AV93299
Video Converter
(RF Modulator)
INSTRUCTION MANUAL
Please read before using this equipment.
NOTETO CATV SYSTEM INSTALLER:
INTRODUCTION
This reminder is provided to call the CATV system installer’s
attention to Article 820-40 of the NEC that provides guidelines for
proper grounding and, in particular, specifies that the cable
ground shall be connected to the grounding system of the build-
ing, as close to the point of cable entry as practical.
Your Video Converter (RF Modulator) is designed to convert
the separate audio and video signals (from a DVD, video
camera, or video game, for example) into VHF TV signals
that you can view on aTV set equipped with only a 75 Ohm
(F-type) input.
WARNING:To prevent fire or shock hazard, do not expose this
product to rain or moisture.This unit for indoor use only
The FCC WantsYou to Know
This device complies with Part 15 of FCC Rules. Operation is
subject to the following two conditions: (1)This device may
not cause harmful interference, and (2) this device must
accept any interference received, including interference that
may cause undesired operation.
CAUTION
RISK OF ELECTRIC SHOCK.
!
DO NOT OPEN
CAUTION:TO REDUCETHE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER OR BACK. NO USER-
SERVICE-ABLE PARTS INSIDE. REFER SERVICING
TO QUALIFIED PERSONNEL.
Your modulator might causeTV or radio interference even
when is operating properly.To determine whether your mod-
ulator is causing the interference, turn it off. If the interfer-
ence goes away, your modulator is causing it.
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated “dangerous voltage” within
the product’s enclosure that may be of sufficient mag-
nitude to constitute a risk of electric shock to persons.
Try to eliminate the interference by:
•
•
moving your RF Modulator away from the receiver
connecting your RF Modulator to an outlet that is on a
different electrical circuit from the receiver
contacting your lcoal store for help
•
The exclamation point with an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in
If you cannot eliminate the interference, the FCC requires
that you stop using your RF Modulator. Changes or modifi-
cations not expressly approved by the party responsible for
compliance could void the user’s FCC authorization to oper-
ate this equipment.
!
the literature accompanying the appliance.
Notice :The changes or modifications not expressly approved by
the party responsible for compliance could void the user‘s
authority to operate the equipment.
2
3
REQUIRED PARTS
The following items (not supplied) are required to connect
your RF Modulator to a video input source and yourTV.
CONNECTIONS
Follow these steps to connect your RF Modulator.
1. If your video source is stereo, plug the connectors on
one end of a stereo A/V cable into the video and audio
input jacks on the RF Modulator. Plug the connectors
on the cable’s other end into to video and audio output
jacks on the video source, using the color coding on
•
one audio/video shielded cable with three phono
connectors at each end, if the video source’s audio
output is stereo; or one audio/video shielded cable
with two phono connectors at each end if the video
source’s audio output is monaural
two 75-ohm coaxial cables with F-type connectors
a 75-ohm-to-300-ohm matching transformer, if yourTV
does not have a VHF 75-ohm F-connector
the connectors as a guide.
Video Source
•
•
(DVD Player)
Note:The audio signal will be modulated to mono,
whether the video source is stereo or monaural.
If your video source is monaural, plug the connectors on
one end of an A/V cable into the video and audio input
jacks on the RF Modulator (using the AUDIO L jack). Plug
the cable’s other ends into the video and audio jacks on
the video source. Connect the 75-ohm coaxial cables to
the RF Modulator following these guidelines:
Video Source
(DVD Player)
Note to the CATV System Installer:This reminder is
provided to call the CATV system installer’s attention to
article 820-22 of the NEC that provides guidelines for
proper grounding and, in particular, specifies that the
cable ground shall be connected to the grounding system
of the building, as close to the point of cable entry as
practical.
4
5
If yourTV is already connected to another VHF input
source (such as cable, an antenna, or a VCR, for
example), disconnect the VHF input source’s 75-ohm
cable from theTV’s 75-ohme VHF/UHF terminal, and
reconnect it to the RF Modulator’s ANT IN terminal.
Then connect a 75-ohm coaxial cable between theTO
TV terminal on the RF Modulator and the 75-ohm
VHF/UHF terminal on yourTV.
Note: If yourTV has only 300-ohm VHF screw terminals,
use a 75-ohm-to-300-ohm matching transformer to
complete the connection.
2. Plug the RF Modulator’s power cord into a standard AC
outlet.
If yourTV is not already connected to another VHF
source, connect a 75-ohm coaxial cable between to the
TOTV terminal on the RF modulator and the75-ohm
VHF/UHF terminal on yourTV.
