MODEL
840444
19.2V BATTERY-OPERATED
HANDHELD VACUUM
BATTERIES AND CHARGERS
SOLD SEPARATELY
Conforms to UL Std. 1017
FOR CUSTOMER SERVICE
POUR LE SERVICE APRÉS VENTE
OU DU CONSOMMATEUR
87-1904-60957
THIS MANUAL CONTAINS IMPORTANT INFORMATION REGARDING SAFETY, OPERATION, MAINTENANCE AND STORAGE OF THIS
PRODUCT. BEFORE USE, READ CAREFULLY AND UNDERSTAND ALL CAUTIONS, WARNINGS, INSTRUCTIONS AND PRODUCT
LABELS. FAILURE TO DO SO COULD RESULT IN SERIOUS PERSONAL INJURY AND/OR PROPERTY DAMAGE.
PARA EL SERVICIO
PARA EL CONSUMIDOR
KAWASAKI™ IS A TRADEMARK LICENSED BY KAWASAKI™ MOTORS
CORP., U.S.A., WHICH DOES NOT MANUFACTURE OR
DISTRIBUTE THIS PRODUCT. CONSUMER INQUIRES SHOULD BE
DIRECTED TO:
IF YOU SHOULD HAVE ANY QUESTIONS OR EXPERIENCE A PROBLEM WITH YOUR ALLTRADE PRODUCT, DO NOT RETURN THIS
PRODUCT TO THE STORE. PLEASE CALL OUR CUSTOMER SERVICE DEPARTMENT AT 1-800-590-3723. BEFORE YOU CALL,
HAVE THE FOLLOWING INFORMATION AVAILABLE: MODEL No., DATE PURCHASED AND STORE LOCATION. AN ALLTRADE
REPRESENTATIVE CAN RESOLVE YOUR PROBLEM OVER THE PHONE. IF YOU WOULD LIKE TO MAKE A SUGGESTION OR
COMMENT, GIVE US A CALL OR EMAIL US AT: INFO@ALLTRADETOOLS.COM. YOUR FEEDBACK IS VITAL TO US.
1-800-590-3723
©COPYRIGHT 2007 ALLTRADE TOOLS, LLC.
1431 VIA PLATA
LONG BEACH, CA 90810-1462 USA
Printed in China
Imprimé dans la Chine
Impreso en China
840444 – 19.2V Handheld Vacuum_Rev 7/28/07
WORK AREA
CAUTION
indicates a potentially hazardous
situation which, if not avoided, may result in
minor or moderate injury.
Keep your work area clean and well lit.
areas may cause accidents or injury.
Cluttered work benches and dark work
CAUTION
used without the safety alert symbol
indicates a potentially hazardous situation which,
if not avoided, may result in property damage.
Do not operate power tools in explosive areas, such as in the presence of
flammable liquids, gases or dust.
the dust or fumes.
Power tools create sparks which may ignite
NOTE
provides additional information that is useful
for proper use and maintenance of this tool. If a
NOTE is indicated make sure it is fully understood.
Keep bystanders, children and visitors away while operating a power tool.
Distractions can cause you to lose control.
IMPORTANT SAFEGUARDS
ELECTRICAL SAFETY
People with electronic devices, such as pacemakers, should consult their
physician(s) before using this product. Operation of electrical equipment in
close proximity to a heart pacemaker could cause interference or failure of
the pacemaker.
Do not abuse the cord. Never use the cord to carry the tool. Keep the cord
away from heat, oil, sharp edges, or moving parts. Replace damaged cords
immediately.
Damaged cords may create a fire.
A battery operated tool with integral batteries or a separate battery pack
must be recharged only with the specified charger for the battery.
WARNING:
Some dust created by power sanding, sawing, grinding, drilling and
A charger
other construction activities contains chemicals known to the State of California
to cause cancer, birth defects or other reproductive harm.
that may be suitable for one type of battery may create a risk of fire when used with
another battery.
Some examples of these chemicals are:
• Lead from lead-based paints.
Use battery operated tool only with specifically designated battery pack.
Use of
any other batteries may create risk of fire.
• Crystalline silica from bricks and cement and other masonry products,
and arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type
of work. To reduce your exposure to these chemicals: work in a well ventilated
area, and work with approved safety equipment, such as dust masks that are
specially designed to filter out microscopic particles.
