MODEL
MODÈLE
MODELO
#840095
RECHARGEABLE JUMPSTARTER
INSTRUCTION MANUAL
MANUEL D’UTILISATION DE SYSTÈME DE DÉMARRAGE
RECHARGEABLE
MANUAL DE INSTRUCCIONES PARA EL SISTEMA DE
ARRANQUE ASISTIDO
THIS MANUAL CONTAINS IMPORTANT INFORMATION REGARDING SAFETY, OPERATION, MAINTENANCE AND STORAGE OF THIS
PRODUCT. BEFORE USE, READ CAREFULLY AND UNDERSTAND ALL CAUTIONS, WARNINGS, INSTRUCTIONS AND PRODUCT
LABELS. FAILURE TO DO SO COULD RESULT IN SERIOUS PERSONAL INJURY AND/OR PROPERTY DAMAGE.
CE MANUEL CONTIENT DES INFORMATIONS IMPORTANTES CONCERNANT LA SÉCURITÉ, LE FONCTIONNEMENT ET LE
REMISAGE DE CE PRODUIT. LIRE, ÉTUDIER ET VEILLER À BIEN COMPRENDRE TOUTES LES MISES EN GARDE ET INSTRUCTIONS
ET AUTOCOLLANTS APPOSÉS SUR LE PRODUIT AVANT DE L’UTILISER. NE PAS RESPECTER CES INSTRUCTIONS POURRAIT
ENTRAÎNER DES BLESSURES ET/OU DES DOMMAGES MATÉRIELS.
ESTE MANUAL CONTIENE INFORMACIÓN IMPORTANTE SOBRE LA SEGURIDAD, OPERACIÓN, MANTENIMIENTO Y ALMACE-
NAMIENTO DE ESTE PRODUCTO. ANTES DE USARLO, LEA Y COMPRENDA TODAS LAS PRECAUCIONES, ADVERTENCIAS,
INSTRUCCIONES Y ETIQUETAS DEL PRODUCTO. DE LO CONTRARIO PODRÍA SUFRIR LESIONES GRAVES O CAUSAR DAÑOS
MATERIALES.
IF YOU SHOULD HAVE ANY QUESTIONS OR EXPERIENCE A PROBLEM WITH YOUR ALLTRADE PRODUCT, DO NOT RETURN THIS
PRODUCT TO THE STORE. PLEASE CALL OUR CUSTOMER SERVICE DEPARTMENT AT 1-800-590-3723. BEFORE YOU CALL,
HAVE THE FOLLOWING INFORMATION AVAILABLE: MODEL No., DATE PURCHASED AND STORE LOCATION. AN ALLTRADE
REPRESENTATIVE CAN RESOLVE YOUR PROBLEM OVER THE PHONE. IF YOU WOULD LIKE TO MAKE A SUGGESTION OR
87-1904-60957
KAWASAKI™ IS A TRADEMARK LICENSED BY KAWASAKI™
MOTORS CORP., U.S.A., WHICH DOES NOT MANUFACTURE OR
DISTRIBUTE THIS PRODUCT. CONSUMER INQUIRES SHOULD BE
DIRECTED TO:
POUR TOUTE QUESTION OU EN CAS DE PROBLÈME AVEC LE PRODUIT ALLTRADE, NE PAS LE RETOURNER AU MAGASIN OÙ IL
A ÉTÉ ACHETÉ. APPELER LE SERVICE APRÈS-VENTEAU 1-800-590-3723. AVANT D’APPELER, VEILLER À SE PROCURER LES
INFORMATIONS SUIVANTES : No. DE MODÈLE, DATE DE L’ACHAT ET ADRESSE DU MAGASIN. UN REPRÉSENTANT D’ALLTRADE
PEUT RÉSOUDRE VOTRE PROBLÈME PAR TÉLÉPHONE. POUR TOUT COMMENTAIRE OU SUGGESTION, N’HÉSITEZ PAS À NOUS
APPELER OU NOUS CONTACTER PAR COURRIEL À L’ADRESSE : [email protected]. VOS COMMENTAIRES NOUS
SONT EXTRÊMEMENT PRÉCIEUX.
