Using the KODAK PROFESSIONAL
READYLOAD Single-Sheet Packet
August 2007 • E-2549
TECHNICAL DATA / REFERENCE
KODAK PROFESSIONAL READYLOAD Single-Sheet
Packets and the KODAK PROFESSIONAL READYLOAD
Packet Film Holder provide a very convenient way to
expose 4 x 5-inch sheet film.You can use them together as
a handy alternative to standard 4 x 5-inch sheet-film
holders.
Film Availability
The films packaged in KODAK PROFESSIONAL
READYLOAD Single-Sheet Packets are listed below. Refer
these films.
KODAK Film
CAT No.
834 6926
840 3545
825 4328
894 9281
You’ll have less equipment to carry, because you can use
a single holder to make as many exposures as you need.
The sealed packet also keeps light, fingerprints, and dust
safely away from the film.
Each READYLOAD Single-Sheet Packet contains one
sheet of 4 x 5-inch film, which is attached on both ends to
a leader and trailer. The lighttight outer envelope performs
the same function as a dark slide in a conventional
sheet-film holder.
PROFESSIONAL PORTRA 160VC Film
PROFESSIONAL EKTACHROME E100G
PROFESSIONAL EKTACHROME E100VS
PROFESSIONAL T-MAX 100 / 100TMX
KODAK PROFESSIONAL READYLOAD Packet Film
Holder
This 4 x 5-inch film holder fits any standard press or view
camera, as well as many scientific and recording
instruments. The holder can replace or complement your
standard 4 x 5-inch sheet-film holders.
Use this holder to expose film packaged in KODAK
PROFESSIONAL READYLOAD Single-Sheet Packets. It
offers the following features:
KODAK PROFESSIONAL READYLOAD Single-Sheet
Packets
New READYLOAD Single-Sheet Packets offer these
features:
• One preloaded 4 x 5-inch sheet of film per packet
• Accurate alignment and positioning in the film plane
• Light weight and easy to use
• Great ease and convenience of use—no darkroom or
loading bags required; lighter and less bulky than
standard 4 x 5-inch film holders
• Less time in the dark—no more film holders to load
and unload
• Protection against light leaks, dust, and dirt during use
• Protection against abrasions and fingerprints that can
occur while loading sheet-film holders
• Easy unloading for processing with standard
processing equipment
• Color-coded packet graphics for easy film
identification
• Compatibility with the POLAROID Model 545i Film
Holder
©Eastman Kodak Company, 2007
Operating Tips
Using the KODAK PROFESSIONAL READYLOAD
Single-Sheet Packet in the POLAROID 4 x 5 Film
Holder, Model 545i
• When you insert and remove the packet, grasp the end
of the envelope between your thumb and index finger.
To expose the film, follow these steps:
• When you squeeze and hold the release bar, keep it
fully depressed.
1. Move the control arm to “L.” Grasp the end of the
packet and insert the packet into the holder until it
comes to a firm stop.
• Use a dark cloth when shooting outdoors in bright
sunlight.
• Keep the READYLOAD Packet Film Holder clean.
Press down on the pressure plate and use compressed
air to remove dust and dirt. You can clean the pressure
plate with KODAK PROFESSIONAL Lens Cleaner.
• When you pull the envelope out to expose the film
(Step 2), part of the stop zone will be visible. To verify
that your packet was inserted correctly, feel the
withdrawn packet envelope. You should NOT feel the
thickness of the film. If you feel the film, the packet
was not seated properly. Push the packet back into the
holder until it comes to a firm stop. Then repeat Step 2.
545
• The release bar should only be used when removing
the packet from the holder. If you forget to squeeze
and hold the release bar and force the packet from the
holder, the clip may detach from the packet and stay in
the holder. If this happens, remove the holder from the
camera and depress the pressure plate. Shake the
holder until the clip falls out.
2. Grasp the outer protective envelope as shown, and
pull it out until it stops. You should see part of the
stop zone.
3. Expose the film as you normally do.
4. Push the outer envelope all the way back into the
holder until it comes to a firm stop.
• The foil bag can be reused to store exposed packets.
5. To remove the packet from the holder, squeeze and
hold the release lever (“R”). Leave the control arm at
“L.” Then pull the packet straight out. Do not bend the
packet when you remove it from the holder.
545
6. Wrap an “Exposed” sticker around the end of the
packet with the metal clip.
Using the KODAK PROFESSIONAL READYLOAD Single-Sheet Packet • E-2549
3
Using the KODAK PROFESSIONAL READYLOAD Single-Sheet Packet
5. Process the film as you normally do.
PROCESSING
6. Save the cover envelope if you made notes on it.
To unload the film from the packet for processing, follow
these steps:
Handle exposed film in total darkness. To avoid getting
fingerprints on the film, wear cotton or nylon gloves when
you unload it for processing.
MORE INFORMATION
Kodak has many publications to assist you with
information on Kodak products, equipment, and materials.
Additional information is available on the Kodak website
and through the U.S.A./Canada faxback system.
The following publications are available from Kodak
Customer Service, from dealers who sell Kodak products,
or you can contact Kodak in your country for more
information.
1. Remove or tear the "Exposed" sticker.
2. Grasp both ends of the metal clip with one hand.
Grasp the other end of the packet with your other
hand. Tug gently to unseat the clip from the outer
envelope. Pull the film assembly out of the outer
envelope.
3. Hold the film assembly so that the base side is up.
(The leader and trailer are attached to the base side of
the film.) Peel away the trailer and clip.
E-190
E-163
KODAK PROFESSIONAL PORTRA Films
KODAK PROFESSIONAL EKTACHROME Film E100VS
KODAK PROFESSIONAL T-MAX Films
F-4016
For the latest version of technical support publications for KODAK
PROFESSIONAL Products, visit Kodak on-line at:
If you have questions about KODAK PROFESSIONAL Products,
call Kodak.
In the U.S.A.:
1-800-242-2424, Ext. 19, Monday–Friday
9 a.m.–7 p.m. (Eastern time)
In Canada:
4. Peel the leader away from the film.
1-800-465-6325, Monday–Friday
8 a.m.–5 p.m. (Eastern time)
Note: It is generally easier to peel the leader and trailer
from the film rather than peel the film from the leader/
trailer.
Kodak, Kodak Professional, Ektachrome,
Portra, Readyload, and T-Max are trademarks.
Revised 8-07
Printed in U.S.A.
Using the KODAK PROFESSIONAL
READYLOAD Single-Sheet Packet
KODAK Publication No. E-2549
Film & Photofinishing Systems Group
EASTMAN KODAK COMPANY • ROCHESTER, NY 14650
|