P721UTa
SMART TEMP® UNIVERSAL
7-DAY PROGRAMMABLE TOUCHSCREEN THERMOSTAT
(FOR BOTH CONVENTIONAL AND HEAT PUMP SYSTEMS)
INSTALLATION AND OPERATING INSTRUCTIONS
52139
IMPORTANT!
• Please read all of these instructions carefully before beginning
installation.
• Label every wire terminal designation on your existing thermostat wiring
before removing your old thermostat.
• Ignore the color of the wires since they may not comply with any
standard. Please connect wires using the terminal letter designations.
Thank you for your confidence in our product. To obtain the best results from
your investment, please read and follow the installation procedures carefully, and
one step at a time. This will save you time and minimize the chance of damaging
either the thermostat or possibly your heating and cooling system. These
instructions may contain information beyond that which may be required for your
particular installation.
CAUTIONS AND WARNINGS . . . . . . . . . . 2
SYSTEM COMPATIBILITY . . . . . . . . . . . . 3
FEATURES . . . . . . . . . . . . . . . . . . . . . . . 4
TOOLS YOU MAY NEED . . . . . . . . . . . . . . 4
MOUNTING LOCATION . . . . . . . . . . . . . . 5
REMOVE OLD THERMOSTAT . . . . . . . . . . 5
INSTALL THERMOSTAT BASE . . . . . . . . . 6
WIRING INFORMATION . . . . . . . . . . . . . . 7
WIRING DIAGRAMS . . . . . . . . . . . . . . . . 9
HARDWARE SETUP OPTIONS . . . . . . . . 18
COMPLETE THE INSTALL . . . . . . . . . . . 20
FRONT PANEL ITEMS . . . . . . . . . . . . . . 20
OPERATING INSTRUCTIONS . . . . . . . . . 21
TEMPERATURE PROGRAMS . . . . . . . . . 24
ADVANCED FEATURES . . . . . . . . . . . . . 25
BATTERY REPLACEMENT . . . . . . . . . . . 33
TECHNICAL ASSISTANCE . . . . . . . . . . . 34
LIMITED WARRANTY . . . . . . . . . . . . . . 34
MERCURY NOTICE . . . . . . . . . . . . . . . . 34
WARNING: Use Energizer® or DURACELL® Alkaline Batteries Only.
Energizer® is a registered trademark of Eveready Battery Company, Inc.
DURACELL® is a registered trademark of The Procter & Gamble Company
© 2013 LUX PRODUCTS CORPORATION. ALL RIGHTS RESERVED
P721UTa
Fan
Mode
Switch
Menu
Button
FAN
AUTO
ON
MENU
˚
F
PM
˚
F
SET
HEAT
OFF
Clock
COOL
System
Mode
Switch
Room Temperature
Set Temperature
SYSTEM COMPATIBILITY:
The electrical rating for this thermostat is 1.5 Amps per terminal, with a
maximum total combined load of 3.0A for all terminals combined.
COMPATIBLE WITH:
• Most 24-volt heating and cooling systems
• 1 or 2 stage Heat / 1 stage Cool: Gas, Oil or Electric systems
• 1 or 2 stage Heat / 1 stage Cool: Heat Pump systems
• 3-wire hydronic (hot water) zone valves
• Gas Millivolt heaters
NOT COMPATIBLE WITH:
• 120/240 VAC line-voltage systems (without a transformer), ask your LUXPRO
dealer for thermostats to control these systems.
3
FEATURES:
• 1 or 2-Heat / 1-Cool, 7-day programming
• Universal Compatibility for all system types
• Each day of the week can be programmed separately
• Easy to use, touchscreen menu operation
• User-selectable periods per day (2 or 4)
• User-selectable programmable or non-programmable operation
• LuxLight® EL (Electro-Luminescent) lighted display
• Energy usage monitor
• Programmable air filter life timer
• Programmable keypad lockout for unauthorized users
• Manual temperature hold
• Adjustable vacation hold (1 to 30 days)
• Temporary temperature override
• Adjustable temperature differential / cycle-rate
• Adjustable 2nd heat stage Offset setting
• User temperature calibration
• Adjustable heat/cool set temperature limit stops
• Smart recovery
• Dual-powered (battery and/or 24-volt system powered)
• Battery-free memory storage
• F/C temperature display
• 12/24-hour clock display
• 5/2-minute selectable time delay for equipment protection
TOOLS YOU MAY NEED:
• Screwdrivers
• Wire Stripper
• Wire Cutter
• Drill with assorted drill bits (new installations only)
4
MOUNTING LOCATION:
On replacement installations, mount the new thermostat in place of the old one
unless the conditions listed below suggest otherwise. On new installations,
please follow these general guidelines:
1. Mount the thermostat on an inside wall, about 5 ft. (1.5m) above the floor.
2. Do not locate the thermostat where air circulation is poor such as in a corner,
alcove, or behind a door that is normally left open.