KAWASAKI™ EST UNE MARQUE DE COMMERCE DE KAWASAKI™
MOTORS CORP., U.S.A., QUI NE FABRIQUE PAS ET NE DISTRIBUE
PAS CE PRODUIT THIS PRODUCT. LES QUESTIONS DES CONSOM-
MATEURS DOIVENT ÊTRE ADRESSÉES À :
FOR CUSTOMER SERVICE
POUR LE SERVICE APRÉS VENTE
OU DU CONSOMMATEUR
KAWASAKI™ ES UNA MARCA REGISTRADA CON LICENCIA DE
KAWASAKI™ MOTORS CORP., E.U.A., QUE NO FABRICA NI
DISTRIBUYE ESTE PRODUCTO. LAS CONSULTAS DE LOS
CONSUMIDORES DEBEN DIRIGIRSE A:
PARA EL SERVICIO
PARA EL CONSUMIDOR
SI TIENE DUDAS O SURGEN PROBLEMAS CON SU PRODUCTO ALLTRADE, NO LO DEVUELVA A LA TIENDA LLAME A NUESTRO
DEPARTAMENTO DE SERVICIO AL CLIENTE AL 1-800-590-3723. ANTES DE LLAMAR, TENGA A MANO LA SIGUIENTE
INFORMACIÓN: No. DE MODELO, FECHA DE COMPRA Y DIRECCIÓN DE LA TIENDA. UN REPRESENTANTE DE ALLTRADE PUEDE
RESOLVER SU PROBLEMA POR TELÉFONO. SI DESEA HACER ALGUNA SUGERENCIA O COMENTARIO, LLÁMENOS O ENVÍENOS
UN MENSAJE DE CORREO ELECTRÓNICO A. INFO@ALLTRADETOOLS.COM. SUS COMENTARIOS SON FUNDAMENTALES PARA
NOSOTROS.
1-800-590-3723
Printed in China
Imprimé dans la Chine
Impreso en China
©COPYRIGHT 2005 ALLTRADE TOOLS, LLC.
1431 VIA PLATA
LONG BEACH, CA 90810-1462 USA
690095_Rechargable Jumpstarter, Système de démarrage recharge-
able, Sistema de arranque asistido
IMPORTANT SAFETY RULES FOR JUMPSTARTERS
!DANGER indicates an imminently hazardous
situation which, if not avoided, will result in death
or serious injury.
Read and understand all instructions, safety warnings, and
warning labels before attempting to use this jump-starter. Misuse can lead to
risk of fire, electric shock or personal injury.
!WARNING indicates a potentially hazardous
situation which, if not avoided, could result in
death or serious injury.
Lead-acid batteries generate explosive gases. Accidental
ignition by spark, cigarette or flame could lead to explosion or fire.
!CAUTION indicates a potentially hazardous
situation which, if not avoided, may result in
minor or moderate injury.
1. NEVER expose this product to rain, snow, ocean spray or any other damp
environments. Never immerse this product in water.
CAUTION used without the safety alert symbol
indicates a potentially hazardous situation which,
if not avoided, may result in property damage.
2. DO NOT use this jump-starter if it has been dropped, damaged or immersed in
liquid. Serious injury could occur.
3. Keep the area around the battery well ventilated. Build-up of gases could lead
to an explosion.
NOTE provides additional information that is useful
for proper use and maintenance of this tool. If a
NOTE is indicated make sure it is fully understood.
4. DO NOT smoke or light matches near battery.
5. ALWAYS wear eye protection when working with batteries. If battery acid
splashes into your eyes, flush immediately with cold running water.
Continue flushing for at least 15-20 minutes, then seek immediate medical
attention.
IMPORTANT SAFEGUARDS
People with electronic devices, such as pacemakers, should consult their
physician(s) before using this product. Operation of electrical equipment in
close proximity to a heart pacemaker could cause interference or failure of
the pacemaker.
6. NEVER wear a watch or metal pieces of jewelry near a lead-acid battery. If the
metal touches the battery, a short circuit could occur causing severe skin
damage.
7. Wear protective clothing. If battery acid gets on skin or clothing, wash the
affected area immediately with soap and water. If the skin becomes red,
sore or irritated, seek immediate medical attention.
