COLOUR VIDEO MONITOR
INSTRUCTIONS
TM-2100PN-K
B
A
–
+
Y/ C
VIDEO
VIDEO
ON
OFF
INPUT SELECT
PHASE CHROMA BRIGHT CONTRAST
MENU
VOLUME/SELECT
POWER
TM-2100PN-K
LCT0054-002A-H
LCT0054-002A-H
1
02.07.25, 3:44 PM
POWER CONNECTION
WARNING
The wire which is coloured green-and-yellow must be connected
to the terminal which is marked with the letter E or the safety
earth symbol ˙ or coloured green or green-and-yellow.
Do not cut off the main plug from this equipment.
If the plug fitted is not suitable for the power points in your
home or the cable is too short to reach a power point, then
obtain an appropriate safety approved extension lead or
adapter or consult your dealer.
The wire which is coloured blue must be connected to the
terminal which is marked with the letter N or coloured black.
If nonetheless the mains plug is cut off, remove the fuse and
dispose of the plug immediately, to avoid a possible shock
hazard by inadvertent connection to the main supply.
The wire which is coloured brown must be connected to the
terminal which is marked with the letter L or coloured red.
When replacing the fuse, be sure to use only a correctly rated
approved type, re-fit the fuse cover.
If a new main plug has to be fitted, then follow the instruction
given below:
IF IN DOUBT —— CONSULT A COMPETENT ELECTRI-
CIAN.
WARNING:
THIS APPARATUS MUST BE EARTHED.
How To Replace The Fuse
IMPORTANT.
The wires in the mains lead on this product are coloured in
accordance with the following cord:
Green-and-yellow : Earth
Open the fuse compartment with the blade screwdriver, and
replace the fuse.
Blue
Brown
: Neutral
: Live
As these colours may not correspond with the coloured
making identifying the terminals in your plug, proceed as
follows:
Fuse
CONTENTS
SAFETY PRECAUTIONS .......................................................................................... 2
CONTROLS AND FEATURES................................................................................... 4
HOW TO HANDLE BASIC OPERATIONS ................................................................ 6
HOW TO USE THE MENU FUNCTIONS................................................................... 7
HOW TO INITIALISE THE SETTING....................................................................... 10
BASIC CONNECTION EXAMPLE ............................................................................11
TROUBLESHOOTING ............................................................................................. 13
SPECIFICATIONS.................................................................................................... 14
3
LCT0054-002A-H
3
02.07.25, 3:44 PM
CONTROLS AND FEATURES
FRONT VIEW
<Front Panel>
1
3
5
7
9
11
2
4
6
8
10
15
B
A
–
+
Y/ C
VIDEO
VIDEO
ON
OFF
INPUT SELECT
PHASE CHROMA BRIGHT CONTRAST
MENU
VOLUME/SELECT
POWER
TM-2100PN-K
B
A
O
–
+
Y/
C
V
I
D
E
O
V
I
D
E
ON
OFF
INPUT SELECT
PHASE CHROMA BRIGHT CONTRAST
MENU
VOLUME/SELECT
POWER
TM-2100PN-K
12 13 14
9 Input A (VIDEO) button [INPUT SELECT A
1 Phase button [PHASE
]
VIDEO ]
Press this button to set the picture hue adjustment mode.
Adjust the value with the VOLUME/SELECT buttons. Also
used as a control button in the menu function mode.
Selects the video signal input to the VIDEO A terminal
(BNC connector) and the audio signal input to the AUDIO
A terminal (RCA connector) on the rear panel. When
selected, the input A (VIDEO) indicator $ lights.
2 Chroma button [CHROMA
]
Press this button to set the picture colour density adjust-
ment mode. Adjust the value with the VOLUME/SELECT
buttons. Also used as a control button in the menu
function mode.
10 Power indicator
Lights in green when the power is ON.
Lit : When the power is on.
Unlit : When the power is off.
3 Brightness button [BRIGHT
]
11 Power switch [POWER
]
Press this button to adjust picture brightness. Adjust the
value with the VOLUME/SELECT buttons. Also used as a
control button in the menu function mode.
Press this switch to turn the power on or off.
_ ON : Power is turned on.
— OFF : Power is turned off.
4 Contrast button [CONTRAST
]
12 Input B (Y/C) indicator
Press this button to adjust picture contrast. Adjust the
value with the VOLUME/SELECT buttons. Also used as a
control button in the menu function mode.
Lights in green when the Input B (Y/C) is selected.
13 Input B (VIDEO) indicator
Lights in green when the Input B (VIDEO) is selected.
5 Menu button [MENU]
14 Input A (VIDEO) indicator
Displays and exits the <MENU> screen.
