DOUBLE CASSETTE DECK
-
TD W354
B/J
Area suffix
B .................... U.K.
J .....................U.S.A.
DOLBY B-C NR HX PRO
TD-W354 DOUBLE CASSETTE DECK
DOLBY B-C NR HX PRO
TD-W354 DOUBLE CASSETTE DECK
STANDBY
STANDBY
INPUT LEVEL
5
INPUT LEVEL
5
COUNTER RESET
COMPU CAL COUNTER RESET
COUNTER RESET
COMPU CAL COUNTER RESET
4
6
4
6
3
1
7
3
1
7
AUTO REVERSE
PITCH CONTROL
COMPU CALIBRATION
B
REC/PLAYBACK
AUTO REVERSE
PITCH CONTROL
COMPU CALIBRATION
AUTO REVERSE
A
A
2
8
B
PLAYBACK
2
8
AUTO REVERSE
PLAYBACK
REC/PLAYBACK
MUSIC SCAN
PLAY
MUSIC SCAN
PLAY
MUSIC SCAN
PLAY
MUSIC SCAN
PLAY
9
9
COMPULINK
Component
COMPULINK
Component
MIN
MAX
PITCH CONTROL
MIX LEVEL
MIN
MAX
PITCH CONTROL
MIX LEVEL
MIC
PHONES
MIC
PHONES
DOLBY NR
REVERSEA
B
SYNCHRO DUBBING
REC/REC MUTE PAUSE
POWER
DOLBY NR REVERSEA
B
SYNCHRO DUBBING
NORM SPEED HIGH SPEED
POWER
REC/REC MUTE PAUSE
B
C
NORM SPEED HIGH SPEED
MODE
B
C
MODE
SLOW
FAST
MIN
MAX
SLOW
FAST
MIN
MAX
DECK
A
DECK
A
ON
OFF
STANDBY / ON
(B version)
(J version)
INSTRUCTIONS
For Customer Use:
Enter below the Model No. and Serial No.
which are located on the rear of the cabinet.
Retain this information for future reference.
Model No.
Serial No.
IMPORTANT (In the United Kingdom)
Mains Supply (AC 230 V z, 50 Hz only)
RISK OF ELECTRIC SHOCK
DO NOT OPEN
DO NOT cut off the mains plug from this equipment. If the
plug fitted is not suitable for the power points in your home or
the cable is too short to reach a power point, then obtain an
appropriate safety approved extension lead or consult your
dealer.
CAUTION
‘‘TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK)
NO USER SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.’’
BE SURE to replace the fuse only with an identical approved
type, as originally fitted and to replace the fuse cover.
If nonetheless the mains plug is cut off ensure to remove the
fuse and dispose of the plug immediately, to avoid a possible
shock hazard by inadvertent connection to the mains supply.
The lightning flash with arrowhead symbol, within
an equilateral triangle, is intended to alert the
user to the presence of uninsulated ‘‘dangerous
voltage’’ within the product’s enclosure that may
be of sufficient magnitude to constitute a risk of
electric shock to persons.
DO NOT make any connection to the terminal which is
marked with the letter E or by the safety earth symbol or
coloured green or green-and-yellow.
The wires in the mains lead on this product are coloured in
accordance with the following code:
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and maintenance
(servicing) instructions in the literature
accompanying the appliance.
Blue to N
(Neutral) or Black
Brown to L
(Live) or Red
As these colours may not correspond with the coloured mark-
ings identifying the terminals in your plug proceed as follows:
The wire which is coloured blue must be connected to the
terminal which is marked with the letter N or coloured black.
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOIS-
TURE.
The wire which is coloured brown must be connected to the
terminal which is marked with the letter L or coloured red.
IF IN DOUBT-CONSULT A COMPETENT ELECTRICIAN.
Please study this instruction manual carefully before starting
to operate the unit, in order to use the unit correctly. We take
no responsibility for any problems resulting from misuse of
this unit by operating this equipment other than instructed in
this manual.
WARNING (In the United Kingdom)
Pre-recorded tapes, records or discs should not be
re-recorded without the consent of the owners of copyright in
the sound recording and in any copyright musical or literary
work embodied in that recording as this constitutes an
infringement of copyright.
INFORMATION (FOR U.S.A.)
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications.
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of
the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician
for help.
However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
– 2 –
INTRODUCTION
Thank you for purchasing a JVC product. Read this instruction
book carefully before operating to be sure of getting optimum
performance and longer service life from the unit.
This product can be combinated with a DDRP (DYNAMICS
DETECTION RECORDING PROCESSOR) system (compact
disc player + cassette deck, etc.) to enable setting the opti-
mum recording level automatically. Refer to these instruc-
tions for details.
CONTENTS
Features .................................................................................... 3
Auto reverse operation ............................................................. 3
Cautions .................................................................................... 3
Connections .............................................................................. 5
Cassette loading ....................................................................... 5
Names of parts and their functions .......................................... 6
Playback ................................................................................... 7
Multi music scan ....................................................................... 8
Recording ................................................................................. 8
Compu link control system ..................................................... 11
Dubbing .................................................................................. 12
Maintenance ........................................................................... 13
Troubleshooting ...................................................................... 14
Specifications .......................................................................... 15
AUTO REVERSE OPERATION
The auto reverse operation of this unit turns the tape transport
over to the reverse of forward direction automatically when the
tape reaches its end during recording or playback.