WARNING: Some dust created by power sanding, sawing, grinding, drilling and
other construction activities contains chemicals known to the State of California
to cause cancer, birth defects or other reproductive harm.
8. Be careful not to drop a metal tool on the battery. It could cause a spark, short
circuit or explosion.
Some examples of these chemicals are:
• Lead from lead-based paints.
9. NEVER allow the black and red clamps to touch a metal surface or each other.
• Crystalline silica from bricks and cement and other masonry products,
and arsenic and chromium from chemically-treated lumber.
Store the clamps in their holders when not in use.
10.Keep this product out of the reach of children or untrained users.
Your risk from these exposures varies, depending on how often you do this type
of work. To reduce your exposure to these chemicals: work in a well ventilated
area, and work with approved safety equipment, such as dust masks that are
specially designed to filter out microscopic particles.
11.ALWAYS keep the unit in a dry, stable area when in use. Keep all cords and
body parts away from the vehicle’s moving engine.
12.Disconnect the negative (black) jumper cable FIRST. NEVER disconnect the red
WARNING: Handling the power cord on this product may expose you to lead, a
chemical known to the State of California to cause cancer and birth defects or
other reproductive harm. Wash hands after handling.
(positive) cable first unless the vehicle has a positive ground system.
4
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
13.Keep battery away from intense heat. An overheated battery may explode.
SYMBOLS
14.ALWAYS use an outlet equipped with a GFCI (ground fault circuit interrupter)
IMPORTANT: Some of the following symbols may be used on your tool. Please
study them and learn their meaning. Proper interpretation of these symbols will
allow you to operate the tool better and safer.
when charging the jump-starter in a damp or wet location.
IMPORTANT:
1. Recharge unit after each use. Use only the supplied AC charger and cords to
recharge the jump-starter. If you must use a DC power source, do not charge
for more than 4 hours or damage to the battery may occur.
SYMBOL
NAME
Volts
Amperes
Hertz
Watt
Kilograms
Alternating Current
Direct Current
EXPLANATION
Voltage (Potential)
Current
Frequency (Cycles per Second)
Power
Weight
Type of Current
Type of Current
V
A
Hz
W
Kg
2. Make sure the jump-starter is OFF before attempting to charge.
3. Use only manufacturer recommended accessories with this unit. NEVER put
anything into the power socket outlet except the cords supplied with this prod-
uct.
4. This product is not to be used with appliances that draw more than 20 amps.
5. For use with 12V DC battery systems only. Do not attempt to use with any
other types of batteries.
Alternating or Direct Current Type of Current
Earthing Terminal
Class II Construction
Minutes
Seconds
Diameter
Grounding Terminal
Denotes Double Insulation
Time
Time
Size of Drill Bits,
Grinding Wheels, etc.
No-load Rotational Speed
Revolutions, Surface Speed,
Strokes, etc. per Minute
Speed, Torque or Position Settings
6. DO NOT use this unit as a vehicular battery. This product is for jumpstarting
only. It will not replace a dead battery.
min
s
7. If the vehicle to be jumpstarted has an on-board computer system, check the
owner’s manual before attempting to jumpstart the engine. Jumpstarting with
this unit may cause damage to some computer systems.
8. Protect this product from moisture, excessive heat or direct sunlight.
9. Keep the unit upright at all times.
No load speed
Revolutions per Minute
.../min
10.Make sure all parts are in proper working order before each use. Replace dam-
aged parts immediately.
1,2,3, …
Ring Selector Settings
11.DO NOT immerse in liquid.
12.Never jumpstart a frozen battery.
13.DO NOT crank the vehicle’s engine excessively. If the vehicle will not start after
several attempts, the problem may be something besides the battery. Stop
jumpstarting and look for other causes.
14.NEVER over-inflate tires or other inflatable items.
EMERGENCY FIRST AID
Acid in Eyes. Flush immediately with cold running water. Continue flushing for at
least 15-20 minutes, then seek immediate medical attention.
Acid on Skin. Wash the affected area immediately with soap and water. If the skin
becomes red, sore or irritated, seek immediate medical attention.
