical, 18 mm, plywood
Trapezoidal, 18 mm, plywood
Trapezoidal, 18 mm, plywood
12 x M10 Suspension Points
Suspension/Mounting: Single 36 mm pole socket, 8 x
M10 Suspension Points,
Dual 36 mm pole socket, 12 x
M10 Suspension Points
Dual 36 mm pole socket, 12 x
M10 Suspension Points
8 x M10 Suspension Points, 1 x
M10 pull back point
1 x M10 pull back point
Transport: 1 x integrated handle with injec-
1 x injection molded handles with 1 x injection molded handles with 2x injection molded handle with
2x injection molded handle with
backing cup
tion molded backing cup
backing cup
backing cup
backing cup
Finish: Obsidian DuraFlex™ finish
Obsidian DuraFlex™ finish
Obsidian DuraFlex™ finish
Obsidian DuraFlex™ finish
Obsidian DuraFlex™ finish
Grille: Powder coated, Obsidian, 16
Powder coated, Obsidian, 16
gauge perforated steel with
Powder coated, Obsidian, 16
gauge perforated steel with
Powder coated, Obsidian, 16
gauge perforated steel with
Powder coated, Obsidian, 16
gauge perforated steel with
gauge perforated steel with
acoustical transparent black cloth acoustical transparent black cloth acoustical transparent black cloth acoustical transparent black cloth acoustical transparent black cloth
backing.
backing.
backing.
backing.
backing.
Dimensions (mm): 498.720 x 335.617 x 322.280
(H x W x D) (in): (19.63 x 13.21 x 12.69)
612.4 x 384.6 x 341.4
24.11x 15.14 x 13.44
714.4 x 445. x 358.7
28.13 x 17.52 x 14.12
1070.4 x 445 x 538
42.14 x 17.52 x 21.18
952.5 x 445 x 538
37.5 x 17.52 x 21.18
Net Weight: 16.4 kg (36 lb)
19.4 kg (42.5 lb)
21.6 kg (47.5 lb)
37.19 kg (82 lb)
34.9 kg (77 lb)
13
SYSTEM SPECIFICATIONS
Subwoofers
PRX715XLF
PRX718XLF
SYSTEM SPEC
System Type: Self powered 15”, bass-reflex
Max SPL Output: 131 dB
Self powered 18”, bass-reflex
134 dB
Frequency Range (-10 37 Hz - 113 Hz
30 Hz - 103 Hz
dB):
Frequency Response 44 Hz – 91 Hz
35 Hz - 87 Hz
(
3 dB):
Input Connectors: Two Balanced female XLR/ 1/4”
Two Balanced female XLR/ 1/4”
combo connectors
combo connectors
Input Impedance: 20K Ohms (balanced)
20K Ohms (balanced)
Signal Indicators: Limit: Yellow LED indicates peak
Limit: Yellow LED indicates peak
output has been reached and dsp output has been reached and dsp
limiter is acting limiter is acting
Signal: Green LED indicates signal Signal: Green LED indicates signal
present
present
Power/Standby: Blue indicates
system has power and ready to
pass audio, Red indicates system
has power but is in a power sav-
Power/Standby: Blue indicates
system has power and ready to
pass audio, Red indicates system
has power but is in a power sav-
ing mode and will not pass audio. ing mode and will not pass audio.
EQ: n/a
n/a
Dynamic Control (Input): dbx Type IV™ limiter circuit
dbx Type IV™ limiter circuit
Crossover Internal: 90 Hz DSP controlled 48
Frequency: dB filter slope
Internal: 90 Hz DSP controlled 48
dB filter slope
AMPLIFIER
Design: Class-D
Power Rating: 1500W
Class-D
1500W
AC Power Input: 100V - 240V~ 50/60 Hz
SPEAKER
100V - 240V~ 50/60 Hz
LF: 1 x JBL 2275H 15 in woofer
1 x JBL 2278G 460 mm (18 in)
woofer
MF: n/a
HF: n/a
n/a
n/a
Coverage Pattern: n/a
Directivity Index (DI): n/a
Directivity Factor (Q): n/a
n/a
n/a
n/a
Enclosure: Rectangular, 18 mm & 25mm,
Rectangular, 18 mm, plywood
plywood
Suspension/Mounting: n/a
n/a
Transport: 2 x injection molded handles with 2 x injection molded handles with
backing cup
backing cup
Finish: Obsidian DuraFlex™ finish
Obsidian DuraFlex™ finish
Grille: Powder coated, Obsidian, 16
Powder coated, Obsidian, 16
gauge perforated steel with
gauge perforated steel with
acoustical transparent black cloth acoustical transparent black cloth
backing.
backing.
