SAFETY PRECAUTIONS
FOR USA
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must accept
any interference received, including interference that may
cause undesired operation.
These are general IMPORTANT SAFEGUARDS and
certain items may not apply to all appliances.
BULLET HD IP CAMERA
Instructions (Installation)
IMPORTANT SAFEGUARDS
VN-H157WPU
INFORMATION (FOR CANADA)
1. Read all of these instructions.
2. Save these instructions for later use.
3. All warnings on the product and in the operating instructions
should be adhered to.
4. Unplug this appliance system from the wall outlet before
cleaning. Do not use liquid cleaners or aerosol cleaners. Use a
damp cloth for cleaning.
5. Do not use attachments not recommended by the appliance
manufacturer as they may cause hazards.
RENSEIGNEMENT (POUR CANADA)
This Class A digital apparatus complies with Canadian
ICES-003.
Cet appareil num rique de la Class A est conforme á la
norme NMB-003 du Canada.
6. Do not use this appliance near water - for example, near
a bathtub, washbowl, kitchen sink, or laundry tub, in a wet
basement, or near a swimming pool, etc.
Due to design modifications, data given in this instruction
book are subject to possible change without prior notice.
For Customer Use:
7. Do not place this appliance on an
unstable cart, stand, or table. The
appliance may fall, causing serious
injury to a child or adult, and serious
damage to the appliance. Use only
with a cart or stand recommended
by the manufacturer, or sold with the
appliance. Wall or shelf mounting should
follow the manufacturer’s instructions,
Enter below the Model No. which is located
on the body.
Retain this information for future reference.
FOR EUROPE
WARNING
This is a Class A product. In a domestic environment this
product may cause radio interference in which case the
user may be required to take adequate measures.
Thank you for purchasing this product.
Before operating this unit, please read the instructions carefully
to ensure the best possible performance.
Model No.
Serial No.
Dear Customer
and should use a mounting kit approved
by the manufacturer.
This apparatus is in conformance with the valid European
directives and standards regarding electromagnetic
compatibility and electrical safety.
European representative of JVC KENWOOD Corporation is:
JVC Technical Services Europe GmbH
Postfach 10 05 04
An appliance and cart combination should be moved with care.
Quick stops, excessive force, and uneven surfaces may cause
the appliance and cart combination to overturn.
8. Slots and openings in the cabinet and the back or bottom are
provided for ventilation, and to insure reliable operation of the
appliance and to protect it from overheating, these openings
must not be blocked or covered. The openings should never
be blocked by placing the appliance on a bed, sofa, rug, or
other similar surface. This appliance should never be placed
near or over a radiator or heat register. This appliance should
not be placed in a built-in installation such as a bookcase
unless proper ventilation is provided.
9. This appliance should be operated only from the type of power
source indicated on the marking label. If you are not sure of
the type of power supplied to your home, consult your dealer
or local power company. For appliance designed to operate
from battery power, refer to the operating instructions.
10. For added protection for this product during a lightning storm,
or when it is left unattended and unused for long periods of
time, unplug it from the wall outlet and disconnect the antenna
or cable system. This will prevent damage to the product due
to lightning and power-line surges.
11. Do not allow anything to rest on the power cord. Do not locate
this appliance where the cord will be abused by persons
walking on it.
12. Follow all warnings and instructions marked on the appliance.
13. Do not overload wall outlets and extension cords as this can
result in fire or electric shock.
14. Never push objects of any kind into this appliance through
cabinet slots as they may touch dangerous voltage points
or short out parts that could result in a fire or electric shock.
Never spill liquid of any kind on the appliance.
15. Do not attempt to service this appliance yourself as opening
or removing covers may expose you to dangerous voltage
or other hazards. Refer all servicing to qualified service
personnel.
16. Unplug this appliance from the wall outlet and refer servicing to
qualified service personnel under the following conditions:
a. When the power cord or plug is damaged or frayed.
b. If liquid has been spilled into the appliance.
The standard camera installation procedure can be found on the back side of this page.
© 2012 JVC KENWOOD Corporation
LST1238-001B
61145 Friedberg
Germany
Safety precautions
Sehr geehrter Kunde, sehr geehrte Kundin, dieses Gerät
stimmt mit den gültigen europäischen Richtlinien und Normen
bezüglich elektromagnetischer Verträglichkeit und electrischer
Sicherheit überein.
