S
P
E
C
I
F
I
C
A
T
I
O
N
S
ENGINE
310SE
Type.............................................................................................................................John Deere 4045T – Turbocharged
Rated power @ 2,200 rpm ........................................................................................88 SAE gross hp (66 kW)
80 SAE net hp (60 kW)
Cylinders.....................................................................................................................4
Displacement.............................................................................................................276 cu. in. (4.524 L)
Fuel consumption, typical........................................................................................1.3 to 2.3 gal./hr. (4.9 to 8.7 L/h)
Torque rise .................................................................................................................42 percent
Maximum net torque.................................................................................................271 lb.-ft. (368 Nm)
Lubrication..................................................................................................................pressure system with spin-on filter and cooler
Air cleaner..................................................................................................................dual stage dry type with safety element and precleaner
Electrical system.......................................................................................................12 volt with 65-amp alternator
Sucker-type cooling fan
four-speed, helical cut gear, collar shift transmission synchronized in all gears with hydraulic
reverser
TRANSMISSION
Torque converter, single stage, dual phase with
2.63:1 stall ratio...................................................................................................11 in. (280 mm)
Travel speeds with 19.5L-24 rear tires Forward
Reverse
Gear 1...................................................................................................................3.6 mph (5.8 km/h)
Gear 2...................................................................................................................5.9 mph (9.5 km/h)
Gear 3...................................................................................................................14.4 mph (23.2 km/h)
Gear 4...................................................................................................................24.4 mph (39.3 km/h)
4.0 mph (6.4 km/h)
6.6 mph (10.6 km/h)
16.1 mph (25.9 km/h)
27.2 mph (43.8 km/h)
heavy-duty, inboard planetary final drives evenly distribute shock loads over three gears
hydraulic wet disk, mounted inboard, self adjusting and self equalizing
FINAL DRIVES
BRAKES
CAPACITIES
Fuel tank (with ground level fueling)......................................................................36 gal. (136 L)
Engine coolant...........................................................................................................17 qt. (16 L)
Engine oil including filter..........................................................................................9 qt. (8.5 L)
Torque converter and transmission.......................................................................15 qt. (14 L)
Hydraulic system.......................................................................................................24 gal. (91 L)
Rear axle.....................................................................................................................3.5 gal. (13 L)
Mechanical-front-wheel-drive axle.......................................................................2.3 gal. (8.5 L)
hydrostatic power steering and emergency steering conform to ISO5010
STEERING
Non-powered axle
Curb turning radius with brakes ......................................................................11 ft. 9 in. (3.57 m)
Without brakes............................................................................................13 ft. 3 in. (4.04 m)
Bucket clearance circle with brakes .............................................................31 ft. 6 in. (9.61 m)
Without brakes............................................................................................34 ft. 7 in. (10.55 m)
Steering wheel turns, stop to stop ..................................................................2.3 to 3.0
Mechanical-front-wheel-drive
Curb turning radius with brakes ......................................................................10 ft. 11 in. (3.34 m)
Without brakes ............................................................................................13 ft. 8 in. (4.17 m)
Bucket clearance circle with brakes .............................................................29 ft. 9 in. (9.07 m)
Without brakes............................................................................................35 ft. 3 in. (10.74 m)
Steering wheel turns, stop to stop ..................................................................2.5
Axle oscillations stop to stop, both axles..............................................................22 degrees
Axle ratings (SAE J43)
Front .....................................................................................................................18,860 lb. (8555 kg)
Rear ......................................................................................................................13,670 lb. (6200 kg)
HYDRAULIC SYSTEM
System.........................................................................................................................open center
Pressure
Backhoe...............................................................................................................3,625 psi (25 000 kPa)
Loader ..................................................................................................................3,000 psi (20 700 kPa)
Pump............................................................................................................................gear type, tandem with unloader
Flow @ 2,200 rpm
Backhoe...............................................................................................................36 gpm (136 L/min.)
Loader ..................................................................................................................28 gpm (106 L/min.)
Filter, return oil...........................................................................................................10-micron, spin-on enclosed replaceable element
16
L
I
F
T
C
A
P
A
C
I
T
I
E
S
*
/
D
I
M
E
N
S
I
O
N
S
*Lift capacities are over-end values in lb. (kg) according to SAE J31. Figures listed are 87% of the maximum lift force available. Base vehicle includes counterweight.
310SE BACKHOEWITH
TANDARD IPPERSTICK
310SE BACKHOEWITH 3-FT. 6-IN. (1.07
M
)
310SE BACKHOEWITH 3-FT. 6-IN. (1.07
M)
S
D
E
XTENDABLE IPPERSTICK, RETRACTED
D
E
XTENDABLE IPPERSTICK, EXTENDED
D
(SEE PAGE 19.)
