User Manual
( )
Network Interface Card NC-6
Contents
1
Welcome
1.1
1.2
2
Getting Ready
2.1
For Windows NT 4.0...................................................................2-3
For Windows 2000......................................................................2-4
Supported Environments............................................................2-6
2.2
LPR / PORT 9100 Printing .........................................................2-8
NetWare Server/Client (except NDPS).....................................2-10
3
4
Checking the Accessories
3.1
Accessories...................................................................................3-1
Connecting the Network Cable
4.1
4.2
5
Assigning an IP Address
5.1
5.2
Entering the IP Address From the Control Panel.......................5-1
Assigning an IP Address..............................................................5-2
6
7
Printing the Configuration Page
Connecting the Computer and Copier
7.1
Procedures Described in This Chapter.......................................7-1
NC-6
i
7.2
7.2.1
7.2.2
7.2.3
7.2.4
Printing to Port 9100 .................................................................. 7-6
Windows 2000/ Windows XP..................................................... 7-6
Windows 2000/ Windows XP..................................................... 7-7
Check the IPP Settings Using PageScope Light ....................... 7-7
7.2.5
Setting Up NetWare 4.x/ 5.x/ 6 Remote Printer Mode ............. 7-10
Setting Up the Windows Computer for the NetWare Client ..... 7-13
8
8.1
8.2
8.3
8.4
8.5
8.6
What is PageScope Light? .......................................................... 8-1
About the Screen Layout............................................................. 8-4
Logging In as an Administrator .................................................. 8-5
Logging In to Administrator Mode.............................................. 8-5
8.7
About the File Download Function ............................................. 8-5
Types of File That Can Be Downloaded .................................... 8-5
9
Appendix
9.1
9.2
Product Specifications................................................................. 9-1
Troubleshooting ........................................................................... 9-2
ii
NC-6
User Instructions
For the U.S.A.
FCC Part 15-Radio Frequency Devices
NOTE
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and radiates radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in
which case the user will be required to correct the interference at his own expense.
WARNING
The design and production of this unit conform to FCC regulations, and any changes or
modifications must be registered with the FCC and are subject to FCC control. Any changes
made by purchaser or user without first contacting the manufacturer will be subject to penalty
under FCC regulations.
This device must be used with shielded interface cables. The use of non-shielded cables is
likely to result in interference with radio communications and is prohibited under FCC rules.
For Canada
Interference-Causing Equipment Standard (ICES-003 Issue 3)
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
For Europe
CE Marking (Declaration of Conformity)
This product complies with the following EU directives:
89/336/EEC, 73/23/EEC and 93/68/EEC directives.
This declaration is valid for the area of the European Union.
This device must be used with shielded interface cables. The use of non-shielded cables is
likely to result in interference with radio communications and is prohibited under EU
directives.
NC-6
iii
For countries subject to Class B regulations
This device must be used with shielded interface cables. The use of non-shielded cables is
likely to result in interference with radio communications and is prohibited under CISPR 22
rules and local rules.
For countries not subject to Class B regulations
WARNING
This is a Class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
This device must be used with shielded interface cables. The use of non-shielded cables is
likely to result in interference with radio communications and is prohibited under CISPR 22
rules and local rules.
iv
NC-6
Welcome
1
1
Welcome
This manual provides information on setting up and using a copier as a
network printer.
Read these instructions thoroughly before using the functions.
For instructions on using the copier itself and for general safety
precautions, refer to the manual provided with the copier.
Store this manual and the enclosed CD-ROM in a safe location for future
reference.
Note
No part of this manual may be copied or reproduced, either in part or
in whole, without prior permission.
The contents of this manual are subject to change without notice.
No part of the manual may be reproduced or modified without prior
permission.
Screen images used in this manual may differ from the actual screen
display.
NC-6
1-1
Welcome
1
1.1
Trademark Acknowledgements
PageScope is trademark of KONICA MINOLTA BUSINESS
TECHNOLOGIES, INC.
Ethernet is a registered trademark of Xerox Corporation.
PCL is a registered trademark of Hewlett-Packard Company.
Microsoft, Windows, and Windows NT are registered trademarks of
Microsoft Corporation.
Netscape Communications, the Netscape Communications logo,
Netscape Navigator, Netscape Communicator, and Netscape are
trademarks of Netscape Communications Corporation.
Novell and NetWare are registered trademarks of Novell, Inc.
All other product names are trademarks or registered trademarks of their
respective holders.
Copyright 2003 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC.
1.2
About PageScope Light
If a network interface card (NIC) is installed, you can use the PageScope
Light network utility. PageScope Light is a network utility that allows you
to modify network and other settings over the network instead of from the
device itself.