Die europäische Vertretung für die JVC KENWOOD
Corporation ist:
JVC Technical Services Europe GmbH
Postfach 10 05 04
61145 Friedberg
The power rating is AC 24 V, 50/60 Hz or PoE. Use the correct voltage.
Always use the AC 24 V power source that is insulated from the primary power supply.
A level of supplied power that exceeds the ratings may result in failures, smoke or fire. If the camera breaks
down, turn off the power and contact our service center immediately.
If a level of power that exceeds the ratings is supplied, the internal components may be damaged even if no
abnormalities are observed in the appearance and/or operation of the camera. Contact our service center
immediately to arrange for an inspection (charged separately).
Deutschland
Information for Users on Disposal of Old Equipment
Attachments and accessories
[European Union]
This symbol indicates that the electrical and
electronic equipment should not be disposed as
general household waste at its end-of-life.
Instead, the product should be handed over to
the applicable collection point for the recycling
of electrical and electronic equipment for proper
treatment, recovery and recycling in accordance with
your national legislation.
Instructions.......................................................2
CD-ROM...........................................................1
WARRANTY CARD (For USA) ...........................1
SCREW (M4)....................................................2
WRENCH .........................................................1
WASHER..........................................................2
SPRING WASHER...........................................2
MOUNTING BRACKET....................................1
By disposing of this product correctly, you will help
to conserve natural resources and will help prevent
Attention:
potential negative effects on the environment and
This symbol
Operating Precautions
human health which could otherwise be caused by
is only valid in
inappropriate waste handling of this product. For
the European
more information about collection point and recycling
Union.
Storage and Operating Environment
Maintenance
of this product, please contact your local municipal
●
Do not install the camera in the following environments. ● Turn off the power before performing maintenance.
office, your household waste disposal service or the
shop where you purchased the product. Penalties
may be applicable for incorrect disposal of this
waste, in accordance with national legislation.
●
Wipe off dirt on the front cover lens with a lens-cleaning
Doing so may result in malfunctions or failure.
• Hot or cold locations beyond the allowable operating
temperature range (-10 °C to 50 °C).
cloth (or soft cloth). For dirt that cannot be easily
removed, wipe using a neutral detergent diluted with
water. Following that, wipe with a dry cloth. Do not use
thinner or benzene. The surface of the front cover may
dissolve or fog up.
(Business users)
c. If the appliance has been exposed to rain or water.
d. If the appliance does not operate normally by following the
operating instructions. Adjust only those controls that are
covered by the operating instructions as improper adjustment
of other controls may result in damage and will often require
extensive work by a qualified technician to restore the
appliance to normal operation.
e. If the appliance has been dropped or the cabinet has been
damaged.
f. When the appliance exhibits a distinct change in performance
- this indicates a need for service.
•
Locations beyond the allowable operating humidity
range (20 %RH to 90 %RH) (no condensation allowed).
If you wish to dispose of this product, please visit our web
back of the product.
• Near equipment that emits strong magnetic fields,
such as transformers or motors.
• Near equipment that emits radio waves, such as
transceivers and mobile phones.
• Locations in which excessive dust or sand exist.
• Locations that are subject to excessive vibration.
• Locations prone to moisture, such as near windows.
Saving Energy
[Other Countries outside the European Union]
If you wish to dispose of this product, please do so in
accordance with applicable national legislation or other
rules in your country for the treatment of old electrical and
electronic equipment.
● If the camera is not going to be used for a long period
of time, turn off the power or the system for safety
reasons and to conserve energy.
Others
17. When replacement parts are required, be sure the service
technician has used replacement parts specified by the
manufacturer that have the same characteristics as the original
part. Unauthorized substitutions may result in fire, electric
shock or other hazards.
18. Upon completion of any service or repairs to this appliance,
ask the service technician to perform routine safety checks to
determine that the appliance is in safe operating condition.
● This installation should be made by a qualified service
person and should conform to all local codes.
• Special environment where a flammable atmosphere ● This camera has a built-in AGC circuit. Setting AGC
is present.
to "Mid" or "High" increases the sensitivity of a dark
image, and the screen may appear grainy. This is not
a malfunction.
