VIDEO CASSETTE RECORDER
HR-A5U
INSTRUCTIONS
LPT0588-001A
COPYRIGHT © 2001 VICTOR COMPANY OF JAPAN, LTD.
Printed in China
0301 IYVfIDfBJ
Dear Customer,
CAUTION:
Thank you for purchasing the JVC VHS video cassette recorder.
Before use, please read the safety information and precautions to
ensure safe use of your new VCR.
Changes or modifications not approved by JVC could void
user’s authority to operate the equipment.
Declaration of Conformity
CAUTIONS
Model Number:
Trade Name:
HR-A5U
JVC
Responsible Party: JVC Americas Corp.
Address:
1700 Valley Road Wayne, N.J. 07470
Telephone Number: 973-315-5000
This device complies with Part 15 of FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation.
The lightning flash with arrowhead symbol, within
an equilateral triangle, is intended to alert the user
to the presence of uninsulated “dangerous voltage”
within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric
shock to persons.
Failure to heed the following precautions may result in damage
to the VCR, Remote or video cassette.
1. DO NOT place the VCR …
… in an environment prone to extreme temperatures or
humidity.
… in direct sunlight.
… in a dusty environment.
The exclamation point within an equilateral triangle
is intended to alert the user to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying the
appliance.
… in an environment where strong magnetic fields are
generated.
… on a surface that is unstable or subject to vibration.
2. DO NOT block the VCR’s ventilation openings.
3. DO NOT place heavy objects on the VCR or on the Remote.
4. DO NOT place anything which might spill on the top of the
VCR or on the Remote.
WARNING:
5. AVOID violent shocks to the VCR during transport..
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE
THIS UNIT TO RAIN OR MOISTURE.
For Customer Use:
CAUTION:
Enter below the Model No. and Serial No. which are located
on the rear of cabinet. Retain this information for future
reference.
This video cassette recorder should be used with AC 120Vd,
60Hz only.
To prevent electric shocks and fire hazards, DO NOT use any
other power source.
Model No.
Serial No.
CAUTION:
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF
PLUG TO WIDE SLOT, FULLY INSERT.
ATTENTION:
POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA
LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE
CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU
FOND.
● Cassettes marked “VHS” (or “S-VHS”) can be used with this
video cassette recorder. However, S-VHS recording is not
possible with this model.
● This model is equipped with SQPB (S-VHS QUASI PLAYBACK)
that makes it possible to play back S-VHS recordings with
regular VHS resolution.
● HQ VHS is compatible with existing VHS equipment.
● As an ENERGY STAR® Partner, JVC has determined that this
product or product model meets the ENERGY STAR® guidelines
for energy efficiency.
Note to CATV system installer:
This reminder is provided to call the CATV system installer’s
attention to Article 820-40 of the NEC that provides guidelines
for proper grounding and, in particular, specifies that the cable
ground shall be connected to the grounding system of the
building, as close to the point of cable entry as practical.
SERVICING
1. Servicing
Buttons, Connectors
and Indicators
If your product is not operating correctly or exhibits a marked
change in performance and you are unable to restore normal
operation by following the detailed procedure in its operating
instructions, do not attempt to service it yourself as opening or
removing covers may expose you to dangerous voltage or other
hazards. Refer all servicing to qualified service personnel.
2. Damage Requiring Service
Unplug this product from the wall outlet and refer servicing to
qualified service personnel under the following conditions:
a. When the power supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the
product.
Front Panel
Cassette
loading slot
c. If the product has been exposed to rain or water.
d. If the product does not operate normally by following the
operating instructions. Adjust only those controls that are
covered by the operating instructions as an improper
adjustment of other controls may result in damage and will
often require extensive work by a qualified technician to
restore the product to its normal operation.
e. If the product has been dropped or damaged in any way.
f. When the product exhibits a distinct change in performance—
this indicates a need for service.
VIDEO/AUDIO
input connectors
Remote
sensor
3. Replacement Parts
When replacement parts are required, be sure the service
technician has used replacement parts specified by the
manufacturer or which have the same characteristics as the
original part. Unauthorized substitutions may result in fire,
electric shock or other hazards.
Display panel
Timer mode indicator
VCR mode
indicator
Play indicator
Record
indicator
4. Safety Check
Upon completion of any service or repairs to this product, ask the
service technician to perform safety checks to determine that the
product is in safe operating condition.
Channel and auxiliary input/Clock time
How to use the Remote
Before use, insert two AA size batteries into the Remote with the
polarity ( and ) matched correctly as indicated on the battery
compartment or on the lid.
The Remote can operate most of your VCR’s functions, as well as
basic functions of TV sets, cable boxes and DBS receivers.
● Point the Remote toward the remote sensor on the target
component.
Rear Panel
AC power cord
● The maximum operating distance of the remote control is about
8 m.
NOTE:
If the Remote does not work properly, remove its batteries, wait for
a few seconds, replace the batteries and then try again.
Video heads cleaning
Use a dry cleaning cassette — TCL-2UX — when:
● Rough, poor picture appears while a tape is played back.
● The picture is unclear or no picture appears.
● “USE CLEANING CASSETTE” appears on the screen (only with
“SUPERIMPOSE” set to “ON”).
– Buttons, Connectors and Indicators –
Remote
Connections and
Plug&Play Setting
A Check contents
Make sure the package contains all of the accessories listed in
“Specifications”.
Number keys
B Situate VCR
Place the VCR on a stable, horizontal surface.
C Connect VCR to TV
RF Connection
A Disconnect the TV antenna from the TV.
B Connect the TV antenna cable to the ANT. IN terminal on the
rear of the VCR.
C Connect the supplied RF cable between the TV OUT terminal
on the rear of the VCR and the TV’s antenna input terminal.
AV Connection
(improves picture quality during tape playback.)
If your TV is equipped with audio/video input connectors
A Connect the antenna, VCR and TV as shown in the illustration.
B Connect an audio/video cable between the AUDIO/VIDEO
OUT connectors on the rear of the VCR and the audio/video
input connectors on the TV.
● Even if you are using audio/video cables to connect your VCR to
your TV, you must also connect it using the RF cable. This will
ensure that you can record one show while watching another.
On-screen display
If you press OSD on the Remote when “SUPERIMPOSE” is set to
“ON”, you can see the current VCR status on the TV screen. Press
OSD again to exit on-screen display.