All you need in order to use PageScope Light is a Web browser (Internet
Explorer or Netscape Navigator) installed on your computer. It is not
necessary for any special software to be installed. For instructions on
using PageScope Light, refer to “8 Using PageScope Light”.
1-2
NC-6
Getting Ready
2
2
Getting Ready
This manual provides detailed information on using a copier as a network
printer. However, not all information provided will be required by all users.
This chapter is designed to make it easier to find the information and
procedures required for your setup.
1 First, select the most suitable network printing method for your
system. (“Selecting the Network Print Method” on page 2-2)
2 Next, check the procedures required to perform network printing
operations that meet your needs. (“Checking the Setup Procedures”
on page 2-7)
NC-6
2-1
Getting Ready
2
2.1
Selecting the Network Print Method
Once a network card has been installed, various methods for network
printing become available. This section describes how to select the
appropriate network print method for the type of operating system that you
are using.
For Windows 95 (OSR 2.5)/ Windows 98/ Windows 98 SE/ Windows
ME
I Peer-to-Peer
I Network Setup Utility
TCP/IP protocol
Windows 95 (OSR2.5)
Windows 98
Windows 98 SE
Windows ME
Peer-to-Peer Printing
G
G
G
Using the Peer-to-Peer Utility, you can connect a copier and computer
to the same network.
The Peer-to-Peer Utility is automatically installed when you install the
printer driver.
The TCP/IP protocol is used.
Network Setup Printing
G
Using the Network Setup utility, you can connect a copier and
computer to the same network.
G
G
The Network Setup utility is included on the PageScope CD provided.
The TCP/IP protocol is used.
Note
For instructions on using the Network Setup utility to set up network
printing, refer to the manual included on the PageScope CD.
2-2
NC-6
Getting Ready
2
For Windows 2000
I LPR
I IPP
I PORT9100
TCP/IP protocol
Windows 2000
LPR Printing
G
You can connect a copier and computer via the LPR Print Service.
G
The LPR Print Service is available with a standard installation of the
operating system.
G
The TCP/IP protocol is used.
IPP Printing
G
You can connect a copier and computer via the IPP Print Service.
G
The IPP Print Service is available with a standard installation of the
operating system.
G
HTTP (Hyper Text Transfer Protocol), which is part of the TCP/IP
protocol is used. Businesses and organizations may have a firewall
set up to prevent unauthorized access, however, it should normally be
possible to traverse an HTTP firewall. This allows you to print to
network printers beyond the firewall via an IPP connection.
Printing to Port 9100
G
G
G
You can connect a copier and computer via the Port 9100 Print
Service.
The Port 9100 Print Service is available with a standard installation of
the operating system.
The TCP/IP protocol is used.
2-4
NC-6
Getting Ready
For Windows XP
2
I IPP
I PORT9100
TCP/IP protocol
Windows XP
IPP Printing
G
You can connect a copier and computer via the IPP Print Service.
G
The IPP Print Service is available with a standard installation of the
operating system.
G
HTTP (Hyper Text Transfer Protocol), which is part of the TCP/IP
protocol is used. Businesses and organizations may have a firewall
set up to prevent unauthorized access, however, it should normally be
possible to traverse an HTTP firewall. This allows you to print to
network printers beyond the firewall via an IPP connection.
Printing to Port 9100
G
G
G
You can connect a copier and computer via the Port 9100 Print
Service.
The Port 9100 Print Service is available with a standard installation of
the operating system.
The TCP/IP protocol is used.
NC-6
2-5
Getting Ready
2
For NetWare (NetWare Server/ Windows Client)
When using NetWare, you can use a computer running Windows as a
NetWare client to print to a copier via a NetWare server.
NetWare server
TCP/IP protocol or
IPX/SPX protocol
NetWare client PC
(Windows computer)
Supported Environments
The controller supports the system environments described below.
NetWare version
NetWare 4.x
Protocol
IPX
Emulation
Service mode
NDS/Bindery
NDS/Bindery
PServer / NPrinter
PServer / NPrinter
NDPS (lpr)
NetWare 5.x/6
IPX
TCP/IP
2-6
NC-6
Getting Ready
2
2.2
Checking the Setup Procedures
printing for the selected network print method.
Peer-to-Peer Printing
1 Check that all of the accessories have been included in the package.
(“3 Checking the Accessories”)
2 Connect the network cable. (“4 Connecting the Network Cable”)
3 Specify the IP address, subnet mask, and default gateway settings for
the copier. (“5 Assigning an IP Address”)
4 Print the Configuration Page and check the settings. (“6 Printing the
Configuration Page”)
Note
equipped with the optional PCL printer controller or fax option.
5 Install the printer driver. The Peer-to-Peer Utility is installed when you
install the printer driver.