•
Because of cassette shell construction, a tape recorded in the
forward direction should be played back in the same direction
to obtain stable sound reproduction.
During recording, auto reverse can be activated only from the
•
forward to the reverse direction. For good sound quality and to
avoid accidental erasure of previously recorded material,
always start recording with the side A of the tape facing out.
FEATURES
1. Double auto-reverse mechanism for recording/playback
in deck B and playback in deck A
CAUTIONS
2. The COMPU CAL function automatically sets the
record/playback flat frequency characteristics and opti-
mal record/playback tape sensitivity for bringing out
maximum tape performance.
1. Prevention of Electric Shocks, Fire Hazards and Damage
1) Even when the POWER switch is set to STANDBY, a very
small current will flow. To save power and for safety when
not using the unit for an extended period of time, disconnect
the power cord from the household AC outlet. (for the J ver-
sion)
3. Full logic mechanism
4. Dolby* HX PRO headroom extension
5. Dolby B & C noise reduction system
6. DDRP (Dynamics Detection Recording Processor) com-
patibility
The DDRP function is possible only when used with a suit-
able JVC CD player.
7. 2-color FL peak level indicator
Set the
POWER switch to the OFF position when not in
use. (for the B version)
2) Do not handle the power cord with wet hands.
3) When unplugging from the wall outlet, always grasp and pull
the plug, not the power cord.
4) Consult your nearest dealer when damage, disconnection, or
contact failure is found with the cord.
8. Digital tape counter respectively for deck A and deck B
9. Synchro start (normal-/high-speed) dubbing
10. Auto tape select mechanism (decks A and B)
11. Multi music scan mechanism for either direction
‘‘Under License of Staar S.A., Brussels, Belgium’’
12. PITCH control
5) Do not bend the cord sharply, or pull or twist it.
6) Do not modify the power cord in any manner.
7) Do not remove screws to disassemble the unit and do not
touch anything inside the unit.
8) AC power cord (For the J version only)
The AC power cord of this unit has certain one-way direction
connections to prevent electric shock. Refer to the illustration
for correct connection. (Fig. 1)
13. Microphone mixing is possible
14. COMPU LINK-3 compatible
Dolby noise reduction and HX Pro headroom extension
manufactured under license from Dolby Laboratories
Licensing Corporation. HX Pro originated by Bang & Olufsen.
*
*
‘‘DOLBY’’, the double-D symbol
and ‘‘HX PRO’’ are trade-
marks of Dolby Laboratories Licensing Corporation.
Fig. 1
COMPU LINK control system is the convenient system using
COMPU LINK-3/SYNCHRO terminals on the rear panel.
(See page 5 and 11.)
(For CANADA)
CAUTION
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE
OF PLUG TO WIDE SLOT, FULLY INSERT.
– 3 –
Side ‘‘A’’
(Pour le CANADA)
ATTENTION
POUR EVITER LES CHOCS ELECTRIQUES, INTRODUIRE
LA LAME LA PLUS LARGE DE LA FICHE DANS LA
BORNE CORRESPONDANTE DE LA PRISE ET POUSSER
JUSQU’AU FOND.
Tab ‘‘B’’
Side ‘‘B’’
Tab ‘‘A’’
9) Do not insert any metallic objects into the unit.
10)Unplug the power cord when there is a possibility of light-
ning.
11) If water gets inside the unit, unplug the power cord from the
outlet and consult your dealer.
12)Do not block the ventilation holes of the unit so that heat can
escape. Do not install the unit in a badly ventilated place.
13)Be sure to unplug the power cord from the outlet when going
out or when the unit is not in use for an extended period of
time.
Adhesive tape
Fig. 3
2. Installation
1) Avoid placing the unit on or adjacent to an amplifier, to pre-
vent hum from being produced by some types of amplifiers.
Move the unit to a place not affected by the amplifier. Keep
the unit as far as possible from a TV set.
4) Do not store cassette tapes where there is a magnetic field
(e.g. near a TV, etc.) or in a place subject to high tempera-
tures or humidity.
2) Avoid installing the unit in a location subject to ambient tem-
peratures exceeding 40 °C (104 °F) (e.g. direct sunlight,
near heaters, etc.) or less than 0 °C (32 °F), excessive
humidity, dust or vibrations.
3) If this set is moved suddenly from a cold place (0 °C) to a
warm place, it may not function properly because of moisture
generated inside the unit. The unit will function properly
30 minutes after being moved.
5. Auto tape select mechanism (decks A and B)
This deck has an Auto Tape Select mechanism which distin-
guishes between different types of tape from holes in the
cassette. After the type of tape has been detected, bias and
equalization are set to be suitable for the tape.
•
Cassettes with the detection holes:
Metal tape (EQ: 70µs) ........................................ Type IV
CrO2 (chrome) tape (EQ: 70µs) .......................... Type II
3. Cleaning the cabinet
Never use benzine or thinner for cabinet cleaning as they may
damage the surface finish.
•
Cassettes without the detection holes:
Normal tape (EQ: 120µs) ..................................... Type I
4. Cassette tape
Some earlier types of metal and CrO2 (chrome) tapes may
not be provided with the detection holes. Avoid using such
tapes, since correct equalization characteristics cannot be
obtained. Also do not use ferrochrome tapes whose charac-
teristics do not match this unit.