The indications are not recorded even if the VCR is in the
recording mode.
A
L
CH125
RECORD
PAUSE
SP
K
J
I
H
G
F
THU 12:00 AM
B
C
D
STEREO –WARNING–
SAP TIMER RECORDING
TO START SOON
(CANCEL)
+
+
+
E
1
B
INDEX
NORM
HI-FI
E
COUNT
–1:23:45
A Channel and auxiliary input
B Day and clock time
C STEREO program indication
D SAP indication
E Audio monitor indications
F Time counter
G Index number
H Tape position
I Cassette mark
J Tape speed
K VCR operation mode
L Timer warning display
– Connections and Plug&Play Setting –
E Set VCR channel
Antenna or cable
Coaxial cable
The VCR channel is the channel on which you can watch the
picture from the VCR on the TV when only using the RF
connection. Press POWER to turn off the VCR, then press STOP/
EJECT (0) on the VCR for more than 5 seconds. “CH3”
appears on the display panel. Press CH+/– on the Remote to
select “CH3”, “CH4” or “CH–”(OFF), then press OK.
● The VCR channel is preset to “CH3”. Set to “CH4” if CH3 is
used for broadcasting in your area.
Flat feeder
Matching transformer
(not supplied)
F Final preparation for use
Turn on the VCR and the TV, and select the VCR channel 3 or 4
(or AV mode) on the TV. You can now perform basic playback or
basic recording.
AC power cord
Initial Settings
Back of VCR
AC outlet
Language Setting
The default setting is “ENGLISH”.
To audio/video
input connectors
MAIN MENU
A Access Main Menu screen, then
FUNCTION SET
Initial Set screen
TUNER SET
INITIAL SET
Press MENU on the Remote. Press rt to
Audio/video cable
(not supplied)
move the highlight bar (arrow) to “INITIAL
SET”, then press OK or e.
PRESS (
,
), THEN (OK)
PRESS (MENU) TO END
B Select language
INITIAL SET
CLOCK SET
RF cable
To 75 ⍀ terminal
TV
This VCR offers you the language choice to
view menus and some messages — in
English, Spanish or French. Press rt to
move the highlight bar (arrow) to
“LANGUAGE”, then press OK or e
repeatedly until the desired language is
selected.
(supplied)
LANGUAGE
ENGLISH
GUIDE CHANNEL SET
D Perform Plug&Play setup
Plug the AC power cord into an AC outlet. Do not turn on the
VCR. The clock and tuner channels will be set automatically. The
time and date can be set automatically by the clock setting data
transmitted from one of the regular TV broadcast channels. We
call this TV channel the “host channel” and it is a PBS channel in
your area.
SELECT WITH (
,
) AND (OK)
PRESS (MENU) TO END
Press MENU to return to normal screen.
ATTENTION:
Clock Setting
If you use a cable box, Plug&Play will not function; set the clock
and tuner channels separately.
Perform clock setting only if the clock has not been set correctly
by the Plug&Play setting or if you use a cable box.
During Initial Auto Clock Set
“Aut” blinks.
Preparations
During Auto Channel Set
The channel numbers are displayed as they are
scanned and set.
MAIN MENU
A Access Main Menu screen, then
FUNCTION SET
Initial Set screen
TUNER SET
INITIAL SET
Press MENU on the Remote. Press rt to
Plug&Play Completed
The current time is displayed.
move the highlight bar (arrow) to “INITIAL
SET”, then press OK or e.
PRESS (
,
), THEN (OK)
PRESS (MENU) TO END
B Access Clock Set screen
What to do if Plug&Play setting failed
INITIAL SET
CLOCK SET
● If an incorrect time is displayed on the display panel, perform
the “Semiauto Clock Set” or “Manual Clock Set” procedure.
● If “–:– –” appears on the display panel, ensure that the antenna
cable is connected correctly. Then turn on and off the VCR; the
Plug&Play setting will be automatically reactivated. If Plug&Play
setting is not performed though the antenna cable is connected
correctly, perform “Manual Clock Set” and “Auto Channel Set”
or “Manual Channel Set”.
Press rt to move the highlight bar (arrow)
LANGUAGE
ENGLISH
to “CLOCK SET”, then press OK or e.
GUIDE CHANNEL SET
SELECT WITH (
,
) AND (OK)
PRESS (MENU) TO END
Setting clock semiautomatically
— Semiauto Clock Set
You can change the host channel/D.S.T. (Daylight Saving Time)/
time zone setting manually. First follow steps 1 to 2 in
“Preparations” above, then go to the following steps.
NOTE:
The time set previously will be erased when “AUTO CLOCK”,
“HOST CH”, “D.S.T.” or “TIME ZONE” setting is changed.
– Initial Settings –
CLOCK SET
A Set Auto Clock to ON
Tuner Setting
TIME
DATE
12/24
YEAR
Press OK or e on the Remote repeatedly to
move the highlight bar to “AUTO CLOCK”,
then press rt so that “ON” is selected.
1:00PM
00 SUN
AUTO CLOCK : ON
HOST CH
D.S.T.
: AUTO
: AUTO
(CATV)
Setting channels automatically
— Auto Channel Set
TIME ZONE : AUTO
PRESS (
,
), THEN (OK)
PRESS (MENU) TO END
B Select host channel
Perform Auto Channel Set only if channels have not been set
correctly by the Plug&Play setting.
You can either select “AUTO” or enter a PBS channel number.
Press OK or e to move the highlight bar to “HOST CH”, then
press rt repeatedly until “AUTO” or the desired PBS channel
number is selected.
MAIN MENU
A Access Main Menu screen, then Tuner
FUNCTION SET
Set screen
TUNER SET
INITIAL SET
Press MENU on the Remote. Press rt to
C Select D.S.T. mode
move the highlight bar (arrow) to “TUNER
Press OK or e to move the highlight bar to “D.S.T.”, then press
rt repeatedly until the desired setting is selected.
AUTO: Select if you want to adjust your VCR’s clock
automatically by the incoming signal from the host
channel. (Auto Daylight Saving Time enables automatic
adjustment of the VCR’s clock at the start and end of
Daylight Saving Time.) Be sure to select the correct time
zone manually in step 4.
SET”, then press OK or e.