5
6
BATTERY
CHARGING THE BATTERY
INITIAL CHARGE:
The Jumpstart System does not leave the factory fully charged. Before use, attach
the unit to the 120V AC charger for 48 hours. The green LED charge indicator will
show when the battery has reached full charge. To view the charge level, press the
Charge Status button.
Before using battery pack, please read carefully all instructions and cautionary
markings on battery pack, battery charger and product using battery.
Do not incinerate the battery pack even if it is severely damaged or is
completely worn out. The battery pack can explode.
RECHARGE:
The battery can be recharged using either AC or DC current. Cables are provided for
both sources of power. We recommend using the AC charger as charging with DC
power for long periods can damage the unit.
Do not carry battery packs in aprons, pockets, or tool boxes, product kit
boxes, drawers, etc. with loose metal objects. Battery pack terminals could
be short circuited causing damage to the battery pack, severe burns or fire.
CHARGING:
This unit contains a maintenance-free, non-spillable, sealed lead-acid bat-
tery, which must be recycled or disposed of properly. Contact your local waste
management authority for disposal locations in your area, or call 1-800-
CLEANUP.
ALWAYS recharge the jump-starter after use. Leaving the battery in a discharged
state will shorten the life of the battery.
Recharge the battery at least once a month, especially if it has not been in use.
Keeping the jump-starter fully charged will increase the life of the battery.
AC ADAPTER:
To charge this unit from a standard 120v household outlet, just plug the AC charg-
er/adapter into the socket. Use the barrel connector to plug the AC charger/adapter
into the recharge port on the jump-starter. Charge until the status indicator lights
show green.
The battery is not fully charged at the factory. Attach jump-starter to the 120V
AC charger for 48 hours before use. Unit will not overcharge when attached to
the AC charger.
Always switch to a fresh battery when tool performance begins to diminish.
Severe heat is most destructive to a battery; the more heat generated, the faster
the battery loses power. A battery that gets too hot can have a shortened life.
When first purchased, this unit should be charged for 48 hours to bring the battery
up to full working strength. After each use, recharge the battery for at least 14
hours. Charge once a month, even if the unit has been idle. Charging will help the
battery last longer.
Never over-discharge a battery by using the tool even after tool performance
has decreased. Do not attempt to discharge a tool’s battery by continuing to
pull on the tool trigger. When tool performance begins to diminish, stop the tool
and recharge the battery for optimal performance.
Charge battery pack at ambient temperatures between 50° F – 104° F.
Store tool and battery pack in locations where temperatures will not exceed
120°F. This is important to prevent serious damage to the battery cells.
When battery pack is not in use, keep it away from other metal objects such as
paper clips, coins, keys, nails, screws or other small metal objects that can
make a connection from one terminal to another. Shorting the battery terminals
together may cause sparks, burns, or fire.
7
8
DC ADAPTER:
FUNCTIONAL DESCRIPTION
To charge the jump-starter from a boat or car accessory receptacle, plug one end of
the included DC adapter into the receptacle and the other end into the accessory
socket on the jump-starter. Leave the vehicle running to prevent draining the vehi-
cle battery. Charge until the status indicator lights show green. DO NOT CHARGE
FROM A DC SOURCE FOR MORE THAN 4 HOURS. DAMAGE TO THE UNIT WILL
RESULT.
7
2
8
10
This method is not as effective as the AC method and should only be used if no AC
socket is available.
14
11
13
3
15
1
4
5
17
12
6
16
9
CONTROLS AND COMPONENTS:
1. On/Off Jumpstart Switch
2. Analog Pressure Gauge
3. Automotive Adapter
4. 12 Volt DC Accessory Outlet
5. Battery Charge Level Button
6. Battery Level Indicators
7. Work Light On/Off Switch
8. Work Light
10. Positive (Red) Jumper Cable
and clamp
11. Compressor On/Off Power
Switch
12. Recharging Port
13. 260 PSI compressor air hose
and tire chuck
14. Inflation adapters (nozzles)
15. Changing Status Indicator
16. Clamps Reverse Polarity Indicator
17. AC/DC Charging Adapter
9. Negative (Black) Jumper Cable
and clamp
9
10
OPERATING THE JUMPSTARTER
Before attempting to jumpstart any vehicle, read and
understand all safety warnings and instructions in this manual. Jumpstarting a
vehicle can be dangerous. Take all precautions recommended in this manual.