● This installation shall be in accordance with the National
Electrical Code, ANSI/NFPA 70. The unit is to be powered
by a Listed Class 2 power supply or using the PoE.
● The AC 24 V power supply should conform to the following:
Class 2 only (For USA), Isolated power supply only (For
Europe and other).
•
Locations that may contain steam or oil, such as kitchens.
• Locations that are subject to radiation emissions,
X-rays or corrosive gases.
• Locations where chemicals are used, such as
swimming pools.
● Use of this camera and cables connected to this
camera at locations where strong electrical or
● When this camera is used with the white balance set to
"ATW" (Auto Tracking White Balance), the color tone
of some objects may differ slightly from the actual color
due to the principle of the automatic tracking white
balance circuit. This is not a malfunction.
FOR USA AND CANADA
● Any Mention in this manual of Alarm inputs have not been
evaluated by UL to be used for Burglar Alarm Functionality.
magnetic waves are generated (e.g. near a radio, TV,
transformer, monitor, etc.) may result in images being
affected by noise interference or colors being changed.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
● Special technique is required when installing this product.
Please refer to your dealer for installation.
● Rating label is pasted at the bottom or top of the camera
unit.
● For regions with a commercial power frequency of
50 Hz, switch to the Flickerless mode during use
under fluorescent lights (excluding inverter lighting
equipment) to prevent flickers.
● Do not install this camera at locations where cold
air is circulated, such as near the air vent of an air
conditioner. The drastic change in temperature may
fog up the front cover lens.
CAUTION: TO REDUCE THE RISK OF ELECTRICK
SHOCK. DO NOT REMOVE COVER
● JVC is not liable for any compensation if you drop the
camera due to insecure mounting by not following the
installation description. Pay careful attention during
installation.
● When mounting this product to a ceiling or wall, select
a location strong enough to support the weight of this
camera. If the location is not strong enough to support
the weight, be sure to reinforce the ceiling or wall before
installation.
● The camera may drop if the mounting screws are not
tightened securely. Check that the screws are tightened
appropriately and securely.
● Do not install the camera near lighting fixtures of high
temperature, such as spot lights. It might result in failure
or fires.
● It should be noted that it may be unlawful to re-record
pre-recorded tapes, records, or discs without the consent
of the owner of copyright in the sound or video recording,
broadcast or cable program and in any literary, dramatic
musical, or artistic work embodied therein.
● The latest version
Please visit V.NETWORKS web site to check the latest
firmware at
● When the electronic sensitivity enhancement feature
is enabled, the screen may appear grainy and more
white spots may appear because the sensitivity has
increased. However, this is not a malfunction.
(OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
● Do not install this camera at a location that traps heat.
This camera discharges heat from the surface of the
main unit. Do not install it at locations that may trap
heat, such as wall corners.
● This camera is IP66 compliant. However, we do not
guarantee that water has no harmful effects in all
environments.
● If the power supply voltage is momentarily cut off or
reduced due to lightning or the power supply to the
air conditioner being turned on, the image may be
disrupted or noise interference may occur.
The lightning flash wish arrowhead symbol, within
an equilateral triangle is intended to alert the
user to the presence of uninsulated "dangerous
voltage" within the product's enclosure that age"
within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electric
shock to persons.
● This camera may become inoperable if it is brought
from a cold location to a warm location (indoors, etc.)
and condensation forms on the camera. If this occurs,
leave the camera at room temperature for 1 hour, and
then turn on the power.
Handling Precautions
● Do not block the vents.
The exclamation point within an equilateral
triangle is intended to alert the user to
the presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
Inadequate heat ventilation may cause this camera to
malfunction. Be sure not to block the vents around the
camera.
● When using multicast, make use of an IGMPv2-
compliant network switch.
● Some hubs/switches of products that are equipped
with intelligent features may include a broadcast/
multicast suppression function. If this function is
enabled, viewing of multicast images on this camera
may fail.
Copyright Protection
Information for USA
This device complies with part 15 of the FCC Rules. Changes
or modifications not approved by JVC could void the user's
authority to operate the equipment. This equipment has
been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of
this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct
the interference at his own expense.
● With the exception of the user being the copyright
holder or when permission such as for duplication has
been granted by the copyright holder, permission is
required in principle to duplicate, modify or transmit
copyrighted material.