Pressing the PHASE button with the Menu button
depressed will display the <SET-UP MENU> screen.
Lights in green when the Input A (VIDEO) is selected.
15 Speaker
6 Volume/Select buttons [VOLUME/
A built-in speaker is located inside the right side panel
when the monitor is viewed from the front.
SELECT –
+]
Adjusts the speaker volume. Also used as a control button
in the menu function mode.
7 Input B (Y/C) button [INPUT SELECT B Y/C ]
Selects the video signal input to the VIDEO B (Y/C)
terminal (mini DIN 4 pin connector) and the audio signal
input to the AUDIO B terminal (RCA connector) on the
rear panel. When selected, the input B (Y/C) indicator @
lights.
8 Input B (VIDEO) button [INPUT SELECT B
VIDEO ]
Selects the video signal input to the VIDEO B terminal
(BNC connector) and the audio signal input to the AUDIO
B terminal (RCA connector) on the rear panel. When
selected, the input B (VIDEO) indicator # lights.
4
LCT0054-002A-H
4
02.07.25, 3:44 PM
REAR VIEW
<Rear Panel>
IN
OUT
OUT
A
16
17
IN
VIDEO
B
IN
IN
IN
O
U
T
A
B
OU
T
Y/ C
VIDEO
18
IN
O
Y/
C
UT
OUT
A
B
IN
IN
IN
O
U
T
A
UDIO
OU
T
OU
T
REMOTE
IN
OUT
A
19
20
21
To AC outlet
(230 V AC, 50 Hz/60 Hz)
AUDIO
IN
OUT
OUT
B
22
IN
REMOTE
23
Notes:
16 Video A terminals [VIDEO A IN/OUT]
Video signal input (IN) and output (OUT) terminals.
The output terminal is bridge-connected.
* For corresponding video signals, use the VIDEO A
terminal ^.
IN : Video signal input terminal
OUT : Bridge-connected video signal output terminal
* Also refer to the BASIC CONNECTION EXAMPLE on
pages 11 and 12.
Notes:
20 Audio B terminals [AUDIO B IN/OUT]
Input (IN) and output (OUT) terminals for the audio signals
corresponding to the VIDEO B terminals & or VIDEO B (Y/
C) terminals *. The output terminal is bridge-connected.
* For corresponding audio signals, use the AUDIO A
terminals (.
* Also refer to the BASIC CONNECTION EXAMPLE on
pages 11 and 12.
IN
: Audio signal input terminal
OUT : Bridge-connected audio signal output terminal
17 Video B terminals [VIDEO B IN/OUT]
Video signal input (IN) and output (OUT) terminals.
The output terminal is bridge-connected.
Notes:
* For corresponding video signals, use the VIDEO B
terminals & or VIDEO B (Y/C) terminals *.
* Also refer to the BASIC CONNECTION EXAMPLE on
pages 11 and 12.
IN : Video signal input terminal
OUT : Bridge-connected video signal output terminal
Notes:
21 Remote terminals [REMOTE IN/OUT]
Input (IN) and output (OUT) terminals for external control.
The output terminal is bridge-connected. External control
is available either to select the ASPECT RATIO or to
select ON or OFF in BRIGHTNESS P.S. function mode.
Set the external control in the <SET-UP MENU> screen
mode.
* For corresponding audio signals, use the AUDIO B
terminals ).
* Also refer to the BASIC CONNECTION EXAMPLE on
pages 11 and 12.
18 Video B (Y/C) terminals [VIDEO B Y/C IN/
OUT]
Y/C (S-Video) signal input (IN) and output (OUT) termi-
nals.
External control switch
External control
functions
Open circuit
(open)
Short circuit
(short)
The output terminal is bridge-connected.
IN : Y/C-separated (S-video) signal input terminal
OUT : Bridge-connected Y/C-separated (S-video) signal
output terminal
ASPECT RATIO
4–3 (4:3)
16–9 (16:9)
BRIGHTNESS P.S.
OFF
ON
Notes:
Note:
* For corresponding audio signals, use the AUDIO B
terminals ).
* Also refer to the BASIC CONNECTION EXAMPLE on
pages 11 and 12.
* Also refer to the BASIC CONNECTION EXAMPLE on
pages 11 and 12.
22 AC Inlet [AC IN]
Power input connector. Connect the provided AC power
cord q to an AC outlet (230 V AC, 50 Hz/60 Hz).
19 Audio A terminal [AUDIO A IN/OUT]
Input (IN) and output (OUT) terminals for the audio signal
corresponding the VIDEO A terminals ^. The output
terminal is bridge-connected.
