Kramer Electronics, Ltd.
USER MANUAL
Model:
WP-211DS
Wall Plate
ADDENDUM (this data is included at the end of the Overview section)
This addendum adds the following information to the user manual:
Caution – No operator-serviceable parts inside unit.
Warning – Use only the Kramer Electronics input power
wall adapter that is provided with this unit1.
Warning – Disconnect power and unplug unit from wall
before installing or removing device or servicing unit.
1 For example: model number AD2512C, part number 2535-000251
2900-9999992
A1
Introduction
1 Introduction
Welcome to Kramer Electronics (since 1981): a world of unique, creative and
affordable solutions to the infinite range of problems that confront the video,
audio and presentation professional on a daily basis. In recent years, we have
redesigned and upgraded most of our line, making the best even better! Our
350-plus different models now appear in 8 Groups1, which are clearly defined
by function.
Congratulations on purchasing your Kramer WP-211DS wall plate2, which is
ideal for any system requiring automatic computer and presentation routing
for computer graphics signals (up to UXGA and higher). The package
includes the WP-211DS wall plate and this user manual3.
2 Getting Started
We recommend that you:
ñ
Unpack the equipment carefully and save the original box and packaging
materials for possible future shipment
ñ
ñ
Review the contents of this user manual
Use Kramer high performance high resolution cables4
3 Overview
This section describes:
ñ
ñ
ñ
ñ
The power connect feature, see section 3.1
Using shielded twisted pair (STP)/unshielded twisted pair (UTP), see section 3.2
A summary of the WP-211DS, see section 3.3
Recommendations for achieving the best performance, see section 3.4
3.1 About the Power Connect Feature
The Power Connect feature lets you power a transmitter / receiver system by
connecting just one power adapter to either the transmitter or the receiver.
1 GROUP 1: Distribution Amplifiers; GROUP 2: Video and Audio Switchers, Matrix Switchers and Controllers; GROUP 3:
Video, Audio, VGA/XGA Processors; GROUP 4: Interfaces and Sync Processors; GROUP 5: Twisted Pair Interfaces;
GROUP 6: Accessories and Rack Adapters; GROUP 7: Scan Converters and Scalers; and GROUP 8: Cables and Connectors
2 Each wall plate is supplied with the required M3x4 screws
1
Overview
The other unit is fed over the same CAT5 cable. The Power Connect feature
applies as long as the CAT5 cable is heavy gauge cable (that is, it can carry
power). The distance does not exceed 50 meters on standard cable.
For a distance of 100 meters, separate power supplies must be connected to
the transmitter and to the receiver simultaneously, unless using heavy gauge
CAT5 cable.
3.2 Shielded Twisted Pair (STP) / Unshielded Twisted Pair (UTP)
The decision whether to use shielded twisted pair (STP) cable or unshielded
twisted pair (UTP) cable depends on the nature of the application.
It is recommended that in applications with high interference, shielded
twisted pair (STP) cable will give better results. However, the shield itself
does create a capacitance that degrades the frequency response of the
machines. For shorter distances, of 50m or so, shielded twisted pair (STP)
cable is preferred because it provides protection from interference
(degradation is non apparent).
For a long range application, unshielded twisted pair (UTP) cable is preferred.
However, the unshielded twisted pair (UTP) cable should be installed far
away from electric cables, motors etc., which are prone to create electrical
interference.