● We recommend the use of a shielded LAN cables for
connection with this camera. The safety and reliability
of this camera has been checked by using shielded
cables.
html
● Unauthorized duplication, modification or transmission
of copyrighted material may constitute a copyright
infringement, and the user may be liable to pay
compensation for damages. When using copyrighted
material, be sure to check the license agreement or
the copyrighted material thoroughly.
● During viewing using the Built-in Viewer, the video
and audio may appear out of sync. This is not a
malfunction.
● Do not point the lens toward a strong light source,
such as the sun. This may result in damage.
● When rights or rights holders are involved with regard
to the targeted subject of duplication, permission may
be required for shooting or using (processing) it. Be
sure to check the licensing conditions thoroughly.
CAUTION
CHANGES OR MODIFICATIONS NOT APPROVED BY JVC
COULD VOID USER’S AUTHORITY TO OPERATE THE
EQUIPMENT.
● Under halogen lamps, light bulbs and other light
sources that emit strong infrared light, black objects
may look almost purple in the recording. It is an
inherent characteristic of this camera and not a defect.
Disclaimer
● The motion detection feature is not a feature to prevent
theft or fire. Our company shall not be liable for any
loss or damage resulting from the use of this feature.
● We shall not be responsible for any loss or damage
caused in the event of privacy invasion as a result of
camera footage created by this product.
● Use of recorded materials without first gaining the prior
consent of the author is forbidden under copyright law
except in cases of personal use.
1
☞ Continued overleaf
2Rotate the lens section at the tip to roughly adjust the focus.
Adjust the field angle and focus
1 Adjust the zoom ratio.
Turn on the power
1Loosen the fastening screw of the zoom adjustment ring, then
move the ring to the right and left to adjust the zoom ratio. After
completing the adjustment, tighten the setscrew.
Lens section
After all connections and installations are completed, turn on the
power of the unit. When the camera is booting, the [STATUS]
indicator lights up orange. It lights up green after booting.
Note
2
• Applying force on the zoom adjustment ring while adjusting the
image size may cause damage.
Moving the zoom adjustment ring beyond its adjustable range
Note
[Status] indicator
Memo
The lighting status of the [STATUS] indicator can be checked via the
opening on the side of the camera.
• Do not hold the lens section when adjusting the direction of the
camera. The lens section may be damaged if you apply force to
it. Also, exercise care not to leave your finger prints on the lens
when you rotate the lens section.
may cause the performance of this camera to deteriorate.
2 Roughly adjust the focus.
•
1Lift the focusing gear control, release the catch from position A
3Return the catch to its original position, and then return the
and insert it into position B to disengage the gear.
focusing adjustment gear to its original position.
Note
3 Connect the camera to a computer, and open the
• If you open the gear beyond position B, the gear shaft is
released from the bearing (C in the figure on the left) to prevent
it from being damaged. In this case, correctly re-insert the shaft
into bearing C and return it to the original position before using it.
Built-in Viewer.
Image Adjustment
• For details about computer settings and methods for connecting
the camera to a computer, refer to “Instructions (IP Address
Settings)”.
Adjust images by watching them on the monitor.
* The diagram depicts the camera directly mounted on the ceiling for
explanation purposes.
The same procedures are performed when mounting the camera on
the wall with the cables pulled out.
4 Select “Day Focus Adjust” from the “Focus” page
in “Advanced Settings”.
• The focus position is automatically adjusted.
• For details on back focus, refer to “Instructions (Setting)” on the
supplied CD-ROM.
Focus adjustment gear
Note
• Before you touch the camera, be sure to touch the metal surface of
the monitor terminal first in order to discharge static electricity.
Otherwise, static electricity may cause the camera to malfunction.
Knob
Note
• It may be difficult to acquire focus the following places.
– Too bright places.
Catches
– Too dark places.
–
Places where brightness always flickering; people are passing by
B
Adjust the shooting direction of the camera
– Places where there is little contrast
– Places where there are repeating
• The focus position can be manually adjusted by using the Built-
in Viewer installed on your computer connected to the camera.
(☞ “Instructions (Setting)”) Resort to this method if it is difficult
to acquire focus automatically.
1
Connect a test monitor to the [MONITOR] terminal.