Dimensions (mm): 547.1 x 445 x 580
(H x W x D) (in): 21.54 x 17.52 x 22.48
690.4 x 523.2 x 723.9
27.18 x 20.6 x 28.5
Net Weight: 25.4 kg (56 lb)
36.8 kg (81 lb)
14
15
SYSTEM SET UP - FULL RANGE MODELS
PRX700 Amplifier Input Configuration for
PRX710, PRX712, PRX715, PRX725 and PRX735:
2
3
1
5
11
12
4
6
7
8
13
9
10
16
FEATURES
1. Selectable System EQ
a. Normal and Boost (PRX710, PRX725, & PRX735 only) – When set in the “Normal” position, frequency
response is linear and unaltered. When “Boost” is selected, internal equalization is applied to enhance low
frequency and high frequency response. “Normal” will provide greater accuracy of reproduced music and
higher speech intelligibility. “Boost” is particularly useful at lower levels to enhance the low and high
frequencies of pre-recorded music. This feature provides flexibility without the need to use an
external equalizer. The LED will illuminate GREEN when NORMAL is selected and YELLOW when
BOOST is selected.
b. Main and Monitor (PRX712 & PRX715 only) – Switching between “Main” and “Monitor” optimizes the
system for use as either a main full-range system or a stage monitor. The LED will illuminate GREEN
when MAIN is selected and YELLOW when MONITOR is selected.
2. PWR/STBY LED – This LED illuminates when the “Power Switch” has been turned to the on position. It will
illuminate BLUE when the system has power and is ready to pass audio. It will illuminate RED when the
system is in power save mode and not passing audio.
3. FRONT LED – This push button allows you to turn on/off the Power LED on the front of the speaker. The
front LED will illuminate BLUE when the system has power and is ready to pass audio. When the front LED
turn RED that means the system is in power save mode and not passing audio.
4. SIGNAL Indicator – There are two LED indicators (one for each channel) that will illuminate GREEN when
signal is present at the input connector.
5. LIMIT Indicator – There is one YELLOW LED indicator that will illuminate when peak output has been
reached and the DSP limiter is acting.
6. GAIN Knobs – This gain knob is for setting the input level of CH1 and CH2.
7. MIC/LINE Button – This push button allows you to choose between MIC or LINE level on CH1 only. CH2 is
always line level.
8. GROUND LIFT Button – This push button allows you to lift the ground on CH2 only reducing unwanted hum
and buzz caused by ground loops in the system.
9. XLR Inputs – Female balanced XLR and 1/4 inch phone jack combo input connectors.
10. RCA Inputs – Female unbalanced RCA input connectors.
11. SPK SELECT Switch – This switch determines which inputs are fed through to the amplifier. If CH1 is
selected only the audio on CH1 will pass through to the speaker. If CH2 is selected only the audio on CH2
will pass through to the speaker. If MIX is selected, the audio on both CH1 and CH2 will pass through to
the speaker.
12. THRU SELECT Switch – This switch determines which inputs are sent out of the THRU connector. If CH1
is selected, only the audio on CH1 will be sent out via the THRU connector. If CH2 is selected, only audio
on CH2 will be sent out via the THRU connector. If MIX is selected, the audio on both CH1 and CH2 will be
sent out via the THRU connector at a 50/50 mix. The signal sent out of the THRU connector is before the
GAIN knob so any change in level via the GAIN knob will not be reflected on the signal that is sent out.
13. THRU Connector – Male balanced XLR output connector. This connector provides a full-range signal
which can be daisy chained to another speaker.
