®
Three-Way High Output
Indoor/Outdoor Monitor Speaker
Control 30
Professional Series
Key Features:
᭤
Extended bandwidth, extremely smooth
frequency response.
᭤
Fully outdoor-capable design, featuring
WeatherMax™ multi-layer grille.
᭤
᭤
120° x 110° HF coverage.
150 Watt transformer for 70V or 100V
lines, with 4 thru.
Ω
®
᭤
᭤
SonicGuard overload protection.
®
250 mm (10 in) fiberglass/Kevlar cone LF
woofer, with neodymium magnet coaxial
125 mm (5 in) anodized aluminum cone
MR, and 25 mm (1 in) titanium diaphragm
compression driver.
®
᭤
᭤
Includes InvisiBall mounting hardware,
plus ten 6 mm attachment points for sus-
pension and optional U-bracket.
Sealed input panel cover and screw-down
input terminals.
Applications
Specifications:
The Control 30 utilizes high power compo-
nents, computer optimized horn and coaxial
component design, patent-pending cabinet manu-
facturing techniques, and a complex network to
achieve smooth high fidelity performance,
extended bandwidth and well-controlled, defined
coverage from a compact loudspeaker.
1
Frequency Range (-10 dB) : 38 Hz – 17 kHz
1
Frequency Response ( 3 dB) : 40 Hz – 16 kHz
2
100 Hr Power Capacity : 500 Watts Continuous Program Power
250 Watts Continuous IEC Pink Noise
3
Maximum SPL @ 1m : Short-Term: 123 dB; Long-Term: 117 dB
Nominal Sensitivity : 93 dB, 2.83V @ 1m (3.3 ft)
Nominal Coverage Angle : 120° H x 110° V
4
5
A symmetrical mid-high frequency horn allows
use of the speaker in either vertical or horizontal
orientation. Smooth frequency response and
cone-midrange performance ensures excellent
sound character throughout the frequency band,
over the entire listening area.
The top-quality line distribution transformer,
designed for minimal insertion loss and reduced
saturation, allows use of either 70V or 100V dis-
tributed speaker lines. In bypass position, the
8 ohm impedance allows use of multiple speak-
ers on a loudspeaker line.
The included InvisiBall mounting method is
simple to install, aims easily and provides a high
degree of theft deterrence. InvisiBall allows hori-
zontal rotation of up to 41° off-axis and vertical
rotation of up to 36° (horn end inward) or 23°
(woofer end inward). Attachment points for the
optional MTC-30UB (-WH) U-bracket allows for
compact installation and is particularly useful for
low profile underbalcony applications.
Directivity Factor (Q): 5.2, averaged 500 Hz to 10 kHz
Directivity Index (DI): 7.1 dB, averaged 500 Hz to 10 kHz
Nominal Impedance: 4 ohms
Crossover Type: 3rd order Low Pass LF, 2nd order High Pass/3rd order Low Pass MF,
3rd order High Pass, HF, plus conjugate shaping circuitry.
Transformer Taps: 70V: 150W, 75W, 38W, 19W
100V: 150W, 75W, 38W
Thru Position: 4Ω nominal
Recommended High-Pass: See Chart
Transducers:
®
Low Frequency: 250 mm (10 in) fiberglass/Kevlar cone with pure butyl rubber sur-
round, 50 mm (2 in) voice coil on fiberglass former, neodymium magnet
Mid Frequency: 125 mm (5 in) anodized aluminum cone with EPDM rubber
(Terpolymer of Ethylene and Propylene) surround, 25 mm (1 in)
voice coil on fiberglass former
High Frequency: 25 mm (1 in) compression driver, pure titanium diaphragm with
patented JBL diamond surround
Physical:
Enclosure Material: High Impact PolyStyrene (HIPS) with 10% glass fill plus patent-
pending internal 5 mm foamed polyurethane secondary mold
Grille: Thermoset composite coated steel, WeatherMax multi-layer foam
Overload Protection: SonicGuard full range power limiting to protect network and trans-
ducers.
Weather resistance has been maximized. The
neodymium magnet LF woofer has a fiberglass
and Kevlar composite cone, the surround is pure
butyl rubber, and the basket is rear loaded to
minimize exposure. The MR cone of the coaxial
mid-high driver is anodized aluminum with a for-
mulation EPDM rubber surround, and the HF
compression driver’s diaphragm is pure titanium.
The coaxial component is protected by an
acoustically transparent screen. The grille is ther-
moset composite coated and stands up very well
to UV as well as humidity. The grille is backed
with our WeatherMax multi-layer foam, which
prevents the direct incursion of water. Nickel/zinc
rust-resistant terminals ensure a secure input con-
nection. An MTC-PC2 sealed-entrance cover is
included to further protect the speaker’s termi-
nals.
Environmental: IEC 529 IP-X5 rating. Exceeds Mil Spec 810 for humidity, salt spray,
temperature & UV. Passes Mil-Std-202F for salt spray.
Termination: Screw-down terminal strip, zinc plated copper base, nickel plated
metal screws/washers. Accepts up to 9 mm outside 4 mm inside open
2
lug (#6, #8 or #10 lug), plus bare wire (up to 12 AWG/2.5 mm ).
Safety Agency Rating: Transformer is listed per UL1876
Colors: Black or white (-WH)
Dimensions (H x W x D): 593 x 372 x 345 mm (23.3 x 14.6 x 13.5 in)
Weight (ea): 18.9 kg (42 lb)
Shipping Weight (ea): 20.3 kg (45 lb)
Included Accessories: 1 pc MTC-PC2 input panel cover, InvisiBall mounting base, 6 mm x
305 mm InvisiBall Hex wrench.