WARNING:
Handling the power cord on corded products may expose you to
lead, a chemical known to the State of California to cause cancer and birth
Wash hands after handling.
defects or other reproductive harm.
3
4
PERSONAL SAFETY
When battery pack is not in use, keep it away from other metal objects like:
paper clips, coins, keys, nails, screws, or other small metal objects that can
Stay alert, watch what you are doing, and use common sense when operat-
ing a power tool. Do not use tool while tired or under the influence of drugs,
make a connection from one terminal to another.
Shorting the battery termi-
nals together may cause sparks, burns or a fire.
alcohol or medication.
A moment of inattention while operating power tools
may result in serious personal injury.
Maintain tools with care. Keep cutting tools sharp and clean
. Properly maintained
tools with sharp cutting edge are less likely to bind and are easier to control.
Dress properly. Do not wear loose clothing or jewelry. Contain long hair.
Keep your hair, clothing, and gloves away from moving parts.
jewelry or long hair can be caught in moving parts.
Loose clothes,
Check for misalignment or binding of moving parts, breakage of parts, and any
other condition that may affect the tool’s operation. If damaged, have the tool
serviced before using.
Many accidents are caused by poorly maintained tools.
Use only accessories that are recommended by the manufacturer for your
model.
Avoid accidental starting. Be sure switch is in the locked or “OFF” position
before inserting battery pack.
Carrying power tools with your finger on the
“ON”
switch or inserting battery pack into a tool with the power switch
accidents.
invites
Accessories that may be suitable for one tool may create a risk of injury
when used on another tool.
Remove adjusting keys or wrenches before turning the tool “ON”.
or a key that is left attached to a rotating part of the tool may result in person-
al injury.
A wrench
SERVICE
Do not overreach. Keep proper footing and balance at all times.
ing and balance enable better control of the tool in unexpected situations.
Proper foot-
Tool service must be performed only by qualified repair personnel.
Service
or maintenance by unqualified personnel may result in a risk of injury.
Use safety equipment. Always wear eye protection.
ty shoes, hard hat, or hearing protection must be used for appropriate conditions.
Dust mask, non-skid safe-
When servicing a tool, use only identical replacement parts. Follow instruc-
tions in the Maintenance section of this manual.
Use of unauthorized parts or
failure to follow Maintenance Instructions may create a risk of shock or injury.
TOOL USE AND CARE
SPECIFIC SAFETY RULES AND/OR SYMBOLS
Use clamps or other practical ways to secure and support the workpiece to a
Hold tool by insulated gripping surfaces when per-
forming an operation where the cutting tool may contact hidden wiring.
Contact with a “live” wire will also make exposed metal parts of the tool
“live” and shock the operator.
stable platform.
Holding the work by hand or against your body is unstable and
may lead to loss of control.
Do not force tool. Use the correct tool for your application.
The correct tool
will do the job better and safer at the rate for which it is designed.
Do not use the tool if the power switch does not turn it “ON” or “OFF”.
cannot be controlled with the switch is dangerous and must be repaired.
A tool that
SAFETY RULES FOR CORDLESS VACUUMS
Disconnect battery pack from tool or place the switch in the locked or “OFF” posi-
tion before making any adjustments, changing accessories, or storing the tool.
Such preventative safety measures reduce the risk of starting the tool accidentally.
FOR INDOOR USE ONLY.
This vacuum is intended for picking up dry materials ONLY.
pick up any fluids, especially fluids which are flammable or solvent-based.
Vacuuming fluids or combustible material may lead to risk of fire.
Do not attempt to
Store idle tools out of reach of children and other untrained persons.
Tools
are dangerous in the hands of untrained users.
5
FUNCTIONAL DESCRIPTION
CONTROLS AND COMPONENTS:
NEVER vacuum up smoldering cigarette butts or any other burning material.
This may cause the unit to burst into flame.
1
1. ON/OFF Switch
2. Dust Cup release button
3. Dust Cup
2
Keep the ventilation openings clear of dust, hair, paper or any other items
that may restrict air flow.
4. Air Intake
5. Filter Bracket
Never use the vacuum if the filter is wet or missing.
(located inside dust cup)
6. Filter
8
Do not point the nozzle or exhaust vents toward your eyes, ears or hair.
3
Do not use this vacuum for more than ten minutes at a time.
It is not designed
(located inside filter bracket)
for extended use.
7. Crevice Tool
8. Brush
Always turn the switch “OFF” and remove the battery pack before servicing.