23 Power cord
Connects the provided power cord (230 V AC, 50 Hz/
60 Hz) to the AC IN connector.
IN : Audio signal input terminal
OUT : Bridge-connected audio signal output terminal
5
LCT0054-002A-H
5
02.07.25, 3:44 PM
HOW TO HANDLE BASIC
OPERATIONS
BASIC OPERATION
1. Press the POWER switch to turn on the power.
Colour system indication
(PAL or NTSC)
PAL
_ON : Power turns ON. (Power indicator: lit)
—OFF : Power turns OFF. (Power indicator: unlit)
ON
OFF
POWER
2. Press the INPUT SELECT button to choose input.
Selects video/audio signals input to terminals on the rear
panel.
B
A
Y/ C
VIDEO
VIDEO
INPUT
SELECT
button
Terminals on the rear panel
With regard to Colour system indication
INPUT SELECT
● With the COLOR SYSTEM setting set
to AUTO mode, when you turn on the
power or select inputs, the colour
system indication appears for about 3
seconds on the screen while PAL or
NTSC signals are being detected.
It does not appear when receiving B/
W signal or when no signal is input.
See page 7 for COLOR SYSTEM
Video signal input
Audio signal input
1 Input A
VIDEO A terminal
AUDIO A terminal
(VIDEO)
2 Input B
VIDEO B terminal
VIDEO B (Y/C) terminal
(VIDEO)
AUDIO B terminal
3 Input B
(Y/C)
setting.
00 ~ 50
3. Press the VOLUME/SELECT buttons to adjust the
speaker volume.
–
+
Press this button to display the speaker volume level on the
screen.
+ : The Built-in speaker volume is increased. (00 = 50)
– : The Built-in speaker volume is decreased. (50 = 00)
* Screen indication will disappear about 10 seconds after
operating.
VOLUME/SELECT
VOLUME
:
20
+
–
PICTURE ADJUSTMENT
–20 ~ +20
1. Press select button corresponding to the item you
want to adjust.
The item you select is displayed on the screen.
1 PHASE (
2 CHROMA ( ) : Chroma control
3 BRIGHT ( ) : Brightness control
4 CONTRAST ( ) : Contrast control
) : Phase control
PHASE CHROMA BRIGHT CONTRAST
PHASE
:
00
2. Adjust with the VOLUME/SELECT buttons.
VOLUME/SELECT button
–
+
+
–
Items
–
+
Notes:
VOLUME/SELECT
PHASE
(Phase)
reddish
greenish
● Phase control is effective only in the
NTSC colour system mode.
● Chroma control is not effective when
receiving B/W or when no signal is
input.
● When the Chroma control is set to
level “ –20”, the picture turns
monochrome.
CHROMA
(Chroma)
lighter
darker
lower
deeper
brighter
higher
BRIGHT
(Brightness)
CONTRAST
(Contrast)
● “ NO EFFECT” is displayed (For
about 3 seconds) when your selected
function has no effect.
* Screen indication will disappear about 10 seconds
after operating.
6
LCT0054-002A-H
6
02.07.25, 3:44 PM
HOW TO USE THE MENU FUNCTIONS
DISPLAY AND SELECTION IN THE <MENU>
SCREEN MODE (SETTING)
<MENU> screen
You can set the following menu items.
Set them depending on your needs.
1
<MENU >
‰ SHARPNESS
COLOR TEMP.
COLOR SYSTEM
ASPECT RATIO
:
00
• SHARPNESS
• ASPECT RATIO
: 6500
: AUTO
: 4–3
• COLOR TEMP.
• COLOR SYSTEM
• BRIGHTNESS P.S.
BRIGHTNESS P.S. : OFF
1. Press the MENU button.
3
4
2
The <MENU> screen is displayed.
EXIT
MENU
2. Press the PHASE (
to select MENU items.
) or CHROMA (
) button
–
+
A selection mark (3) is put next to the selected item.
PHASE CHROMA BRIGHT CONTRAST
MENU
VOLUME/SELECT
PHASE CHROMA
SHARPNESS
Front panel
button
Function
displayed
Contents
<Front panel button>
1 Selection mark (3): Indicates the
menu item you select.
PHASE (
)
M
Forwards selection mark (3)
Reverses selection mark (3)
COLOR TEMP.
COLOR SYSTEM
ASPECT RATIO
BRIGHTNESS P.S.
2 Menu item: Menu items you can
CHROMA (
)
5
select.
3 Setting display: Indicates the
current settings (value).
4 Function display: The functions of
the front panel buttons (7 buttons on
the left.) correspond to the function
displayed.