PRESS (
,
), THEN (OK)
PRESS (MENU) TO END
B Perform Auto Channel Set
TUNER SET
BAND
CATV
Press rt to move the highlight bar (arrow)
to “AUTO CHANNEL SET”, then press OK
or e. The VCR selects the correct band (TV
or CATV) automatically during Auto
Channel Set.
AUTO CHANNEL SET
MANUAL CHANNEL SET
SELECT WITH (
,
) AND (OK)
ON:
OFF:
Adjustment will be made by the built-in clock itself.
Select when Daylight Saving Time does not apply to you.
PRESS (MENU) TO END
● When Auto Channel Set is complete,
“SCAN COMPLETED” appears on
screen.
AUTO CHANNEL SET
D Select time zone
Press OK or e to move the highlight bar to “TIME ZONE”, then
press rt repeatedly until “AUTO” or the desired time zone is
selected. Each time you press the button, the time zone changes
as follows:
● If the scan was unsuccessful, “SCAN
COMPLETED–NO SIGNAL–” appears
on screen. Check the connections and
start again.
SCANNING...
PRESS (MENU) TO END
{ AUTO { ATLANTIC { EASTERN { CENTRAL
{ MOUNTAIN { PACIFIC { ALASKA { HAWAII
{ (back to the beginning)
Press MENU to return to normal screen.
Setting channels manually
— Manual Channel Set
E Complete Semiauto Clock Set
Press MENU to return to normal screen. Turn off the VCR. “Aut”
will appear on the display panel while the clock is being set. The
current clock time will appear automatically when the clock
setting is complete.
You can add the channels you want or delete the channels you do
not want manually.
MAIN MENU
A Access Main Menu screen, then Tuner
FUNCTION SET
Set screen
TUNER SET
INITIAL SET
Setting clock manually
— Manual Clock Set
Press MENU on the Remote. Press rt to
move the highlight bar (arrow) to “TUNER
SET”, then press OK or e.
PRESS (
,
), THEN (OK)
First follow steps 1 to 2 in “Preparations” above, then go to the
PRESS (MENU) TO END
following steps.
B Access Manual Channel Set screen
Press rt to move the highlight bar (arrow)
to “MANUAL CHANNEL SET”, then press
OK or e.
TUNER SET
CLOCK SET
BAND
CATV
A Set time, date and year
Press rt until the desired time appears,
then press OK or e. Set the date and year
in the same way.
● Holding rt changes the time in 30-
minute intervals, or changes the date in
15-day intervals.
AUTO CHANNEL SET
MANUAL CHANNEL SET
TIME
– –:– –AM
DATE
1/
YEAR
00
1
AUTO CLOCK : ON
HOST CH
D.S.T.
: AUTO
: AUTO
TIME ZONE : AUTO
(CATV)
SELECT WITH (
,
) AND (OK)
PRESS (MENU) TO END
PRESS (
,
), THEN (OK)
PRESS (MENU) TO END
MANUAL CHANNEL SET
C Add or skip desired channels
To add channels
(CATV)
CH 45 ADD
A Press the Number keys on the Remote
to input a channel number you want to
add.
B Press OK or e to set to “ADD”.
C Repeat A to B to add other channels.
Press MENU to return to normal screen.
To skip channels
A Press rt or the Number keys to select a channel number you
want to skip.
B Press OK or e to set to “SKIP”.
CLOCK SET
B Select D.S.T. mode
Press OK or e to move the highlight bar to
“D.S.T.”, then press rt to select the
desired setting.
ON: Adjustment will be made by the
built-in clock itself.
OFF: Select when Daylight Saving Time
does not apply to you.
TIME
1:00AM
DATE
YEAR
00 SUN
PRESS NUMBER KEY (0–9)
12/ 24
OR (
,
), THEN (OK)
AUTO CLOCK : OFF
PRESS (MENU) TO END
D.S.T.
: ON
PRESS (
,
), THEN (OK)
PRESS (MENU) TO END
C Start clock
Press MENU and normal screen appears.
C Repeat A and B to skip other channels. Press MENU to return
to normal screen.
To make corrections any time during the process
Press OK or e repeatedly until the item you want to change
blinks, then press rt.
When the tape is not running
Rewind/fast-forward at high speed
Press REW (3) or FF (5).
Eject the tape
Playback
Basic Playback
A Load a cassette
Press STOP/EJECT (0).
● You can also eject the cassette when the VCR is turned off.
Turn off the VCR
Press POWER.
Playback Features
Adjusting tracking condition
— Tracking Adjustment
Make sure the window side is up, the rear label side is facing you
and the arrow on the front of the cassette is pointing towards the
VCR.
● Do not apply too much pressure when inserting.
● The VCR turns on, and the counter on the on-screen display is
reset, automatically.
Automatic tracking adjustment
Whenever you insert a tape and start playback, automatic tracking
starts working and continuously analyzes the signal to enable
optimum picture quality during playback.
Manual tracking adjustment
If automatic tracking cannot eliminate noises well during
playback, follow the procedures below.
● If the cassette’s record safety tab has been removed, playback
begins automatically.
B Start playback
Press PLAY (4).
A Press SP/EP on the Remote during playback to activate manual
tracking.
B Press CH + and – to eliminate the noises. Press it briefly for a
During playback
fine adjustment, or press and hold for a coarse adjustment.
C Press SP/EP on the Remote again to reactivate automatic
Stop playback
tracking.
Press STOP (8) on the
Remote.
OR Press STOP/EJECT (0) on
the VCR.
Selecting monitor sound
— Audio Monitor
Pause playback and view still picture
Press PAUSE (9).
● Press PLAY (4) to resume normal playback.
While playing back a tape on which stereo sound or SAP sound is
recorded, press A. MONITOR on the Remote. Each time you press
the button, sound changes.
Pause and Frame-by-Frame playback
HI-FI: Normally select this. Hi-Fi sound is played back.
HI-FI L: Sound on the left Hi-Fi channel is played back.
HI-FI R: Sound on the right Hi-Fi channel is played back.
NORM: Sound on the normal track is played back.
NORM HI-FI: Both sounds on the Hi-Fi track and normal track are
mixed and played back.
Press PAUSE (9) to pause, then press 6 (or PAUSE (9))
repeatedly.
● Press PLAY (4) to resume normal playback.
Rewind/fast-forward
Press REW (3) or FF (5).
● Press PLAY (4) to resume normal playback.
● If you press and hold REW (3) or FF (5) for more than
2 seconds, simply releasing it cancels the picture search, and
normal playback resumes.