6
4
SYMBOLS
5
7
IMPORTANT:
Some of the following symbols may be used on your tool. Please
study them and learn their meaning. Proper interpretation of these symbols will
allow you to operate the tool better and safer.
BATTERY
SYMBOL
NAME
EXPLANATION
Before using battery pack, please read carefully all instruc-
tions and cautionary markings on battery pack, battery
charger and product using battery.
V
A
Hz
W
Kg
Volts
Amperes
Hertz
Voltage (Potential)
Current
Frequency (Cycles per Second)
Power
Weight
Type of Current
Type of Current
®
Do not incinerate the battery pack even if it is severely
Watt
damaged or is completely worn out.
The battery pack can
explode.
Kilograms
Alternating Current
Direct Current
Do not carry battery packs in aprons, pockets, or tool boxes, product kit
boxes, drawers, etc. with loose metal objects.
Battery pack terminals could
be short circuited causing damage to the battery pack, severe burns or fire.
Alternating or Direct Current Type of Current
Earthing Terminal
Class II Construction
Minutes
Seconds
Diameter
Grounding Terminal
Denotes Double Insulation
Time
Time
Size of Drill Bits,
The battery pack is Nickel-Cadmium (Ni-Cad) and is considered to be a toxic
material by the Environmental Protection Agency.
Before disposing of dam-
aged or worn out Ni-Cad battery packs, check with your State Environmental
Protection Agency to find out about special restrictions on the disposal of these
battery packs, take them to your local recycling center for proper disposal, or
min
s
1-800-822-8837
call
.
Grinding Wheels, etc.
No load speed
No-load Rotational Speed
.../min
Revolutions per Minute
Revolutions, Surface Speed,
Strokes, etc. per Minute
1,2,3, …
Ring Selector Settings
Speed, Torque or Position Settings
8
REMOVING/ATTACHING BATTERY PACK
REMOVE BATTERY PACK:
1. Press both release but-
tons on either side of
Use only Kawasaki™ 19.2V Battery Pack #691034 or
#691240 with the One Hour Charger #690507 or Charger #690072/ Adapter
#690074.
the Cordless Vacuum to
release the battery pack.
2. Pull battery pack free of
Cordless Vacuum.
RELEASE BUTTON
The battery is not fully charged.
Charger #690072/ Adapter #690074 -
requires 8-10 hours charge time to be fully charged. Subsequent recharging
needs 3-5 hours for the battery to be fully charged.
Before first use, the battery pack
ATTACH BATTERY PACK:
1. Align the raised portion of the battery pack with the groove in the battery com-
partment of the Cordless Vacuum.
One Hour Charger #690507 -
hours charge time to be fully charged. Subsequent recharging needs 1 hour for
the battery to be fully charged.
Before first use, the battery pack requires 3-5
2. Press the battery pack into place. Make sure the latches are securely fastened.
Do not use the Cordless Vacuum if the battery pack is not seated properly.
CHARGER #690072 / ADAPTER #690074
Always switch to a fresh battery when tool performance begins to diminish.
Severe heat is most destructive to a battery; the more heat generated, the faster
the battery loses power. A battery that gets too hot can have a shortened life.
Before using battery charger, please read carefully all
instructions and cautionary markings on battery charger, battery pack and
product using battery.
Never over-discharge a battery by using the tool even after tool performance
has decreased.
Do not attempt to discharge a tool’s battery by continuing to
pull on the tool trigger. When tool performance begins to diminish, stop the tool
and recharge the battery for optimal performance.
The charger will not automatically turn “OFF” when the
battery pack is fully charged. The charging indicator light will remain “ON”
until the charger is disconnected from the electrical outlet. To prolong
battery life, REMOVE battery from charger after 3-5 hours of recharging.
Charge battery pack at ambient temperatures between 50° F – 104° F.
Store tool and battery pack in locations where temperatures will not exceed
120°F.
This is important to prevent serious damage to the battery cells.
The battery pack should always be recharged when the Cordless Vacuum begins
to run slowly.
Use only the charger which accompanied your product or direct replacement as
listed in this manual.
Do not substitute any other charger. Use only Alltrade
approved chargers with your product.
When battery pack is not in use, keep it away from other metal objects such as
paper clips, coins, keys, nails, screws or other small metal objects that can
Do not disassemble charger.
make a connection from one terminal to another.