3. Press the VOLUME/SELECT buttons to set.
–
+
Front panel
button
Function
displayed
Contents
Function
Contens
displayed
VOLUME/SELECT
+
3
–
Increases (to max. value)
Forwards the setting value
Decreases (to min. value)
Reverses the setting value
VOLUME/
SELECT (+)
M
5
–
Forwards the menu item
Reverses the menu item
VOLUME/
SELECT (–)
Lowers the adjustment
value (to the minimum)
2
+
Raises the adjustment
value (to the maximum)
Menu items
Purpose
Setting range
3
2
Forwards the setting value
Reverses the setting value
Exits the <MENU> screen
SHARPNESS
Picture sharpness
00
+1
+2
9300
+3
+4
+5
Colour temperature of
white balance
EXIT
6500
COLOR TEMP.
Notes:
COLOR
SYSTEM
AUTO
NTSC
16 – 9
ON
AUTO
PAL
Colour system
● BRIGHTNESS P.S. (or B.P.S.) stands for
Brightness Peak Suppressor. This function
is used to suppress (cut) the white peak
portion of the picture, so as to reduce the
picture’s burning on the screen (cathode
ray tube).
● When the BRIGHTNESS P.S. (or B.P.S.)
function is ON, the suppressed white peak
portion (for example, the lit part of a
fluorescent lamp) seems to be blurred.
If required, lower the setting for the B.P.S.
LEVEL in the <SET- UP MENU> screen
mode, or turn off the BRIGHTNESS P.S.
function.
● When the screen aspect ratio is set to 16-9
(16:9) the picture will be vertically reduced.
● If REMOTE is displayed in the ASPECT
RATIO or BRIGHTNESS P.S. setting values
in the <MENU> screen, REMOTE SELECT
is set to “ASPT” or “B.P.S.” in the <SET-UP
MENU> screen. In this case, it is not
possible to adjust the setting ranges for
ASPECT RATIO and BRIGHTNESS P.S.
If you need to make adjustments, use the
external control function or turn off the
REMOTE SELECT setting.
4 – 3
ASPECT RATIO Aspect ratio
BRIGHTNESS
P.S.
Brightness Peak
Suppressor function
OFF
* Normally set the COLOR SYSTEM to the AUTO mode. If reception in the AUTO mode is not good,
set it to the exclusive mode (NTSC or PAL) corresponding to the received colour system.
4. If you want to set the other menu items, repeat
procedures 2 and 3.
5. Press the MENU button to quit.
Front panel
button
Function
displayed
Contents
MENU
Quits (or Releases) the
<MENU> screen
MENU
EXIT
7
LCT0054-002A-H
7
02.07.25, 3:44 PM
HOW TO USE THE MENU
FUNCTIONS (cont’d)
DISPLAY AND SELECTIONS IN THE <SET-UP
MENU> MODE (SETTING)
<SET-UP MENU> screen
You can set the following set-up menu items.
● H. POSITION
● V. POSITION
● WHITE BALANCE
● CONTROL LOCK
● B.P.S. LEVEL
● REMOTE SELECT
1
2
<SET–UP MENU>
‰ H. POSITION
V. POSITION
:
:
00
00
Notes:
WHITE BALANCE
CONTROL LOCK
B. P. S. LEVEL
: OFF
10
● Parameters for H. POSITION and V. POSITION can be set separately depending on
the video input (Input A (VIDEO), Input B (VIDEO) or Input B (Y/C)) selected by the
input select buttons on the front panel.
Select the required video input with the input select buttons on the front panel in
advance.
:
REMOTE SELECT : OFF
3
4
EXIT
● WHITE BALANCE can be set individually at 6500 or 9300 for the colour temperature
value.
Set COLOR TEMP. to the value 6500 or 9300 in the <MENU> screen in advance.
–
+
1. While pressing the MENU button, press the
PHASE CHROMA BRIGHT CONTRAST
MENU
VOLUME/SELECT
PHASE (
) button.
<Front panel button>
The <SET-UP MENU> screen is displayed.
1 Selection mark (3): Indicates the
menu item you select.
PHASE
MENU
2 Menu item: Menu items you can
select.
3 Setting display: Indicates the
current settings (value).
2. Press the PHASE (
) or CHROMA (
) button
4 Function display: The functions of
the front panel buttons (7 buttons on
the left.) correspond to the function
displayed.
to select the desired menu item.
A selection mark (3) is put next to the selected item.
