|
TV 24769
Futura™ Outdoor TV Antenna
Thank you for your purchase of the GE branded Futura™ Outdoor TV Antenna. Before
you begin your installation, please read these instructions carefully and keep these
instructions for future reference.
INTRODUCTION
The 24746 Futura™ Outdoor TV Antenna is specially designed for digital terrestrial
broadcasting reception. The compact and stylish housing can be placed in low visibility
locations.
Features:
• Compact and Stylish Design
• Digital HDTV Ready
Package Content:
• Futura™ Outdoor Antenna
• Adjustable Wall Mount Bracket
• Instruction Manual
Product Description:
1
d. Mount the Futura™ Outdoor Antenna to the wall bracket. (Be sure to
insert the stem completely into the socket located on the bottom of the
antenna)
2. Locate the desired entry for the cable.
a. Check to make sure there are no electrical wires where the hole will be
drilled.
b. Check to make sure that there is not a stud in the location were the hole is
to be drilled.
c. Once you have checked the location for wires and stud, drill your hole
using the 5/16” drill bit all the way through until the drill bit comes
through the inside wall.
d. Take the feed through bushing (AV23257) and place a small amount of
caulk on the inside flange of the feed through bushing
e. Press the feed through busing into the hole until it is flush with the wall
3. Measure the amount of coax cable needed for the installation and preparing the
cable for installation.
a. Start at the antenna and measure the exact route the cable will be ran to the
hole drilled in the wall. Add about 3’ to 4’ extra to the measurement for
slack in connecting the cable to the antenna and for stripping the cable and
running it through the wall.
b. Using the cable stripper (AV23318), strip the cable as instructed on the
cable stripper packaging
c. Attach the RG6 weather proof “F” connector to the cable (AV23260)
d. Using the “F” Connector Crimp Tool (AV23258), crimp the “F” connector
as instructed
e. Attach the finished end to the antenna
f. Using the nail in cable clips (AV23251), secure the cable to the exterior
wall placing a clip approx 6’ apart keeping the cable taught as it is being
fasten to the wall.
g. Take the unfinished end of the coax cable near the hole drilled and feed it
into the feed through bushing until the cable comes out on the other side.
h. Cut off excess cable; be sure to leave about 12” of cable to work with.
i. Strip the end of the cable as you did on the other end and attach the RG6
“F” connector and crimp as done previously.
j. Attach the finished end to the coax wall plate (AV23235 or 23239). Push
the extra cable back into the wall
k. Make sure the wall plate rest flush against the wall and mark the holes to
be drilled for mounting the wall plate. (One hole at top and one hole at the
bottom)
l. Using the 3/16” drill bit drill the two holes marked for the coax wall plate.
Stop drilling when the drill bit drills through the sheet rock (approx. ½”
deep)
m. Insert the wall anchors and tap in until flush with the wall
n. Position the coax wall plate until the holes line up the wall anchors and
use the screws provided with the wall plate to fasten the wall plate to the
wall.
3
o. Using a ready made coax cable, attach cable to the newly installed wall
plate and the other end to the TV
How to use your new Futura™ Antenna:
1. Turn TV on
2. Set the TV to the lowest VHF channel
3. If picture is not clear, try one or all of the following suggestions:
a. Turn the antenna
b. Make sure the cable connections are good and tight
c. Make sure you do not have any devices near the TV or the location of the
Antenna that may cause interference. If you do move the device if
possible.
Factors that can cause interference with reception:
• Air Conditioners
• Hair Dryer
• Microwave Oven
• Cordless Phones
• Environmental surroundings
• Space Heaters
• High power consumption devices
• Weather Condition
• Type of structure (Brick or Stone, or older homes with plastered walls)
4
|