17
SYSTEM SET UP - SUBWOOFERS
PRX700 Amplifier Input Configuration for
PRX715XLF and PRX718XLF:
3
4
1
2
5
6
7
8
9
18
FEATURES
1. POLARITY Button – This push button allows you to choose between 0° (Normal) or 180° (Inverse Polarity).
The correct polarity setting will produce the best blend between the subwoofer and the full-range speaker and
the strongest perceived bass response at the listening position. If the bass response seems weak, try
inverting the polarity.
2. PASS THRU Button – This push button determines whether the signal coming out of the THRU connector
is unaltered (FULL RANGE) or has a high-pass filter (HI PASS) applied to it. If HI PASS is selected, a 120Hz
24dB/Octave high-pass filter is applied to the signal coming out of the THRU connector. Engaging the high-
pass filter allows for a smooth transition between the subwoofer and full-range speaker that is connected to
the output connector.
3. PWR/STBY LED – This LED illuminates when the “Power Switch” has been turned to the on position. It will
illuminate BLUE when the system has power and is ready to pass audio. It will illuminate RED when the
system is in power save mode and not passing audio.
4. FRONT LED – This push button allows you to turn on/off the Power LED on the front of the speaker. The
front LED will illuminate BLUE when the system has power and is ready to pass audio. When the front LED
turn RED that means the system is in power save mode and not passing audio.
5. SIGNAL Indicator – There is one GREEN LED that will illuminate when signal is present.
6. LIMIT Indicator – There is one YELLOW LED indicator that will illuminate when peak output has been
reached and the DSP limiter is acting.
7. GAIN Knob – This gain knob is for setting the input level. The 12 o’clock position is a good starting point for
most uses. Once the full-range system has been connected the level can be varied to match and deliver the
desired balance.
8. XLR Inputs – Female balanced XLR and 1/4 inch phone jack combo input connectors.
9. THRU Connectors – Male balanced XLR output connector. This connector provides a FULL RANGE or HI
PASS signal depending on the setting of the PASS THRU button. In addition to connecting a full-range
system to the output, it’s also possible to daisy chain subwoofers together.
19
TROUBLESHOOTING
Symptom
Likely Cause
What to do
Speaker not connected
to active AC power
Verify that speaker is connected and that
circuit is on. Switch on power and verify
that illuminated logo is on.
• Re-seat the power cable at both ends.
• Substitute a known-good power cable.
No sound
Speaker power cable
is faulty or improperly
connected
Blown fuse
• Replace the fuse with the specified value
and type.
• Take your speaker to a competent
service center.
No sound, speaker is
connected to working AC
power but won’t come on.
Signal source (mixer,
instrument, etc.) is not
active
• Check VU meters on the source mixer.
• Verify that the CD/MP3 is playing.
• Use headphones to verify that the
instrument is actually sending an audio signal.
• Disconnect and re-seat signal cables.
• Replace suspected cable with a
known-good cable.
No sound.
Speaker comes on.
Faulty cables and
connections
Microphone requires 48V
phantom power
The PRX700 speakers do not supply
phantom power. Switch to a dynamic
microphone, use a battery in the microphone
(if possible), use an external phantom power
Faulty microphone cable supply. Check cable.
No sound with microphone
connected directly to the
MIC input.
Faulty microphone cable
Excessive input signal,
trying to exceed the
capabilities of
Signal sounds distorted
and very loud, OVERLOAD
light is lit most of the time.
• Reduce the output level of the source.
• Turn down the level controls on the speaker.
the speakers
Review the Owner’s Manual for your system setup
and adjust controls as needed.
• Input sensitivity (gain)
Signal sounds distorted
even at moderate volumes,
OVERLOAD light is not lit.
Mixer or other source
is overdriven (clipping)
• Check gain structure of signal chain
Disconnect the devices that are connected to
your speaker one at a time. If the noise goes
away, the problem is with the source or the
connecting cable.
Noise or hiss heard at
output
Noisy Source Device
20
Improper A/C ground or
faulty equipment
connected to mixer input the faulty equipment for troubleshooting help.
Disconnect or mute channels one at a time to
isolate the problem. Refer to the owner’s manual of
Hum or Buzz that
increases or decreases
when the mixer level
controls are moved
Faulty cable between
source equipment and
mixer
Substitute a known-good cable for the suspected
faulty cable.
• “Telescope” the audio ground by using an XLR/F
Improper A/C grounding,
ground loops
to XLR/M adapter on one end.