DIMENSIONS
▲ ROPS and cab
18
D
I
M
E
N
S
I
O
N
S
BACKHOE
310SE
With Standard
Backhoe*
With Extendable Dipperstick*
Retracted
Extended
A
B
C
D
E
Loading height, truck loading position ..................................................................11 ft. 3 in. (3.43 m)
Reach from center of swing pivot..........................................................................18 ft. 3 in. (5.56 m)
Reach from center of rear axle...............................................................................21 ft. 9 in. (6.63 m)
Maximum digging depth...........................................................................................14 ft. 6 in. (4.42 m)
Digging depth (SAE):
11 ft. 7 in. (3.53 m)
18 ft. 7 in. (5.66 m)
22 ft. 1 in. (6.73 m)
14 ft. 11 in. (4.55 m)
14 ft. 1 in. (4.29 m)
21 ft. 11 in. (6.68 m)
25 ft. 4 in. (7.72 m)
18 ft. 5 in. (5.61 m)
(1) 2-ft. (610 mm) flat bottom....................................................................................14 ft. 4 in. (4.37 m)
(2) 8-ft. (2440 mm) flat bottom..................................................................................13 ft. 4 in. (4.06 m)
Ground clearance, minimum...................................................................................13 in. (330 mm)
Bucket rotation..........................................................................................................190 degrees
Transport height........................................................................................................11 ft. 6 in. (3.51 m)
Overall length, transport ..........................................................................................23 ft. 6 in. (7.16 m)
Stabilizer width – transport with ROPS .................................................................7 ft. 2 in. (2.18 m)
Stabilizer spread – operating..................................................................................10 ft. 2 in. (3.10 m)
Stabilizer overall width – operating .......................................................................11 ft. 7 in. (3.53 m)
Width over tires.........................................................................................................86 in. (2.18 m)
*Backhoe specifications are with 24-in. x 7.5-cu. ft. (610 mm x 0.21 m3) bucket.
14 ft. 9 in. (4.50 m)
13 ft. 9 in. (4.19 m)
13 in. (330 mm)
18 ft. 3 in. (5.56 m)
17 ft. 6 in. (5.33 m)
13 in. (330 mm)
F
G
H
I
190 degrees
190 degrees
11 ft. 5 in. (3.48 m)
23 ft. 6 in. (7.16 m)
7 ft. 2 in. (2.18 m)
10 ft. 2 in. (3.10 m)
11 ft. 7 in. (3.53 m)
86 in. (2.18 m)
11 ft. 5 in. (3.48 m)
23 ft. 6 in. (7.16 m)
7 ft. 2 in. (2.18 m)
10 ft. 2 in. (3.10 m)
11 ft. 7 in. (3.53 m)
86 in. (2.18 m)
J
K
L
M
LOADER PERFORMANCE WITH BUCKET OPTIONS
1.25 cu. yd.
(0.96 m3) Heavy-
duty Long Lip
1.30 cu. yd.
1.12 cu. yd.
(0.86 m3)
Multipurpose
1.25 cu. yd.
(0.96 m3)
Multipurpose
(1.00 m3) Heavy-
duty Long Lip
single lever
Operator control........................................................................................................single lever
Breakout force...........................................................................................................8,817 lb. (39.2 kN)
Lifting capacity, full height.......................................................................................6,247 lb. (2836 kg)
Height to bucket hinge pin, maximum ...................................................................11 ft. 2 in. (3.40 m)
Dump clearance, bucket at 45 degrees ................................................................8 ft. 2 in. (2.59 m)
Bucket dump angle, maximum................................................................................45 degrees
Reach at full height, bucket at 45 degrees ...........................................................36.0 in. (911 mm)
Rollback angle at ground level ...............................................................................40 degrees
Digging depth below ground, bucket level...........................................................5.8 in. (147 mm)
Raising time to full height.........................................................................................4.9 sec.
Bucket dump time .....................................................................................................1.1 sec.
Bucket lowering time (power down) .....................................................................1.9 sec.
single lever
single lever
8,900 lb. (39.6 kN)
6,150 lb. (2790 kg)
11 ft. 2 in. (3.40 m)
8 ft. 8 in. (2.64 m)
45 degrees
8,325 lb. (37.0 kN)
5,900 lb. (2676 kg)
11 ft. 2 in. (3.40 m)
8 ft. 7 in. (2.62 m)
45 degrees
8,300 lb. (36.9 kN)
5,800 lb. (2631 kg)
11 ft. 2 in. (3.40 m)
8 ft. 7 in. (2.62 m)
45 degrees
a
b
c
d
e
f
30.1 in. (765 mm)
40 degrees
32.2 in. (818 mm)
40 degrees
32.2 in. (818 mm)
40 degrees
8.1 in. (206 mm)
4.9 sec.