Shorting the battery terminals
Do not use charger if it has been damaged, left outdoors in the rain, snow, wet
or damp environments, or immersed in liquid.
together may cause sparks, burns, or fire.
The battery pack and charger heat during charging.
Place the charger on a flat,
non-flammable surface away from flammable materials with at least four inches of
clearance to allow proper air circulation around the charger and battery pack.
When the battery pack requires recharging, a 3-5 hour charge allows the tool to
operate at full power.
A charging indicator light on the charger will illuminate to
show that charging is taking place.
10
The battery pack and charger heat during charging.
Place the charger on a flat,
CHARGING BATTERY PACK USING CHARGER #690072 / ADAPTER #690074
non-flammable surface away from flammable materials with at least four inches of
clearance to allow proper air circulation around the charger and battery pack.
BATTERY PACK
CHARGE BATTERY PACK:
1. Make sure the trigger on
the Cordless Vacuum is in
When the battery pack requires recharging, a 1 hour charge allows the tool to
operate at full power.
A charging indicator light on the charger will illuminate to
120V AC
ADAPTER
“OFF”
the
position and
show that charging is taking place.
remove the battery pack
from the Cordless Vacuum.
CHARGING BATTERY PACK USING ONE HOUR CHARGER #690507
2. Insert the battery pack into
the charger. Be sure that
the battery pack is fully
seated in the charger. Do
not force.
BATTERY PACK
CHARGE BATTERY PACK:
1. Plug the charger into the
nearest 120 volt electrical
outlet. The step of the battery
has positive and negative ter-
minal markings on it. Align
the markings with the identi-
cal markings on the top of
the charger base. Insert the
battery pack into base. Pack
will not insert properly if
reversed.
LED LIGHT
3. Plug the charger into the
nearest 120 volt, electrical
outlet. The indicator light will come
BATTERY
CHARGER
“ON”
.
IMPORTANT INFORMATION FOR RECHARGING HOT BATTERIES
When using your Cordless Vacuum continuously, the batteries in your battery pack
will become hot. You should let a hot battery pack cool down for approximately 30
minutes before attempting to recharge. When the battery pack becomes discharged
and is hot, the red light on the charger will flash. When the battery pack cools down,
the red light will glow continuously.
2. Make sure the trigger on the
Cordless Vacuum is in the
BATTERY
CHARGER
“OFF”
position and remove
the battery pack from the Cordless Vacuum.
This will occur when continuous use of your Cordless
Vacuum causes the battery pack to become hot.
mal circumstances.
It does not occur under nor-
“ON”
3. If, when first inserting the battery pack, the red
button does not light up,
press the “SET” button on the charger. When the battery is charging, the red
“ON”
light is
4. After approximately one hour of charging, the red indicator light should go
“OFF” “ON”
.
ONE HOUR CHARGER #690507
and the green light should come
battery is fully charged.
. The green light indicates that the
Before using battery charger, please read carefully all
instructions and cautionary markings on battery charger, battery pack and
product using battery.
5. When fully charged, reattach battery pack onto Cordless Vacuum, making certain
latches fasten securely. Cordless Vacuum will not operate properly if the battery
pack is not seated properly.
Use only the charger which accompanied your product or direct replacement as
listed in this manual.
approved chargers with your product.
Do not substitute any other charger. Use only Alltrade
OPERATING THE VACUUM
Do not disassemble charger.
This vacuum is for dry pick-up ONLY
. Vacuuming fluids or
combustible material may lead to risk of fire.
Do not use charger if it has been damaged, left outdoors in the rain, snow, wet
or damp environments, or immersed in liquid.
11
12
OPERATING THE ON/OFF SWITCH
MAINTENANCE AND CLEANING
ON OFF
ON/OFF
Push the
switch forward
Always remove the battery pack before attempting clean-
ON
to turn the vacuum
.
ing or maintenance.
ON/OFF
Release the
the vacuum
switch to turn
Do not use paint thinner or any other chemicals to clean the vacuum case.
solvents may damage the plastic. Use only mild soap and water for cleaning.
Harsh
OFF
.
Hold the filter bracket over a trash can to knock loose any debris caught in the
filter.
If the filter is really dirty, wash with warm water and mild soap.
Clean case with a damp cloth.
plastic.
Paper towels and wire brushes may scratch the
CLEANING THE DUST CUP
TO REMOVE THE DUST CUP:
• Hold the vacuum vertically with the handle
pointed up to prevent dust from spilling out.