❍
For instructions on installing the GDI driver, refer to “GDI Printer
Controller” in the manual provided with the copier. For instructions
on installing the optional PCL driver, refer to “PCL Printer
Controller” in the manual provided with the PCL printer controller.
6 Add a network port to the computer. (“7 Connecting the Computer and
Copier”)
NC-6
2-7
Getting Ready
2
LPR / PORT 9100 Printing
1 Check that all of the accessories have been included in the package.
(“3 Checking the Accessories”)
2 Connect the network cable. (“4 Connecting the Network Cable”)
3 Specify the IP address, subnet mask, and default gateway settings for
the copier. (“5 Assigning an IP Address”)
4 Print the Configuration Page and check the settings. (“6 Printing the
Configuration Page”)
Note
The Configuration Page cannot be printed for copiers that are not
equipped with the optional PCL printer controller or fax option.
5 Install the printer driver.
❍
For instructions on installing the GDI driver, refer to “GDI Printer
Controller” in the manual provided with the copier. For instructions
on installing the optional PCL driver, refer to “PCL Printer
Controller” in the manual provided with the PCL printer controller.
6 Add a network port to the computer. (“7 Connecting the Computer and
Copier”)
2-8
NC-6
Getting Ready
IPP Printing
2
1 Check that all of the accessories have been included in the package.
(“3 Checking the Accessories”)
2 Connect the network cable. (“4 Connecting the Network Cable”)
3 Specify the IP address, subnet mask, and default gateway settings for
the copier. (“5 Assigning an IP Address”)
4 Print the Configuration Page and check the settings. (“6 Printing the
Configuration Page”)
Note
The Configuration Page cannot be printed for copiers that are not
equipped with the fax function.
5 Install the printer driver. Add a network port during the installation of
the printer driver.
❍
For instructions on installing the GDI driver, refer to “GDI Printer
Controller” in the manual provided with the copier. For instructions
on installing the optional PCL driver, refer to “PCL Printer
Controller” in the manual provided with the PCL printer controller.
For details on specifying the network port, refer to “7 Connecting
the Computer and Copier”.
NC-6
2-9
Getting Ready
2
NetWare Server/Client (except NDPS)
1 Check that all of the accessories have been included in the package.
(“3 Checking the Accessories”)
server. (“7 Connecting the Computer and Copier”)
(“7 Connecting the Computer and Copier”)
NetWare Server/Client (NDPS)
1 Check that all of the accessories have been included in the package.
(“3 Checking the Accessories”)
2 Connect the network cable. (“4 Connecting the Network Cable”)
3 Specify the IP address, subnet mask, and default gateway settings.
(“5 Assigning an IP Address”)
4 Print the Configuration Page and check the settings. (“6 Printing the
Configuration Page”)
Note
The Configuration Page cannot be printed for copiers that are not
equipped with the fax function.
5 Specify the settings that enable the copier to connect to the NetWare
server. (“7 Connecting the Computer and Copier”)
6 Set up the NetWare client so that it can print via the NetWare server.
(“7 Connecting the Computer and Copier”)
2-10
NC-6
Checking the Accessories
3
3
Checking the Accessories
Check that all of the accessories listed below are included in the package.
If any item is missing, contact your service representative.
3.1
Accessories
G
PageScope CD (Includes the network utility software)
G
This manual: User Manual for the Network Interface Card (NC-6)
NC-6
3-1
Checking the Accessories
3
3-2
NC-6
Connecting the Network Cable
4
4
Connecting the Network Cable
Connect the network cable to the copier.
4.1
4.2
Types of Cable That Can Be Used
Use a Category 5 or 5E network cable.
Connecting the Network Cable
Insert the connectors on the network cable into the network ports.
1 Insert the connector on one end of the network cable into the network
port as shown in the illustration.
2 Insert the connector on the other end of the network cable into an
available port on the network hub.
LED1
LED2
About the LEDs
LED1 (LINK):
This LED lights up when the network cable is
connected correctly. If this LED is not lit, check
the connection again, even if the copier appears
to be connected correctly. If this LED is not lit
when both ends are connected correctly, the
network cable may be damaged.
LED2 (ACT):
This LED blinks when data is being transferred.
NC-6
4-1
Connecting the Network Cable
4
4-2
NC-6
Assigning an IP Address
5
5
Assigning an IP Address
From the control panel of the copier, assign an IP address to the copier.
Note
Always assign an IP address only after consulting your network
administrator.
5.1
Entering the IP Address From the Control Panel
Use the 10-key pad on the control panel to enter the IP address.
(Example) To enter “192.168.0.10”
Note
If an element of the number is less than three digits, press the
key
to move the cursor into the area to the right of the current element.
NC-6
5-1
Assigning an IP Address
5
5.2
Assigning an IP Address
The IP address can be assigned using a function on the “NETWORK
SETTING” menu. Other functions on the “NETWORK SETTING” menu
can be used to specify the subnet mask and default gateway settings.