7.3 in. (185 mm)
4.9 sec.
7.3 in. (185 mm)
4.9 sec.
1.1 sec.
1.1 sec.
1.1 sec.
1.9 sec.
1.9 sec.
1.9 sec.
LIFT CAPACITY WITH QUICK COUPLER/FORKS
A1 Maximum height........................................................................................................4,178 lb. (1897 kg)
B1 Maximum reach.........................................................................................................6,191 lb. (2810 kg)
C1 At ground line.............................................................................................................8,232 lb. (3737 kg)
D1 Below ground line.....................................................................................................4.4 in. (112.7 mm) to bottom of tine / 2.7 in. (68.3 mm) to top of tine
19
A
D
D
I
T
I
O
N
A
L
E
Q
U
I
P
M
E
N
T
310SE
310SE
310SE
Backhoe bucket coupler for “C” and “D” series John
Deere buckets, Case buckets, and Cat buckets
Extendable dipperstick, 3 ft. 6 in. extension
Auxiliary backhoe valve for swingers, thumbs, etc.
Auxiliary backhoe valve for hammers, compactors
Auxiliary backhoe plumbing for hammers, compactors
SAE controlled load lowering device valves
■
Fuel gauge, illuminated electric
Gauge package, illuminated electric – Engine coolant
temperature / Transmission oil temperature / Alternator
volts / Fuel gauge
Monitor system with audible and visual warning – Engine
air filter restriction indicator / Alternator indicator /
Engine coolant temperature indicator with audible
warning / Engine oil pressure indicator with audible
warning / Hydraulic filter restriction indicator / Torque
converter oil temperature indicator / Parking brake on/
off indicator with audible warning / Seat belt indicator /
Mechanical-front-wheel-drive on/off indicator / Beacon
on/off indicator
●
■
ENGINE
John Deere Model 4045T – 4.5 liter, 80 SAE net hp turbo-
charged, isolation mounted
Vertical spin-on engine oil filter
Spin-on John Deere fuel filter with water separator
Oil-to-water engine oil cooler
Antifreeze, –34°F (–37°C)
Coolant recovery tank
Serpentine belt with automatic belt tensioner
Sucker-type cooling fan
Enclosed safety fan guard
High ambient temperature engine cooling
Dual element dry-type air cleaner
Muffler, underhood with curved-end exhaust stack
Chrome exhaust extension
Electric ether starting aid
Engine coolant heater, 1,000 watts
●
■
■
■
■
■
●
●
●
●
●
●
●
●
■
●
●
■
■
■
●
LOADER
Hydraulic self leveling
Return-to-dig feature
Single-lever control with electric clutch cutoff switch
Bucket-level indicator
Loader boom service lock
Auxiliary loader hydraulics with two-lever control
Loader front coupler
●
●
●
●
●
■
■
Seats and seat belts
Non-suspension vinyl swivel seat without armrests
Suspension vinyl swivel seat with armrests and lumbar
support
Suspension fabric swivel seat with armrests and
lumbar support
Air suspension vinyl swivel seat with armrests and
lumbar support
Air suspension fabric swivel seat with armrests and
lumbar support
2-in. seat belt with retractors
3-in. seat belt with retractors
Cab
Headliner
Dome light
Left cab door
Right cab door
Tinted safety glass
Two front and one rear windshield wipers
Front windshield washer
Fresh air intake heater/defroster/pressurizer – 40,000
Btu/hr. (11.7 kW) heater
Air conditioning – 26,000 Btu/hr. (7.6 kW) output / CFC-
free R134a refrigerant
65-amp alternator
●
■
Loader buckets
Less bucket, with bucket pins
Heavy-duty buckets with bolt-on cutting edge, skid
plates, and lift loops
Multipurpose buckets with bolt-on cutting edge, skid
plates, and lift loops
●
■
■
■
■
POWER TRAIN
Powershift transmission – Torque converter with electri-
cally actuated twist grip F-N-R in 1st through 4th gears
Transmission with powershift reverser and torque con-
verter – Fully synchronized four forward, four reverse
speeds / Isolation mounted to mainframe
Transmission oil cooler
Vertical spin-on transmission filter
Electric forward-neutral-reverse control lever with
neutral safety switch interlock
Electric clutch cutoff on gearshift and loader levers
Differential lock, electric foot-actuated
Planetary final drives
Hydraulic service brakes – Inboard, wet multi-disc, self
adjusting and self equalizing / Conform to SAE J1473