To prevent risk of electric shock, make sure that all parts are completely dry
before use.
For mechanical problems, consult an authorized technician.
Do not attempt to
• Push on the dust cup release button and pull
the dust cup free.
repair the vacuum yourself.
• Reach inside the dust cup and remove the
filter bracket.
ACCESSORIES
• Clean out the dust cup. If necessary, wash
with mild soap and water.
Use only accessories that are recommended by the manufacturer for your model.
Accessories that may be suitable for one tool may become hazardous when used on
another tool.
• Put the filter back into the top of the dust cup.
Always attach grounded (3-prong) extension cords to grounded (3-hole) outlets.
• Make sure filter and cup are both completely
dry before reattaching the dust cup.
If you must use an extension cord, be sure that the gauge is large enough to carry
• Empty the dust cup after each use.
the amount of current necessary for your power tool.
If not, your tool may experi-
ence a loss of power, excessive voltage drop or overheating. The smaller the gauge
number, the heavier the cord (see table below).
REATTACHING THE DUST CUP
RECOMMENDED SIZES OF EXTENSION CORDS 120 VOLT AC 60 HZ TOOLS
TOOL CURRENT RATING
CONDUCTOR SIZE IN A.W.G
TO ATTACH THE DUST CUP:
Hold down the dust cup release button while
pushing the dust cup back onto the vacuum.
Once the dust cup is properly seated, release
the button and the dust cup will lock into place.
AMPERE
3-6
6-8
8-10
10-12
12-16
16-20
10FT.
18
18
18
16
25FT.
18
18
18
16
50FT.
18
18
18
14
100FT.
18
16
14
14
-
14
12
12
12
12
12
-
13
14
PURPOSES OR ON A JOBSITE
is not covered under this warranty.
SPECIFICATIONS
The date of purchase shall be the date of shipment to the original purchaser, or the
date the original purchaser took possession, custody or control of the product,
whichever occurred first. This warranty shall be null and void if the product or any
component thereof is modified, altered or used for any commercial purpose or on
a jobsite. This warranty does not apply to any other product and/or component
thereof manufactured or distributed by Alltrade, and does not apply to products
and/or components thereof designed, manufactured and/or assembled by others,
SPECIFICATIONS
Voltage
Air Watts
Capacity
Battery Type
19.2V
50W
22 oz (for dry dust)
Ni-Cad
THERE ARE NO WARRANTIES
WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF.
for which Alltrade makes no warranties whatsoever.
PROTECTING THE ENVIRONMENT
BATTERIES
Warranty Performance
Alltrade batteries can be recharged many times. At the end of their useful life,
recycle batteries with due care for our environment.
By purchasing the product, purchaser expressly acknowledges and agrees that their
sole and exclusive remedy under this warranty shall be strictly limited to the repair
or replacement of any covered nonconforming items or parts thereof provided that
any such nonconforming item and/or part is promptly returned to Alltrade’s facility
postage pre-paid and insured (address: ALLTRADE Warranty Claims & Repair,
1431 Via Plata, Long Beach, CA 90810, Attn: Customer Service #1-800-590-3723)
within the applicable warranty period, with a written request by purchaser that
Alltrade repair and/or replace the nonconforming item and/or part. We recommend
that you keep the original product packaging in the event you need to ship the unit.
We suggest the package be insured against loss or in transit damage. When
sending your product include your name, address, phone number, dated proof
of purchase (or copy), and a statement about the nature of problem. Warranty
coverage is conditioned upon purchaser furnishing Alltrade with adequate written
proof that they are the original purchaser and of the original purchase date. Parts
returned, freight prepaid and insured, to Alltrade’s facility (see above address) will
be inspected and, at Alltrade’s option, repaired and/or replaced free of charge if
found to be defective and subject to warranty. Alltrade retains the sole discretion
to determine whether any item or part is nonconforming and, if so, whether the
item and/or part will be repaired and/or replaced. If the unit is repaired, new or
reconditioned replacement parts may be used. If Alltrade chooses to replace
the product, it may replace it with a new or reconditioned one of the same or
comparable design. The repaired or replaced unit will be warranted under the terms
of the remainder of the warranty period. Typically, a defective product that is
returned within the first 30 days after the purchase date will be replaced; for items
returned after the first 30 days and within the warranty period, covered defective
parts not subject to normal wear and tear or other exclusions will be repaired or
replaced, at Alltrade’s option. During the warranty period, Alltrade will be responsi-
ble for the return shipping charges. Alltrade’s repair and/or replacement of any non-
conforming item and/or part thereof shall constitute fulfillment of all
obligations to the purchaser. Alltrade shall not be responsible or liable for any
expense, including freight charges, or repairs made outside Alltrade’s facility, unless
Ni-Cad and Ni-MH batteries are recyclable. Take them to your local recycling center
1-800-822-8837
. Collected batteries will be recycled or disposed of properly.