1 Press the [Utility] key.
The first Utility mode screen
appears.
2 Use the
and
keys to select
“NETWORK SETTING?”.
3 Press the [1] key from the 10-key
pad to select “IP ADDRESS”.
4 Use the
and
keys to select
“SPECIFY”, and press the [Yes]
key.
Note
If “SPECIFY” is selected in this step, “AUTO” can also be selected.
If “AUTO” is selected, the IP address, subnet mask, and default
gateway setting are automatically assigned by the DHCP server on
the network. This means that they do not have to be assigned
manually, as is the case when “SPECIFY” is selected. However,
please note the following points when using “AUTO” to assign the
IP address.
5-2
NC-6
Assigning an IP Address
Check with your network administrator to determine if there is a
5
DHCP server available on the network. (If there is, a special IP
address will be assigned by the AutoIP function. However, the
copier will not be able to communicate with other devices on the
network that have had ordinary IP addresses assigned to them.
For details about the AutoIP function, refer to “Product
Specifications” on page 9-1.) Always select “SPECIFY” when
there is no DHCP server available.
When “AUTO” is selected to assign the IP address, the IP address
may sometimes be changed automatically. If the IP address and
other settings are changed, you may not be able to print to a
specified printer on the network due to a communication failure
caused by a change in the address. When “AUTO” is selected, we
recommend that you set the DHCP server to assign a fixed
address to the copier.
5 Use the 10-key pad and
the and keys to enter the IP
address.
Note
If an IP address is already entered, it can be overwritten by a new
one.
The IP address shown in the illustration is only an example. Always
check with your network administrator before entering an IP
address for the printer.
6 Press the [Yes] key to confirm the setting. The “NETWORK SETTING”
menu appears again.
❍
Proceed to enter the subnet mask setting.
7 While the “NETWORK SETTING”
menu is displayed, press the [2] key
in the 10-key pad to select “SUB-
NET MASK”.
NC-6
5-3
Assigning an IP Address
5
8 Use the 10-key pad and
the and keys to enter the
subnet mask address.
Note
The subnet mask address shown in the illustration is only an
example. Always check with your network administrator before
entering a subnet mask address.
9 Press the [Yes] key to confirm the setting. The “NETWORK SETTING”
menu appears again.
❍
Proceed to enter the default gateway setting.
10 While the “NETWORK SETTING”
menu is displayed, press the [3] key
on the 10-key pad to select
“GATEWAY”.
11 Use the 10-key pad and
the
and
keys to enter the
default gateway address.
Note
The default gateway address shown in the illustration is only an
example. Always check with your network administrator before
entering a default gateway address.
12 Press the [Yes] key to confirm the setting.
❍
The “NETWORK SETTING” menu appears again. Finally, the
specified IP address, network mask, and default gateway settings
are registered on the copier itself. In order to register these
settings, the copier must be restarted by turning it off, then on
again.
13 While the “NETWORK SETTING” menu is displayed, press the [No]
key or the [Panel Reset] key to select “PLEASE RE-START POWER
SUPPLY OFF/ON”.
14 Set the power switch on the copier to “O”, then “I” to restart the copier.
5-4
NC-6
Printing the Configuration Page
6
6
Printing the Configuration Page
Detailed information on the settings can be printed so that the contents of
the settings can be easily checked.
Note
The Configuration Page cannot be printed for copiers that are not
equipped with the optional PCL printer controller or fax option.
1 Press the [Status] key on the control
panel of the copier.
2 Use the
3 Press the [Yes] key.
A list of the types of report that can be printed appears.
and
keys to select “PRINTER REPORT?”.
4 Use the
and
keys to select “CONFIGURATION PAGE?”.
5 Press the [Yes] key.
The contents of the settings are printed.
NC-6
6-1
Printing the Configuration Page
6
6-2
NC-6
Connecting the Computer and Copier
7
7
Connecting the Computer and Copier
This chapter describes how to connect the computer and copier, and the
settings required to enable the copier to print jobs received over the
network.
7.1
Procedures Described in This Chapter
The connection procedures described in this chapter are as follows:
G
G
Peer-to-Peer Printing
Windows 95 (OSR 2.5)/ Windows 98/ Windows 98 SE/ Windows ME
LPR Printing
Windows 2000
Windows NT 4.0
G
G
G
Printing to Port 9100
Windows 2000/ Windows XP
IPP Printing
Windows 2000/ Windows XP
Connecting a Copier to the NetWare Server
Setting up NetWare 4.x / 5.x / 6 Print Server Mode
Setting up NetWare 4.x / 5.x / 6 Remote Printer Mode
Setting up NetWare 5.x / 6 Novell Distributed Print Service (NDPS)
Setting up the Windows Computer for the NetWare Client
NC-6
7-1
Connecting the Computer and Copier
7
7.2
Setting Up the Network Connections
7.2.1 Peer-to-Peer Printing
Windows 95 (OSR 2.5)/ Windows 98/ Windows 98 SE/ Windows ME
Important
Before continuing to set up the network settings, check the following:
Check that the computer is set up to use the TCP/IP protocol.