1. ALWAYS wear eye protection when working with batteries. If battery acid
splashes into your eyes, flush immediately with cold running water. Continue
flushing for at least 15-20 minutes, then seek immediate medical attention.
2. DO NOT smoke or light matches near battery. Batteries can emit explosive gases.
3. Wear protective clothing. If battery acid gets on skin or clothing, wash the
affected area immediately with soap and water. If the skin becomes red,
sore or irritated, seek immediate medical attention.
4. Contain long hair and remove jewelry before attempting to jumpstart the engine.
Do not wear vinyl clothing. Be extra careful when static electricity is present.
POSITIVE GROUND SYSTEMS ONLY
5. Never jumpstart a frozen battery.
If the vehicle has a positive ground system, attach the black (negative) clamp to the
vehicle battery’s negative terminal and attach the red (positive) clamp to the non-
moving metal body part.
6. Batteries emit hydrogen gas when charging. Keep away from flame. Avoid
breathing vapors.
7. Replace worn or damaged parts immediately.
5. Start the vehicle. Do not allow the starter to grind more than a couple of seconds.
8. Keep all clothing, cords, cables and body parts away from a running engine.
9. NEVER immerse this unit in fluid of any kind.
6. When the engine starts, remove the chassis clamp first, then the battery clamp.
Put the clamps back into their holders.
REVERSE POLARITY SWITCH
If you should inadvertently attach the positive (red) clamp to the battery’s negative
terminal or the negative (black) clamp to the battery’s positive terminal, an alarm
will sound. If you hear the alarm, immediately disconnect the cables and try again.
Once a correct connection is made, the internal switch will turn on, allowing you to
jumpstart your vehicle.
JUMPSTARTING A VEHICLE
1. Turn vehicle ignition to OFF and make sure all accessories are also turned off.
Put the vehicle in park. Set the emergency brake.
2. Put the jumpstart system in a dry, level location. Remove the jumper clamps
from their holders. (Squeeze on the handles and pull up.)
3. ALWAYS connect the red (positive) clamp first. Connect the red clamp to the
positive terminal on the vehicle’s battery. Attach the black (negative) clamp to
the chassis or a non-moving metal part of the vehicle. DO NOT attach to the
negative battery terminal or any moving parts.
FLOODING
Sometimes repeated attempts to start an engine will leave it flooded. If after sever-
al attempts, the engine still refuses to start, turn the ignition off and wait a while.
4. If the alarm sounds, disconnect the clamps (black clamp first) and switch.
12
USING THE AIR COMPRESSOR
ALWAYS disconnect the clamp connected to the vehicle
frame or engine FIRST.
TIRE INFLATION
1. Open the small compartment on the rear of the unit and pull out the air hose.
2. Push the connector onto the tire’s valve stem as far as possible and press the
thumb lock to hold it in place.
USING THE 12V POWER SUPPLY
3. Turn on compressor.
DO NOT use this product with appliances that draw more
than 8 amps.
4. Watch the pressure gauge. Be careful not to over-inflate the tire.
5. When the proper air pressure is reached, turn off the compressor.
6. Open the thumb lock and pull the connector free of the valve stem.
To use this unit as a power supply, simply plug your appliance’s 12V DC connector
into the DC accessory outlet and turn on the appliance.
7. Return air hose to storage compartment. Always leave the thumb lock open
when air hose is not in use.
USING THE WORK LIGHT
The emergency work light is located on the upper right corner of the jump-starter.
To operate, push the ON/OFF switch. When the unit is fully charged, this work light
will provide over 100 hours of illumination. ALWAYS turn the work light off before
charging or storage.
13
14
INFLATION USING A NOZZLE
1. Select the proper nozzle for the
job.
ACCESSORIES
Use only accessories that are recommended by the manufacturer for your model.
Accessories that may be suitable for one tool may become hazardous when used on
another tool.
2. Push the adapter into the con-
nector and lock into place with
the thumb lock.
Always attach grounded (3-prong) extension cords to grounded (3-hole) outlets.
