RM24978
Universal Remote
Instruction Manual
Button Functions, cont.
Button Functions
Some buttons on the remote might have functions that
are referred to by different names on the device you are
controlling. E.G. PREV.CH may be called RECALL, or
ENTER may be called DISPLAY. These differences
depend on the brand and model of your product. Also,
this remote can only operate features that exist on your
product. E.G., your product must have PREV.CH ability
for the PREV.CH button to operate this feature.
CODESEARCH ON-OFF Turns
CHANNEL Up/Down
For setup.
product On or Changes the channels
Off.
TRACK +/- controls
DVD/CD track selection
i.e. DVD/CD Track Skip
Up/Down (in DVD and
CD modes).
INFO/DISPLAY button
brings up DVD Display or
Control Menu for Chapter/
Track/Title number, Time
remaining/elapsed
TV, VCR, etc.
Red Indicator
Selects product
to be operated.
Lights when any
button is pressed.
INPUT
For some TVs, press
repeatedly to select
from available
viewing sources
(antenna, cable box,
VCR, etc.).
indication, system infor-
mation, etc.
VOLUME UP/DOWN
Changes the volume
level of the product,
normally the TV.
PREV.CH Returns to
the previously selected
channel, or DVD repeat
toggle. REPEAT performs
DVD players “A-B Repeat”
(or RPT A.B) function for
repeat play of current
Chapter or Track.
CC (SUBTITLE)
TV Closed Caption
(if your TV has this
feature) or DVD
Subtitle toggle.
MUTE Turns off the
TV sound while the
picture remains.
RECORD, PLAY, STOP,
REW, FF, PAUSE VCR
control buttons operate
your VCR even when the
remote is set to operate the
TV. Also operates DVD
Scan -/+. Note the VCR
keys also control DVD
when in DVD Mode.
NUMBERS
Enter numbers for direct
channel selection. Some
products require ENTER
to be pressed after
channel selection.
OK Selects menu
items for the device
you are controlling.
ENTER
For some TV models,
used after direct
channel number
entry to immediately
change to the
RESUME, AUDIO, ZOOM,
ANGLE, TITLE Controls
DVD functions.
Note: The REC button must be pressed TWICE to
record from your VCR. For some brands of VCRs, you
might need to press the REC button once, then press it
again for three seconds.
selected channel.
MENU
Selects the on-
screen menu.
GUIDE displays satellite or cable
on-screen program guide.
4
5
DVD Functions
SAT Functions
This remote has several dedicated buttons used for
DVD functions. The descriptions may vary from your
original remote descriptions.
GUIDE/PROG button displays on-screen Satellite
Channel Guide.
CHANNEL+ and CHANNEL- buttons perform the
“Page+” and “Page-” function for on-screen Guide
Menus used by some Satellite systems.
INFO/DISPLAY button brings up Satellite Display
screen for current Channel and system information.
MENU brings up the Satellite Menu screen - use
with the UP, DOWN, LEFT & RIGHT navigation
buttons.
OK button is used for on-screen Menu selection.
EXIT button is used to Exit or Clear on-screen
Menu displays.
INPUT/SETUP button performs the Satellite TV/SAT
function.
SCAN+ and SCAN- buttons control the speed of
Fast Forward and Reverse Playback respectively.
SKIP (Channel Up & Down) buttons respectively
locate the succeeding or preceding Chapters or
Tracks on a disc.
SUBTITLE (CC) Turns the subtitles on or off.
TITLE Brings up the DVD Title Menu screen.
REPEAT A-B button performs DVD players “A-B
Repeat” (or RPT A.B) function for repeat play of
current Chapter or Track.
INFO/DISPLAY button brings up DVD Display or
Control Menu for Chapter/Track/Title number, Time
remaining/elapsed indication, system information,
etc.
MENU brings up the DVD disc Menu screen - use
with the UP, DOWN, LEFT & RIGHT navigation
buttons.
OK button is used for on-screen Menu selection.
Note some DVD players require the Play button to
be used.
EXIT Exit On-Screen Menus and/or Return to
previous On-Screen selection.
PLAY button is used to start Disc playback and for
Menu selection on some DVD players.
STOP button stops Disc playback.