Check that the copier is also set up to use the TCP/IP protocol.
Check that the printer driver has been installed on the computer.
(For instructions on installing the GDI driver, refer to “GDI Printer
Controller” in the manual provided with the copier. For instructions on
installing the optional PCL driver, refer to “PCL Printer Controller” in
the manual provided with the PCL printer controller.)
1 Click [Start] - [Settings] - [Printers] to open the “Printers” folder.
2 Right-click the icon for the installed printer driver.
3 Click [Properties] to open the Properties dialog box.
4 Click the “Details” tab, and then click [Add Port].
5 Select Other.
6 Select Peer2Peer from the list of port types.
7 Click [OK].
8 Enter the copier IP address.
9 Click [OK].
7-2
NC-6
Connecting the Computer and Copier
7
7.2.2 LPR Printing
Windows 2000
Important
Before continuing to set up the network settings, check the following:
Check that the computer is set up to use the TCP/IP protocol.
Check that the copier is also set up to use the TCP/IP protocol.
Check that the printer driver has been installed on the computer.
(For instructions on installing the GDI driver, refer to “GDI Printer
Controller” in the manual provided with the copier. For instructions on
installing the optional PCL driver, refer to “PCL Printer Controller” in
the manual provided with the PCL printer controller.)
1 Click [Start] - [Settings] - [Printers] to open the “Printers” folder.
2 Right-click the icon for the installed printer driver.
3 Click [Properties] to open the Properties dialog box.
4 Click the “Ports” tab, and then click [Add Port].
5 In the Printer Ports dialog box, select Standard TCP/IP Port, and then
click [New Port].
6 When the Add Standard TCP/IP Printer Port Wizard appears, click
[Next>].
7 Enter the IP address for the copier into the Printer Name or IP
Address box, and then click [Next>].
8 Select Custom, and then click [Settings].
9 Select LPR in the Protocol group box, enter the name of the print
queue in the Queue Name box (for example, “print”), and then click
[OK].
Note
Use half-pitch characters to enter the queue name.
NC-6
7-3
Connecting the Computer and Copier
7
10 Click [Next>].
11 Click [Finish].
7-4
NC-6
Connecting the Computer and Copier
7
Windows NT 4.0
Important
Before continuing to set up the network settings, check the following:
Check that the computer is set up to use the TCP/IP protocol.
Check that the copier is also set up to use the TCP/IP protocol.
Check that the printer driver has been installed on the computer.
(For instructions on installing the GDI driver, refer to “GDI Printer
Controller” in the manual provided with the copier. For instructions on
installing the optional PCL driver, refer to “PCL Printer Controller” in
the manual provided with the PCL printer controller.)
Installing the Microsoft TCP/IP Printing Service
1 Click [Start] - [Settings] - [Control Panel] to open the “Control Panel”
folder.
2 Double-click “Network”.
3 Click the “Services” tab, click [Add], and then install the “Microsoft
TCP/IP print service”.
Setting Up the LPR Connection
1 Click [Start] - [Settings] - [Printers] to open the “Printers” folder.
2 Right-click the icon for the installed printer driver.
3 Click [Properties] to open the Properties dialog box.
4 Click the “Ports” tab, and then click [Add Port].
5 In the Printer Port dialog box, select LPR Port, and then click [New
Port].
Note
If “LPR Port” does not appear, install the Microsoft TCP/IP print
service.
NC-6
7-5
Connecting the Computer and Copier
7
6 After the Add LPR Compatible Printer dialog box appears, enter the
copier IP address in the Name or address of server providing lpd
services box, and then click [OK].
Enter the name of the print queue in the Name of printer or print
queue on that server box. (Example: print)
7 Follow the instructions that appear on the screen to complete the
installation for an LPR-compatible printer.
7.2.3 Printing to Port 9100
Windows 2000/ Windows XP
Important
Before continuing to set up the network settings, check the following:
Check that the computer is set up to use the TCP/IP protocol.
Check that the copier is also set up to use the TCP/IP protocol.
Check that the printer driver has been installed on the computer.
(For instructions on installing the GDI driver, refer to “GDI Printer
Controller” in the manual provided with the copier. For instructions on
installing the optional PCL driver, refer to “PCL Printer Controller” in
the manual provided with the PCL printer controller.)