3.3 About the WP-211DS
Your Kramer WP-211DS Wall Plate—available in 4 versions: one for
Belgium, one for Germany, one for England (and the rest of Europe), and one
for the USA— is a high performance 2x1 automatic switcher for computer
graphics and stereo audio signals. The WP-211DS detects the presence of the
active XGA-type input signal from either IN 1 (the default) or IN 2, and
automatically routes it to the acceptor connected to the rear panel XGA OUT
and the AUDIO OUT connectors. In addition, the WP-211DS:
ñ
With its video bandwidth exceeding 260MHz, ensures transparent
operation at the highest resolutions
Automatically switches the stereo audio signal with the video signal
(audio-follow-video) when switching the active input to the output
Includes a DEFAULT SELECT switch for selecting the computer
graphics master (default) source signal
ñ
ñ
ñ
ñ
ñ
ñ
Includes a looping XGA input
Comes with contact closure remote control for forced operation
Includes a CAT5 output (for video) via an 8 PIN terminal block connector
Is powered by a standard 12 Volt DC feed
KRAMER: SIMPLE CREATIVE TECHNOLOGY
2
Your WP-211DS
3.4 Recommendations for Achieving the Best Performance
Achieving the best performance means:
ñ
Connecting only good quality connection cables, thus avoiding
interference, deterioration in signal quality due to poor matching, and elevated
noise levels (often associated with low quality cables)
ñ
Avoiding interference from neighboring electrical appliances that may
adversely influence signal quality, and positioning your WP-211DS away
from moisture, excessive sunlight and dust
4 Your WP-211DS
Figure 1 and Table 1 define the front panel of the WP-211DS:
Figure 1: WP-211DS Front Panel
3
Your WP-211DS
Table 1: WP-211DS Front Panel Features
Function
#
1
2
3
Feature
XGA INPUT 2 HD15F Connector
DEFAULT SELECT Switch
IN 2 Green LED
Connects to the computer graphics source 2
Slide to left for input 2, slide to right for input 1
Lights when the XGA INPUT 2 source is active
4
5
6
7
8
IN 1 Green LED
Lights when the XGA INPUT 1 source is active
Connects to the computer graphics source 1
Connects to audio source 2
Connects to audio source 1
Lights when the image is turned off, displaying a blank screen
XGA INPUT 1 HD15F Connector
AUDIO IN 2 mini plug Connector
AUDIO IN 1 mini plug Connector
Red LED
9
Button
Blanks the screen1
10 POWER LED
Lights when receiving power
11 LOOP HD15F Connector
For XGA looping to increase output availability (for example, to
connect to an additional monitor)
Figure 2 and Table 2 define the rear panel of the WP-211DS:
Figure 2: WP-211DS Rear Panel
Table 2: WP-211DS Rear Panel Features
#
Feature
Function
12 POWER SUPPLY Terminal GND PIN Connect (-) to the Ground
Block Connector
12V PIN Connect (+) to the connector for powering the unit
13 AUDIO OUT Terminal Block Connector Connects to the audio acceptor
14 XGA OUT Terminal Block Connector
Connects to the computer graphics (RGBHV) acceptor
15 REM (Remote) IN 1 and IN 2 Terminal Connect to a dry contact switch (see section 5.5)
Block Connectors
16 CAT5 OUTPUT Terminal Block
Connector
Connects to the CAT5 line input on the XGA Line Receiver
(see section 5.2)
1 R, G and B signals are blocked, but the H and V (and also audio) are passed through
KRAMER: SIMPLE CREATIVE TECHNOLOGY
4
Using the WP-211DS
5 Using the WP-211DS
For details of how to:
ñ
ñ
ñ
ñ
ñ
Install your WP-211DS, see section 5.1
Wire the CAT5 LINE IN / LINE OUT RJ-45 connectors, see section 5.2
Connect your WP-211DS, see section 5.3
Select the default master source signal, see section 5.4
Connect the REMOTE connector, see section 5.5
You can use your WP-211DS, for example, in a conference room, as the
example in Figure 3 illustrates:
Figure 3: Example of a Conference Room WP-211DS Installation
5.1 Installing the WP-211DS
To install your WP-211DS, connect each of the following terminal block output
connectors to the pre-installed wiring in the wall box opening1, the:
1. XGA OUT RGBHV 10 PIN. It connects to the XGA acceptor (for example, a
projector).
2. AUDIO OUT 3 PIN. It connects to the audio acceptor (for example, a pair of
speakers).