1) Loose tape may become tangled in the tape transport
mechanism. Remove slack by winding the tape with a pen-
cil.
(Fig. 2)
CrO2 tape detection
holes
Fig. 2
Metal tape detection holes
Turn the pencil to tighten the tape.
2) The use of C-120 (120 minutes turn around) or thinner tape
is not recommended, since characteristic deterioration may
occur.
3) To prevent recordings from being erased accidentally,
remove the tab(s) with a screwdriver. Reseal the slots with
adhesive tape to erase and re-record after the tabs have
been broken off.
6. Operations
1) Noise may be generated if the
switched OFF with the deck set to playback or recording
mode. Before switching the POWER switch OFF, confirm
POWER switch is
that the (stop) button has been pressed. (B version)
2) Many operations of this unit are performed under the control
of a microcomputer. Use the unit only after carefully studying
the descriptions and cautions in each item. If operations are
done incorrectly, the unit may stop functioning correctly. If
this happens, for the J version, unplug the power cord and
for the B version, set the
POWER switch to
OFF, so
that the unit can function correctly.
– 4 –
CONNECTIONS
•
Do not switch the power on until all the connections are com-
pleted.
Insert the plugs firmly, or poor contact will result, causing
noise.
When the pin-plug cords are employed, always connect the
white plug to the left channel terminal. This helps to avoid
reversed connections.
2. Remote cable connection for COMPU LINK
By connecting a remote cable, COMPU LINK functions (auto-
•
•
matic power on/STANDBY, automatic source selection, syn-
chronized recording and DDRP recording) can be performed.
In this time the provided pin-plug cords must be also con-
nected.
•
•
When making synchronized recording with a CD player, con-
•
nect the remote cable to the COMPU LINK-1/SYNCHRO or
COMPU LINK-3/SYNCHRO jacks.
When using the Compu Link Control System version 3, do not
connect the power cord to the SWITCHED AC OUTLET of an
amplifier or receiver. In the
POWER switch ON. Otherwise, the automatic power on/
STANDBY function cannot be carried out.
B
version, turn the deck
Notes:
1. When making synchronized recordings, only a single deck
should be connected to the amplifier.
2. If a component is not a JVC COMPU LINK component,
bypass it when making the remote cable connections.
3. This deck can be connected with an amplifier and a CD
player which have the COMPU LINK-1/SYNCHRO jacks for
COMPU LINK performance. (See page 11 for details.)
1. Connection to a stereo amplifier
Note:
When installing the deck, be sure to install at a distance from
your amplifier. If they are stacked, noise (hum) may occur.
CASSETTE LOADING
•
1. Press the
(eject) button to open the cassette holder.
Setting the
POWER switch to OFF during playback or
2. Load a cassette as shown.
recording may cause a malfunction. Always stop playback
3. Press the cassette holder to close it. Be sure to obtain the
click sound to close the holder securely.
before setting the
POWER switch to OFF.
Notes for the B version:
A
•
If the
POWER switch is set to OFF while the tape is mov-
ing, you might not be able to remove the cassette. If this hap-
pens, switch the power on again before attempting to remove
the cassette.
Load the cassette with the
tape-exposed edge down.
AUTO REVERSE
– 5 –
NAMES OF PARTS AND THEIR FUNCTIONS
9
1
3
4
5
6
7
8
0
q
w
2
1
DOLBY B-C NR HX PRO
TD-W354 DOUBLE CASSETTE DECK
TD-W354 DOU
STANDBY
INPUT LEVEL
5
COUNTER RESET
COUNTER RESET
COMPU CAL
4
6
3
1
7
AUTO REVERSE
PITCH CONTROL
COMPU CALIBRATION
AUTO REVERSE
AUTO
PITCH C
A
A
B
2
8
PLAYBACK
REC/PLAYBACK
PLAYBACK
MUSIC SCAN
MUSIC SCAN
9
COMPULINK
Component
PLAY
COMPULINK
Component
PLAY
MIN
MAX
MIC
MIX LEVEL
PITCH CONTROL
PHONES
A
B
SYNCHRO DUBBING
DOLBY NR REVERSE
REC/REC MUTE PAUSE
POWER
POWER
B
C
MODE
NORM SPEED HIGH SPEED
SLOW
FAST
MIN
MAX
DECK
A
ON
OFF
STANDBY / ON
(B version)
(J version)
ON
e
r t
y
u
o
p
a
i
1
POWER switch (
OFF) (B version)
6 Dubbing mode indicators
‘‘DUBBING >’’
: Lights when in the normal-speed dub-
bing mode.
POWER switch (On/Standby) (J version)
switch (STANDBY/ON) (B version)
3 Cassette holder (deck A)
2
‘‘DUBBING >>’’ : Lights when in the high-speed dub-
bing mode.
7 CONT
4 Cassette operation buttons (deck A)
: Lights when the unit is in the continu-
ous play mode.
: Press to wind the tape quickly from right to left.
: Press to wind the tape quickly from left to right.
: Press to play the tape.
8 Mechanism mode indicators (deck B)
PLAY
: Lights when the unit is in the playback
and record modes.
: Indicates the direction of tape travel.
: Lights when the unit is in the record
and record-pause modes; blinks dur-
ing record muting.
PLAY
(stop)
: Press to stop the tape.
,
: Press to change the direction of tape travel.