OPERATION
1. Turn on theTV and set it to either Channel 3 or 4.
whichever is not used for regular broadcasts in your
area.
6
7
2. Set the RF Modulator’s CHANNEL 3/4 switch to the
same channel you set theTV (3 or 4).
SPECIFICATIONS
3.Turn on the connected video source and set OHMS
75/1K on the RF Modulator to the position that gives
the best picture.The video signal indicator on the RF
Modulator lights when the modulator is receiving a
signal for an A/V source.
Video Carrier Output Level . . . . . . . . . . . . . . . . . . . . . . . .69dB_V
RF Output Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 or 4
RF Output Impedance . . . . . . . . . . . . . . . . . . . . . . . . . . .75 Ohms
Video Input Impedance . . . . . . . . . . . . . . . . . .75 Ohms/1K Ohms
(Switchable)
Audio Input Impedance . . . . . . . . . . . . . . . . . . . . . . .13_3K Ohms
TV to ANT Insertion Loss 50 - 806 MHz . . . . . . . . . . . . . . . . .-2dB
Dimensions . . . . . . . . . . . . . . . . . . .513/16 x 31/16 x 17/16 inches
(148 x 78 x 37 mm)
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 lb 2.5 oz
.524 kg
CARE
To enjoy your RF Modulator for a long time:
• Keep the modulator dry. If it gets wet, wipe it dry
immediately.
Specifications are typical; individual units might vary.
Specifications are subject to change and improvement
without notice.
• Use and store the modulator only in normal temperature
environments.
• Handle the modulator gently and carefully. Don’t drop it.
• Keep the modulator away from dust and dirt.
•
Wipe the modulator with a damp cloth occasionally to
keep it looking new.
Modifying or tampering with the modulator’s internal
components can cause a malfunction and invalidate its
warranty and void your FCC authorization to operate it. If
your modulator is not performing as it should, take it to
your local store for assistance.
8
9
FCC Compliance Statement
90 DAY LIMITED WARRANTY: Jasco Products Co.,
Inc. warrants this product to be free from manufactur-
ing defects for a period of ninety days from the origi-
nal date of consumer purchase. This warranty is limit-
ed to the repair or replacement of this product only
and does not extend to consequential or incidental
damage to other products that may be used with this
unit. This warranty is in lieu of all other warranties
express or implied. Some states do not allow limita-
tions on how long an implied warranty lasts or permit
the exclusion or limitation of incidental or consequen-
tial damages, so the above limitations may not apply
to you. This warranty gives you specific rights, and
you may also have other rights which vary from state
to state. If unit should prove defective within the
warranty period, return prepaid with dated proof of
purchase to: Jasco Products Co., Inc., 311 N.W.
122nd, Oklahoma City, OK. 73114
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules.These limits are designed
to provide reasonable protection against harmful
interference in a residential installation.This equip-
ment generates, uses and can radiate radio frequency
energy and, if not installed or used in accordance
with the instructions, may cause harmful interference
to radio communications. However, there is no guar-
antee that interference will not occur in television
reception, which can be determined by turning the
equipment off and on, the user is encouraged to try
and correct the interference by one or more of the
following measures:
(1) Reorient or relocate the receiving antenna.
(2) Increase the separation between the equipment
and the receiver.
(3) Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.
(4) Consult the dealer or an experienced radio/TV
technician for help.
GARANTIA LIMITADA DE NOVENTA: Jasco Products., Co. Inc.
garantiza este producto por un periodo de noventa días desde la
fecha de la compra original, como libre de defectos de fabricación.
Esta garantía está limitada a la reparación o reemplazo de este pro-
ducto y no se extiende a daños consecuentes o incidentales en otros
productos que puedan ser usados con esta unidad. Esta garantía es
en vez de cualquier otra expresa o implícita. Algunos estados no
permite limitacíones al tiempo de limitada o permite el exclusión o
limitaciones del daños incidental o consiguiente, así el limitacíon
del arriba no aplicarse. Esta limitada darse justicia, y talvez tiene
otro justicias que cambia del estado a estado. Si la unidad resulta
defectuosa durante el periodo de garantía, devolverla prepagada a:
Jasco Products Co., Inc., 311 N.W. 122nd. Street, Oklahoma
City, OK. 73114
FCC WARNING:
Changes or modifications not expressly approved by
the party responsible for compliance could void the
user’s authority to operate the equipment.
10
11
Distributed for Thomson Consumer Electronics, Inc.
by Jasco Products, Co., Inc.,
311 N.W. 122nd Street,
Oklahoma City, Oklahoma 73114
|