PAUSE button pauses Disc playback - press PLAY
to resume.
OPEN/CLOSE Opens or closes the disc tray.
+10 Use with digit keys to select tracks greater
than 10.
GUIDE/PROG Program the playback order of
chapters or tracks on your disc.
AUDIO selects the audio language or sound during
disc playback.
SETUP/INPUT brings up the DVD Players Setup
Menu.
RESUME Continues disc playback from where you
stopped (if supported by your DVD player).
ANGLE selects the viewing angle during disc
playback.
ZOOM Zoom or enlarge a specific area of the
screen.
Note, not all DVD Players support all the functions
described above.
6
7
Code Search
Direct Code Entry
1. Press and hold the CODE SEARCH button
until the red indicator stays on, then
release the CODE SEARCH button.
If your device does not respond after you have tried
all the codes for your brand, or if your brand is not
listed, try searching for your code by following these
steps.
2. Press and release the desired mode
button (TV, VCR, etc.). The red indicator
blinks, then stays lit.
1. Manually turn on the device (TV, VCR, etc.) to be
controlled.
3. Enter the 4 digit code
from the code tables
(on separate sheet).
Note: after a valid code
entry, the red indicator
turns off. For an invalid
code, the red indicator
flashes.
2. Press and hold the CODE SEARCH
button until the red indicator stays on,
then release the CODE SEARCH button.
3. Press and quickly release the
desired mode button (TV, VCR, etc.).
The red indicator blinks off once.
4. Press the CHANNEL UP button
repeatedly (up to 300 times) until
the device to be controlled
changes channel. The red
4. With your device on, press ON/OFF.
If the device turns off, no further
programming is required. Note: If
some buttons do not operate your
equipment, try one of the other
codes for your brand.
indicator blinks off with each
button press. If you accidentally overshoot the
code required, press the CHANNEL DOWN button
to backtrack through the library until the device
changes channel. Pressing CHANNEL UP
changes direction to forward again.
Write your codes down here for easy reference
later.
5. Press and release ENTER to install the
Device Device stored
Code
code.
Most users will store VCR codes under the VCR button,
Cable codes under CABLE, etc. If (for example) you
want to store a VCR code under CABLE, first follow the
procedure for Direct Code Entry (page 8) and press
CABLE in step 2 of Direct Code Entry, then enter ANY
VCR code in step 3 of Direct Code Entry. Then follow
the steps above for Code Search.
TV
TV
SAT
VCR
DVD
CBL
AUDIO
AUX
Note: If the device does not have a CHANNEL UP
button, use PLAY (VCR only) or POWER instead. Code
Search starts from the currently stored four digit
number under that mode. Sometimes the first code
that “works” with your device may only allow limited
functionality (e.g. the MENU button might not work).
There may be a code that performs more functions.
Continue the code search process until the best code
is found.
8
9
UsingYour Remote, cont.
UsingYour Remote
Code Identification
Controlling Devices with Separate
Power On and Off Buttons
The Code Identification Feature allows you to
identify the four digit library code stored under your
device key. For example, if you want to find out what
four digit code is stored under your TV device key,
follow the six steps below:
Some GE, RCA and ProScan models require you to
press the device button for more than one second
to turn the device on and the POWER button to turn
the device off.
1. Press and hold the CODE SEARCH button
until the red indicator stays on.
Controlling Combo Devices
Release the CODE SEARCH button.
Some Combo devices (e.g. TV/VCR, TV/DVD,
DVD/VCR, etc.) will require you to set up two
different Mode buttons to control both parts of the
Combo device. For example, if you have a TV/DVD
Combo, you might need to set up one code under
the TV button to control the TV part AND a
separate code (under any other Mode button) to
control the DVD part.
2. Press and release the desired mode
button (TV, VCR, etc.). The red
indicator blinks, then stays lit.
3. Press and release the CODE SEARCH
button. The red indicator blinks once
and remains lit.
4. To find the first digit for
the code stored under
the mode key pressed
in step 2, press each
numeric key from 0-9
in turn. The number
that causes the
VCR/DVD Punch-Through
This remote allows the 6 VCR transport buttons
(i.e. PLAY, PAUSE, STOP, FF, REWIND, and REC)
to Punch-Through control from any Mode
programmed with TV, SAT or Cable codes to the
last VCR, or DVD programmed Mode you used.