3. CAT5 OUTPUT 8 PIN. It connects to the CAT5 line input.
4. REM 3 PIN. It connects to the remote connector (see section 5.5).
In addition:
ñ
Connect the 12V DC power supply to the POWER SUPPLY pins2, taking
care that polarity is correct
ñ
Insert the WP-211DS directly into the wall box opening, and then mount
the front panel securely using the screws
1 As required. Some features may not be required in an installation
2 Connect the wire labeled “+” to the +12V pin, and the wire labeled “–” to the GND pin
5
Using the WP-211DS
5.2 Wiring the CAT5 LINE IN / LINE OUT RJ-45 Connectors
Table 3 and Figure 4 define the UTP CAT5 PINOUT, using pin to pin wiring
to connect the WP-211DS output to the TP-120 input:
Figure 4: CAT5 PINOUT
Table 3: CAT5 PINOUT
TP-120 CAT5
INPUT
WP-211DS
CAT5 OUTPUT
PIN Wire Color
PIN
1
2
3
4
5
6
7
8
Wire Color
1
2
3
4
5
6
7
8
BLUE(--)
BLUE(+)
GREEN(--)
+12VDC
GND
GREEN(+)
RED(--)
RED(+)
BLUE(--)
BLUE(+)
GREEN(--)
+12VDC
GND
GREEN(+)
RED(--)
RED(+)
KRAMER: SIMPLE CREATIVE TECHNOLOGY
6
Using the WP-211DS
5.3 Connecting the WP-211DS
To connect your WP-211DS, do the following:
1. Connect a computer graphics (master) source to the XGA INPUT 1 HD15F
connector and to the AUDIO IN 1 3.5mm mini jack, for example, using a
Kramer C-GMA/GMA cable1.
2. Set the DEFAULT SELECT switch to IN 1 (the factory preset default) or
IN 2, as section 5.4 describes.
3. Connect a second computer graphics source to the XGA INPUT 2 HD15F
connector and to the AUDIO IN 2 3.5mm mini jack, for example, using a
Kramer C-GMA/GMA cable1.
4. Connect an additional display to the LOOP HD15F connector (optional).
Figure 5: Example of a WP-211DS Installation
1 XGA HD15M +Audio jack to XGA HD15M +Audio jack (not supplied). The complete list of Kramer cables is on our Web
connector, and a separate audio source to the AUDIO IN
7
Using the WP-211DS
5.4 Operating using the Default Master Source Signal Selection
The DEFAULT SELECT switch is factory preset to IN 1 and the WP-211DS
will detect the presence of the master source signal at the XGA INPUT 1
connector. If you connect active sources to both the XGA INPUT 1 and the
XGA INPUT 2 connectors, the source at the XGA INPUT 1 connector takes
priority over the source at the XGA INPUT 2 connector and it is routed to the
XGA OUT and the AUDIO OUT connectors (audio follows the video).
You can change the default so that the WP-211DS automatically detects an
active source signal from XGA INPUT 2, by setting the DEFAULT SELECT
switch to IN 2. When active, the source at the XGA IN 2 connector takes
priority over the source at the XGA INPUT 1 connector and it is routed to the
XGA OUT and the AUDIO OUT connectors (audio follows the video).
If the WP-211DS detects:
ñ
No signal1 at the XGA INPUT 1 input (when INPUT 1 is selected as the
default), the WP-211DS routes the signal from the source at XGA INPUT 2
and AUDIO IN 2 to the XGA OUT and the AUDIO OUT connectors.