If you must use an extension cord, be sure that the gauge is large enough to carry
the amount of current necessary for your power tool. If not, your tool may experi-
ence a loss of power, excessive voltage drop or overheating. The smaller the gauge
number, the heavier the cord (see table below).
3. Insert the adapter into the item
you wish to inflate. Remember
that most sports items inflate
very quickly.
4. Turn on the compressor
switch.
RECOMMENDED SIZES OF EXTENSION CORDS 120 VOLT AC 60 HZ TOOLS
TOOL CURRENT RATING
CONDUCTOR SIZE IN A.W.G
5. When the item is
inflated, turn off the
compressor.
AMPERE
3-6
6-8
8-10
10-12
12-16
16-20
10FT.
18
18
18
16
25FT.
18
18
18
16
50FT.
18
18
18
14
100FT.
18
16
14
14
-
6. Pull out the adapter.
7. Store hose and
nozzles.
14
12
12
12
12
12
-
SPECIFICATIONS
SPECIFICATIONS
Internal Battery
Jumpstart Current
Air Compressor Pressure
12V/18AH
350A (instant)
250PSI
MAINTENANCE AND CLEANING
DO NOT incinerate used batteries. Batteries will explode
if exposed to intense heat or flame.
OTHER CONSUMER DO-IT-YOURSELF (DIY) TOOLS
Alltrade offers a full range of Kawasaki™ tools that make DIY jobs easy. If you would
like further information on the following products, please contact Alltrade Customer
Service Department at 1-800-590-3723.
ALWAYS cover exposed terminals with heavy-duty electrical tape before disposal.
Unprotected terminals may short out and cause fire or personal injury.
This sealed lead-acid battery is recyclable. Please take used batteries to a city
battery drop-off center, lead-acid battery retailer or other battery recycling location.
Cordless Drills/Screwdrivers
Impact Wrenches
Sanders
Reciprocating Saws
Routers
Rotary Tools
Jigsaws
Corded and Cordless Multi-Purpose Tools
Wide Range of Accessories and more
Circular Saws
Angle Grinders
15
found to be defective and subject to warranty. Alltrade retains the sole discretion
to determine whether any item or part is nonconforming and, if so, whether the
item and/or part will be repaired and/or replaced. If the unit is repaired, new or
reconditioned replacement parts may be used. If Alltrade chooses to replace
the product, it may replace it with a new or reconditioned one of the same or
comparable design. The repaired or replaced unit will be warranted under the terms
of the remainder of the warranty period. Typically, a defective product that is
returned within the first 30 days after the purchase date will be replaced; for items
returned after the first 30 days and within the warranty period, covered defective
parts not subject to normal wear and tear or other exclusions will be repaired or
replaced, at Alltrade’s option. During the warranty period, Alltrade will be responsi-
ble for the return shipping charges. Alltrade’s repair and/or replacement of any non-
conforming item and/or part thereof shall constitute fulfillment of all
obligations to the purchaser. Alltrade shall not be responsible or liable for any
expense, including freight charges, or repairs made outside Alltrade’s facility, unless
expressly agreed to by Alltrade in writing. Under no circumstances shall Alltrade
bear any responsibility for loss of the unit, loss of time or rental, inconvenience,
commercial loss or consequential damages.
2 YEAR LIMITED HOME USE WARRANTY
Express and Exclusive Limited Home Use Warranty to Original Retail Buyer
Alltrade Tools LLC (hereinafter "Alltrade") expressly warrants to the original retail
purchaser of the accompanying KAWASAKI™ portable power tool and no one else
all parts of the product (except those parts referred to below which are specifically
excluded from such warranty (see Exclusions)) to be free from defects in materials
and workmanship for a period of two years from original date of purchase.
SPECIAL WARRANTY NOTE TO CONTRACTORS AND COMMERCIAL USERS: This
Kawasaki™ portable power tool is offered as a home use tool and carries a HOME
USE WARRANTY. This tool is made for home use in the execution of
projects and repairs in and around the home. Use of the tool for COMMERCIAL
PURPOSES OR ON A JOBSITE is not covered under this warranty.