• Re-route audio cable away from AC power and
lighting cables.
• Use the balanced outputs (if available) of your
mixer or source equipment to drive your
EON speakers.
Excessively long
Hum or Buzz
unbalanced cable run
• Use a “DI” (direct injection) box to convert
your unbalanced equipment output to a
balanced output.
Review the Owner’s Manual for your system
setup and adjust controls as needed.
• Input sensitivity (gain)
Improper system gain
structure
Microphones are pointed Move the speakers so they do not point to the
into the speakers
microphone’s pickup pattern.
Speakers feedback and
howl when the microphone
volume is turned up
Equalizer settings are
incorrect
Locate the feedback frequency and reduce it
using the mixer EQ or an external equalizer.
Reduce the gain at the mixer and move the
microphone closer to the sound source.
Excessive gain
Too much low frequencies
when playing back
prerecorded music
Recorded music
with excessive
low frequencies
Switch the EQ switch to “flat.”
Section 7: Connection Types
21
CONTACT INFORMATION
Mailing Address:
JBL Professional
8500 Balboa Blvd.
Northridge, CA 91329
Shipping Address:
JBL Professional
8500 Balboa Blvd., Dock 15
Northridge, CA 91329
(Do not return product to this address without
first obtaining prior authorization from JBL)
Customer Service:
Monday through Friday
8:00am - 5:00pm
Pacific Coast Time in the U.S.A.
(800) 8JBLPRO (800.852.5776)
On The World Wide Web:
Professional Contacts, Outside the USA:
Contact the JBL Professional Distributor in your area.
A complete list of JBL Professional international distributors
Product Registration:
22
WARRANTY INFORMATION
The JBL Limited Warranty on PRX700 is in effect for three years from the date of the first consumer purchase.
Who Is Protected By This Warranty?
Your JBL Warranty protects the original owner and all subsequent owners so long as: A.) Your JBL product
has been purchased in the Continental United States, Hawaii or Alaska. (This Warranty does not apply to JBL
products purchased elsewhere except for purchases by military outlets. Other purchasers should contact the
local JBL distributor for warranty information.); and B.) The original dated bill of sale is presented whenever
warranty service is required.
What Does The JBL Warranty Cover?
Except as specified below, your JBL Warranty covers all defects in material and workmanship. The following
are not covered: Damage caused by accident, misuse, abuse, product modification or neglect; damage
occurring during shipment; damage resulting from failure to follow instructions contained in your Instruction
Manual; damage resulting from the performance of repairs by someone not authorized by JBL; claims based
upon any misrepresentations by the seller; any JBL product on which the serial number has been defaced,
modified or removed.
Who Pays For What?
JBL will pay all labor and material expenses for all repairs covered by this warranty. Please be sure to save
the original shipping cartons because a charge will be made if replacement cartons are requested. Payment of
shipping charges is discussed in the next section of this warranty.
How To Obtain Warranty Performance
If your JBL product ever needs service, write or telephone us at JBL Incorporated (Attn: Customer Service
Department), 8500 Balboa Boulevard, PO. Box 2200, Northridge, California 91329 (818/893-8411). We may
direct you to an authorized JBL Service Agency or ask you to send your unit to the factory for repair. Either way,
you’ll need to present the original bill of sale to establish the date of purchase. Please do not ship your JBL
product to the factory without prior authorization. If transportation of your JBL product presents any unusual
difficulties, please advise us and we may make special arrangements with you. Otherwise, you are responsible
for transporting your product for repair or arranging for its transportation and for payment of any initial shipping
charges. However, we will pay the return shipping charges if repairs are covered by the warranty.
Limitation of Implied Warranties
ALL IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE LENGTH OF THIS WARRANTY.
EXCLUSION OF CERTAIN DAMAGES
JBL’S LIABILITY IS LIMITED TO THE REPAIR OR REPLACEMENT, AT OUR OPTION, OF ANY DEFECTIVE
PRODUCT AND SHALL NOT INCLUDE INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY KIND. SOME
STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS AND/OR DO NOT
ALLOW THE EXCLUSION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS
AND EXCLUSIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS,
AND YOU MAY ALSO HAVE OTHER RIGHTS, WHICH VARY, FROM STATE TO STATE.
23
|