NOTE:
The above indication appears when “SUPERIMPOSE” is set to
“ON”, though the monitor sound changes in sequence.
Rewind/fast-forward at variable speed (including slow-motion)
Automatic operations after rewinding
— Next Function Memory
Press 2 or 6 repeatedly.
● Press PLAY (4) to resume normal playback.
The Next Function Memory “tells” the VCR what to do after
rewinding is complete. Ensure that the VCR is in stop mode.
● For Automatic Playback Start
● Each time you press 2 or 6, the playback speed changes.
To decrease the speed during picture search, press the opposite
direction button repeatedly.
● During still picture, press and hold 6 to start forward slow
motion playback. When you release the button, still picture
resumes. During still picture, holding PAUSE (9) for more than
2 seconds also starts forward slow motion playback. If you
press PAUSE (9) again, still picture resumes.
Press REW (3), then press PLAY (4) within 2 seconds.
● For Automatic Power Off
Press REW (3), then press POWER within 2 seconds.
● For Automatic Timer Standby
Press REW (3), then press TIMER within 2 seconds.
NOTE:
It is not possible to select the Automatic Timer Standby function if
the cassette’s record safety tab is removed.
Reverse
Forward
Reverse
search
3 steps
Reverse
play
Slow
motion
1 step
Normal Forward
play
search
4 steps
– Playback –
Playing back tape repeatedly (100 times)
— Repeat Play
Recording
It may be unlawful to record or play back copyrighted material
without the consent of the copyright owner.
During playback, press and hold PLAY (4) for more than
5 seconds. The play indicator ($) on the display panel starts
blinking slowly. To stop playback, press STOP (8) on the Remote
or STOP/EJECT (0) on the VCR.
Accidental erasure prevention
To prevent accidental recording on a
recorded cassette, remove its record
safety tab. To record on it later, cover
Locating beginning of recordings
— Index Search
the hole with adhesive tape.
Record safety tab
Index codes are placed on the tape at the beginning of each
recording when recording on this VCR.
Basic Recording
A Load a cassette
A While the tape is not running, press SHUTTLE PLUS 2 or
6 on the Remote to start search.
B To access a recording of 2 to 9 index
codes away, press 2 or 6
Make sure the record safety tab is intact. If not, cover the hole
with adhesive tape before inserting the cassette.
repeatedly until the correct number is
displayed on the screen (only if
“SUPERIMPOSE” is set to “ON”).
Playback begins automatically when
the desired recording is located.
● The VCR turns on, and the counter is reset, automatically.
B Select recording channel
On the Remote
Press CH+/– or the Number keys.
On the VCR
INDEX
1
Press PAUSE[CH]. The channel display on the
display panel starts blinking. While the display is
blinking, press FF[CH+] or REW[CH–] to select
channel. After about 5 seconds, the channel display
stops blinking.
Beginning of the
current program
recorded
Beginning of the
2nd next program
recorded
Current
position on
the tape
Previous
program
recorded
Next
program
recorded
2nd next
NOTES:
● You can select channel in the stop mode,
recording pause mode or during rewind/fast-
forward high-speed search.
● If no cassette is loaded, or during recording pause
mode, you can select channel only by pressing
FF[CH+] or REW[CH–].
● If you connect the TV and the VCR only using the
RF connection, press TV/VCR on the Remote so
that the VCR mode indicator lights on the display
panel, to view the program to be recorded.
Locating beginning of timer recordings
— Instant Review
Press REVIEW on the Remote after ensuring that the VCR is turned
off and that the timer mode is disengaged.
C Set tape speed
Press SP/EP.
● The VCR turns on, and rewinds to the index code indicating the
beginning of the last timer-recorded program, then begins
playback automatically.
● You can access a program of 2 to 9 index codes away from the
current position on the tape. If, for example, you have
5 programs recorded and you want to watch the third one, press
REVIEW three times.
D Start recording
On the VCR, press REC (7). Or on the Remote, while holding REC
(7), press PLAY (4).
● The Instant Review function will also operate if the VCR is
turned on.
During recording
Pause recording
Skipping unwanted portions
— Skip Search
Press PAUSE (9).
● Press PLAY (4) to resume recording.
● You can select channel in the recording pause mode.
Press SKIP SEARCH on the Remote once to 4 times during
playback. Each press initiates a 30-second period of high speed
playback (up to 2 minutes). When the specified portion of the tape
is skipped, normal playback resumes automatically. To return to
normal playback during Skip Search, press PLAY (4).
Stop recording
Press STOP (8) on the
Remote.
OR Press STOP/EJECT (0) on
the VCR.
– Recording –
Recording Features
Timer Recording
Up to 8 timer recording programs can be made using Express
timer programing method as far as a year in advance. Remember,
the clock must be set before you can program the timer.
Specifying recording length
— Instant Timer Recording (ITR)
NOTES:
During recording, press REC (7) on the VCR repeatedly until the
recording length you want appears on the display panel. The
record indicator (⅜) on the display panel starts blinking.
● Each time you press the button, recording length increases in
30-minute intervals (up to 6 hours).
● If all the 8 programs have already been set, “PROGRAM FULL”
or “Full” appears on the TV screen or the display panel.
● After timer recording is completed, the VCR turns off
automatically.
● You can program the timer recording while a regular recording
is in progress; the menu screens will not be recorded.
● To timer-record cable or satellite channels, be sure to keep the
cable box or DBS receiver turned on with the correct channel
selected.
● Even if a power failure occurs, the VCR keeps your timer
programs. However, the clock time, channel settings, and other
menu settings are lost. As a result, when the power is supplied
again to this VCR after the power failure, this VCR starts the
Plug&Play setting automatically to restore the clock time and
channel setting. If the clock time and channel setting are
restored correctly, each timer program you have made will start
at its start time unless its end time has elapsed.
● The VCR shuts off after recording is finished.
● To cancel an ITR, press STOP (8) on the Remote or STOP/EJECT
(0) on the VCR.
Watching one program while recording another
During recording…
● If you connect the TV and the VCR only using the RF
connection to view pictures from the VCR, press TV/VCR on the
Remote so that VCR mode indicator goes off from the display
panel. (The TV broadcast being recorded disappears.)
● If you are using the AV connection to view pictures from the
VCR, change the TV’s input mode from AV to TV.
Then, select the channel you want to watch, on the TV.