The date of purchase shall be the date of shipment to the original purchaser, or the
date the original purchaser took possession, custody or control of the product,
whichever occurred first. This warranty shall be null and void if the product or any
component thereof is modified, altered or used for any commercial purpose or on
a jobsite. This warranty does not apply to any other product and/or component
thereof manufactured or distributed by Alltrade, and does not apply to products
and/or components thereof designed, manufactured and/or assembled by others,
for which Alltrade makes no warranties whatsoever. THERE ARE NO WARRANTIES
WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF.
Exclusions
This warranty does not cover parts damaged due to normal wear, abnormal
conditions, misapplication, misuse, abuse, accidents, operation at other than
recommended pressures or temperatures, improper storage or freight damage.
Parts damaged or worn by operation in dusty environments are not warranted.
Failure to follow recommended operating and maintenance procedures also
voids warranty.
Warranty Performance
By purchasing the product, purchaser expressly acknowledges and agrees that their
sole and exclusive remedy under this warranty shall be strictly limited to the repair
or replacement of any covered nonconforming items or parts thereof provided that
any such nonconforming item and/or part is promptly returned to Alltrade’s facility
postage pre-paid and insured (address: ALLTRADE Warranty Claims & Repair,
1431 Via Plata, Long Beach, CA 90810, Attn: Customer Service #310-522-9008)
within the applicable warranty period, with a written request by purchaser that
Alltrade repair and/or replace the nonconforming item and/or part. We recommend
that you keep the original product packaging in the event you need to ship the unit.
We suggest the package be insured against loss or in transit damage. When
sending your product include your name, address, phone number, dated proof
of purchase (or copy), and a statement about the nature of problem. Warranty
coverage is conditioned upon purchaser furnishing Alltrade with adequate written
proof that they are the original purchaser and of the original purchase date. Parts
returned, freight prepaid and insured, to Alltrade’s facility (see above address) will
be inspected and, at Alltrade’s option, repaired and/or replaced free of charge if
This limited warranty does not apply to accessory items such as drill bits,
screwdriving bits, circular saw blades, jigsaw blades, grinding wheels, sanding
sheets and other related items.
DAMAGE TO THE PRODUCT RESULTING FROM TAMPERING, ACCIDENT, ABUSE,
NEGLIGENCE, FAILURE TO FOLLOW INSTRUCTIONS, UNAUTHORIZED REPAIRS
OR ALTERATIONS, DAMAGE WHILE IN TRANSIT TO OUR SERVICE FACILITY,
USE OF UNAPPROVED OR IMPROPER ATTACHMENTS OR ACCESSORIES,
COMMERCIAL AND RENTAL APPLICATIONS OR OTHER CAUSES UNRELATED TO
PROBLEMS WITH MATERIAL OR WORKMANSHIP ARE NOT COVERED BY THIS
WARRANTY.
Alltrade will not be liable for the following: labor charges, loss or damage resulting
from improper operation, maintenance or repairs made by other persons;
pre-delivery services such as assembly, oil or lubricants, and adjustment;
maintenance services that are normally required to maintain the product.
The use of other than genuine Alltrade Repair Parts will void warranty.
17
18
Warranty Disclaimers
REPRESENTATIVE(S) HAS BEEN ADVISED OF THE POSSIBILITY OF ANY SUCH
DAMAGES. IN NO EVENT, WHETHER AS A RESULT OF A BREACH OF CONTRACT,
WARRANTY, TORT (INCLUDING NEGLIGENCE) OR OTHERWISE, SHALL
ALLTRADE’S AND/OR ITS REPRESENTATIVE(S)’ LIABILITY EXCEED THE PRICE OF
THE PRODUCT. ANY AND ALL LIABILITY CONNECTED WITH THE USE OF
THIS PRODUCT SHALL TERMINATE UPON THE EXPIRATION OF THE WARRANTY
PERIODS SPECIFIED ABOVE.