REC
(direction)
(eject) button (deck A)
5
: Pause indicator
6 Power STANDBY indicator
: This lights when rewinding the tape
from left to right.
: This lights when rewinding the tape
from right to left.
Lights when in the power standby mode.
7 COUNTER RESET button (deck A)
Press this button to set the digital counter to ‘‘00 00’’.
Even if the
(STANDBY/ON) or POWER switch is set to
9
: Indicates reverse mode.
9 COMPU CAL button and indicator
STANDBY, the counter value at that time is stored in
Press this button to automatically set the recording charac-
teristics with the COMPU CAL function. (See page 9.)
0 COUNTER RESET button (deck B)
memory.
8 Indicators
1 DDRP indicator
2 Peak level indicator
q
(eject) button (deck B)
These indicators light according to the level of the signal
being recorded or the level of the signal recorded on the
tape.
w Cassette holder (deck B)
e PHONES jack
Connects headphones (with an impedance of 8 Ω to 1 kΩ).
r INPUT LEVEL control
t PITCH CONTROL (deck A)
Note:
0 dB
0 VU
: IEC (DIN) STANDARD LEVEL (250 nWb/m)
: Signal level at 160 nWb/m
3 HX PRO indicator
4 Digital counter
Varies the tape speed in deck A in the range of about ±10%.
However, it cannot change the tape speed in the high-speed
dubbing.
Turning it counterclockwise toward ‘‘SLOW’’ causes the tape
speed to decrease while turning clockwise toward ‘‘FAST’’
causes it to increase. The center click position is for the
standard speed. (See page 8.)
The counter reading increases while the tape is running
from left to right and decreases when it is running from
right to left. In the Multi Music Scan mode when the
(or
) button is pressed, the number of tunes
which will be skipped is displayed.
5 Mechanism mode indicators (deck A)
: This lights when rewinding the tape
from left to right.
y Mixing microphone level control
Adjusts the microphone input level.
u MIX MIC jack
: This lights when rewinding the tape
from right to left.
: This lights when in the playback.
: Indicates the direction of tape travel.
PLAY
,
Connects a microphone (with an impedance of 600 Ω to
10 kΩ) to this jack.
Sounds from the microphone are monaural.
– 6 –
PLAYBACK
8
1
POWER
POWER
1
2
3
STANON
O
OFF
(B version)
(J version)
2
A
4
5
6
7
8
4
9
3
5
4
6
DOLBY NR
B
C
i Cassette operation buttons (deck B)
: Press to wind the tape quickly from right
to left.
: Press to wind the tape quickly from left to
right.
REVERSE
MODE
(stop)
: Press to stop the tape. Also press to stop
both decks simultaneously during dub-
bing.
PLAY
PLAY
REC/
REC MUTE
: Press to start playback/recording.
: Press the PLAY button while pressing
this button to start recording, and press
to leave an appropriate non-recorded
section. (See page 10.)
Playback of deck A
Operate in the order of the numbers in the illustration.
1 Turn the power on.
2 Load a prerecorded cassette with side A facing out.
3 Select the side to be played back.
PAUSE
: Press to stop the tape temporarily during
recording and playback. Press the PLAY
button to release the pause mode.
Side A... Forward direction (PLAY
)
Side B... Reverse direction ( PLAY)
4 Press the DOLBY NR button to set the same setting as when
the tape was recorded.
(direction) : Press to change the direction of tape
travel.
5 Select the REVERSE MODE.
o DOLBY NR button and indicators
6 Press the PLAY button of deck A to start playback.
When the deck contains a tape, it can be played back by just
pressing the PLAY button in the B version only when the
•
Set to B or C for recording using the Dolby NR system or for
playing back a tape that was recorded using the Dolby NR
system. Each time the button is pressed the NR mode
changes and the indicator lights. (Dolby B NR -> Dolby C NR
-> NR OFF -> Dolby B NR ...)
POWER switch is set to ON and the
switch is at
STANDBY. In the J version, the tape can be played back by
pressing the PLAY button only when the POWER switch is set
to STANDBY.
Set to OFF when the Dolby NR system is not used.
p REVERSE MODE button
Playback of deck B
Perform steps 2 to 6 of the above procedure for deck B.
Select the single side or full record/playback mode, or the
continuous play mode. Each time the button is pressed the
Microphone mixing during playback
By connecting a microphone, microphone mixing with playback
mode changes. (
->
->
->
...) The current mode
sound from deck A or deck B is possible.
can be checked with the mechanism mode indicator.
: For single-side recording or playback.
: To play or record both sides A and B.
: To play sides A and B continuously.
Continuous play
First press the REVERSE MODE button to set to
.
Load cassette tapes in both decks and press the PLAY button of
the deck to be played first for continuous play of both decks.
a A
B SYNCHRO DUBBING buttons
•
At this time, the CONT indicator lights in the multimode display.
Press to dub from deck A to deck B.
•
When the tape in the deck which plays first reaches the end of
side B (in the reverse direction), it automatically switches to the
forward direction and enters the standby mode. At the same
time, the other deck starts playback. These operations con-
tinue between decks A and B.
NORM SPEED : Press to perform normal-speed dubbing.
HIGH SPEED : Press to perform high-speed dubbing.
•
•
While one deck is playing back, the cassette in the other one
can be replaced. This is convenient for long-time playback of
background music.