Second Audio Recording
Express Timer Programing
This VCR’s built-in MTS decoder enables reception of
Multichannel TV Sound broadcast. To record a SAP program
received, set “2ND AUDIO RECORD” to “ON”.
Load a cassette with the record safety tab intact. The VCR turns
on, and the counter is reset, automatically.
A Press PROG. on the Remote to access the PlusCode No.
screen.
B Press START+/– once to access
PROGRAM 1
Program screen. Press START+/–,
START
– –:– –AM
DATE
STOP
– –:– –AM
CH
STOP+/–, DATE+/– or CH+/–
repeatedly to enter the start time, stop
time, date or channel.
– –/– –/– –
– – – SP
PRESS (+/–, SP/EP, 8=DAILY
9=WEEKLY), THEN (0K)
PRESS (PROG.) TO END
● Press and hold START+/– or
STOP+/– to increase the time in
30-minute intervals.
● To set the tape speed, press SP/EP.
● To timer-record daily (Monday–Friday) or weekly serials,
press DAILY (M-F) or WEEKLY. Pressing the button again
makes the “DAILY” or “WEEKLY” display disappear.
– Timer Recording –
C Press OK or PROG..
Program overlap warning display
● If “PROGRAM NOT COMPLETED PROGRAM OVERLAP”
appears, see “Program overlap warning display”.
If “PROGRAM NOT COMPLETED PROGRAM OVERLAP”
appears, you have another program overlapping the program you
have just made. The Program Check screen appears and
conflicting programs will start blinking.
D Press TIMER. The VCR turns off automatically and “#” is
displayed on the display panel.
PR START STOP CH DATE
1
2
3
4
5
6
7
8
8:00P 10:00 12 12/24
10:00A 10:45 40 12/25
To use the VCR while it is in timer
recording standby mode
PROGRAM NOT COMPLETED
PROGRAM OVERLAP
11:30P
1:00 125 12/25
9:00P 10:00 10 12/24
Press TIMER, then press POWER. After you use the VCR, press
(
,
), THEN (
)
(PROG.) : END
TIMER again to put the VCR into timer recording standby mode.
Example:
Program 1 (you have just made) and Program 4 overlap each
other
Checking, canceling or changing
program settings
A Select program to modify
PR START STOP CH DATE
1
2
3
4
5
6
7
8
8:00P 10:00 12 12/24
10:00A 10:45 40 12/25
Press rt, then press e.
11:30P
1:00 125 12/25
● You can only select one of the
overlapping programs.
● If you do not mind this overlap, press
PROG. to finish the timer program
setting. The program starting earlier or
9:00P 10:00 10 12/24
A Disengage timer
Press TIMER, then press POWER.
(
,
), THEN (
)
(PROG.) : END
● When “AUTO TIMER” is set to “ON”, you do not have to press
TIMER.
program with the lower program number will be recorded.
B Access Program Check screen
PR START STOP CH DATE
PROGRAM 4
B Cancel or change program setting
1
2
3
4
5
6
7
8
8:00P 10:00 12 12/24
10:00A 10:45 40 12/25
Press PROG. CHECK.
START
9:00PM
DATE
12/24/00
SUN
STOP
10:00PM
CH
To cancel a program, press CANCEL when
the Program screen you do not want is
shown.
11:30P
1:00 125 12/25
10 SP
PRESS (CANCEL) TO CANCEL
PRESS (OK) TO CONFIRM
PRESS (PROG.) TO END
To change a program, press the
appropriate button: START+/–, STOP+/–,
DATE+/–, CH+/–, and/or SP/EP when the
PRESS (CHECK) TO NEXT
PROGRAM 1
C Access Program screen
Press PROG. CHECK again. Each time you
press PROG. CHECK, the next program’s
Program screen appears.
Program screen on which you want to make changes is shown,
then press OK.
● If the overlap is not yet solved, the conflicting programs will be
shown on the Program check screen. Repeat the above steps
again.
START
8:00 PM
DATE
STOP
10:00 PM
CH
12/24/00
12 SP
PRESS (CANCEL) TO CANCEL
PRESS (CHECK) TO NEXT
D Cancel or change program setting
To cancel a program, press CANCEL when the Program screen
you do not want is shown.
To change a program, press the appropriate button: START+/–,
STOP+/–, DATE+/–, CH+/–, and/or SP/EP when the Program
screen on which you want to make changes is shown.
E Return to normal screen
Press PROG. CHECK repeatedly until no Program screen is
shown.
F Reengage timer recording standby mode
Press TIMER. The VCR turns off automatically and “#” is
displayed on the display panel.
● When “AUTO TIMER” is set to “ON”, the timer recording
standby mode automatically resumes when you turn off the
VCR.
C Change setting
Other Functions
Press OK or e. The default setting is bold in the following table.
Press MENU to return to normal screen.
Ⅵ AUTO PICTURE — ON/OFF
When this function is set to “ON”, this VCR checks the condition
of the tape in use during playback, and compensates to provide
the highest-possible playback pictures.
Checking tape position
When you change the VCR operation
mode from the stop mode to fast forward
or rewind mode, or when you perform an
Index Search or Instant Review, the tape
+
+
+
E
B
position indicator appears.
Ⅵ PICTURE CONTROL — AUTO(NORM)/EDIT/SOFT/SHARP
This function helps you to adjust the playback picture quality
according to your preference.
AUTO (NORM): Normally select this. Picture quality is adjusted
automatically. When “AUTO PICTURE” is “OFF”, “NORM” will
appear instead of “AUTO”.
The position of “q” in relation to “B”
(Beginning) or “E” (End) shows you where
you are on the tape.
● Set “SUPERIMPOSE” to “ON”.
EDIT: Minimizes picture degradation during editing (recording and
playback).
SOFT: Reduces image coarseness when viewing overplayed tapes
containing much noise.
SHARP: Clearer, sharper-edged picture when viewing images with
much flat, same-colored surfaces such as cartoons.
Changing display information
Each time you press DISPLAY, the display panel
shows the channel number and the clock time
alternatively.
● You can change display in the stop, recording or
recording pause mode, or during rewind/fast-
forward high-speed search.
NOTE:
Select “EDIT” when you are editing tapes. After you finish editing
the tapes, select “AUTO”.
● When “SUPERIMPOSE” is set to “ON” and DISPLAY on the
Remote is pressed, time counter will appear on the TV screen.