1 When using Windows 2000, click [Start] - [Settings] - [Printers] to open
the “Printers” folder.
When using Windows XP, click [Start] - [Control Panel] - [Printers and
Other Hardware] - [See a list of installed printers and fax printers.] to
open the “Printers and Faxes” folder.
2 Right-click the icon for the installed printer driver.
3 Click [Properties] to open the Properties dialog box.
4 Click the “Ports” tab, and then click [Add Port].
5 In the Printer Ports dialog box, select Standard TCP/IP Port, and then
click [New Port].
6 When the Add Standard TCP/IP Printer Port Wizard appears, click
[Next>].
7-6
NC-6
Connecting the Computer and Copier
7
7 Enter the IP address for the copier into the Printer Name or IP
Address box, and then click [Next>].
8 Select Custom, and then click [Settings].
9 Select RAW as the protocol.
10 Enter “9100” for the Port Number setting, and then click [OK].
11 Click [Next>].
12 Click [Finish].
7.2.4 IPP Printing
Windows 2000/ Windows XP
Important
Before continuing to set up the network settings, check the following:
Check that the computer is set up to use the TCP/IP protocol.
Check that the copier is also set up to use the TCP/IP protocol.
Check the IPP Settings Using PageScope Light
Use PageScope Light to access the copier and check if IPP printing is
enabled. For instructions on using PageScope Light, refer to “8 Using
PageScope Light”.
1 Start up PageScope Light.
2 Log in to the Administrator mode.
3 Click the “Network” tab, and then select “IPP Configuration” in the
menu.
4 Check that Enable IPP is selected. If it is not selected, IPP printing is
not possible.
NC-6
7-7
Connecting the Computer and Copier
Setting Up the IPP Print Connection
7
Set up the IPP Print connection. In order to set up IPP printing, you must
start by installing the printer driver. (For instructions on installing the GDI
driver, refer to “GDI Printer Controller” in the manual provided with the
copier. For instructions on installing the optional PCL driver, refer to “PCL
Printer Controller” in the manual provided with the PCL printer controller.)
1 When using Windows 2000, click [Start] - [Settings] - [Printers] to open
the “Printers” folder.
When using Windows XP, click [Start] - [Control Panel] - [Printers and
Other Hardware] - [See a list of installed printers and fax printers.] to
open the “Printers and Faxes” folder.
2 Start up the Add Printer Wizard, and then click [Next>].
3 Select Network Printer, and then click [Next>].
4 Select Connect to a printer on the Internet or on your intranet.
❍
(Example) If the copier IP address is 192.168.0.10, enter:
6 Click [Next>]. When a confirmation message appears, click [OK].
7 Follow the instructions that appear on the screen to complete the
installation.
7-8
NC-6
Connecting the Computer and Copier
7
7.2.5 Connecting a Copier to the NetWare Server
Supported Environments
The controller supports the system environments described below.
NetWare version
NetWare 4.x
Protocol
IPX
Emulation
Service mode
NDS / Bindery
NDS / Bindery
PServer / NPrinter
PServer / NPrinter
NDPS (lpr)
NetWare 5.x/6
IPX
TCP/IP
Setting Up NetWare 4.x/ 5.x/ 6 Print Server Mode
1 Log in with administrator privileges.
2 Start up NWadmin.
3 Select the print service system or category container, and then select
“Print service quick setup” from the Tool menu.
4 Enter settings into the Print server name, Printer name, Print queue
name, and Volume name boxes, select Other/Unknown under Type
name, and then save the settings.
Note
Specify the users who can use the queue, printer options, number
of queues, and password. Refer to the NetWare documentation for
details.
5 Start up PageScope Light and log in to the Administrator mode, select
NetWare Configuration from the “Network” tab, and then use
PageScope Light to specify the following settings on the copier. (Refer
to “8 Using PageScope Light” for details.)
6 Load MONITOR.NLM using the NetWare server console.
NC-6
7-9
Connecting the Computer and Copier
7
7 Select the connection settings, and check that the PServer you
created is listed in the active connections section.
NDS
Bindery
[Enable NetWare] [*]
[Frame Type] [*]
Enable (Enabled if check box is selected.)
Auto detect (Select the frame type suitable for your network
environment.)
[Print Server Name]
[NDS Context Name]
Manually enter the name of the print server created in step 4.
The context name for the
Pserver
No settings required
[Print Server Password]
[Password Retype]
(Only specify this setting if it is also set on the NetWare server.)
(Only specify this setting if it is also set on the NetWare server.)
[Preferred File Server]
No settings required
The file server name for the
Pserver
[Preferred NDS Tree]
The tree name for Pserver
login
No settings required
[Print Queue Scan Rate] 1 (Change as necessary.)