Note:
•
Use tapes recorded using the same NR mode in decks A and
B.
– 7 –
PITCH CONTROL (deck A)
RECORDING
It is possible to vary the tape speed in deck A in the range of
about ±10% in the playback mode. The center click position is
for the standard tape speed.
Deck B only
Operate in the order of the numbers in the illustration.
•
Make sure the safety tab of the cassette has not been broken
off.
MULTI MUSIC SCAN
It should be noted that it may be unlawful to re-record pre-
recorded tapes, records, or discs without the consent of the
owner of copyright in the sound or video recording, broadcast
or cable programme and in any literary, dramatic, musical, or
artistic work embodied therein.
•
The multi music scan mechanism of this unit allows you to
quickly locate the beginning of a specific tune (up to 99 tunes
before or after the current tune).
The multi music scan mechanism functions by detecting non-
•
recorded sections between tunes (of more than 4–5 sec.).
The illustration shows the forward direction.
•
1
Example of fast forward scan.
POWER
POWER
PLAY
STANON
O
OFF
(B version)
(J version)
MUSIC SCAN
PLAY
2
3
A
Procedure
1. Press the
2. When more than 2 tunes are to be skipped, after procedure
1 press the (or ) button the number of times you
button during playback.
4
7
5
REVERSE
MODE
DOLBY NR
B
C
want to skip tunes. The number of tunes to be skipped is
displayed in the counter.
•
Relation between Multi Music Scan and REVERSE MODE.
: The multi music scan mechanism operates on one
side of the tape only. If the number set is too high
(more than there are tunes remaining on that side),
the tape stops when the end of the tape is reached.
: It operates continuously through one cycle of the A
and B sides of the tape. If the number set has not
been reached, the tape stops at the end of the B
side. When the head rotates to play side A from B or
B from A, this rotation is counted as one non-
recorded section. When a recorded tune continues
from side A to B, this tune is recorded as two tunes.
6
8
PAUSE
REC/REC MUTE
COMPU CAL
9
0
INPUT LEVEL
5
4
6
3
1
7
COUNTER RESET
PLAY
2
8
In such a case, press the
extra time.
(or
) button one
9
MIN
MAX
Notes:
In the following cases, the mechanism may not operate cor-
rectly. This is not a malfunction; use the mechanism according
to the type of program.
1 Turn the power on.
2 Load a cassette for recording.
•
Tapes with tunes having long pianissimo passages (very quiet
parts) or non-recorded portions during tunes.
Tapes with short non-recorded sections.
3 Press the DOLBY NR button to set to the required setting.
4 Press the REVERSE MODE button to set to the desired set-
ting.
•
5 Select the side to be recorded.
6 Press the COMPU CAL button, if required. (See page 9.)
7 Press the PAUSE button and
REC/REC MUTE button
(record-pause mode).
REC and
indicators light.
8 Adjust the recording level. (See page 10.)
9 Press to ‘‘00 00’’.
0 Press the PLAY button to start recording.
Notes:
•
When the safety tabs are removed from a cassette tape, the
tape cannot be recorded even if you try. Make sure that both
tabs are still in place when performing full recording.
– 8 –
•
•
•
When the tape is played or recorded in the reverse direction
(side B), only side B is played back or recorded and then the
tape stops automatically.
When an error occurs or when COMPU CAL operations are
interrupted, calibration data cannot be stored in the memory. If
settings were previously performed, the previous setting val-
ues are retained.
After confirming items 1) to 3) above and stopping the error
indication if there are no problems, even tapes which experi-
ence errors can be recorded on using either 1 the unit’s pre-
set values or 2 previous setting values. (These are the values
obtained by opening and closing the cassette holder one time.)
* Preset value: a standard value corresponding to each type of
tape, which allows normal recording. (The pre-
DDRP (Dynamics Detection Recording Processor) record-
ing
DDRP recording is performed with suitable JVC CD players and
the recording level adjustment is performed automatically.
Since recording level adjustment is performed automatically for
different types of tape (normal, CrO2 and metal), the adjustment
of INPUT LEVEL control is not required.
set value condition is in effect when the
Read the instruction book of your CD player carefully.
COMPU CAL indicator is unlit.)
Notes:
COMPU CALIBRATION (COMPU CAL) FUNCTION
1. Since COMPU CAL operations record a test tone on tapes,
previously recorded contents will be erased.
•
This unit is equipped with a COMPU CAL function which can
2. Using new tapes and cleaning the heads beforehand are
recommended for optimal COMPU CAL operations.
3. Some variance in characteristics exists even with the same
type of tape made by the same manufacturer. Therefore,
when precise settings are desired, performing COMPU CAL
operations for each recording is recommended.
automatically set the flat frequency characteristics and optimal
tape sensitivity for each tape in approximately 30 seconds.
Calibration data is retained for each tape type (Type I, II or IV).
•
Calibration data set with COMPU CAL is retained even if the
power is turned off (or the power cord is unplugged), and the
previous calibration data for the same type of tape as the new
tape is recalled each time tapes are changed.
Performing COMPU CAL operations again replaces existing
data with the new data.
4. To delete contents set with COMPU CAL, simultaneously
press the
REC/REC MUTE and B deck COUNTER
•
RESET buttons. This deletes the calibration data for the type
of tape currently inserted in the unit. Calibration data for
other tape types is not deleted.