C
A
2
After checking that the [MONITOR] selection switch
is set to “NTSC”, press the [FOCUS ASSIST] button.
[Focus Assist]
Button
Adjust the sunshade
[MONITOR]
SELECT SW
NTSC
2
75 Ω
termination
Adjust the sunshade.
Zoom adjustment ring
[MONITOR]
terminal
1
PAL
Test monitor
Memo
Stay cover
•
The camera has a 16:9 aspect ratio. If the test monitor has a 4:3 aspect
ratio, the camera image is converted into 4:3 ratio and displayed.
Sunshade
• Set to “NTSC” when connecting to an NTSC monitor, or set to “PAL”
when connecting to a PAL monitor, then hold down the [RESET]
button for approximately three seconds to reboot. While the camera
is rebooting, the [STATUS] indicator lights up orange.
Front cover
1
Sunshade
•
If you keep pressing the [RESET] button for more than 5 s, the camera
enters the Service mode. Do not press this button for more than 5 s.
3 Adjust the shooting direction of the camera.
1Loosen the 2 bolts (M8) which fix the camera to the mounting
bracket with the wrench (provided).
2
Adjust the pan-direction to face the lens toward the subject, holding
the stay cover. The range of adjustment angle is about ± 50°.
3,5
3Fasten the two bolts to fix the camera direction.
4
Pan-direction adjustment
Bolts
(M8, 2-places)
3,5
3
6
3,5
2
Stay cover
Lens
Lens section
Screws for fixing sunshade (3-places)
4-1
1
Turn the front cover clockwise, and attach it to the camera.
Cap
Confirm that the front cover is securely attached.
Bolts
(M6, 2-places)
2 Loosen the screw on the bottom of the camera.
Memo
• Use a long screw driver to avoid damaging the front cover.
[MONITOR]
SELECT SW
NTSC
[Focus Assist] Button
4 Adjust the tilt angle direction of the camera.
4-1 Roughly adjust the tilt angle direction of the camera
3 Loosen the 3 sunshade fixing screws.
Turn the sunshade slightly if it is hard to loosen the screws.
Memo
• If you remove the sunshade fixing screws, the fall prevention wire
comes off. Do not remove the sunshade fixing screws.
[MONITOR]
terminal
1Open the cap (2-places) on the side of the stay cover.
2Loosen the 2 bolts (M6) with the wrench (supplied).
3Take the sunshade, and adjust the tilt angle.
PAL
You can adjust by about 18 degrees for each step.
4If fine adjustment of the tilt angle is necessary, fasten the 2 bolts
(M6) temporarily, and go to step 4-2.
4
Move the sunshade back and forth, and adjust the position.
Memo
5 Adjust the rotation angle of the camera
• Adjust the sunshade when flares or ghosting appear.
• The sunshade may appear in the image of the camera due to the
angle of the lens and the position of the sunshade.
(When the camera is mounted on the wall only)
Adjust the rotation angle of this camera to level the image of the
camera. The range of rotation adjustment is about 110 degrees.
5If fine adjustment of the tilt angle is unnecessary, fasten the 2
bolts (M6) with the specified amount of torque, and fix the cap.
5
Fasten the sunshade fixing screws after adjustment.
4-2 Finely adjust the tilt angle direction of the camera
6 Rotate the sunshade to a suitable position, and
4
Tilt angle
Cover
fasten the screw on the bottom of the camera.
Note
1,5
4-2
direction
•
Do not hold the lens
Screw
section when adjusting the
direction of the camera.
Applying force to the zoom
adjustment ring while
adjusting the image size
may result in damage.
Dustproofing, waterproofing
Cap
Sunshade
4
Stay cover
Perform dustproofing and waterproofing
Rotation angle
Bolt (M6, 2-places)
For dustproofing, insert sealing material (GE silicon) into
the cable extracting space and gaps of the mounting
bracket, as well as the center hole of the stay cover.
Sealing material
6
4-2
2,4
4-2
Bolt (M4)
6 Rotate the sunshade. (When the camera is
1Loosen the screw on the right side of the Stay Cover, and open
the cover.
mounted on the wall only)
Rotate the sunshade after adjustment of the rotation angle. The
procedure is below.
2Loosen the bolt (M4) with torque wrench.
