Model F200-2
Instruction Manual
PICTURE FRAMING
Precision
SANDER Elite
Description
The Model F200-2 Precision Sander Elite has been designed to improve saw cut miters
to perfect 45˚. A new 10” diameter wheel can accommodate most moulding sizes. After
sanding the miters, the result is a sharp seamless frame corner that is of professional
quality. The Model F200-2 Precision Sander Elite is a precision tool and will give many
years of service. Producing professional quality picture frames is now easier than ever!
847-526-5515
Purchase Date
Model F200-2
Instruction Manual
Precision SANDER ELITE
Operation
Preparation
1. Rotate alignment bar to either side
by lifting and turning (Fig. 3)
Sanding
Fig. 3
1. Place back of moulding against
alignment bar with finish side up.
2. Slide moulding against wheel.
3. With one hand, hold moulding firmly
against alignment bar and wheel.
With other hand, rotate wheel
in the direction of the moulding
or downward onto the top of the
moulding.
(Figs. 4a and 4b)
4. Rotate wheel 4-6 times.
• Adjust the pressure against
the wheel while rotating. Start
with light pressure until wheel
is spinning, then increase the
pressure for easier sanding.
Fig. 4b
Right Side
Fig. 4a
Left Side
5. Check sanded surface of moulding
to see if surface is smooth.
6. Repeat until full surface is smooth.
Check Lengths It is important both sides of
moulding are same length for square frame
and seamless corners.
1. Lay two moulding pieces side-by-
side so miters are facing up.
2. Align the two lower edges.
3. Check to see if the upper edges are
Fig. 5
Check top
even in length (Fig. 5).
4. If not, sand longer piece until it’s
even with short piece.
Moulding
Pieces
Align Bottom
3
Logan Graphic Products Inc., 1100 Brown Street, Wauconda, IL 60084 847-526-5515 www.logangraphic.com
Instruction Manual
Precision SANDER ELITE
Model F200-2
Cleaning
Fig. 6
1. Hold the cleaning bar at 45 degrees and move down the length of
the wheel while rotating (Fig. 6).
2. Use light pressure. NOTE: Surface of sandpaper may not look clean
but it is. The dust sticks to the backing material not the raised
abrasive grit.
Adjustment 45°
1. Remove sand paper
2. Place the 45˚ square flat against the wheel and up against bar
(Fig. 7). Look for gaps against the bar.
3. Adjust the bar using adjustment wrench until gap disappears.
Fig. 7
Changing Disk Paper
45° Triangle
1. Remove disk using disk wrench.
2. Remove worn sandpaper and clean surface of disk of any glue or
debris using a razor blade or mineral spirits.
3. Peel off adhesive backing and apply sandpaper
to disk carefully. Press thoroughly to remove any bubbles.
Trouble Shooting
Problem
Solution
Moulding splinters.
Reverse sanding direction.
Apply less pressure to surface being sanded.
Not producing 45 degree angle.
Refer to instructions for making adjustments using micro-adjustment blocks. Only small incre-
mental adjustments are required.
Remove any debris between moulding and fence.
Remove any debris between fence and micro-adjustment stop(s).
Make sure center bolt on sanding wheel is tight.
Clean sanding disk with supplied cleaning bar.
Replace sand paper disk.
Rough surface after sanding.
Gaps appear in moulding joints.
Apply less pressure to surface being sanded.
Sand surface until a fine line of dust appears across the top of the moulding.
Warranty
Logan Graphic Products, Inc. (“Logan”) warrants the Precision Sander Elite - Model F200-2, to be free from defects in parts and workmanship for a period of one
year from the date of original purchase. Logan warrants that it will either repair or replace, at its’ sole discretion, any necessary replacement parts found to be
defective. Should the product need to be returned to Logan for repair or replacement parts, authorization for any return must come from Logan in writing. Costs of
returning the product to Logan, including insurances, shall be borne by the purchaser. Logan shall not be liable for any damages or losses, incidental or consequen-
tial, direct or indirect, arising from the use of this product. This warranty extends only to the original purchaser and is not assignable or transferable. This warranty is
in lieu of all other warranties, expressed or implied.
Logan Graphic Products Inc., 1100 Brown Street, Wauconda, IL 60084 847-526-5515 www.logangraphic.com
L689N2 1/10
|