COMPU CAL operation
•
Insert the tape to be recorded and press the COMPU CAL but-
ton. During the operation, ‘‘C’’ → ‘‘CA’’ → ‘‘CAL’’ is displayed in
the tape counter. When the operation finishes, the tape returns
to its starting position, and the COMPU CAL indicator lights.
COMPU CALIBRATION is now finished.
•
Pressing the (stop) button part-way will interrupt the opera-
tions.
•
To recalibrate the unit, press the COMPU CAL button and wait
for the COMPU CAL indicator to go out. Then, press the
COMPU CAL button again.
Note:
If the tape is near its end, it will automatically stop and an error
will be generated during operation. Therefore, be sure to check
the time remaining on the tape (more than 2 minutes in the play
mode) before starting the operations.
COMPU CAL Errors
•
When the COMPU CAL indicator flashes, this indicates a
COMPU CAL error.
Press the (stop) button to stop the error indication.
•
Care should be taken for the following items as they are the
cause of errors.
1) Dirty heads
2) Scratches on the tape surface
-Replace with an undamaged tape.
-Clean the heads.
3) When the tape ends part-way through the operations
-Change the tape position.
4) In rare cases, tapes may have characteristics which fall out-
side the COMPU CAL setting range.
– 9 –
MICROPHONE MIXING DURING RECORDING
B. To leave non-recorded sections of more than 4–5 sec-
onds
By connecting a microphone, microphone mixing during record-
ing is possible by following the recording procedure. Adjust the
microphone input level by setting the record-pause mode and
observing the peak level indicators.
1. Keep the
REC/REC MUTE button pressed continu-
ously as long as you want to make a non-recorded sec-
tion. By releasing the finger from the button after the
above operation, the unit enters the record-pause mode.
2. Press the PLAY button to start recording again.
•
When the record-pause mode is set and the INPUT LEVEL
control is set to MIN, sounds are output only from the micro-
phone, and it can be used as a public address system.
C. To leave non-recorded section of less than 4-seconds
When the undesired section comes during recording....
After the
REC/REC MUTE button is pressed, press the
RECORDING LEVEL ADJUSTMENT
PLAY button before the unit enters the pause mode to start
recording again, or press the PAUSE button to enter the
record-pause mode.
The peak level indicator lights even during record muting
according to the input level which can be heard from the
speakers or headphones so that recording can be resumed at
the exact point on the tape.
Adjust the recording level while observing the peak level indica-
tor indication.
•
For example:
With metal tape
ERASING
When recording on a prerecorded tape, the previous recording
is automatically erased and only the new program is recorded
on the tape.
To erase a tape without making a new recording...
Follow the section ‘‘RECORDING’’ but in step 8, set the INPUT
LEVEL control to MIN.
Because of metal tape’s higher saturation level, it is OK that ‘‘+
2’’ lights occasionally.
With normal or chrome tape
DOLBY NR and DOLBY HX PRO
Dolby NR System
To reduce the hiss inherent in tape recording, use the Dolby NR
System when making recordings. When listening to a tape
recorded with the Dolby NR System, press the DOLBY NR but-
ton to set to B or C according to the system selected in the
recording mode.
It is OK that ‘‘+ 0’’ lights occasionally.
•
When the recording level is too low, the hiss noise inherent in
the tape will be conspicuous.
When the recording level is too high, exceeding the saturation
•
Note:
level, the recording will contain cracking noise and will be dis-
torted.
If ‘‘+ 4’’ lights too often because the recording level is too high,
The sound quality will change if the setting of the DOLBY NR
button is different in recording and playback.
•
the recorded sound may be distorted and seem to be breaking
up. If only ‘‘0’’ lights infrequently, the level is too low and the
recording may contain tape hiss.
Dolby HX PRO headroom extension
When a source which contains many high-frequency compo-
nents is recorded, these high-frequency signals have the same
function as bias and therefore, the effective bias current
changes.
This will result in phenomena such as changes in the level of
low-frequency signal and subsequent distortion and reduction of
the high-frequency saturation level.
Dolby HX PRO headroom extension system controls the bias
current so that the effective bias is constant even when there
are fluctuations in the high-frequency components of the input
signal.
It is best to adjust so that the maximum sound level of the
source to be recorded reaches the very limit of the saturation
level of the tape to be used.
The best level varies depending on the type of music and type
of tape so it is better to make a test recording, using FM music,
records, etc.
AUTOMATIC RECORD MUTING (DECK B)
This greatly improves the high-frequency saturation level while
reducing the low-frequency signal level variations and distortion.
This facility is used to eliminate undesired sections and leave an
appropriate non-recorded section.
•
The dynamic sound recorded with this system sounds the
same even when the tape is played back in a deck that does
not have Dolby HX PRO.
This system automatically works when in recording; however,
A. To leave non-recorded sections of about 4–5 seconds
automatically
•
Dolby HX PRO is not a noise reduction system.
1. When the undesired section comes during recording,
press the
REC/REC MUTE button and release it.
2. The REC indicator flashes and a non-recorded section is
made during record muting operation. About 4–5 sec-
onds later, the tape automatically stops, and the unit
enters the record-pause mode.
3. Press the PLAY button to start recording again.
– 10 –
COMPU LINK CONTROL SYSTEM
The Compu Link Control System controls relative operations
between components automatically and facilitates various
operations.
