UK
Kompernaß Handelsgesellschaft mbH
Burgstr. 21 • D-44867 Bochum
ID-Nr. KH3460/07-04V2
Ƹ
¹
ƹ
ƺ
ƻ
¸
ᕧ
ᕨ
ᕩ
µ
ᕢ
ᕣ
ᕤ
ᕥ
ᕦ
ᕡ
Ƽ
Professional Meat Grinder
Bifinett KH 3460
Contents
2. Technical Data
GB
1. Intended use .............................. 3
2. Technical data ............................ 3
3. Delivery contents ...................... 3
4. Safety instructions .................... 4
5. Assembly.................................... 5
6. Operation .................................. 7
7. Troubleshooting.......................... 9
8. Cleaning .................................... 9
9. Storage .................................... 10
10. Disposal.................................... 10
11. Warranty and service ................10
Voltage ....................: 230 V / ~50 Hz
Power consumption : 550 W max.
Weight ....................: 4,57 kg approx.
Dimensions (mm) ....: 325x160x317
3. Delivery Contents
ᕡ
ᕢ
ᕣ
ᕤ
ᕥ
Motor block
Meat grinder casing
Transport screw
Cross blade
1. Intended use
This appliance is meant to be usedfor
processing foods in small quantities,
enough for private households.
cutting discs for coarse
and fine grinds
ᕦ
ᕧ
ᕨ
ᕩ
µ
¸
¹
Ƹ
ƹ
ƺ
ƻ
Ƽ
Ring clamp
Feeding tray
•
•
Mincing fresh meat,
Round stodger
Making sausages with natural or
artificial sausage skin,
Sausage disc
•
•
Grating vegetables
Sausage attachment
Kubbe attachment
Grater funnel
Crushing fruit with seeds as well as
seedless fruits.
•
Making shortbread cookies
Square stodger
This appliance is not meant to be
used for processing frozen foods or
other hard foodstuffs, e.g. bones or
nuts. It is not to be used for commer-
cial or industrial purposes.
Coarse grater attachment
Fine grater attachment
Cutter attachment
Shortbread cookies attachment
3
Keep this manual for future reference and pass it on with the device to any future
users!
4. Safety Instructions
4. Safety Instructions
To avoid life-threatening electric
shocks:
To avoid the risk of accidents and
injuries:
•
Make sure that the cable is not
damaged. Protect the cable from
heat and make sure that it does
not get stuck or clamped.
•
Never put your hand into the
openings of the appliance. Do
not insert any objects through
the openings – except for the
appropriate stodger and the food-
stuff to be processed. Otherwise,
there are chances of a serious risk
of accidents!
GB
•
If the cable or the electric plug
is damaged, get it replaced by
customer service, before you con-
tinue using the appliance.
•
•
Unplug the appliance, before
attaching or removing the acces-
sories.
•
•
Use the appliance only in a dry
areas, and not outdoors.
Never immerse the motor in
water or other liquids! You might
suffer from a life-threatening elec-
tric shock.
Do not leave the appliance unsu-
pervised, when it is ready for use.
Always unplug the appliance after
use or during breaks in order to
avoid it from being turned on acci-
dentally.
•
•
Only use original accessories,
which are meant for this appli-
ance. Other parts may probably
not meet the safety requirements.
Warning!
Never use the appliance for any
other purposes other than those
listed here. There is a major possi-
bility of accidents if you mistakenly
happen to turn off the safety device
of the appliance!
Do not allow children and elderly
people to handle the appliance
without supervision, since they
may not always be able to assess
potential hazards.
4
5.
Assembly
5. Assembly
All accessories are coated with a thin
oil film to protect them from corrosion.
Therefore clean all the parts carefully
before using the appliance for the first
time, in accordance with the detailed
instructions found under “8 Cleaning”.
•
The assembled meat grinder is con-
nected by a bayonet joint to the
motor block ᕡ:
GB
- Insert the meat grinder into the
motor block. The arrow on the
mincer casing should be on the
symbol “offen” (open) (Fig. A).
a) Assembling the meat grinder
- Press in the meat grinder lightly.
Turn the stuffing funnel of the
meat grinder upwards till it is ver-
tical (Fig. B).
Unfold the fold out. There you will find
the step-by-step illustrations for
assembling the appliance.
•
•
•
Place the transport screw ᕣ with
the hexagonal axle in the mincer
casing ᕢ.
- To take it out, once again press
down the meat grinder lightly and
turn the stuffing funnel in the
direction of the symbol ”offen“
(Fig. A). Now you can pull out the
meat grinder.
Ensure that the metal washer
remains on the hexagonal axle.
Without the washer, the screw
would close too fast.
•
Finally place the feed tray ᕧ on
top on the stuffing funnel.
Now place the cross blade ᕤ so
that the sharp side is facing the
cutting disc ᕥ. Warning - the
blade is very sharp!
b) Fixing the sausage stuffer
attachment
Attention: the device can get dam-
aged if the cross blade is wrongly
inserted in the opposite direction!