Optional Accessories: MTC-30CM (-WH) to install speaker down from the ceiling.
MTC-30UB (-WH) U-Bracket
1
In Half Space
2
Continuous Pink Noise rating is IEC-shaped pink noise with a 6 dB crest factor for 100 hours continuously. Continuous
Program Power is defined as 3 dB above the Continuous Pink Noise Rating and is a conservative expression of the system’s
ability to handle normal speech and music program material.
Calculated from sensitivity and power handling, exclusive of power compression.
Half-space, averaged 100 Hz to 10 kHz
3
JBL’s exclusive SonicGuard overload protection
is virtually inaudible to the listener, ensuring reli-
ability while providing full fidelity sound.
Available in black or white (-WH), the cabinet
will accept a variety of paints to match any
décor.
4
5
500 Hz to 10 kHz
JBL continually engages in research related to product improvement. Changes introduced into existing products without notice
are an expression of that philosophy.
Horizontal 1/3 Octave Polars
Architectural Specifications:
The loudspeaker shall consist of a 250 mm (10 in) low frequency
transducer, a coaxial 125 mm (5 in) mid frequency transducer with a
25 mm (1 in) compression driver, and frequency dividing network. The
low frequency driver’s voice coil shall be 50 mm (2 in) in diameter and
the mid frequency driver’s voice coil shall be 25 mm (1 in) in diameter.
Performance specifications of a typical unit shall be as follows:
Usable frequency response shall extend from 38 Hz to 17 kHz (10 dB
below rated sensitivity, half-space, no external equalization). Rated
power shall be at least 500 watts continuous program power for 100
continuous hours duration (defined as 3 dB above a test signal of fil-
tered random pink noise conforming to IEC268-5). Measured sensitivity
shall be at least 93 dB-SPL (at 1m [3.3 ft] with 2.83V input, avg. 100 Hz
to 10 kHz).
The input shall be switchable for use either at nominal 4 ohms, or
on a 70.7V or 100V distributed speaker line via built-in transformer.
Selectable taps shall nominally be 150W, 75W, or 38W on a 70.7V or
100V distributed line, plus 19W on 70.7V line only.
The system shall be protected against damage from occasional over-
powering via full range limiting, which shall be inaudible during
activation. The coaxial mid-high driver shall be horn loaded to cover
120 degrees horizontal by 110 degrees vertical with a high degree of
accuracy.
The cabinet shall be molded High Impact PolyStyrene (HIPS) with
ten percent glass fill, and a 5 mm internal foamed polyurethane
secondary mold. The grille shall be backed by multi-layer foam and be
secured via screws to keep it in place when facing downward. The
cabinet and grille shall be paintable.
The low frequency transducer shall have a neodymium magnet, a
®
cone of woven fiberglass and Kevlar and butyl rubber surround, with
the frame protected from direct weather exposure. The mid frequency
transducer element of the coaxial mid-high driver shall have an
anodized aluminum cone with an EPDM rubber (a Terpolymer of
Ethylene and Propylene) surround, with the frame protected from
direct weather exposure. The compression driver shall be constructed
with a titanium diaphragm for weather resistance. The coaxial mid-high
driver shall be protected with a secondary acoustically transparent
screen. The system shall withstand Mil Spec 810 testing with specified
durations with no effect on its acoustical performance or structural
integrity; salt spray (method 509.3), temperature (method 501.3 and
502.3), humidity (method 507.3) and ultraviolet (method 505.3).
Further, it shall pass Mil-Std-202F (method 101D) for salt spray. They
system shall have an IEC 529 splashproof rating of IP-X5.
For theft deterrence, the installation access area shall be hidden
behind a snap-out cover on the front grille. The included ball mecha-
nism shall be internal to the cabinet. The cabinet shall have ten (10)
6 mm mounting points including 3 on each side and 3 on top and
bottom and an accessory U-bracket shall be available. The grille logo
shall be rotatable for proper orientation with loudspeaker mounted
horizontally or vertically.
The external wiring connectors shall be screw-down terminals.
Overall cabinet dimensions shall be no greater than 593 high x
372 mm wide x 345 mm deep (23.3 x 14.6 x 13.5 in) and shall weigh
no more than 18.9 kg (42 lb). The finish shall be lightly textured black
or white.
The system shall be the JBL Model Control 30 (or Control 30-WH)
®
with included InvisiBall (mounting system).
᭤ Control 30 Three-Way High Output Indoor/Outdoor Monitor Speaker
Vertical 1/3 Octave Polars
High-Pass Frequency Recommendations
The line-matching transformer in the Control 30 has
been designed to minimize saturation; however, it is rec-
ommended that the system be high-passed to prevent
very low-frequency content from overloading the trans-
former and/or the driving amplifier at high signal levels.
The high-pass requirements vary according to the tap
settings and number of speakers connected in parallel.
The following chart will eliminate risk of saturation,
even at full voltage (70V or 100V) peaks. Reducing the
drive voltage will enable a corresponding reduction of
high-pass frequency (24 dB/octave high-pass slope).
High Pass Recommendations for Control 30
1 or 2 speakers
30 Hz
3 or more speakers
35 Hz
19 Watt Tap
38 Watt Tap
75 Watt Tap
150 Watt Tap
4 Ohm Setting
35 Hz
60 Hz
80 Hz
40 Hz
70 Hz
100 Hz
No High-Pass required
JBL Professional
8500 Balboa Boulevard, P.O. Box 2200
Northridge, California 91329 U.S.A.
SS Control 30
CRP 5M
07/07
A Harman International Company
© Copyright 2007 JBL Professional
|