or call
OTHER CONSUMER DO-IT-YOURSELF (DIY) TOOLS
Alltrade offers a full range of Kawasaki™ tools that make DIY jobs easy. If you would
like further information on the following products, please contact Alltrade Customer
Service Department at 1-800-590-3723.
Cordless Vacuums/Screwdrivers
Reciprocating Saws
Impact Wrenches
Sanders
Routers
Rotary Tools
Jigsaws
Corded and Cordless Multi-Purpose Tools
Wide Range of Accessories and more
Circular Saws
Angle Grinders
2 YEAR LIMITED HOME USE WARRANTY
Express and Exclusive Limited Home Use Warranty to Original Retail Buyer
Alltrade Tools LLC (hereinafter "Alltrade") expressly warrants to the original retail
purchaser of the accompanying KAWASAKI™ portable power tool and no one else
all parts of the product (except those parts referred to below which are specifically
excluded from such warranty (see Exclusions)) to be free from defects in materials
and workmanship for a period of two years from original date of purchase.
SPECIAL WARRANTY NOTE TO CONTRACTORS AND COMMERCIAL USERS:
Kawasaki™ portable power tool is offered as a home use tool and carries a
This
HOME
USE WARRANTY
.
This tool is made for home use in the execution of
COMMERCIAL
projects and repairs in and around the home. Use of the tool for
15
16
expressly agreed to by Alltrade in writing. Under no circumstances shall Alltrade
bear any responsibility for loss of the unit, loss of time or rental, inconvenience,
commercial loss or consequential damages.
EXCLUSION AND DISCLAIMER OF ALL IMPLIED WARRANTIES, INCLUDING THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. NO WARRANTY, ORAL OR WRITTEN, OTHER THAN THE ABOVE
WARRANTY IS MADE WITH REGARD TO THIS PRODUCT. ALL EXPRESS AND/OR
IMPLIED WARRANTIES, GUARANTIES AND/OR REPRESENTATIONS BY ALLTRADE
AND/OR ITS REPRESENTATIVE(S) REGARDING THE DESIGN, MANUFACTURE,
PURCHASE, USE AND/OR OPERATION OF THE PRODUCT OR ANY COMPONENT
THEREOF SOLD HEREUNDER, REGARDLESS OF WHETHER ANY SUCH WARRANTY,
GUARANTY AND/OR REPRESENTATION, WRITTEN OR ORAL, ARISES BY
OPERATION OF LAW AND/OR EQUITY AND/OR BY ANY ACT OR OMISSION OF
ALLTRADE AND/OR ITS REPRESENTATIVE(S), OR THE PURCHASER, INCLUDING
BUT NOT LIMITED TO THE IMPLIED WARRANTY OF MERCHANTABILITY AND THE
WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY EXPRESSLY
EXCLUDED AND DISCLAIMED BY ALLTRADE AND/OR ITS REPRESENTATIVES.
PURCHASER KNOWINGLY AND WILLINGLY WAIVES ANY AND ALL SUCH
WARRANTIES AND RIGHTS, CLAIMS AND/OR CAUSES OF ACTION ARISING
THEREFROM OR BASED THEREON. PURCHASER’S SOLE AND EXCLUSIVE
REMEDY IS AS STATED ABOVE.
Exclusions
This warranty does not cover parts damaged due to normal wear, abnormal
conditions, misapplication, misuse, abuse, accidents, operation at other than
recommended pressures or temperatures, improper storage or freight damage.
Parts damaged or worn by operation in dusty environments are not warranted.
Failure to follow recommended operating and maintenance procedures also
voids warranty.
This limited warranty does not apply to accessory items such as drill bits,
screwdriving bits, circular saw blades, jigsaw blades, grinding wheels, sanding
sheets and other related items.