Once the meat grinder has been
assembled as described under a):
•
•
Turn open the ring clamp ᕦ and ...
Choose the appropriate cutting
disc – You can find the discs in the
small recess at the top of the
device (Fig. D).
Replace the cutting disc ᕥ with
the sausage disc ᕩ. This can be
found in the small recess (Fig. D)
on the top of the device. Fix this in
as described in a).
For this push the cover upwards
and take out the required disc.
•
•
Now place the sausage stuffer
attachment µ in front of the
sausage disc, ...
•
•
Insert both the edges of the chosen
disc ᕥ into the slots in the mincer
casing ᕢ.
before screwing on the ring clamp
ᕦ tightly.
After everything has been assem-
bled correctly, screw on the ring
clamp ᕦ tightly.
5
c) Fixing the kubbe attachment
Once the meat grinder has been
assembled as described under a):
•
To remove once again press in the
grater funnel lightly and turn it in
the direction of the symbol "open“
(Fig. A). Now you can take out the
grater funnel.
•
Turn open the ring clamp ᕦ and ...
GB
•
Replace the cutting disc ᕥ with the
two plastic parts of the kubbe
attachment ¸. Fix these as
described in a).
e) Fixing the shortbread cookie
attachments
•
When everything has been
attached correctly, screw on the
ring clamp ᕦ tightly.
Once the meat grinder has been
assembled as described under a):
•
•
Turn open the ring clamp ᕦ and ...
d) Fixing the grater and cutter
attachments
take out the cutting disc ᕥ and the
cross blade ᕤ.
When the meat grinder has been
removed from the motor block:
•
•
Remove the pattern strips from the
shortbread cookie attachment Ƽ
and ...
•
First select the appropriate attach-
ment. You can choose from...
place the shortbread cookie
attachment in the mincer casing
¹.
- a coarse grater ƹ,
- a fine grater ƺ,
Insert both the edges of the short-
bread cookie attachment Ƽ into
the slots in the mincer casing ¹.
- a cutter attachment ƻ.
•
•
Fix the grater or cutter attachment
in the provided round recesses in
the grater funnel. ¹.
•
•
When everything has been
attached correctly, screw on the
ring clamp tightly ᕦ and ...
Place the grater funnel in the motor
block in such a way that the arrow
of the grater funnel points to the
symbol ”open“.
once again attach the pattern
strips to the front part of the short-
bread cookie attachment.
Press in the grater funnel lightly
and turn it upwards till it is in a ver-
tical position.
•
To remove you must again remove
the pattern strip first, before turn-
ing open the ring clamp ᕦ and
taking out the shortbread cookie
attachment Ƽ.
6
6. Operation
6. Operation
Attention: In the case of foods, which
need to be processed at high speeds,
the appliance should not be run for
longer than 10 seconds (!) at a
•
First press the OFF button, to
ensure that the appliance is off.
Then plug in...
GB
stretch. Let there be a break of 30
seconds before switching it on again,
to prevent the motor from overheating.
and set it to ON , to switch it on.
•
Now push in the food with the
round ᕨ or square stodger Ƹ in
the feeding tube - never with one’s
fingers, forks, spoons or similar
objects. This could lead to injury
and also damage the appliance.
One can tell that the machine is being
overused when the sound of the motor
changes and slows down.
a) Operating the appliance
Once the appropriate attachments
have been fixed:
Attention: Do not ever press so
hard that the motor gets audibly
slower. This could put the machine
under pressure and damage it.
•
Place the appliance in such a way
that it is absolutely stable and
cannot fall off the table or into
water (due to vibrations or if it gets
caught in the cable). . The machine
will inevitably vibrate when it is run-
ning.
b) Processing meat
•
•
•
Only use meat pieces, which are
not larger than 2 cm. Check that
the meat does not have any bones
and is not stringy.
Warning: Never touch a machine,
which is plugged in or is operational
when it happens to fall or land in
water – or in the case of other
emergencies!
Caution: Mincemeat is prone to
decay. Therefore take care to main-
tain good hygiene when processing
meat.
First unplug the appliance in all
emergency situations! Otherwise
one runs the risk of serious injury or
loss of life!
When you have read all the instruc-
tions on the topic ”Meat“, you can
use the appliance as described
under 6.a).
•
Place the food, which is to be
processed in the feeding tray ᕧ and
place a vessel to collect the
processed food in front under the
opening.
7
c) Processing sausage meat
d) Grating and cutting
•
Put the meat through the meat
grinder twice before using it as
sausage stuffing.
After you have placed the food to be
grated into the feeding trayᕧ:
•
•
Push them with the square stodger
Ƹ into the feeding tube ¹.
GB
•
To make the sausage stuffing, add
some chopped onions, spices and
other ingredients to the mincemeat
as per your recipe, and knead the
mixture. Refrigerate this for 30 min-
utes before processing it further.