This is a system originated and developed by JVC for facilitating
various system operations. There are two versions of this sys-
tem; version 1 and 3. (For version 1 components, ‘‘COMPU
LINK-1/SYNCHRO’’ is marked on the rear panel. For version 3
components, ‘‘COMPU LINK-3/SYNCHRO’’ is marked on the
rear panel. This unit belongs to version 3.)
Notes:
•
Synchronized recording or DDRP recording stops automati-
cally when the CD player stops playing.
Synchronized recording does not start except when the record-
•
pause mode is set by simultaneously pressing the
REC/REC MUTE and PAUSE buttons in the stop mode.
To cancel synchronized recording or DDRP recording, press
•
the STOP button of the CD player or cassette deck.
The source is locked to the CD position during synchronized
•
recording or DDRP recording to avoid accidental stops or
switch-over to another component. To switch over the compo-
nents, cancel synchronized recording or DDRP recording first.
The version 3 system controls relative functions between this
unit and an amplifier or receiver, in addition to all of the functions
of version 1.
•
The INPUT LEVEL control does not function during DDRP
recording.
Automatic Power On/STANDBY Function (COMPU LINK-3)
This function is available when an amplifier or receiver having a
COMPU LINK-3/SYNCHRO terminal is connected. For example,
if a deck contains a tape, the deck is turned on automatically
and the tape is played back by only pressing the PLAY button.
When the amplifier or receiver is switched STANDBY, the source
unit is automatically switched STANDBY. (In the B version, it is
necessary to turn the deck
POWER switch ON.)
Automatic Source Selection (COMPU LINK-1, 3)
When the provided remote cables are used for connecting this
unit to other components which have COMPU LINK-1 or
3/SYNCHRO terminals, the switch-over of all system compo-
nents is possible with simple one-touch of the source selector
button of JVC’s amplifier or receiver.
By doing this, the corresponding component will start playing
automatically.
The source select button of the remote control unit or the acti-
vation button of the desired component can be also used for this
purpose. When the components have been switched over, the
previous component will stop playing within five seconds.
Synchronized Recording (COMPU LINK-1, 3)
Synchronized recording refers to the process in which the deck
starts recording in synchronism with the CD player. Perform the
synchronized recording as follows:
1. Set the cassette deck to the record-pause mode in accor-
dance with the recording procedures on page 8.
2. If you want the programmed recording, program the desired
tunes in any order you wish to hear.
3. Press the PLAY/PAUSE button of the CD player. By so
doing, the cassette deck is placed in the record mode and
synchronized with the CD player for recording. Synchronized
recording thus can be made possible.
DDRP (Dynamics Detection Recording Processor) record-
ing
The DDRP function makes possible fully automatic recording
when used with a suitable JVC CD player. When the DDRP but-
ton of a suitable JVC CD player is pressed, the recording level
is first adjusted automatically, then recording starts; it is not nec-
essary to start recording by the normal procedure.
– 11 –
DUBBING
•
•
Synchro dubbing
Operate in the order of the numbers in the illustration.
Before pressing the SYNCHRO DUBBING button
Confirm that deck B is in the stop mode before starting dub-
bing.
1
POWER
POWER
Dubbing and DOLBY NR button
During dubbing, the same NR mode selected for the playback
cassette is applied to the recording cassette, regardless of the
setting of the NR button.
STAN/ ON
O
OFF
(B version)
(J version)
Input level
2
3
4
Recording is performed at the same level as the playback tape
during dubbing regardless of the position of the INPUT LEVEL
control.
A
Microphone mixing during dubbing
By connecting a microphone, microphone mixing during dubbing
is possible with the playback sounds from deck A. Be sure to
perform dubbing at normal speed. When performing microphone
mixing during dubbing, use cassettes recorded with NR OFF
mode for the deck A.
A
Tape editing
1. Press the
5
7
REVERSE
MODE
REC/REC MUTE button when finished dubbing
a tune. Deck B automatically enters the record muting mode
and leaves a non-recorded section of about 4-seconds then
enters the record-paused mode.
COUNTER RESET
2. Press the (stop) button of deck A and search for the next
tune you want by using the
,
or PLAY button. Then
stop the cassette just before the beginning of the tune.
3. Press the same SYNCHRO DUBBING button pressed
before the pause again, and dubbing will start.
6
A
B SYNCHRO DUBBING
NORM SPEED HIGH SPEED
Notes at dubbing
1. Normal-speed dubbing is recommended to obtain good
sound quality.
1 Turn the power on.
2 Insert a prerecorded tape with side A facing out into deck A,
2. Television receivers placed close to the deck may cause
interference on the recorded signal when the deck is used in
the high-speed dubbing mode. If this happens, either turn off
the television receiver or use the normal-speed dubbing
mode.
and press the
direction.
(direction) button to select the travel
3 Insert the blank tape with side A facing out into deck B, and
press the
recorded.
(direction) button to select the side to be
4 Select the REVERSE MODE.
5 Press to ‘‘00 00’’. (Deck B)
6 Press the SYNCHRO DUBBING (NORM or HIGH SPEED)
button to start dubbing.
7 Press the (stop) button of deck B to stop dubbing.
When deck B stops, the dubbing mode is automatically
released.
•
Synchro record muting
When deck A stops or enters any mode other than the play-
back mode during dubbing, deck B enters the record mute
operation automatically and then enters the record-pause
mode.