Similarly, if the WP-211DS detects no signal at the XGA INPUT 2 input
(when IN 2 is selected as the default), the WP-211DS routes the signal from
the source at XGA INPUT 1 and AUDIO IN 1 to the XGA OUT and the
AUDIO OUT connectors
ñ
A signal from the XGA source at XGA INPUT 1 input (when IN 1 is
selected as the default), while routing the signal from the XGA source at XGA
INPUT 2, the WP-211DS will reroute the signal from the XGA source at
XGA INPUT 1 and AUDIO IN 1 to the XGA OUT and the AUDIO OUT
connectors. Similarly, if the WP-211DS detects a signal from the XGA source
at XGA INPUT 2 input (when IN 2 is selected as the default), while routing
the signal from the XGA source at XGA INPUT 1, the WP-211DS will
reroute the signal from the XGA source at XGA INPUT 2 and AUDIO IN 2 to
the XGA OUT and the AUDIO OUT connectors
ñ
No signal at all (that is, when there is no active input from a source at
XGA INPUT 1 or at XGA INPUT 2), the WP-211DS will still route XGA
INPUT 2 and AUDIO IN 2 to the XGA OUT and AUDIO OUT connectors,
and continue to examine XGA INPUT 1 input (when IN 1 is selected as the
default), switching back to it when it detects a valid signal. Similarly, if the
WP-211DS detects no signal at all (when IN 2 is selected as the default), it
will still route XGA INPUT 1 and AUDIO IN 1 to the XGA OUT and AUDIO
OUT connectors, and continue to examine XGA INPUT 2 input, switching
back to it when it detects a valid signal
1 Perhaps no source is connected, or that source is connected but its power is OFF
KRAMER: SIMPLE CREATIVE TECHNOLOGY
8
Using the WP-211DS
5.5 Connecting the REMOTE Connector
You can force the routing of one of the 2 inputs to the XGA output by remote
control. To do so, connect the appropriate REMOTE input terminal block
connector pins to a dry contact switch1. For example, as Figure 6 illustrates, to
route REMOTE IN 1 to the XGA output, connect PIN 1 to the Ground. To route
REMOTE IN 2 to the XGA output, connect PIN 2 to the Ground pin. Do not
connect both the REMOTE IN 1 and the REMOTE IN 2 to the Ground pin
simultaneously.
Route input 1 to the output, by
attaching PIN 1 to the Ground:
Route input 2 to the output, by
attaching PIN 2 to the Ground:
Figure 6: Remote Terminal Block Connector
When both XGA INPUT 1 and XGA INPUT 2 are connected, the signal from
XGA INPUT 1 routes to the output (factory default). However, you can force
the routing of XGA INPUT 2 to the output by attaching PIN 2 to the Ground.
Even if no input is present on XGA INPUT 1, you can force the routing of the
output from XGA INPUT 1 (displaying a blank screen) by attaching PIN 2 to
the Ground.
1 Note that the connection should be permanent, since the WP-211DS will revert to an automatic switcher when the
connection is removed
9
Technical Specifications
6 Technical Specifications
Table 4 includes the technical specifications:
Table 4: Technical Specifications1 of the WP-211DS
INPUTS:
2 XGA on HD15F connectors
2 unbalanced stereo audio on 3.5 mm mini audio connectors
OUTPUTS:
1 XGA (RGBHV) on a 10 PIN terminal block connector
1 XGA on an HD15F connector (input #1 loop)
1 unbalanced stereo audio on a 3 PIN terminal block connector
1 CAT5 (for video) on an 8 PIN terminal block connector
MAX. OUTPUT LEVEL:
BANDWIDTH (-3dB):
DIFF. GAIN:
VIDEO: 1Vpp (XGA)
VIDEO: 260MHz (XGA)
0.05% (XGA)
AUDIO: 4dBm
AUDIO: 20kHz
DIFF. PHASE:
K-FACTOR:
0.1% (XGA)
0.3% (XGA)
S/N RATIO:
VIDEO: 74dB
AUDIO: 80dB
CROSSTALK (all hostile): VIDEO: –59dB @ 100MHz
CONTROLS:
Contact closure remote control, input default selection switch, Image off button
COUPLING:
AUDIO THD + NOISE:
VIDEO: DC
0.017%
AUDIO: DC
AUDIO 2nd HARMONIC: 0.005%
POWER SOURCE:
DIMENSIONS:
12 VDC, 330mA
Belgium: 15.1cm x 8.0cm x 3.84cm (5.95" x 3.15" x 1.51"), W, H, D
Germany: 15.1cm x 8.0cm x 3.84cm (5.95" x 3.15" x 1.51"), W, H, D
England and Europe: 14.6cm x 8.6cm x 3.84cm (5.75" x 3.39" x 1.51"), W, H, D
USA: 16.2cm x 11.4cm x 3.9cm (6.4" x 4.5" x 1.55"), W, H, D
WEIGHT:
0.3 kg (0.67 lbs.) approx
1 Specifications are subject to change without notice
KRAMER: SIMPLE CREATIVE TECHNOLOGY
10
LIMITED WARRANTY
Kramer Electronics (hereafter Kramer) warrants this product free from defects in material and workmanship under the
following terms.
