FNC-0115
100FX Multi-mode SC Fiber Optic PCI Express Card
User Manual
Ver. 1.00-0801
Caution
Circuit devices are sensitive to static electricity, which can damage their delicate
electronics. Dry weather conditions or walking across a carpeted floor may cause you to
acquire a static electrical charge.
To protect your device, always:
•
Touch the metal chassis of your computer to ground the static electrical charge before
you pick up the circuit device.
•
Pick up the device by holding it on the left and right edges only.
Electronic Emission Notices
Federal Communications Commission (FCC) Statement
This equipment has been tested and found to comply with the limits for a class B
computing device pursuant to Subpart J of part 15 of FCC Rules, which are designed to
provide reasonable protection against such interference when operated in a commercial
environment.
European Community (CE) Electromagnetic Compatibility Directive
This equipment has been tested and found to comply with the protection requirements
of European Emission Standard EN55022/EN60555-2 and the Generic European Immunity
Standard EN50082-1.
EMC:
EN55022(1988)/CISPR-22(1985) class B
EN60555-2(1995)
EN60555-3
class B
IEC1000-4-2(1995)
IEC1000-4-3(1995)
IEC1000-4-4(1995)
4K V CD, 8KV, AD
3V/m
1KV – (power line), 0.5KV – (signal line)
1. Overview
Fast Ethernet PCI-e 100Base-FX Fiber Adapter is a Fast Ethernet Board that fully
complies with all IEEE 802.3u and 100Base-FX standards. Two LED indicators
(LINK/ACT and FDX) on the bracket will help to oversee the board link, activities
and full-duplex status.
Fast Ethernet PCI-e 100Base-FX Fiber adapters support Pre-boot Execution
Environment (PXE), Remote Program Load (RPL), and Bootstrap Protocol
(BOOTP). Multi-Boot Agent (MBA) is a software module that allows your networked
system to boot with the images provided by remote systems across the network.
2. Checklist
Before you start installing the PCI-e 100Base-FX Fiber Adapter, verify that the
package contains the following items:
Fast Ethernet PCI-e 100Base-FX Fiber Adapter
LAN Driver and User’s Guide CD-ROM
Please notify your sales representative immediately if any of the aforementioned
items is missing or damaged.
3. Model Description
PCI-e 100Base-FX Board Models
Fiber Transceiver
SC multi-mode
Wavelength
1310nm
4. Network Remote Boot Configuration
4.1 Select Remote Boot Type
For entering “MBA Configuration Menu” to select Remote Boot Type (PXE,
RPL), please press Shift-F10 within 3 seconds after power on your PC,
otherwise, the system would go to Windows O.S.
4.2 Set Network Remote Boot
For setting network remote boot, please enter PC BIOS first, then select
“Boot” tab, after that, choose “MBA” as the priority first boot device.
4.3 Cancel Network Remote Boot
To cancel network remote boot, please change the “Boot” setting in PC
BIOS from “MBA” to “Hard Drive” or other devices.
1
5. LED Description
LED
LINK/ACT
FDX
Color
Green
Green
Function
Lit when cable connection is good
and speed is at 100Mbps.
Blinks when any traffic is present.
Lit when full-duplex mode is active.
6. Wake on LAN
The Wake on LAN function on this adapter can recognize a wake-up frame and
signal the PC to power up.
The default value of WOL (Wake on LAN) function is ON. You can also disable the
WOL function by putting the jumper on the pin 1 and pin 2.
Never drop the jumper, otherwise FNC-0115 will be lack of electricity.
J1
3
2
ON
OFF
1
Wake on LAN select Jumper (J1)
2
7. Network Parameter
Multi-mode Fiber 62.5/125um, 50/125um
Full Duplex
2000m
LINK/ACT
FDX
TX
RX
Fig. 1 Diagnostic LEDs and Bracket
3
8. Technical Specifications
Standards
: IEEE 802.3u Fast Ethernet 100Base-FX
IEEE 802.3x Full-Duplex Flow Control
IEEE 802.1Q VLAN
Connector
: 1310nm SC multi-mode
Fiber Optic Cable:
62.5/125, 50/125
µm multi-mode
Data Transfer Mode/Speed:
Full duplex (Default) mode
100Mbps speed
Diagnostics LED on Bracket:
LINK/ACT
FDX
Bus Slot
: PCI-e 1.0 Compliant
Power Requirement : Max. 3W, +3.3VDC@1A
Ambient Temperature : 0° to 50°C
Humidity
Emission
: 5% to 90%
: Complies with EMI Standard
FCC Class B
CE Mark
4
|