98505
Wireless Optical
Presentation Mouse
Instruction Manual
For technical support contact Jasco Products at 1-800-654-8483 or
Battery Installation
1. Press the battery release button on top of the mouse.
2. The battery door will open.
3. Insert 1 AA battery, being sure to match the polarity
of the battery with the polarity markings inside the
battery compartment.
4. Close the battery door.
Mouse Installation
1. Slide the USB Receiver out of the bottom of the mouse.
2. Once the receiver has been removed, the Battery Meter
will light up.
LED
Green Light = battery life is good.
Red Light (Blinking slowly) = battery is low.
Red Light (Blinking rapidly) = change battery.
3. Insert the USB receiver into an available USB port.
The receiver has an LED on the top.
Green Light on Receiver = Mouse movement.
Red Light on Receiver = Low battery.
4. Please refer to page 6 of this manual for the
Mouse Suite Installation.
Battery Light
3
Reconnecting the Mouse to the Receiver
This mouse will usually automatically connect to the receiver. If needed,
you can connect the mouse to the receiver by following these steps.
1. Press the button on top of the receiver. The LED will light up on
the receiver.
2. Press the button on the bottom of the mouse. It is located where the
receiver is stored.
3. The LED on the receiver will blink and you are finished.
Storing the Receiver
To help conserve battery and increase portability you
may store the receiver under the mouse. To do this,
simply unplug the receiver from your USB slot and
place it in the designed position on the bottom of the
mouse. Once the receiver is correctly in place, the power
will automatically shut off.
Using the Laptop Clip
Your mouse is equipped with the Laptop Clip. This is used for easy storage
of the mouse while on the go with your laptop. To use this clip, simply insert
the clip on the bottom of the mouse then place your mouse into the modem
slot on your laptop. Please ensure that your modem slot is not in use before
attaching the storage clip.
4
Presentation Mode
To switch your mouse to
Presentation Mode please
slide the switch on the bottom
of the mouse towards the
presentation icon.
Presentation Mode Functions
Your mouse is equipped with a variety of functions to help assist you with
any presentation. Please refer to the diagram above for a short description
of the button functions.
!CAUTION!
Do not aim or look into the integrated laser pointer. Direct exposure to
laser will cause damage to the eye.
5
Mouse Suite Software (for Windows® Vista, XP & 2000 only)
The Mouse Suite is a software program with many features that give
amazing functionality to your GE mouse. Here is a brief overview.
Installation Procedure
1. Insert the Installation CD into the computer CD drive.
2. Run the file named “Setup”.
3. Follow the instructions on the screen.
4. Click Finish when completed.
Buttons Tab
From this screen you can set the function of each button on your mouse.
There are over 33 functions to choose from. To specify the function of each
button follow these steps:
6
1. Select the button you
want from the Button
drop down menu.
2. Next select the function
you want by using the
Function drop down menu.
3. After you have selected
the features you want
click apply at the bottom
of your screen. You may
change these features at
any time.
You may also check your battery life from this screen. The battery indicator
is located on the right side of the window.
Magnifier Function
This feature allows you to
use the scroll button as a
magnifier.
To enable this feature,
simply check the box labeled
“Magnifier” and click Apply.
Press the middle scroll button
to activate the magnifier.
To make the magnifier size
taller, press and hold the
scroll button again and move
the mouse up or down. To make the magnifier size wider, move the mouse
right or left.
7
Double-Click Tab
This screen allows you to
set the double-click speed
of your mouse. Use the
slider to set the desired
speed. You must click Apply
to update any changes.
Orientation Tab
This feature allows you to
set the orientation of the
mouse while finding the
most comfortable position
to hold the mouse. Please
follow the directions on the
screen to set the orientation.
8
Wheel Tab
This screen allows you to
select different wheel
operations. You may also
select vertical scrolling
speed as well as horizontal
scrolling speed. If you would
like to reverse the scrolling
direction of the mouse,
please check the box
labeled Reverse Scrolling
Direction.
Pointer Utility Tab
From this screen you can
select different functions
for the pointer.
Pointer Wrap
The pointer wrap feature
allows the pointer to go in
one side of the screen and
come out of the opposite
side. This works at both
sides of the screen as well
as top and bottom. This allows easier and more functional mouse
navigation with less wrist and arm movement.
9
Slow Motion
This feature allows the pointer to move in slow motion by pressing the Shift
key. This will help the precision of the pointer.
X-Focus
This feature allows you to make an inactive window active by simply moving
the pointer over the title bar.
Troubleshooting
• Mouse does not work properly
- Check the battery life on your mouse. If it is low please install new batteries.
- Reconnect your mouse to the receiver. Press the link button on the receiver.
Press the link button on the bottom of your mouse. (page 4)
• Mouse does not move on screen.
- Reconnect your mouse to the receiver.
- Change the batteries on your mouse.
- Make sure that your USB receiver is completely plugged into the
computer’s USB port.
Questions? Please call 1-800-654-8483 (option #4)
Monday—Friday, 9:00 am—5:00 pm CST.
10
Five Year Limited Warranty
Jasco Products Company warrants this product to be free from
manufacturing defects for a period of five years from the original date of
consumer purchase. This warranty is limited to the repair or replacement
of this product only and does not extend to consequential or incidental
damage to other products that may be used with this unit. This warranty is
in lieu of all other warranties express or implied. Some states do not allow
limitations on how long an implied warranty lasts or permit the exclusion or
limitation of incidental or consequential damages, so the above limitations
may not apply to you. This warranty gives you specific rights, and you may
also have other rights which vary from state to state. If unit should prove
defective within the warranty period, return prepaid with dated proof of
purchase to:
Jasco Products Company
10 East Memorial Dr
Oklahoma City, OK 73114
FCC Statement
Notice: Federal Communications Commission (FCC) requirements, Part 15
This equipment has been tested and found to comply with the limits for a
class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
11
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
CAUTION: Any changes of modifications not expressly approved by
the grantee of this device could void the users authority to operate the
equipment. This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
FDA Notice
This product complies with DHHS Rules 21CFR Chapter I, Sub chapter J.
This product has been designed and manufactured according to IEC60825-1
on the safety label of laser product.
CLASS 2 LASER
Class 2 Laser Product
It is recommended not to point directly in the eye or any other optical device.
Distributed for GE
by Jasco Products Company
311 N.W. 122nd Street, Oklahoma City, OK 73114
12
|