3Take the sunshade, and adjust the tilt angle. The range of
adjustment is limited within 20 degrees (approx.).
Rotation the
direction of the
sunshade
4Fasten the bolt (M4) with the specified amount of torque.
5
Set the cover on the stay cover opened in step 1, and fasten the screw.
6Securely fasten the 2 bolts (M6) that you fastened temporarily
1Loosen the screw at the
6
with the specified torque at 4 of step 4-1, and put on the cap.
bottom of the camera,
Note
and rotate the sunshade.
•
Fine adjustment of the tilt angle should be done when the bolt (M4)
is loose. If you adjust the tilt when the bolt is tightened, the bolt may
become loose.
2Fasten the screw after
Screw
the adjustment.
2
Note
• After adjusting the tilt angle and deciding the tilt position, make sure
to tighten the bolts (M6 and M4) on both sides of the stay cover to
the torque specified below.
1
• Do not loosen the screw on the bottom of the camera. Loosening
or removing it may lead to water and moisture getting inside and
fogging the lens and the front cover.
-M6: Greater than 3.93 N•m; M4: Greater than 0.98 N•m
3
☞ Continued overleaf
Cables
Troubleshooting
Cable type
Color
Red
Black
Signal name
AC 24 V
AC 24 V
INPUT 1 (ALARM)
INPUT 2 (ALARM)
OUTPUT 1 (ALARM)
OUTPUT 2 (ALARM)
GND (ALARM)
MIC IN
Symptom
Causes and Countermeasures
1
1Power cable
2Audio/Alarm cable
3LAN cable
Movement of network image is not • If the monitor image output is turned ON, a lower frame rate is set for
smooth
network images.
2
Brown
Red
• If you turned the monitor image output to OFF, set the frame rate
again.(☞ “Instructions (Setting)” - “Internet Explorer Setting” -
“Encoding Page”)
3
Alarm
Orange
Yellow
Black
White
Black
No monitor image is output.
The image output may be turned Off on Internet Explorer.
Check the monitor output setting.
GND (MIC IN)
The external mic sound is not
heard.
• Check the MIC connection.
• Is the audio setting turned off? (☞ “Instructions (Setting)” - “Audio
Audio
Black
Light Green LINE OUT
Black
GND (LINE OUT)
10BASE-T/
100BASE-TX
Page”)
RJ-45
Lens is out of focus
Is the focus adjustment gear engaged? Check the location of the catch.
(Shielded cable)
● Connecting the power cable to AC 24 V source
● LAN cable
• When connecting to a switching hub:
Use a straight cable.
• When connecting to a computer:
Use a crossing cable.
Conductor
diameter (mm)
1.0 mm dia 1.6 mm dia 2.0 mm dia
or more
or more
or more
Max cable
distance (meters)
(Reference value)
90
240
370
Specifications
•
A 100-meter or less length and Category-5 or higher
grade STP (shielded) cable is recommended.
Note
*
The specifications and appearance of this unit are subject to change for purposes of improvement without prior notice.
Note
• For safety reasons, turn on the power only after
confirming that all the connections are completed.
Image sensor
1/3-inch Square-Pixel Progressive Scan CMOS (elementary color filter)
• The crossing cable may not be used for some
computer models. Check the LAN specifications of
the computer when you directly connect this unit to
the computer.
Approximately 2,120,000 pixels
1944 (H) × 1092 (V)
•
•
Be sure to turn off the camera before connecting cables.
If you use both the AC 24 V power cable and the
PoE-based LAN cable simultaneously, the camera
may fail. Always supply power using either method.
To use an AC 24 V power supply, remove the
factory-installed tape from the power cable, connect
to an AC 24 V power supply, and wrap the connector
with new insulation tape and waterproof tape.
Effective pixels
Camera
section
(50%, AGC High, 1/30 s)
Color: 0.3 lx (typ.)
Black and White 0.03 lx (typ.)
Minimum illuminance
of subject
● Alarm cable
• A 50-meter or less length shielded cable is
recommended.
•
75 Ω, 1.0 Vp-p
NTSC or PAL (switch selectable)
Can connect to a microphone that has a plug-in power system
DC2.47 V(typ.)
Monitor output
Input
Audio input Reference voltage
Impedance
2.2 kΩ (typ.)