[*]
[Connection Mode]
[Mode] [*]
Directory Services
PServer
Bindery
*
If changes are made to settings marked with “*”, turn the machine off, then on again.
Setting Up NetWare 4.x/ 5.x/ 6 Remote Printer Mode
1 Log in with administrator privileges.
2 Start up NWadmin.
3 Select the print service system or category container, and then select
“Print service quick setup” from the Tool menu.
4 Enter settings into the Print server name, Printer name, Print queue
name, and Volume name boxes, select Remote parallel, LPT1
under Type name, and then save the settings.
Note
Specify the users who can use the queue, printer options, number
of queues, and password. Refer to the NetWare documentation for
details.
7-10
NC-6
Connecting the Computer and Copier
7
5 Start up PageScope Light and log in to the Administrator mode, select
NetWare Configuration from the “Network” tab, and then use
PageScope Light to specify the following settings on the copier.
❍
Refer to “8 Using PageScope Light” for details.
6 Load MONITOR.NLM using the NetWare server console.
7 From the NetWare Server console, display the print server screen,
and check that the printer name entered in step 4 is displayed for
Printer 0 and that it is listed as “Waiting for job”.
NDS
Bindery
[Enable NetWare] [*]
[Frame Type] [*]
Enable (Enabled if check box is selected.)
Auto detect (Select the frame type suitable for your network
environment.)
[Print Server Name]
[NDS Context Name]
Manually enter the name of the print server created in step 4.
The context name for the
Pserver
No settings required
[Print Server Password]
[Password Retype]
(Only specify this setting if it is also set on the NetWare server.)
(Only specify this setting if it is also set on the NetWare server.)
[Preferred File Server]
No settings required
The file server name for the
Pserver
[Preferred NDS Tree]
The tree name for Pserver
login
No settings required
[Print Queue Scan Rate] 1 (Change as necessary.)
[*]
[Connection Mode]
[Mode] [*]
Directory Services
NPrinter
Bindery
*
If changes are made to settings marked with “*”, turn the machine off, then on again.
NC-6
7-11
Connecting the Computer and Copier
7
Setting Up NetWare 5.x/ 6 Novell Distributed Print Service (NDPS)
Note
Before specifying the NDPS settings, create the NDPS Broker and
NDPS Manager and check that they are loaded.
Check that the NetWare server is set to use the TCP/IP protocol.
Specify the IP address for the controller and check that it has started.
Creating an NDPS Printer Agent
1 Log in with administrator privileges.
2 Start up NWadmin.
3 Right-click the name of the organization or department container
where you want to create the Printer Agent, and then select NDPS
Printer.
4 In the NDPS Printer Name field, input the printer name.
5 In the Printer Agent Source field, select Create New Printer Agent,
and then click [Create].
6 Check the printer agent name, and then browse for the NDPS
Manager in the NDPS Manager Name field.
7 Under Gateway Types, select Novell Printer Gateway.
8 On the Novell DPS Settings window, select ((None)) for the printer and
Novell Port Handler for the port handler.
9 On the Connection Type window, select Remote Printer LPR/TCPIP.
10 Input the IP address assigned to the control as the host address and
“Print” for the printer name, and then click [Finish].
11 On the printer driver registration screen that appears, select None for
each operating system, and then finalize the registration.
Note
For information about configuring settings for printer user privileges,
printer alert options, and queue allocation, refer to the NetWare
documentation.
7-12
NC-6
Connecting the Computer and Copier
7
Setting Up the Windows Computer for the NetWare Client
1 Click [Start] - [Settings] - [Printer], and then double-click the “Add
Printer” icon.
2 For the printer port, browse the network and specify the name of the
queue (or the name of the NDPS printer) that you created.
3 On the printer model list, select the printer driver on the CD-ROM.
4 Follow the instructions provided by the Wizard to complete the
procedure.
NC-6
7-13
Connecting the Computer and Copier
7
7-14
NC-6
Using PageScope Light
8
8
Using PageScope Light
8.1
What is PageScope Light?
PageScope Light is a device control utility program provided by the HTTP
server built into the network interface card. This utility can be used with a
Web browser as an interface for remotely controlling the copier and
network interface card.
HTTP server
Access
NC-6
8-1
Using PageScope Light
8
Here are some examples of the types of tasks that can be performed with
PageScope Light.
G
Change Settings
Change network settings
Change printer settings (Only for copiers equipped with the optional
PCL printer controller)
G
Remote Status Monitoring
Check the details of copier trays, information about consumables, or
the total number of prints
Check the status of jobs that are being printed, or held in the print
queue (Jobs can also be deleted if you have logged in to the
Administrator mode.)
G
Maintenance
Reset the network card (NIC), or print controller
Initialize the print controller
Update the print controller firmware
8-2
NC-6
Using PageScope Light
8
8.2
System Requirements
PageScope Light can be used in the following system environments.