To reset the time counter, press C. RESET on the Remote.
Ⅵ AUTO TIMER — ON/OFF
● When this function is set to “ON”:
The timer recording standby mode is automatically engaged when
the VCR is turned off. It is temporarily canceled when the VCR is
turned on. You do not have to press TIMER to engage or disengage
the timer recording standby mode.
Timer warning display
you that the timer-recording is to start in
5 minutes if you are not in the timer
recording standby mode at that time. Press
TIMER to put the VCR into timer recording
standby mode. To clear the display, press
CANCEL on the Remote.
A warning appears on the TV screen to tell
● When this function is set to “OFF”:
–WARNING–
TIMER RECORDING
You have to press TIMER to engage or disengage the timer
recording standby mode.
TO START SOON
(CANCEL)
Ⅵ
SUPERIMPOSE — ON/OFF
When this function is set to “ON”, various VCR status information
(on-screen display) appears on the screen.
NOTE:
Function settings
When you use this VCR as the playback VCR for editing a tape, be
sure to set this function to “OFF”; otherwise, the VCR status
information (on-screen display) will be recorded on the edited
tape.
You can use the other useful function settings on the Function Set
screen.
MAIN MENU
A Access Main Menu screen, then
FUNCTION SET
Function Set screen
TUNER SET
INITIAL SET
Ⅵ AUTO SP]EP TIMER — ON/OFF
Press MENU on the Remote. Press rt to
When this function is set to “ON”, the VCR automatically
switches to EP mode to allow complete recording if there is not
enough tape to record the entire program while timer-recording in
SP mode.
move the highlight bar (arrow) to
“FUNCTION SET”, then press OK or e.
PRESS (
,
), THEN (OK)
PRESS (MENU) TO END
B Select Function
For Example, Recording a program of 140 minutes in length onto
a 120-minute tape
Press rt to move the highlight bar (arrow) to the function you
want to set.
Approximately 110 minutes
Approximately 30 minutes
FUNCTION
PREVIOUS PAGE
BLUE BACK
AUTO PICTURE
ON
AUTO
OFF
ON
ON
OFF
SP mode
EP mode
PICTURE CONTROL
AUTO TIMER
SUPERIMPOSE
AUTO SP EP TIMER
VIDEO STABILIZER
NEXT PAGE
2ND AUDIO RECORD
AUDIO MONITOR
HI-FI
NOTES:
OFF
OFF
● If you have programed the VCR to timer-record 2 or more
programs, do not use this function, but change the tape speed
manually during timer programing.
SELECT WITH (
,
) AND (OK)
SELECT WITH (
,
) AND (OK)
PRESS (MENU) TO END
PRESS (MENU) TO END
● There may be some noise and sound disturbance where the tape
speed switches from SP to EP mode on the tape.
● This function is not available during ITR (Instant Timer
Recording), and will not work properly on the following tapes:
T(ST)-30, T(ST)-60, T(ST)-90, and T(ST)-120.
– Other Functions –
Ⅵ VIDEO STABILIZER — ON/OFF
When this function is set to “ON”, you can automatically correct
vertical vibrations in the picture when playing back unstable
recordings made on another VCR.
Multi-Brand Remote Control
This Remote can control some functions of remote controllable
TVs, cable boxes or DBS (Direct Broadcast Satellite) receivers
listed below. Without setting, you can control a JVC TV.
NOTE:
NOTES:
To watch recordings with close-caption or when you finish
viewing a tape, set this function to “OFF”.
● Some unit’s brands have more than one code. If the unit does
not function with a specified code, try other codes.
● Depending on the type of unit, some or all functions cannot be
operated using this Remote.
Ⅵ BLUE BACK — ON/OFF
When this function is set to “ON”, the TV screen becomes all blue
in the following cases:
● When receiving a channel not in use.
● When stopping playback.
● It’s not possible to operate a unit not equipped with a remote
sensor.
● It’s not possible to set the Remote for both your cable box and a
DBS receiver at the same time.
● Once you have set the Remote to operate the unit, you do not
have to set it until you replace the batteries from the Remote.
NOTE:
When you want to receive an unstable channel with poor signals,
set this function to “OFF”.
TV Brand Setting
Ⅵ 2ND AUDIO RECORD — ON/OFF
● When this function is set to “ON”;
A Turn on TV
Turn on the TV using the Power button on the TV or its Remote.
If a SAP program is received, the SAP audio is recorded on both
the normal and Hi-Fi tracks. The main audio is not recorded.
If a non-SAP program is received, the main audio is recorded on
both the Hi-Fi and normal tracks.
● When this function is set to “OFF”, the SAP audio cannot be
recorded.
B Set TV brand code
A Press and hold TV.
B Press MBR SET.
C Press the Number keys to enter your TV’s brand code.
D Press OK, and release TV. The TV should turn off.
NOTES:
C Operate TV
When the channel is changed on the VCR;
● The “STEREO” indication appears on the screen for about
5 seconds if the program is a stereo broadcast.
● The “SAP” indication appears on the screen for about 5 seconds
if the program is a SAP broadcast.
While holding down TV, press one of the following buttons:
POWER, TV/VCR, TV CH+/–, ^ (TV Muting), TV VOL+/–, and
the Number keys.
● For some brands, you must press ENTER after having pressed the
Number keys to enter a channel number.
● Both indications appear when a stereo program is accompanied
by SAP sound.
TV BRAND
CODE
TV BRAND
CODE
JVC
01, 03
10
SONY
07
12
13
13
08
09
HITACHI
MAGNAVOX
MITSUBISHI
PANASONIC
RCA
SAMSUNG
SANYO
SEARS
Ⅵ AUDIO MONITOR — HI-FI/HI-FI L/HI-FI R/NORM/MIX
This VCR can record two sound tracks simultaneously (normal
and Hi-Fi) on a Hi-Fi stereo tape. You can select the sound track(s)
to listen to while playing back a Hi-Fi stereo tape. In addition,
when playing back a prerecorded tape containing two separate
audio programs on the Hi-Fi tracks, you can choose either one by
selecting either “HI-FI L” or “HI-FI R”.
HI-FI: Normally select this. Hi-Fi sound is played back.
HI-FI L: Sound on the left Hi-Fi channel is played back.
HI-FI R: Sound on the right Hi-Fi channel is played back.
NORM: Sound on the normal track is played back.