Audio output
Line OUT (200 Ω, Max 1.9 Vp-p)
Image compression
format
JPEG, H.264 High Profile, H.264 Baseline Profile, MPEG-4
Audio cable connection
1920 x 1080
1280 x 960
1280 x 720
640 x 480
640 x 360
320 x 240
Connect the audio cable for an audio device.
Audio cable (White and Black) (MIC IN)
Frame size
Network
: Connect to a condenser microphone that has a plug-in
power system, etc.
output
Audio cable (Light Green and Black) (LINE OUT) : Connect to a speaker with a built-in amp, etc.
Audio compression
formats
Memo
μ-Law(64 kbps), AD/DA 16bits, Fs = 8 kHz, monaural
• A shielded audio cable is recommended.
RJ-45
Network interface
100BASE-TX/10BASE-T/FULL/HALF/Auto-negotiation enabled
No-voltage a contact input, PNP open collector input, low level,
latch/momentary (500 msec or longer) (1 mA circuit current at low
level, and 3.3 VDC applied voltage at high level)
NPN open collector-output (16 VDC safe excitation voltage, and
30 mA allowable sink current)
16 MB
f = 3 mm to 9 mm
Alarm input
Alarm cable connection
Alarm output
Alarm input
Alarm output
Alarm record
Connect an infrared sensor, door sensor, metal
sensor, a manual switch or other device.
Connect an alarm device, indicator, lighting, buzzer or
other device.
Focal length
Maximum aperture
ratio
Aperture range
Zoom ratio
Standards
Communication
protocol
• To avoid noise entering the internal circuit, enter the • An alarm output signal is an open collector output.
F 1.2 (f =3 mm) to F 2.1 (f =9 mm)
Lens
non-voltage contact signal in the Alarm IN terminal.
• Do not supply voltage.
• The alarm can be set to be activated during close
contact (MAKE) or during open contact (BREAK)
can be set from the menu.
• The alarm signal should last for at least 500
msec. If the alarm signal is short, it may not be
recognized.
You can configure the menu to set the alarm to
sound when contacts short circuit (MAKE) or
when the contacts are open (BREAK). (Pressure
resistance lower than 16V, 30 mA)
• This terminal has different polarities. The output
voltage at the positive terminal must always be
higher than the output voltage at the negative
terminal. Otherwise, the circuit may be damaged.
F 1.2 to F 360
3 x
Compliant with IEEE802.3, IEEE802.3u and IEEE802.3af
TCP/IP, UDP/IP, FTP, ICMP, ARP, DHCP, SNTP, HTTP, SMTP, RTP,
RTSP, IPv4, IPv6, DSCP, HTTPS, SNMP
LAN
standards
Power supply voltage AC24 V 50 Hz/60 Hz, or PoE(DC-48 V)
Current consumption AC24 V 0.5 A, or PoE 150 mA (7.2 W)
-10 °C to 50 °C (Operation)
0 °C to 40 °C (Recommended)
20 %RH to 90 %RH (without condensation)
Approx. 1.8 kg
● Input conditions
• Connect non-voltage a contact or NPN open
collector output circuit
(For details on how to set polarities, please refer to
“Instructions (Setting)”.)
• Low level terminal current below 1 mA
• High level terminal current 3.3 V
This
● Output conditions
Ambient temperature
General
• Equivalent to NPN open collector output
(For details on how to set the output logic, please
refer to “Instructions (Setting)”.)
• Safe excitation voltage: DC12 V or lower
• Allowable surge current: 50 mA
• Momentary (100 ms to 5000 ms) output
(For details on how to set the time, please refer to
“Instructions (Setting)”.)
Ambient humidity
Mass
Dustproof/Waterproof IP66 compliant
Sensor example (1)
camera
DC3.3 V
Alarm device
example
VCC
Input 1 or
Input 2
This
camera
R
OUT
DC12 V
Output 1 or
Output 2
3.3 V 1 mA
G
External dimensions (unit: mm)
R
IN
G
(Alarm input equivalent circuit)
Sensor example (2)
Relay switch or
other devices
G
G
(Alarm output equivalent circuit)
OUT
Note
G
• Connect the G terminal cable of this camera to the
GND of the alarm device.
257.5
Ø140
184.5
(Maximum shade extention)
214.5
LST1238-001B
4
|