If some food is stuck on the grating
attachments: Switch off the
device before removing the
attachments or reaching in to
clean them. Otherwise there is the
risk of getting injured.
•
Put the sausage skin (natural or
artificial sausage skin) on the
sausage stuffer attachment10 and
knot up the other end. For 1 kg of
the filling, you will need approxi-
mately 1.60 m of sausage skin.
•
After you have read all the instruc-
tions about the topic “Grating and
cutting“, you can use the machine
as described under 6 a).
Tip: Soak the natural sausage skin
in lukewarm water for about 3
hours before using it and then
wring out. Natural sausage skin will
thus get more elastic.
e) Using the kubbe attachment
With the kubbe attachment foodstuffs
can be processed to form hollow rolls
of meat or vegetables, which can then
be stuffed as desired.
•
Put the meat through the meat
grinder twice before pressing it
through the kubbe attachment.
•
The sausage mixture will be
pressed into the sausage skin by
the sausage stuffer. When it is long
enough switch off the device and
press together the sausage at the
end and turn it around its longitudi-
nal axis.
•
After you have read all the instruc-
tions about the topic “Kubbe
attachment“, you can use the
machine as described under 6 a).
Tip: Sausage meat tends to
expand when cooked or frozen.
Therefore it is best not to overstuff
the sausage to prevent it from
splitting.
f) Making shortbread cookies
After you have made the shortbread
dough according to your recipe, and
after having fixed the shortbread cookie
attachment:
•
After you have read all the instruc-
tions about the topic “Sausage“,
you can use the machine as
described under 6 a).
•
Line a small baking tray with
greaseproof paper and place or
hold it directly under the opening in
the front of the appliance.
8
•
•
In case this does not work, wait for
a further 15 minutes.
•
•
Press dough evenly into the feed-
ing tube – the transport screw
pushes it through the design on the
pattern strip of the shortbread
cookie attachment Ƽ.
If it still does not function at the
end of this period, this indicates a
technical problem. In this case,
contact the service centre.
GB
After you have read all the instruc-
tions about the topic ”shortbread
cookie attachment“, you can use the
appliance as described under 6 a).
If themains cable is damaged or or
the accessories are visibly damaged:
•
•
•
Switch off the device by pressing
the OFF button!
if this is not safely possible unplug
the appliance.
Warning:
Never open the casing of the
motor block– There are no operat-
ing parts to be found there. If the
casing is opened there exists the
possibility of a life-threatening
electric shock.
Get the parts be repaired by cus-
tomer service, before reusing the
appliance again.
8. Cleaning
Pull out the plug from the socket,
before cleaning the appliance.
In this way accidents caused by the
unexpected switching on of the
machine and electric shocks can be
prevented.
7. Troubleshooting
If the smooth running of the appliance
is hampered by excessive or stuck
food:
•
Keep the REV key pressed. The
machine will now run in the reverse
direction. This will enable you to
dislodge the food, which has got
stuck, and the machine will once
again run smoothly.
a) Cleaning the Motor block
•
Clean the external surfaces and
the power cord with a slightly
damp cloth. Always dry the device
well before using it again.
•
If you do not succeed by doing so,
clean the machine as described
under 8.
•
Warning: Never immerse the motor
block in water or any other liquid!
Otherwise one could get a life
threatening electric shock, if mois-
ture, which has crept in, touches
the electrical wiring.
If the motor stops suddenly, it could
be due to the internal overload warn-
ing device, which automatically turns
off the machine when overloaded. This
is supposed to protect the motor.
•
Switch off the device and let it cool
down for approximately 15 minutes
before using it again.
9
•
Never use any cleansers, abrasive
substances or solvents. These
could damage the device.
•
Keep the machine away from chil-
dren and elderly people. They may
not always be able to assess
potential dangers of the heating
elements of such devices.
GB
b) Cleaning accessories
•
Wash all the accessories that can
come in contact with food, ...
10. Disposal
- by hand only, the accessories
are not dishwasher safe.
Tip: Care for the environment.
If you wish to dispose of the device,
dispose of it at a collection site for
recycling of electronics.
- with hot water and a household
cleaning liquid suitable for food-
stuff surfaces
Make the appliance unusable by
removing the plug before disposing of
the appliance, in order to prevent acci-
dents caused by children playing with
the appliance.
•
•
Caution: The cross blade and the
shredder attachments are very
sharp!
Dry all parts thoroughly, before
reusing the appliance.
Ensure that sharp parts (cross blade,
shredder attachments) are removed to
protect children.
9. Storage
•
Wind the mains cable under the
bottom part of the appliance. In
this way, it is protected from dam-
age.
11. Warranty and service
The warranty conditions and service
centre address can be found in the
enclosed warranty slip.
•
Store the discs in the small recess
(Fig. D) on top of the machine.
•
•
Store the appliance in a dry place.
After drying the metal attachments
rub them lightly with a little cooking
oil, if you are not going to use the
device immediately. This will pro-
tect them from corrosion.
10
|