02
03
04, 11
05
TOSHIBA
ZENITH
SHARP
06
Cable Box or DBS Receiver Brand Setting
A Turn on cable box or DBS receiver
Turn on the cable box or DBS receiver using the Power button on
the unit or its Remote.
MIX: Both sounds on the Hi-Fi track and normal track are mixed
and played back.
B Enter brand code
A Press and hold CABLE/DBS.
B Press MBR SET.
C Press the Number keys to enter your cable box’s (or DBS
receiver’s) brand code.
D Press OK, and release CABLE/DBS.
NOTES:
● While playing back a monaural tape, sounds on the normal
track will be heard regardless of this setting.
● If RF connection is used for viewing pictures on the TV, sound
will be monaural even though you select “HI-FI”.
● You can also use the A. MONITOR button on the Remote to
select the desired monitor sound.
C Operate cable box or DBS receiver
While holding down CABLE/DBS, press one of the following
buttons: POWER, TV CH+/–, and the Number keys.
● For some brands, you must press ENTER after having pressed the
Number keys to enter a channel number.
● To change the cable box’s (or DBS receiver’s) channels, press TV
CH+/– or the Number keys. (The CH+/– button can be used to
change the VCR’s channels only.)
– Other Functions –
CABLE BOX BRAND
CODE
Changing Remote Control Code
ARCHER
01, 05, 17
This Remote is capable of transmitting two control codes; one set
to respond to A code control signals and another set to respond to
B code control signals. This Remote control is preset to send A
code signals because your VCR is initially set to respond to A
code signals. You can easily modify your VCR and the Remote to
respond to B code signals. When using two JVC VCRs, set two
VCRs and their Remotes to different codes, so that you can
operate these VCRs separately.
CABLETENNA
CABLEVIEW
CITIZEN
01, 17
15, 16, 17, 21, 25
15, 16, 17, 21, 25
CURTIS
02
DIAMOND
EASTERN
01, 17
19
GC BRAND
GEMINI
15, 16, 17, 21, 25
15
GENERAL INSTRUMENTS
HAMLIN
01, 04, 06, 11, 12, 15, 28
10, 18, 19, 23
A Set remote control code for Remote
JASCO
15
A Press and hold A/B.
JERROLD
01, 04, 06, 11, 12, 15, 28
NOVAVISION
OAK
02
B Press the Number key “2”.
07
C Press OK, and release A/B.
PANASONIC
PULSER
13, 14
● The Remote now can transmit B code control signals.
15, 16, 17, 21, 25
13, 14
RCA
REGAL
B Check remote control code for VCR
Press and hold 4 on the VCR for more than 5 seconds while the
VCR is turned off. The code currently set appears on the display
panel.
10, 18, 19, 23
19
REGENCY
REMBRANDT
SAMSUNG
SCIENTIFIC ATLANTA
SIGMA
01, 16, 17
05, 16, 24
02
C Change code for VCR
Press any key on the Remote. The VCR now responds to B code
control signals.
● To set the Remote and the VCR back to A code control signals,
repeat the same procedure as shown above except pressing the
Number key “1” in step B of 1.
07
SL MARX
05, 16, 17, 24, 25
13, 14
SPRUCER
STARGATE
TELEVIEW
TOCOM
05, 15, 16, 17, 21, 24, 25
05, 16, 24
01, 04, 16
01, 17
UNIKA
UNIVERSAL
VIDEOWAY
ZENITH
16, 17, 25
03, 09, 22
03, 09, 22
To control two VCRs with the same Remote
You can control two JVC VCRs by switching the remote control
code for the Remote between A and B (੬ step A), keeping two
VCRs to different control codes.
DBS RECEIVER BRAND
CODE
JVC (DISH Network)
ECHOSTAR (DISH Network)
PRIMESTAR
51
51
50
41
40
● To change only the remote control code for the Remote, DO
NOT perform steps B and C.
SONY (DSS)
RCA (DSS)
Editing
Specifications
You can use your VCR as the playback or recording VCR. You can
use a camcorder as the playback VCR and your VCR as the
recording VCR. Refer also to the other components’ instruction
manuals for connection and its operations.
GENERAL
Power requirement
Power consumption
Power on
: AC 120 Vd, 60 Hz
A Make connections
Example: When using this VCR as the playback VCR
: 18 W
: 2.0 W
Power off
Temperature
Operating
Storage
Operating position
: 5°C to 40°C (41°F to 104°F)
: –20°C to 60°C (–4°F to140°F)
: Horizontal only
This VCR (for playback)
To AUDIO/VIDEO OUT
Dimensions (W x H x D) : 360 mm x 94 mm x 247 mm
(14-3/16" x 3-3/4" x 9-3/4")
Weight
: 3.0 kg (6.6 lbs)
Format
: VHS NTSC standard
Maximum recording time
Audio/video cable
(not supplied)
SP
EP
: 210 min. with ST-210 video cassette
: 630 min. with ST-210 video cassette
VIDEO/AUDIO
Signal system
:
NTSC-type color signal and EIA
monochrome signal, 525 lines/
60 fields
To audio/video input
Recording/Playback
system
Signal-to-noise ratio
Horizontal resolution
Frequency range
Normal audio
:
DA-4 (Double Azimuth) head helical
scan system
45 dB
Another VCR (for recording)
:
:
230 lines
● When using this VCR as the recording VCR, connect this VCR’s
audio/video input connectors to the audio/video output
connectors on the other VCR. If the playback VCR is monaural,
connect the audio output connector on the playback VCR to the
left audio input connector on this VCR.
:
:
:
70 Hz to 10,000 Hz
20 Hz to 20,000 Hz
RCA connectors (IN x 1, OUT x 1)
Hi-Fi audio
Input/Output
B Load cassettes
TUNER
Insert the playback cassette into the playback VCR and the
cassette to be recorded on into the recording VCR.
Tuning system
Channel coverage
VHF
: Frequency-synthesized tuner
C Select input mode on recording VCR
: Channels 2–13
: Channels 14–69
: 113 Channels
: Channel 3 or 4 (switchable; preset to
Channel 3 when shipped) 75 ohms,
unbalanced
Select the correct external input on the recording VCR.
On this VCR (when using this VCR as the recording VCR);
Select “F-1” — when connecting the other VCR to the audio/video
input connectors on the front panel.
