45233
Home Monitoring
Wireless Color
Camera
User Manual
For indoor/outdoor use. Do not use in wet locations.
1-800-654-8483
3
2. Wall mounting hardware
3. AC adapter
CHOOSING A CAMERA MOUNTING LOCATION
The 45233 Wireless Color Camera can be positioned
on a desktop, or mounted to a wall. It is suitable for
indoor or outdoor use. When choosing a mounting
location, please be advised:
• Do not use in wet locations. If using outside,
position camera in a sheltered location.
• DO NOT position the camera so that it points
directly into the sun or any bright light, as this
may cause damage to the camera.
• Avoid viewing areas where half the area is in
bright sunlight and the other half is dark, such
as in the shadow of a building. All types of
cameras have difficulty “seeing” into areas of
such divergent light levels.
• In low light conditions, the camera will
automatically activate the Infrared (IR) LED’s and
switch the camera to Night Vision mode. Night
Vision viewing distance is up to 10 feet.
• If using the included AC adapter to power the
camera, it must be positioned no farther than
8’ from an AC outlet. Do not use the supplied
4
adapter outside or run the cord through walls.
If you need to extend the AC adapter cable,
15 ft. extensions are available by contacting
Customer Service at 800-654-8483. If using
the optional rechargeable NiMH battery (sold
separately), the operational time is up to 5
hours, depending on usage.
• The Camera has an unobstructed wireless
transmission range up to 200 ft. from the
receiver. Transmission distance indoors is
reduced due to interior walls, wiring, household
fixtures and metal plumbing.
NIGHT VISION
Infra-Red
(IR) LEDs
The 45233 Wireless Color
Camera features Night
Vision technology. Objects
and images can be seen in
little or no light up to 10 ft.
The camera uses a special
image sensor that
Sensor
automatically detects
available light levels.
It turns on/off the Infra-Red (IR)
LEDs on the front of the camera. These LEDs provide
artificial light that allows the camera to ‘see’ in the
dark. Night Vision will appear as a Black and White
image. When the image sensor detects enough
5
light, color will return to the images.
MULTI-CAMERA SYSTEMS
The 45233 Wireless Color Camera is designed as an
add-on camera to work with the following GE Color
and B/W Wireless camera systems - 45234, 45235,
45236. These systems can accept a maximum of
two cameras.
Channel Selection
Each wireless camera must be assigned to a
specific channel (1 or 2) through the use of a slide
switch located on the underside of the camera
housing. The receiver or monitor must have its
channel selection set to the same corresponding
number.
In a two camera system, one camera is set to
Channel 1 and the other is set to Channel 2.
Channel
Selection
switch
6
The receiver or monitor must be set to the 1/2
position in order to view both cameras alternately
(see receiver or monitor manuals for specific
channel selection requirements).
MAX
INSTALLATION
Desktop Mount:
1. Place camera in desired
location on a flat surface.
MIN
2. Set Channel switch on
camera to 1 or 2. Set receiver or
monitor to same channel.
3. Adjust antenna and camera
angle as needed for the clearest
picture.
Antenna pivots to
increase/decrease
signal strength
Wall Mount:
1. To simplify the wall mount process, you will
find a custom mounting plate included with the
mounting hardware.
2. Select the ideal location. Using the supplied wall
mount as a template, drill two 3/16” holes in the
desired mounting location, and install the two wall
anchors (included) into the holes, or screw directly
into a wall stud. Secure the mounting plate to the
wall. Do not run the adapter cable in walls; when
securing the cable, do not cut or puncture.
7
3. Set Channel
switch on camera
to 1 or 2. Slide the
camera onto the
locking pins of the
mounting plate.
4. Adjust antenna
and camera angle
as needed for the clearest picture.
OPTIONAL WIRELESS BATTERY PACK AVAILABLE
(SOLD SEPARATELY)
Rechargeable NiMH Battery is available for use
with the 45233 Wireless Color Camera. This
850mAh battery will power the 45233 Camera for
approximately 5 hours on a single charge. To order
call our Customer Support department at 1-800-
654-8483, Monday–Friday 8 a.m.–5 p.m. CST.
AC adapter
charges the
battery
Wall or desktop mount
8
TROUBLE SHOOTING
If you are having trouble operating this product,
please consult the guide below. If you have any
questions or feel the camera system is not
operating correctly, or you simply need additional
information, please visit our web site
Customer Service Group 1-800-654-8483.
SYMPTOM
No camera picture
1. Check all connectors. Make sure camera(s) and
receiver are powered ON.
2. Ensure camera(s) and receiver are set to correct
channel(s).
3. Make sure camera is within range of receiver.
4. Adjust the antenna for the camera, monitor or
both to obtain best image.
Blank monitor
1. Make sure receiver or monitor is switched ON,
and the correct video input has been selected
2. If using AC adapter, make sure it is plugged in.
3. If using a battery, make sure it is installed
correctly, and ensure it is fully charged.
9
Interference on camera picture
1. Make sure each camera (transmitter) is within
range, and that no large obstructions are blocking
the signal.
2. Try repositioning the camera, monitor (receiver) or
both to improve the reception quality.
3. If a camera is positioned close to the monitor,
point antenna away from the receiver.
4. Reposition other nearby equipment transmitting
on the 900MHz frequency.
5. Adjust the antenna for the camera, monitor or
both to obtain best image.
Audio problems
1. Ensure the volume is turned up sufficiently on the
Monitor (or TV).
2. Make sure the sound is within the microphone
range.
3. If the unit emits a loud wailing sound (feeds back),
try moving the camera away from the receiver or
angle the receiver differently.
CAMERA SPECIFICATIONS (Subject to change without notice.)
TV System............................................................................................NTSC
Integrated Lens........................................5.6mm, F1.8 fixed focus
Resolution................................................... 360 horizontal TV Lines
10
High-Speed Electronic Shutter.................1/60 - 1/15,000 sec
Image Sensor........................................................................1/3” CMOS
Min. Illumination..................0 lux up to 3 ft, 0.5 lux up to 10 ft
Voltage................................................................................................. 9VDC
Current Consumption.......................................................80~150mA
Overall Size...................................................2.35”W x2.74Hx3.160D
Frequency Range........................................................902 - 928 MHz
Modulation..............................................................................................FM
Channel Selection......................................................................Manual
Case Finish.................................................UV resistant ABS plastic
WARRANTY
ONE-YEAR LIMITED WARRANTY: Jasco Products Company
warrants this product to be free from manufacturing defects
for a period of one year from the original date of consumer
purchase. This warranty is limited to the repair or replacement
of this product only and does not extend to consequential or
incidental damage to other products that may be used with
this unit. This warranty is in lieu of all other warranties express
or implied. Some states do not allow limitations on how long an
implied warranty lasts or permit the exclusion or limitation of
incidental or consequential damages, so the above limitations
may not apply to you. This warranty gives you specific rights,
and you may also have other rights which vary from state to
state. If unit should prove defective within the warranty period,
return prepaid with dated proof of purchase to:
Jasco Products Company
10 E. Memorial Road, Oklahoma City, OK 73114
11
WARNING
Risk of fire and shock
• Only use the supplied cUL listed AC to DC adapter.
• The supplied adapter is for indoor use only.
• Do not run the camera cable inside walls; when securing the
cable, do not cut or puncture
• Do not use in wet locations
FCC STATEMENT
NOTE: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician
for help.
12
Made in China
is a trademark of General Electric Company
and is used under license to Jasco Products Company LLC,
10 E. Memorial Road, Oklahoma City, OK 73114
|