Parking/emergency brake with electric switch control –
Spring applied, hydraulically released wet multi-disc /
Independent of service brakes / Conforms to SAE J1473
Hydrostatic power steering with emergency manual mode
Non-powered front axle
Mechanical-front-wheel-drive with limited slip differential –
Electric on/off control / Drive-shaft guard / Sealed axle
Tires
11L-15 F3 front tires
11L-16 F3 front tires
12.5/80-18 traction front tires
16.9-24 R4 rear tires
19.5L-24 R4 rear tires
Rear wheel spacers for use with chains
■
●
■
HYDRAULIC SYSTEM
36 gpm (136 L/min.) tandem gear pump, open center system
Independent hydraulic reservoir
Hydraulic oil cooler
“O”-ring face seal connectors
10-micron vertical spin-on filter
●
●
●
●
●
●
■
■
●
●
●
■
●
●
■
●
●
●
●
●
●
●
●
ELECTRICAL
12-volt system
65-amp alternator
Single battery with 150-min. reserve capacity and 750 CCA
Dual batteries with 300-min. reserve capacity and 1,500 CCA
Positive terminal battery cover
Blade-type multi-fused circuits
By-pass start safety cover on starter
●
●
●
■
●
●
●
●
■
●
●
■
LIGHTS
●
■
■
■
Two front halogen driving/work lights, 32,500 candle-
power each
●
■
95-amp alternator
AM/FM/weatherband radio
Ride control
Two additional front halogen work lights, 32,500 candle-
power each
Two rear halogen work lights, 32,500 candlepower each
Two front and two rear turn signal/flashing
Two rear stop and tail
●
■
■
●
■
■
●
●
●
●
■
OVERALL VEHICLE
One-piece unitized construction mainframe
Vehicle tiedowns, two front and one rear
Remote grease bank for front axle
Rigid mounted front bumper
Front counterweights
400 lb. (181 kg)
650 lb. (295 kg)
900 lb. (408 kg)
1,150 lb. (522 kg)
●
●
●
●
Two rear reflectors
Rotating beacon
OPERATOR’S STATION
BACKHOE
■
■
■
■
■
●
●
■
●
Modular-design ROPS/FOPS canopy with molded roof –
Isolation mounted / Conforms to SAE J1040
Left and right front access
Slip-resistant steps and ergonomically located handholds
Molded floor mat
●
Backhoe with standard dipperstick, 14 ft. 6 in. digging depth
Backhoe controls
●
●
●
●
●
●
●
●
●
■
●
●
■
●
●
●
■
Two-lever (Deere) controls
Three-lever (Case) controls
Four-lever (Ford) controls
SAE excavator two-lever controls
Backhoe transport lock lever
Swing lock pin stored in operator’s station
Stabilizer valve with two-direction anti-drift valves
Pivoting stabilizers
With dirt pads
With reversible pads
Stabilizer cylinder guards
Backhoe buckets
●
■
■
■
●
●
●
1,400 lb. (635 kg)
Fuel tank, 36 gal. (136 L), ground level fueling
Engine sideshields with sliding service access door
Front grille screen
Vandal protection for instrument panel, engine access
doors, and fuel tank
Reverse warning alarm – Switchable to 97 dB(A) or
111 dB(A)
Dent-resistant rear fenders
Rear fender extensions
Front fenders*
SMV emblem
Rental decal kit
Special color paint*
Headliner
Coat hook
Built-in beverage and Thermos® bottle holders
Built-in Operator’s Manual storage compartment with manual
Interior rearview mirror
●
Outside rearview mirrors
Hand throttle with fuel economy setting at 2,100 rpm
Suspended foot throttle
Tilt steering
Horn
Key start switch with electric fuel shutoff
Hourmeter, illuminated electric
Tachometer/hourmeter, illuminated electric
●
■
■
●
■
■
■
■
■
■
Less bucket, with bucket pins
Standard duty with lift loops
Heavy duty with lift loops
●
■
■
■
Severe duty with lift loops
Quarter cab*
KEY:
●
Standard equipment
■
Optional or special equipment
*See your John Deere dealer for further information.
Net engine power is with standard equipment including air cleaner, exhaust system,
alternator, and cooling fan, at standard conditions per SAE J1349 and DIN 70 020,
using No. 2-D fuel at 35 API gravity. No derating is required up to 10,000 feet (3050 m).
Gross power is without cooling fan.
Specifications and design subject to change without notice. Wherever applicable, specifications are in
accordance with SAE standards. Except where otherwise noted, these specifications are based on a unit
with 19.5L-24, 8 PR R4 rear tires, 11L-16, 12 PR F3 front tires, 1.12 cu. yd. (0.86 m3) loader bucket, and
24 in. x 7.5 cu. ft. (610 mm x 0.21 m3) backhoe bucket.
20
DKA310SE Litho in U.S.A. (00-03)
|