Front panel
Function
PHASE CHROMA
Contents
button
displayed
Function
Contens
displayed
H. POSITION
V. POSITION
PHASE (
CHROMA (
)
M
Forwards selection mark (3)
Reverses selection mark (3)
M
5
–
Forwards the menu item
Reverses the menu item
)
5
WHITE BALANCE
CONTROL LOCK
B.P.S. LEVEL
Lowers the adjustment
value (to the minimum)
+
Raises the adjustment
value (to the maximum)
REMOTE SELECT
3
2
Forwards the setting value
Reverses the setting value
3. Press the VOLUME/SELECT buttons to set.
Exits the <SET-UP MENU>
screen (release)
EXIT
DRV
Front panel
button
Function
displayed
–
+
Contents
Selects DRV adjustment
+
3
Increases (to max. value)
Forwards the setting value
VOLUME/SELECT
Selects CUT OFF
adjustment
CUTO
VOLUME/
SELECT (+)
R
G
B
Adjusts red signal level
Adjusts green signal level
Adjusts blue signal level
CUTO
Selects CUT OFF setting
screen
–
2
Decreases (to min. value)
Reverses the setting value
Selects DRIVE setting screen
VOLUME/
SELECT (–)
Turns the ON-SCREEN
display on or off. (This
function is effective only in
the DRIVE or CUT OFF
adjustment mode.)
DRV
DISP
Note:
● For the WHITE BALANCE setting, select the CUT OFF or
DRIVE setting screen, then select the buttons (PHASE/
CHROMA/BRIGHT) corresponding to the function indicated
(R/G/B).
8
LCT0054-002A-H
8
02.07.25, 3:45 PM
Set-up menu items
Purpose
Settings
H. POSITION
Adjusts the horizontal position of
the screen (+ : Horizontal position
shifts to the right/–: Horizontal
position shifts to the left)
–09 –08 •••••• –01 00 +01 •••••• +08 +09
V. POSITION
Adjusts the vertical position on the
screen (+: Vertical position moves
down/–: Vertical position moves up)
–09 –08 •••••• –01 00 +01 •••••• +08 +09
WHITE BALANCE
Adjusts the white balance
Selects DRIVE (DRV) or CUT OFF (CUTO) adjustment.
Screen setting is changed to the selected setting mode.
Select R/G/B buttons corresponding to the function display
to adjust.
DRIVE
R.DRIVE
G.DRIVE
B.DRIVE
Adjusts red level
–09 –08 •••••• –01 00 +01 •••••• +08 +09
–09 –08 •••••• –01 00 +01 •••••• +08 +09
–09 –08 •••••• –01 00 +01 •••••• +08 +09
Adjusts green level
Adjusts blue level
Adjusts red cut off
Adjusts green cut off
Adjusts blue cut off
CUT OFF R. CUT OFF
G. CUT OFF
–09 –08 •••••• –01 00 +01 •••••• +08 +09
–09 –08 •••••• –01 00 +01 •••••• +08 +09
–09 –08 •••••• –01 00 +01 •••••• +08 +09
B. CUT OFF
CONTROL LOCK
Sets the operation buttons on the
front panel to control lock mode
OFF
ON
B. P. S. LEVEL
Sets the level for Brightness Peak
Suppressor function
00
01 ••••••• 09 10 11 ••••••• 19 20
REMOTE SELECT
Sets the external control function
(ASPECT RATIO or BRIGHTNESS
P.S.)
OFF
ASPT
OFF
B.P.S.
* ASPT : ASPECT RATIO
B.P.S.: BRIGHTNESS P.S.
Notes:
4. To set the other set-up menu items, repeat the
procedures 2 and 3.
● When the CONTROL LOCK function
is set to ON, pressing operation
buttons on the front panel will display
the message “CONTROL LOCK ON!”
on the screen for about 3 seconds.
● The CONTROL LOCK function is
maintained even when the power is
turned off.
● To turn off the CONTROL LOCK
function, while holding the MENU
button press the PHASE button. Then
set the CONTROL LOCK function to
OFF.
5. Press the MENU button to quit.
Front panel
button
Function
displayed
Contents
MENU
Quits (or Releases) the
<MENU> screen
MENU
EXIT
● Even when the CONTROL LOCK
function is set to ON, the following
operations are available:
– Power Switch operation.
– Sound volume adjustment with the
VOLUME/SELECT button.
– Display or exit of the <SET-UP
MENU> screen.
– External control of ASPECT RATIO
or BRIGHTNESS P.S. when
REMOTE SELECT is set to ON .
9
LCT0054-002A-H
9
02.07.25, 3:45 PM
HOW TO INITIALISE THE
SETTING
SCREEN DISPLAY AND SELECTIONS IN THE
<SET-UP MENU> RESET MODE
You can set <MENU> and <SET-UP MENU> screen items, picture adjustment items and
the volume level to their factory-set (initial) values.