HOW LONG IS THE WARRANTY
Labor and parts are warranted for seven years from the date of the first customer purchase.
WHO IS PROTECTED?
Only the first purchase customer may enforce this warranty.
WHAT IS COVERED AND WHAT IS NOT COVERED
Except as below, this warranty covers all defects in material or workmanship in this product. The following are not covered
by the warranty:
1.
Any product which is not distributed by Kramer, or which is not purchased from an authorized Kramer dealer. If you are
uncertain as to whether dealer is authorized, please contact Kramer at one of the agents listed in the web site
a
2.
3.
Any product, on which the serial number has been defaced, modified or removed.
Damage, deterioration or malfunction resulting from:
i)
ii)
iii)
iv)
v)
Accident, misuse, abuse, neglect, fire, water, lightning or other acts of nature
Product modification, or failure to follow instructions supplied with the product
Repair or attempted repair by anyone not authorized by Kramer
Any shipment of the product (claims must be presented to the carrier)
Removal or installation of the product
vi)
vii)
Any other cause, which does not relate to a product defect
Cartons, equipment enclosures, cables or accessories used in conjunction with the product
WHAT WE WILL PAY FOR AND WHAT WE WILL NOT PAY FOR
We will pay labor and material expenses for covered items. We will not pay for the following:
1.
2.
Removal or installations charges.
Costs of initial technical adjustments (set-up), including adjustment of user controls or programming. These costs are the
responsibility of the Kramer dealer from whom the product was purchased.
3.
Shipping charges.
HOW YOU CAN GET WARRANTY SERVICE
1.
2.
To obtain service on you product, you must take or ship it prepaid to any authorized Kramer service center.
Whenever warranty service is required, the original dated invoice (or a copy) must be presented as proof of warranty coverage,
and should be included in any shipment of the product. Please also include in any mailing a contact name, company, address, and
a description of the problem(s).
3.
For the name of the nearest Kramer authorized service center, consult your authorized dealer.
LIMITATION OF IMPLIED WARRANTIES
All implied warranties, including warranties of merchantability and fitness for a particular purpose, are limited in duration to
the length of this warranty.
EXCLUSION OF DAMAGES
The liability of Kramer for any effective products is limited to the repair or replacement of the product at our option. Kramer
shall not be liable for:
1.
Damage to other property caused by defects in this product, damages based upon inconvenience, loss of use of the product, loss
of time, commercial loss; or:
2.
Any other damages, whether incidental, consequential or otherwise. Some countries may not allow limitations on how long an
implied warranty lasts and/or do not allow the exclusion or limitation of incidental or consequential damages, so the above
limitations and exclusions may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights, which vary from place to place.
NOTE: All products returned to Kramer for service must have prior approval. This may be obtained from your dealer.
This equipment has been tested to determine compliance with the requirements of:
EN-50081:
"Electromagnetic compatibility (EMC);
generic emission standard.
Part 1: Residential, commercial and light industry"
"Electromagnetic compatibility (EMC) generic immunity standard.
Part 1: Residential, commercial and light industry environment".
FCC Rules and Regulations:
EN-50082:
CFR-47:
Part 15: “Radio frequency devices
Subpart B – Unintentional radiators”
CAUTION!
⁄
Servicing the machines can only be done by an authorized Kramer technician. Any user who makes changes or modifications to
the unit without the expressed approval of the manufacturer will void user authority to operate the equipment.
Use the supplied DC power supply to feed power to the machine.
⁄
⁄
Please use recommended interconnection cables to connect the machine to other components.
11
For the latest information on our products and a list of Kramer
where updates to this user manual may be found.
We welcome your questions, comments and feedback.
Safety Warning:
Disconnect the unit from the power supply before
opening/servicing.
Caution
Kramer Electronics, Ltd.
E-mail: [email protected]
P/N: 2900-000078 REV 3
|