DAMAGE TO THE PRODUCT RESULTING FROM TAMPERING, ACCIDENT, ABUSE,
NEGLIGENCE, FAILURE TO FOLLOW INSTRUCTIONS, UNAUTHORIZED REPAIRS
OR ALTERATIONS, DAMAGE WHILE IN TRANSIT TO OUR SERVICE FACILITY,
USE OF UNAPPROVED OR IMPROPER ATTACHMENTS OR ACCESSORIES,
COMMERCIAL AND RENTAL APPLICATIONS OR OTHER CAUSES UNRELATED TO
PROBLEMS WITH MATERIAL OR WORKMANSHIP ARE NOT COVERED BY THIS
WARRANTY.
Limitation Of Liability
IN NO EVENT SHALL ALLTRADE AND/OR ITS REPRESENTATIVE(S) BE LIABLE FOR
INDIRECT, INCIDENTAL, SPECIAL AND/OR CONSEQUENTIAL DAMAGES OF ANY
KIND ARISING OUT OF OR RELATED TO, DIRECTLY OR INDIRECTLY, ANY BREACH
OF ANY PROVISION OF ANY AGREEMENT BETWEEN ALLTRADE AND/OR ITS
REPRESENTATIVE(S) AND PURCHASER, ANY WARRANTY HEREUNDER,
AND/OR THE EXISTENCE, DESIGN, MANUFACTURE, PURCHASE, USE AND/OR
OPERATION OF ANY ITEM(S) SOLD HEREUNDER EVEN IF ALLTRADE AND/OR ITS
REPRESENTATIVE(S) HAS BEEN ADVISED OF THE POSSIBILITY OF ANY SUCH
DAMAGES. IN NO EVENT, WHETHER AS A RESULT OF A BREACH OF CONTRACT,
WARRANTY, TORT (INCLUDING NEGLIGENCE) OR OTHERWISE, SHALL
ALLTRADE’S AND/OR ITS REPRESENTATIVE(S)’ LIABILITY EXCEED THE PRICE OF
THE PRODUCT. ANY AND ALL LIABILITY CONNECTED WITH THE USE OF
THIS PRODUCT SHALL TERMINATE UPON THE EXPIRATION OF THE WARRANTY
PERIODS SPECIFIED ABOVE.
Alltrade will not be liable for the following: labor charges, loss or damage resulting
from improper operation, maintenance or repairs made by other persons;
pre-delivery services such as assembly, oil or lubricants, and adjustment;
maintenance services that are normally required to maintain the product.
The use of other than genuine Alltrade Repair Parts will void warranty.
Warranty Disclaimers
EXCLUSION AND DISCLAIMER OF ALL OTHER EXPRESS WARRANTIES,
GUARANTIES AND/OR REPRESENTATIONS. EXCEPT FOR THE LIMITED WARRANTY
PROVIDED ABOVE, ALL OTHER EXPRESS WARRANTIES, GUARANTIES AND/OR
REPRESENTATIONS BY ALLTRADE AND/OR ITS REPRESENTATIVE(S) REGARDING
THE DESIGN, MANUFACTURE, PURCHASE, USE AND/OR OPERATION OF THE
PRODUCT OR ANY COMPONENT THEREOF SOLD HEREUNDER, REGARDLESS OF
WHETHER ANY SUCH WARRANTY, GUARANTY AND/OR REPRESENTATION,
WRITTEN OR ORAL, ARISES BY OPERATION OF LAW AND/OR EQUITY AND/OR BY
ANY ACT OR OMISSION OF ALLTRADE AND/OR ITS REPRESENTATIVE(S), OR THE
BUYER, ARE HEREBY EXPRESSLY EXCLUDED AND DISCLAIMED BY ALLTRADE
AND/OR ITS REPRESENTATIVES. PURCHASER KNOWINGLY AND WILLINGLY
WAIVES ANY AND ALL SUCH WARRANTIES AND RIGHTS, CLAIMS AND/OR
CAUSES OF ACTION ARISING THEREFROM OR BASED THEREON. PURCHASER’S
SOLE AND EXCLUSIVE REMEDY IS AS STATED ABOVE.
Limitations on Warranty Disclaimers
Some states do not allow limitations on how long an implied warranty lasts
and some states do not allow the exclusion or limitation of the incidental or
consequential damages, so part or all of the above limitations or exclusions may not
apply to you. This warranty gives you specific legal rights, and you may also have
other rights which vary from state to state.
If your product is not covered by this warranty, please call our Customer Service
Department toll free at 1-800-590-3723 for general repair information and charges.
17
18
|