<SET-UP MENU> RESET screen
<SET–UP MENU> RESET
Are you sure ?
“Yes” then <CONTRAST>
1. Press the Power ( ) Switch to turn the power
“No”
then <+> or <–>
OFF (—).
ON
OFF
POWER
2. While pressing both MENU button and PHASE (
)
Initial settings
button, press the Power ( ) switch to turn the power
Initialisation
(setting)
Functions (Items)
ON (_).
SHARPNESS
00
The <SET-UP MENU> RESET screen is displayed.
COLOR TEMP.
COLOR SYSTEM
ASPECT RATIO
6500
AUTO
4–3
ON
OFF
Note:
POWER
PHASE
MENU
BRIGHTNESS P.S. OFF
● The <SET-UP MENU> PRESET screen will not be
displayed if the MENU or PHASE buttons are pressed
for a very short time. Keep pressing them until the
display screen appears.
H. POSITION
V. POSITION
WHITE BALANCE
00
00
R. CUT OFF 00
G. CUT OFF 00
B. CUT OFF 00
3. Setting
R. DRIVE
G. DRIVE
B. DRIVE
00
00
00
ꢀ Initialisation is required.
Press the CONTRAST ( ) button.
* Initialisation is completed, and the <SET-UP MENU>
RESET screen disappears.
CONTROL LOCK OFF
B.P.S. LEVEL 10
REMOTE SELECT OFF
CONTRAST
ꢀ Initialisation is not required.
PHASE
00
00
00
00
CHROMA
CONTRAST
BRIGHT
Press the VOLUME/SELECT [+] or [–] button.
* Initialisation is aborted, and the <SET-UP MENU>
RESET screen disappears.
–
+
VOLUME/SELECT
VOLUME
20
10
LCT0054-002A-H
10
02.07.25, 3:45 PM
BASIC CONNECTION EXAMPLE
Notes:
* Before connecting your system, make sure that all units are turned off.
* The illustration below shows some examples of different connections. Terminal connections may differ depending on the
component connected. Be sure to refer to the instructions provided with the unit(s) you are connecting.
* Each pair of input (IN) and output (OUT) terminals are bridge-connected.
* If you’re not connecting any equipment to a bridged output (OUT) terminal, be sure not to connect any other cables to the
bridged output (OUT) terminal as this will cause the terminating resistance switch to open (auto terminate function).
* When making a bridge connection, connect the input (IN) and output (OUT) terminals on the monitor to separate video
components.
(For example, if both terminals are connected to the same VCR, resonance may occur except during playback. This is caused by
the same video signal “looping” between the VCRs, and is not a malfunction.)
* Select the video input (Input A (VIDEO), Input B (Y/C) or Input B (VIDEO)) with the INPUT SELECT button on the front panel.
* The ASPECT RATIO or BRIGHTNESS P.S. function can be controlled via the REMOTE terminal. To do this, set REMOTE
SELECT in the <SET-UP MENU> mode. (Refer to pages 8 and 9.)
7 VIDEO A Connection Example
(Select Input A (VIDEO) button)
Video
(Video signal cable)
IN
IN
OUT
OUT
Video
A
B
(Video signal cable)
Video Camera
VIDEO
IN
VCR
Y/ C
OUT
Video Monitor
Audio
Audio
(Audio signal cable)
IN
IN
IN
OUT
A
B
(Audio signal cable)
AUDIO
OUT
OUT
Video Monitor
VCR
REMOTE
External control switch
REMOTE
open circuit (open)
REMOTE
(Remote cable)
(Remote cable)
RCA pin
short circuit (short)
B
A
O
–
+
Y
/
C
V
I
D
E
O
V
I
D
E
_
O
N
—
O
F
F
I
N
P
U
TS
E
L
E
C
T
TM-2100PN
P
H
A
S
E
C
H
R
O
M
A
B
R
I
G
H
T
C
O
N
T
R
A
S
T
M
E
N
U
V
O
L
U
M
E
/
S
E
L
E
C
T
P
O
W
E
R
External control switch
TM-2100PN-K
<second one>
External control
functions
Open circuit Short circuit
(open)
4–3 (4:3)
OFF
(short)
16–9 (16:9)
ON
: Signal Flow
ASPECT RATIO
BRIGHTNESS P.S.