– 12 –
MAINTENANCE
The importance of cleaning
Demagnetizing the heads
When the tape is moving, magnetic powder and dust naturally
accumulate on the heads, capstan and pinch roller. When they
become too dirty.
Magnetic objects brought close to the head or using the deck for
a long period of time, results in magnetization of the head, thus
noise occurs. When the noise is excessive, high frequencies on
the recorded tape may be erased.
Demagnetize the heads and other metal parts that come into
contact with the tape every 20–30 hours of use with a head
demagnetizer (available from your audio store).
•
tone quality deteriorates.
•
the output sound level drops.
•
the previous sound is not erased satisfactorily.
recordings are not satisfactory.
•
Because of this, clean the heads, etc. every 10 hours of use so
that optimum recordings will be made.
Example: Deck B
Cleaning the heads, pinch roller and capstan
Head
demagnetizer
Wipe the heads, the capstan, etc. with a cotton swab with its tip
dipped in alcohol. For effective cleaning, use a cleaning kit avail-
able from your audio store. After cleaning, be sure that the
cleaning fluid has completely dried before loading a cassette.
Deck B
Capstan
Pinch roller
Deck A
Deck B
head
– 13 –
TROUBLESHOOTING
What appears to be trouble is not always real trouble. Make
sure first....
1. Cassette cannot be loaded.
5. Recording cannot be performed.
•
•
•
Are the safety tabs of cassette tape broken?
Are all connections properly and securely made?
Is the head section dirty?
•
Is the cassette positioned correctly?
2. When PLAY button is pressed, tape does not move.
6. Previous recording is not completely erased.
•
•
Is the tape too loosely wound?
Is the erase head dirty?
3. Tape runs, but no sound is heard.
7. Since tape speed is irregular, wow and flutter occur.
•
•
Are all connections properly and securely made?
Is the pinch roller or capstan dirty?
•
•
Is the MONITOR switch of the stereo amplifier set to the
Is the tape rewound too tight?
TAPE position?
Is the VOLUME control of the stereo amplifier set to MIN?
4. Sound quality is poor.
•
•
Is the DOLBY NR button set to the right setting?
Is the head section dirty?
Is the record/playback head magnetized?
Is the tape worn out?
•
•
•
– 14 –
SPECIFICATIONS
Type
Track system
Tape speed
: Double cassette deck
: 4-track, 2-channel
Motors
: Electric governed DC motor for capstan
x 1
DC motor for reel x 1
DC motor for mechanism drive x 1
(For both decks A and B)
: 4.8 cm/sec (1-7/8 inch/sec) (Normal)
9.5 cm/sec (3-3/4 inch/sec) (High)
: (–20 dB recording)
Type IV tape ; 20–17,000 Hz
30–16,000 Hz (±3dB)
Frequency
response
Fast forward/rewind : Approx. 110 sec. with C-60 cassette
time
Type II tape ; 20–16,000 Hz
30–15,000 Hz (±3dB)
Input terminals
LINE IN
: Input sensitivity; 80 mV (0 VU)
Input impedance; 50 kΩ
: Input sensitivity; 0.4m V (–68dBV)
(0 VU)
Type I tape ; 20–16,000 Hz
30–15,000 Hz (±3dB)
(x 1 circuit)
MIC x 1
(Monaural)
S/N ratio
: 58 dB (S = 315 Hz, k3 = 3%,
N = A-weighted, Type IV tape)
The S/N is improved by about 15 dB at
500 Hz and by max. 20 dB at 1 kHz z
10 kHz with Dolby C NR on and
improved by 5 dB at 1 kHz and by
10 dB at above 5 kHz with Dolby B NR
on.
Matching impedance; 600 Ω z 10 kΩ
Output terminals
LINE OUT
: Output level; 300 mV (0 VU)
Output impedance; 5 kΩ
: Output level; 0.3 mW/8 Ω (0 VU)
Matching impedance 8 Ω–1 kΩ
: COMPU LINK-3/SYNCHRO x 2
(x 1 circuit)
PHONES x 1
Other terminals
Power
Improvement of
MOL
Wow and flutter
Channel
: 4 dB at 10 kHz with Dolby C NR on.
requirement
: AC 230 V, 50 Hz (B version)
AC 120 V, 60 Hz (J version)
: 0.08% (WRMS), ±0.2% (DIN/IEC)
: 40 dB (1 kHz)
Power
separation
Crosstalk
Harmonic
distortion
consumption
: With power on 17 W
With power standby 4.0 W
: 435 x 139 x 331 mm
(17-3/16’’ x 5-1/2’’ x 13-1/16’’)
: 5.1 kg (11.3 lbs.) (B version)
5.0 kg (11.1 lbs.) (J version)
: Pin plug cord ....................................... 2
Remote cable ...................................... 1
: 60 dB (1 kHz)
: k3; 0.8% (Type IV tape, 315 Hz, 0 VU)
Dimensions
(W x H x D)
Mass
Heads
: Deck A; METAPERM head for playback
x 1
Deck B; METAPERM head for
recording/playback, 2-gap fer-
rite head for erasure; combina-
tion head x 1
Accessories
Design and specifications are subject to change without notice.
– 15 –
VICTOR COMPANY OF JAPAN, LIMITED
Printed in Malaysia
VNN2356-671M
© 1997 VICTOR COMPANY OF JAPAN, LIMITED
|