Press AUX or CH+/– on the Remote. You can select the input
mode also by pressing PAUSE[CH], and then FF[CH+] or
REW[CH–] on the VCR. See step B in “Basic Recording”.
UHF
CATV
RF output
TIMER
D Select edit mode
Clock reference
Program capacity
:
:
Quartz
Set the edit mode to “ON” for the VCRs if such a mode is
equipped.
1-year programmable timer/
8 programs
● On this VCR, set “PICTURE CONTROL” to “EDIT”.
Memory backup for timer is not supported.
E Start playback
Press PLAY (4) on the playback VCR.
ACCESSORIES
F Start recording
Press REC (7) on the recording VCR.
Provided accessories
: RF cable (F-type),
Infrared remote control unit,
“AA” battery x 2
Specifications shown are for SP mode unless specified otherwise.
E. & O.E. Design and specifications subject to change without
notice.
FOR SERVICING (Only in U.S.A.)
HOW TO LOCATE YOUR JVC SERVICE CENTER
TOLL FREE: 1-800-537-5722
Dear Customer,
In order to receive the most satisfaction from your purchase, please read the instruction booklet before operating the
unit. In the event that repair is necessary, or for the address nearest your location within the Continental United States,
retain your Bill of Sale for Warranty Service.
— JVC
JVC SERVICE & ENGINEERING
COMPANY OF AMERICA
DIVISION OF JVC AMERICAS CORP.
Sophisticated electronic products may require occasional service. Just as quality is a keyword in the engineering and
production of the wide array of JVC products, service is the key to maintaining the high level performance for which JVC
is world famous. The JVC service and engineering organization stands behind our products.
NATIONAL HEADQUARTERS
JVC SERVICE & ENGINEERING COMPANY OF AMERICA
DIVISION OF JVC AMERICAS CORP.
10 New Maple Avenue
Pine Brook, NJ 07058-9641
ACCESSORIES
Don’t service the product yourself.
To purchase accessories for your JVC product, you
may contact your local JVC Dealer.
From the 48 Continental United States call toll free:
CAUTION
To prevent electrical shock, do not open the cabinet.
There are no user serviceable parts inside.
Please refer to qualified service personnel for repairs.
WARRANTY (Only in U.S.A.)
LIMITED WARRANTY
CONSUMER VIDEO 1-90
JVC COMPANY OF AMERICA warrants this product and all parts thereof, except as set forth below ONLY TO THE ORIGINAL
PURCHASER AT RETAIL to be FREE FROM DEFECTIVE MATERIALS AND WORKMANSHIP from the date of original retail
purchase for the period as shown below. (“The Warranty Period”)
THIS LIMITED WARRANTY IS VALID ONLY IN THE FIFTY (50) UNITED STATES, THE DISTRICT OF COLUMBIA AND IN
COMMONWEALTH OF PUERTO RICO.
WHAT WE WILL DO:
If this product is found to be defective, JVC will repair or replace defective parts at no charge to the original owner. Such repair and
replacement services shall be rendered by JVC during normal business hours at JVC authorized service centers. Parts used for
replacement are warranted only for the remainder of the Warranty Period. All products and parts thereof may be brought to a JVC
authorized service center on a carry-in basis except for Television sets having a screen size 25 inches and above which are covered
on an in-home basis.
WHAT YOU MUST DO FOR WARRANTY SERVICE:
Return your product to a JVC authorized service center with a copy of your bill of sale. For your nearest JVC authorized service
center, please call toll free: (800) 537-5722.
If service is not available locally, box the product carefully, preferably in the original carton, and ship, insured, with a copy of your bill of
sale plus a letter of explanation of the problem to the nearest JVC Factory Service Center, the name and location of which will be
given to you by the toll-free number.
If you have any questions concerning your JVC Product, please contact our Customer Relations Department.
WHAT IS NOT COVERED:
This limited warranty provided by JVC does not cover:
1. Products which have been subject to abuse, accident, alteration, modification, tampering, negligence, misuse, faulty installation,
lack of reasonable care, or if repaired or serviced by anyone other than a service facility authorized by JVC to render such service,
or if affixed to any attachment not provided with the products, or if the model or serial number has been altered, tampered with,
defaced or removed;
2. Initial installation and installation and removal for repair;
3. Operational adjustments covered in the Owner’s Manual, normal maintenance, video and audio head cleaning;
4. Damage that occurs in shipment, due to act of God, and cosmetic damage;
5. Signal reception problems and failures due to line power surge;
6. Video Pick-up Tubes/CCD Image Sensor, Cartridge, Stylus (Needle) are covered for 90 days from the date of purchase;
7. Accessories;
8. Batteries (except that Rechargeable Batteries are covered for 90 days from the date of purchase);
There are no other express warranties except as listed above.
THE DURATION OF ANY IMPLIED WARRANTIES INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY, IS LIMITED
TO THE DURATION OF THE EXPRESS WARRANTY HEREIN.
JVC SHALL NOT BE LIABLE FOR THE LOSS OF USE OF THE PRODUCT, INCONVENIENCE, LOSS OR ANY OTHER
DAMAGES, WHETHER DIRECT, INCIDENTAL OR CONSEQUENTIAL (INCLUDING, WITHOUT LIMITATION, DAMAGE TO TAPES,
RECORDS OR DISCS) RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING OUT OF ANY BREACH OF THIS
WARRANTY. ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR PARTICULAR PURPOSE, ARE LIMITED TO THE WARRANTY PERIOD SET FORTH ABOVE.
Some states do not allow the exclusion of incidental or consequential damages or limitations on how long an implied warranty lasts,
so these limitations or exclusions may not apply to you. This warranty gives you specific legal rights and you may also have other
rights which vary from state to state.
JVC COMPANY OF AMERICA
DIVISION OF JVC AMERICAS CORP.
1700 Valley Road
Wayne, New Jersey 07470
REFURBISHED PRODUCTS CARRY A SEPARATE WARRANTY, THIS WARRANTY DOES NOT APPLY. FOR DETAILS OF
REFURBISHED PRODUCT WARRANTY, PLEASE REFER TO THE REFURBISHED PRODUCT WARRANTY INFORMATION
PACKAGED WITH EACH REFURBISHED PRODUCT.
For customer use:
Enter below the Model No. and Serial No. which is located either on the rear, bottom or side of the cabinet. Retain this information
for future reference.
Model No.:
Serial No.:
Purchase date:
Name of dealer:
|