11
LCT0054-002A-H
11
02.07.25, 3:45 PM
BASIC CONNECTION EXAMPLE
(cont’d)
7 VIDEO B (VIDEO) Connection Example
(Select Input B (VIDEO) button)
IN
IN
OUT
A
B
Video Camera
Video
Video
(Video signal cable)
OUT (Video signal cable)
VIDEO
IN
VCR
Y/ C
OUT
Video Monitor
IN
IN
IN
OUT
A
B
AUDIO
Audio
OUT
OUT
Audio
(Audio signal cable)
(Audio signal cable)
Video Monitor
VCR
REMOTE
External control switch
REMOTE
open circuit (open)
REMOTE
(Remote cable)
RCA pin
(Remote cable)
short circuit (short)
B
A
O
–
+
Y
/
C
V
I
D
E
O
V
I
D
E
_
O
N
—
O
F
F
I
N
P
U
TS
E
L
E
C
T
TM-2100PN
P
H
A
S
E
C
H
R
O
M
A
B
R
I
G
H
T
C
O
N
T
R
A
S
T
M
E
N
U
V
O
L
U
M
E
/
S
E
L
E
C
T
P
O
W
E
R
External control switch
TM-2100PN-K
<second one>
External control
functions
Open circuit Short circuit
(open)
4–3 (4:3)
OFF
(short)
16–9 (16:9)
ON
: Signal Flow
ASPECT RATIO
BRIGHTNESS P.S.
7 VIDEO B (Y/C) Connection Example
(Select Input B (Y/C) button)
IN
IN
OUT
OUT
A
Video Camera
VIDEO
B
Y/C (S-video)
IN
VCR
(Y/C (S-video) signal cable)
Y/ C
OUT
Y/C (S-video)
Video Monitor
(Y/C (S-video) signal cable)
IN
IN
IN
OUT
A
AUDIO
B
Audio
OUT
OUT
Audio
(Audio signal cable)
(Audio signal cable)
Video Monitor
VCR
REMOTE
External control switch
REMOTE
open circuit (open)
REMOTE
RCA pin
(Remote cable)
(Remote cable)
short circuit (short)
B
A
O
–
+
Y
/
C
V
I
D
E
O
V
I
D
E
_
O
N
—
O
F
F
I
N
P
U
TS
E
L
E
C
T
TM-2100PN
P
H
A
S
E
C
H
R
O
M
A
B
R
I
G
H
T
C
O
N
T
R
A
S
T
M
E
N
U
V
O
L
U
M
E
/
S
E
L
E
C
T
P
O
W
E
R
External control switch
TM-2100PN-K
<second one>
External control
functions
Open circuit Short circuit
(open)
4–3 (4:3)
OFF
(short)
16–9 (16:9)
ON
: Signal Flow
ASPECT RATIO
BRIGHTNESS P.S.
12
LCT0054-002A-H
12
02.07.25, 3:45 PM
TROUBLESHOOTING
Solutions to common problems related to your monitor are described here. If none of the solutions presented here
solves the problem, unplug the monitor and consult a JVC-authorised dealer or service centre for assistance.
Problems
Points to be checked
Measures (Remedy)
Firmly insert the power plug.
No power supply.
Is the power plug loosened or disconnected?
No picture with the
power on.
Is the video signal output from the connected
component?
Set the connected component correctly.
Is the input signal selected properly?
Select the required video signal input with the
Input select button. (See page 6.)
Is the video cable disconnected?
Connect the video signal cable firmly.
(See pages 11 and 12.)
No sound.
Is the audio signal output from the connected
component?
Set the connected component correctly.
Is the volume output set to minimum?
Adjust the speaker volume with the VOLUME/
SELECT buttons. (See page 6.)
Is the audio cable disconnected?
Connect the audio signal cable firmly.
(See pages 11 and 12.)
Shaking picture.
Is the monitor close to a device generating a
strong magnetic field?
Move the device away from the monitor until the
picture stabilises.
No colours, wrong
colour, or dark picture.
Is the colour system selected properly?
Set the COLOR SYSTEM in the <MENU> screen
mode to [AUTO] mode. (See page 7.)
Has the picture control setting (CONTRAST,
BRIGHT, CHROMA or PHASE) been changed?
Set each picture control to the standard setting.
(See page 6.)
Unnatural, irregularly
coloured, or distorted
picture.
Is the monitor close to a speaker, magnet or any Move the device away from the monitor and turn
other device generating a strong magnetic field? the monitor’s power off. Wait at least 30 minutes,
then turn the power on again.
Dark stripes appear
at the top and bottom
of the screen, picture
vertically squeezed.
Is the aspect ratio set to 16:9?
Set the ASPECT RATIO in the <MENU> screen
mode to [4 : 3 (4 - 3)] (See page 7.)
When controlling externally, ASPECT RATIO
should be set to [4 : 3 (4-3)].