EXCLUSION AND DISCLAIMER OF ALL OTHER EXPRESS WARRANTIES,
GUARANTIES AND/OR REPRESENTATIONS. EXCEPT FOR THE LIMITED WARRANTY
PROVIDED ABOVE, ALL OTHER EXPRESS WARRANTIES, GUARANTIES AND/OR
REPRESENTATIONS BY ALLTRADE AND/OR ITS REPRESENTATIVE(S) REGARDING
THE DESIGN, MANUFACTURE, PURCHASE, USE AND/OR OPERATION OF THE
PRODUCT OR ANY COMPONENT THEREOF SOLD HEREUNDER, REGARDLESS OF
WHETHER ANY SUCH WARRANTY, GUARANTY AND/OR REPRESENTATION,
WRITTEN OR ORAL, ARISES BY OPERATION OF LAW AND/OR EQUITY AND/OR BY
ANY ACT OR OMISSION OF ALLTRADE AND/OR ITS REPRESENTATIVE(S), OR THE
BUYER, ARE HEREBY EXPRESSLY EXCLUDED AND DISCLAIMED BY ALLTRADE
AND/OR ITS REPRESENTATIVES. PURCHASER KNOWINGLY AND WILLINGLY
WAIVES ANY AND ALL SUCH WARRANTIES AND RIGHTS, CLAIMS AND/OR
CAUSES OF ACTION ARISING THEREFROM OR BASED THEREON. PURCHASER’S
SOLE AND EXCLUSIVE REMEDY IS AS STATED ABOVE.
Limitations on Warranty Disclaimers
Some states do not allow limitations on how long an implied warranty lasts
and some states do not allow the exclusion or limitation of the incidental or
consequential damages, so part or all of the above limitations or exclusions may not
apply to you. This warranty gives you specific legal rights, and you may also have
other rights which vary from state to state.
If your product is not covered by this warranty, please call our Customer Service
Department at 1-310-522-9008 or toll free at 1-800-590-3723 for general repair
information and charges.
EXCLUSION AND DISCLAIMER OF ALL IMPLIED WARRANTIES, INCLUDING THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. NO WARRANTY, ORAL OR WRITTEN, OTHER THAN THE ABOVE
WARRANTY IS MADE WITH REGARD TO THIS PRODUCT. ALL EXPRESS AND/OR
IMPLIED WARRANTIES, GUARANTIES AND/OR REPRESENTATIONS BY ALLTRADE
AND/OR ITS REPRESENTATIVE(S) REGARDING THE DESIGN, MANUFACTURE,
PURCHASE, USE AND/OR OPERATION OF THE PRODUCT OR ANY COMPONENT
THEREOF SOLD HEREUNDER, REGARDLESS OF WHETHER ANY SUCH WARRANTY,
GUARANTY AND/OR REPRESENTATION, WRITTEN OR ORAL, ARISES BY
OPERATION OF LAW AND/OR EQUITY AND/OR BY ANY ACT OR OMISSION OF
ALLTRADE AND/OR ITS REPRESENTATIVE(S), OR THE PURCHASER, INCLUDING
BUT NOT LIMITED TO THE IMPLIED WARRANTY OF MERCHANTABILITY AND THE
WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY EXPRESSLY
EXCLUDED AND DISCLAIMED BY ALLTRADE AND/OR ITS REPRESENTATIVES.
PURCHASER KNOWINGLY AND WILLINGLY WAIVES ANY AND ALL SUCH
WARRANTIES AND RIGHTS, CLAIMS AND/OR CAUSES OF ACTION ARISING
THEREFROM OR BASED THEREON. PURCHASER’S SOLE AND EXCLUSIVE
REMEDY IS AS STATED ABOVE.
Limitation Of Liability
IN NO EVENT SHALL ALLTRADE AND/OR ITS REPRESENTATIVE(S) BE LIABLE FOR
INDIRECT, INCIDENTAL, SPECIAL AND/OR CONSEQUENTIAL DAMAGES OF ANY
KIND ARISING OUT OF OR RELATED TO, DIRECTLY OR INDIRECTLY, ANY BREACH
OF ANY PROVISION OF ANY AGREEMENT BETWEEN ALLTRADE AND/OR ITS
REPRESENTATIVE(S) AND PURCHASER, ANY WARRANTY HEREUNDER,
AND/OR THE EXISTENCE, DESIGN, MANUFACTURE, PURCHASE, USE AND/OR
OPERATION OF ANY ITEM(S) SOLD HEREUNDER EVEN IF ALLTRADE AND/OR ITS
19
20
|