This feature will not operate if the programmed TV,
SAT or Cable code has its own VCR transport
button control e.g. a TV Combo, SAT/PVR, etc.
indicator light to blink
is the first digit in your
code.
5. To find the second digit, repeat step 4.
6. Repeat step 4 to find the third and fourth digit.
This time the red indicator turns off and stays off.
10
11
UsingYour Remote, cont.
UsingYour Remote, cont.
Volume/Mute Control and Punch-
Through
Setting any Mode to use its own
Volume/Mute Control
This remote lets you select which device Mode
controls your Volume/Mute buttons. The remote is
initially set for all device Modes to use their own
Volume/Mute control if present. If the programmed
code has no Volume/Mute operation of its own then
those buttons will punch-through control to the TV
Mode device without needing to change to TV
Mode.
This routine can set any Mode to use only its own
Volume/Mute control. Note - If your chosen Mode
has no Volume/Mute functions of its own then the
Volume/Mute buttons will do nothing.
1. Press and hold the CODE SEARCH button
until the red indicator turns on, then
release the button.
Any Mode chosen for Volume/Mute control
MUST have its own Volume/Mute function or
the Volume/Mute buttons will do nothing.
2. Press and hold the MUTE button until
the red indicator blinks off, then release
the button.
3. Press and release the desired Mode
button (TV, VCR, etc.), the red indicator
blinks then stays on.
Setting ALL Volume/Mute Control to
any one Mode
This routine can set all Modes to “punch-through” to
any one chosen Mode for Volume/Mute button
control without the needing to change to that Mode.
4. Press and release the VOLUME-
(Down) button, the red indicator blinks
then stays on.
1. Press and hold the CODE SEARCH button
until the red indicator turns on, then
release the button.
5. Press and release the MUTE button and
the red indicator turns off.
2. Press and hold the MUTE button until the
red indicator blinks off, then release the
button.
Your chosen Mode will now use its own Volume/
Mute control.
3. Press and release the desired Mode button
(TV, VCR, etc.) for Volume/Mute control,
the red indicator blinks then stays on.
4. Press and release the MUTE button and
the red indicator turns off. The red indicator
will blink rapidly for three seconds if the
Mode you have selected has no Volume/
Mute control.
All other Modes will now punch-through to your
chosen Mode for Volume/Mute control.
12
13
90 Day Limited Warranty
Troubleshooting
Remote does not operate your product.
Jasco Products Company warrants this product to
be free from manufacturing defects for a period of
ninety days from the original date of consumer
purchase. This warranty is limited to the repair or
replacement of this product only and does not
extend to consequential or incidental damage to
other products that may be used with this unit. This
warranty is in lieu of all other warranties express or
implied. Some states do not allow limitations on
how long an implied warranty lasts or permit the
exclusion or limitation of incidental or consequential
damages, so the above limitations may not apply to
you. This warranty gives you specific rights, and
you may also have other rights which vary from
state to state. If unit should prove defective within
the warranty period, return prepaid with dated proof
of purchase to:
•
Press the mode button of the product you want
to control.
•
•
Program the remote with a new code.
Install new batteries. (You might have to
reprogram your remote after installing new
batteries.)
•
Remote may not be compatible with your
product.
Remote does not operate some features of
your product.
•
•
Sometimes a particular code might operate
some features but not all. Try programing
remote with a new code.
Remote may not be able to operate all features
of your product or button names might be
different than your product.
Jasco Products Company
311 N.W. 122nd
Oklahoma City, OK 73114
Red Indicator blinks after you program a
product code.
•
•
Remote did not accept the code.
Try to program the code again or try a different
code.
Lost Your Codes?
Enclosed with this remote is a sticker on which you
should write the codes for each device you
programmed. Apply the sticker to the back of the
remote or somewhere convenient for future
reference.
Also on the sticker is our website address which,
should you lose your codes or programming
instructions, you can find available on our website:
14
15
RM24978
Universal Remote
Instruction Manual
Jasco Products Company
311 N.W. 122nd
Oklahoma City, OK 73114
Made in China
RM24978-03/05
|