OS
Windows 95 (OSR 2.5), Windows 98,
Windows 98 SE, Windows ME, Windows NT
4.0, Windows 2000, or Windows XP
Browser
Microsoft Internet Explorer 4.0 or later
Netscape Navigator 4 or later
8.3
Accessing PageScope Light
PageScope Light is accessed directly using a Web browser.
1 Start up your Web browser.
2 Enter the IP address of the copier into the URL box, and then press
the [Enter] key.
http://<copier_IP_address>/
❍
(Example) If the copier IP address is 192.168.0.10, enter:
3 The PageScope Light screen appears.
Note
In order to access PageScope Light, an IP address must be assigned
to the copier.
8.4
Using PageScope Light
PageScope Light is used in the same way as other Internet Web pages.
Click on links in the page to jump to that page, and use the [Back] and
[Next] buttons to navigate through pages that have already been loaded.
NC-6
8-3
Using PageScope Light
8
8.5
About the Screen Layout
The following screen appears when you access PageScope Light.
Note
Screen images used in this manual may differ from the actual screen
display. They are also subject to change without notice.
1
2
3
5
6
4
7
1
2
3
4
Logo
Logo
Click on this to jump to the manufacturer’s Web site.
Click on this to jump to the PageScope Web site.
Displays the current status of the copier.
Status display
Administrator password
Enter the administrator password to log in to the
Administrator mode.
5
6
7
Tabs
These are used to select the various categories of
settings.
Menu
This is used to select various setting items or display
information.
Information/settings display Displays the details for the item selected from the
menu.
8-4
NC-6
Using PageScope Light
8
8.6
Logging In as an Administrator
Some of the settings available in PageScope Light can only be changed
by an administrator. These settings are only displayed when you log in to
the Administrator mode.
Logging In to Administrator Mode
1 Enter the administrator password in the “Admin Password:” box at the
left of the screen.
2 Click the [Login] button to log in to the Administrator mode.
3 To log out again, click the [Logout] button.
Note
The default password for Administrator mode is “sysadm”.
Be sure to change the administrator password before using
Administrator mode.
Note
The copier cannot be used while you are logged into PageScope
Light with Administrator mode.
8.7
About the File Download Function
If the copier that you are using is equipped with the optional PCL printer
controller, the File Download screen will appear when you click “File
Download” on the menu in the “Job” tab. Select the file in the “File Name”
box, and then click the [Send] button to download the file and print it from
the copier.
Types of File That Can Be Downloaded
Only the following types of file can be downloaded using the File
Download function.
G
PCL files
Text files
G
Note
If a file type other than a PCL or text file is downloaded, it will not be
printed, or will be printed with corrupt or incorrect characters.
NC-6
8-5
Using PageScope Light
8
8-6
NC-6
Appendix
9
9
Appendix
9.1
Product Specifications
Interface
Ethernet 10/100Base-T /TX (RJ-45)
TCP/IP Services
ARP, BootP*1, DHCP, DNS, IPP, lpr/lpd, Raw Socket, HTTPd
1.1, Telnetd, SLP, AutoIP*2
Netware Services
Bindery, NDS, PServer mode, NPrinter mode, NDPS
Frame Type (802.3, 802.2, 802.3 SNAP, Ethernet-II,
AutoDetect)
*1
This device supports the BootP protocol, which is part of the TCP/IP
protocol. If the BootP server has been enabled with the Network Setup
utility, the IP address for the copier will be automatically assigned. For
details, refer to the User Manual included on the PageScope CD.
*2
AutoIP is a function that allows the network interface card to
automatically assign IP addresses that begin with 169.254 and use a
subnet mask setting of 255.255.0.0. If there are two or more devices on
the same network that use the AutoIP function, these devices can
communicate with each other.
NC-6
9-1
Appendix
9
9.2
Troubleshooting
Check the following chart if you have problems using the copier as a
network printer.
Checkpoint
Possible cause
Solution
1
2
Has the print job
reached the copier?
Yes
A copier error has
occurred. (No paper,
no toner, etc.)
Check the copier and
resolve any errors.
No
The data has not
arrived at the copier.
See checkpoint 2.
Does the computer
respond when a ping
test is sent to the
controller?
Yes
The port number
setting is wrong.
Correct the port
number setting.
A computer
malfunction has
occurred.
Restart the computer.
The driver has not
been installed
correctly.
Uninstall the driver
software, and then
reinstall it according to
the instructions.
No
A copier malfunction
has occurred.
Restart the copier.
The network cable has Reconnect the cable,
become disconnected
or there is a problem
with the hub.
and restart or replace
the hub.
The IP address or
Correct the IP address
subnet mask setting is and subnet mask
wrong. setting.
9-2
NC-6
|