NON-BT
IMPORTANT
READ THIS FIRST
TM
JABRA FreeSpeak QUICK START GUIDE
For Nextel Phones
Model #:100-91030000-02
Model #:100-91130000-02
Model #:100-91430000-02
Headset Indicator Light
(Blue LED)
Multi-Function Button
MiniGel™
Volume Control Button
BEFORE USING YOUR HEADSET
Charge FreeSpeak – FreeSpeak is rechargeable and must be charged before use.
1. Insert the headset fully into its multi-adapter.
2. Plug one end of the AC power adapter into the multi-adapter and the other end into an
electrical wall outlet.
3. Charge your headset for approximately 2 hours or until both blue indicator lights go out.
Important: Blue indicator lights on the headset and multi-adapter will both be on while
charging and will turn off when charging is complete.
Connect multi-adapter to phone
• For phones with standard 2.5mm headset jacks: Plug the multi-adapter’s connector into the
2.5mm headset jack on your phone.
Location of phone’s headset
jack may vary.
• For i2000plus, i2000, i1000plus, i1000, r750plus, i700plus, i550plus, i500plus and i500
phones: Plug the audio adapter (sold separately) into your phone. Then plug the multi-
adapter’s connector into the audio adapter.
To answer and end calls with only the headset:
Some phones enable you to answer or end a call by pressing and releasing
without having
to touch the phone. For all Nextel phone models (except the i1000), the phone’s Automatic
Answer feature needs to be activated for this headset feature to work.
For the BlackBerry 6510, FreeSpeak's Anwer/End feature has to be turned on.
To turn on FreeSpeak's Answer/End feature:
1) Ensure that the AC power adapter is not connected.
2) Put the headset in the multi-adapter.
3) Use the stylus to press the stylus switch for about 12 seconds.
4) You will then see a number of blinks (long flashes) on the multi-adapter indicator
light which tell you whether this feature is enabled or disabled according to the
following table:
Answer/End Feature
Comments
Number of Blinks
4
5
Enabled
Disabled
--
Default Setting
5) Repeat steps 1-4 to switch between enabled and disabled settings.
If you are enabling Answer/End feature for the first time, you should test answering and ending
calls to ensure that your phone supports this feature.
For more information, see “Enhanced Features” at www.jabra.com/fscs.
Calls can be ended by the headset only by waiting for the line to disconnect.
STATUS INDICATORS
What you see
What you hear
Status
Flashes every second
When Active Mode
starts: quick series
Active Mode
• Call in progress
of TWO tones – low • Up to 4 hours of talk time
to high pitch
When Standby
Mode starts: quick
series of TWO
tones – high to low
pitch
Standby Mode
• Waiting for call
• Up to 100 hours of standby time with
mheadset in multi-adapter
Flashes every 3
seconds
TIPS & SOLUTIONS
To prolong battery life:
• After you’ve ended a call using your phone’s keypad, always remember to place the
headset in Standby mode by pressing and releasing
when not in use.
• Dock the headset firmly in its multi-adapter when not in use.
If you press and release
and the headset stays in Standby mode:
If FreeSpeak becomes unpaired, it will not respond to the
occur when you first receive the product or when you hold the
the product.
button. In rare cases, this may
button too long while using
To “pair” the headset with the multi-adapter:
1. Ensure headset is off.
2. Press
until you see a solid blue light on the headset, then release.
3. Use the stylus to press down on the
stylus switch until you see a solid blue
light on the multi-adapter, then
release.
Multi-adapter
Important: Once pairing is complete,
lights on both the headset and multi-
adapter will begin flashing (Standby
mode).
Stylus
Switch
Stylus
If you hear an echo of your voice – You may need to adjust
microphone levels.
To reduce the echo:
Flashes or
Beeps
Microphone Level
High (default)
Medium
1
1. Lower the volume of your phone and headset.
2. If echo persists, put FreeSpeak in Active mode.
2
3
Low
3. Use the stylus to press down on the stylus switch (as shown above) until you see a solid
c blue light on the multi-adapter. Continue to press down until you see/hear 1, 2, or 3
z flashes/beeps, then release. The last number of flashes/beeps corresponds to the final
c setting.
4. Repeat step 3 to cycle between different microphone levels.
If the headset is not responding or the light will not turn off after pairing - You may need to
reset your headset.
1. Plug one end of the AC power adapter into the multi-adapter and the other end into an
electrical wall outlet.
2. Insert the headset into the multi-adapter for about 3 seconds, then remove.
To improve audio clarity:
Stay within 30 feet (10 meters) of your multi-adapter. In general, you will get the best perform-
ance when there are no obstructions (including parts of the body) between your headset and the
multi-adapter.
Need more help?
1. Consult the complete User’s Guide
2. Web: www.jabra.com/fscs (for the latest support info)
3. Telephone: (858) 622-9955, Monday to Friday 8am to 5pm PST
(800) EAR-2230 (USA and Canada)
|