(See pages 11 and 12.)
White peak portion of
the picture (for
example, the lit part
of a fluorescent lamp)
is dark, unclear, and
the colour is blurred.
Is the BRIGHTNESS P.S. function set to ON?
Set the BRIGHTNESS P.S. function in the
<MENU> screen mode to OFF. (See page 7.)
When controlling externally, BRIGHTNESS P.S.
function should be set to OFF.
(See pages 11 and 12.)
Front panel button
does not function.
Are the operation buttons on the front panel
locked? ( Has CONTROL LOCK function set to
ON?)
Set the CONTROL LOCK to OFF in the <SET-
UP MENU> screen mode. (See pages 8 and 9.)
The following are not malfunctions:
● When a bright still image (such as a white cloth) is displayed for a long period, it may appear to be coloured. This is due to the
structure of the cathode ray tube and will be deleted when another image is displayed.
● You experience a mild electric shock when you touch the picture tube. This phenomenon is due to a normal buildup of static
electricity on the CRT and is not harmful.
● The monitor emits a strange sound when the room temperature changes suddenly. This is only a problem if an abnormality
appears on the screen as well.
13
LCT0054-002A-H
13
02.07.25, 3:45 PM
SPECIFICATIONS
MODEL
TM-2100PN-K
Colour video monitor
PAL, NTSC (3.58)
Type
Colour system
Picture tube
54 cm measured diagonally,
flat-square type,
90° deflection, in-line gun,
vertical line trio type
(phosphor stripe pitch 0.69 mm)
Effective screen size
Width
Height
Diagonal
406.4 mm
304.8 mm
508 mm
Scanning frequency
Horizontal resolution
H : 15.734 kHz (NTSC), 15.625 kHz (PAL)
V : 59.94 Hz (NTSC), 50 Hz (PAL)
450 TV lines or more
(Y/C input mode)
Input terminals
VIDEO A
Composite video: 1 line, BNC connector x 2,
1 V(p-p), 75 Ω negative sync
(bridge connection possible, auto termination)
VIDEO B
Composite video: 1 line, BNC connector x 2,
1 V(p-p), 75 Ω negative sync
(bridge connection possible, auto termination)
Y/C-separated: 1 line, mini-DIN 4-pin connector x 2
Y: 1.0 V(p-p), 75 Ω
C: 0.286 V(p-p), 75 Ω (NTSC), 0.3 V(p-p), 75 Ω (PAL)
(bridge connection possible, auto termination)
AUDIO A
AUDIO B
REMOTE
1 line (monaural), RCA pin x 2, 0.5 V(rms), high-impedance
(bridge connection possible)
1 line (monaural), RCA pin x 2, 0.5 V(rms), high-impedance
(bridge connection possible)
1 line, RCA pin x 2 (bridge connection possible)
1 W (monaural)
Audio power output
Built-in speaker
8 cm round x 1, impedance of 8 Ω
Environmental conditions
Operation temperature: 0 – 40 °C
Operation humidity: 20 – 80% (non-condensing)
Power requirements
Power consumption
Dimensions
230 V AC, 50 Hz/ 60 Hz
0.72A (230 V AC)
Width
Height
Depth
476 mm
407.5 mm
492 mm
Weight
28.5 kg
AC power cord (2 m) x 1
Accessory
* Illustrations used in this manual are for explanatory purposes only. The appearance of the actual product may differ slightly.
* Dimensions and weight are approximate.
* E. & O. E. Design and specifications subject to change without notice.
14
LCT0054-002A-H
14
02.07.25, 3:45 PM
7 Dimensions
Unit : mm
< Side View >
< Front View >
1.3
479
9.5
476
50.2
*
416.4
B
A
–
+
Y/ C
V
I
D
E
O
V
I
D
E
O
ON
OFF
INPUT SELECT
PHASE CHROMA BRIGHT CONTRAST
MENU
VOLUME/SELECT
POWER
TM-2100PN-K
3.5
105
135
128.5
382.8
492
* Asterisks ( ) are used to indicate front panel
∗
dimensions.
7 Y/C (Mini DIN 4 pin) terminal
specification
2
4
Pin No.
Signal
GND (Y)
GND (C)
Y
IN
1
2
3
4
1
2
3
4
Y/C
OUT
1
3
C
15
LCT0054-002A-H
15
02.07.25, 3:45 PM
VICTOR COMPANY OF JAPAN, LIMITED
Printed in Thailand
0702-Y-U-JMT
2002 VICTOR COMPANY OF JAPAN, LIMITED
©
LCT0054-002A-H
16
02.07.25, 3:45 PM
|