3. Do not locate the thermostat where unusual heating or cooling conditions may
be present, such as: direct sunlight, above a lamp, television, or radiator, or on
a wall next to an exterior door or window.
4. Do not locate in a damp environment, as this can lead to corrosion that may
shorten thermostat life.
5. If painting or construction work is still ongoing, cover the thermostat
completely or wait until this work is complete before installation.
WARNING:
All wiring must conform to the local codes and ordinances that are in your
particular location.
REMOVE OLD THERMOSTAT:
1. Turn OFF the electricity to all heating and cooling
components. Do not turn the electricity back on until
all work is completed.
2. Remove the front portion of your old thermostat to
F
OF
expose the wiring connections.
3. Write down the letters printed near each wire terminal
that is used, and also the color of each wire that is
connected to it. Self-adhesive wire labels are also
enclosed.
4. Carefully remove the wires one at a time, and bend them in a manner so that
they do not fall back inside the wall. Do not allow bare wire ends to touch
each other.
5. Loosen the mounting screws for the old thermostat and carefully remove it
from the wall.
5
INSTALL THERMOSTAT BASE:
Mode
Switches
THERMOSTAT TOP VIEW
1. Strip wire insulation leaving only 3/8 in. (9.5mm) bare wire ends, and clean off
any corrosion present.
2. Fill the wall opening with non-combustible insulation to prevent drafts from
affecting the thermostat’s normal operation.
3. Separate new thermostat housing using your thumb and index finger. Provide
pressure in opposite directions to the release tabs on the top of the housing,
in the directions shown in the diagram shown above.
4. Route the wires through the opening in the new thermostat base plate, and
hold the base against the wall. Try to line up the screw holes from the prior
thermostat, and install the mounting screws.
5. If the previous holes cannot be used, hold the thermostat base against the
wall so that it appears straight and level (position the base for best
appearance) and mark for the new screw holes. Attach the base to the wall
using the screws provided (use the supplied plastic anchors if needed when
mounting to a soft material such as drywall).
6
WIRING INFORMATION:
CONNECTING THE WIRES:
When attaching the wires to the thermostat, please ensure that the bare wire
ends are held ALL the way into the terminal block while the screw is being
tightened.
WIRING BASE PLATE NOTICE:
This thermostat model is part of a family of similar models that have the same
general visual appearance. Even though this base plate may look the same as
base plates from other models, the wiring connections may have different
terminal letters for different purposes. Please do not interchange the back plates
and/or thermostat front halves of other similar looking models. Doing so may
cause undesired heating and/or cooling operation to occur.
7
WIRING DIAGRAM NOTES:
(Important, please read all notes before connecting wires)
• If the information provided in the following wiring diagrams does not clearly
represent or match your system, please refer to the “TECHNICAL ASSISTANCE”
section of this manual, and contact us before removing any of your existing
thermostat wiring.
• All of the dashed wires shown in the wiring diagrams are either optional, or
their usage depends upon your specific system type or brand. For example:
Diagram #1 shows the fan wire as optional. If your system does not have a
fan, than this terminal will not be used.
• Terminal letters shown in black represent typical wiring applications.
Depending upon the brand of your specific system or thermostat, your terminal
letters may not match exactly. Terminal letters shown in gray represent other
possible wiring designations that you might see on your existing thermostat
terminals.
• The optional “C” terminal is used for powering the thermostat by the 24-volt
system, using the System Common wire. This can be used alone, or in
addition to installing batteries as a backup. NOTE: connecting the System
Common wire to the thermostat is not necessary for heating and cooling to
function properly.
• If your old thermostat has both a “Y” and “C” wire present, then “C” is most
likely a System Common wire.
• For Heat Pump systems, you will use either the “O” terminal or the “B”
terminal on this thermostat, but not both. If your old thermostat has both an
“O” and a “B” wire present, then “B” is likely a System Common wire and may
be connected to the “C” terminal. Connecting a System Common wire to this
thermostat’s “B” terminal may damage the thermostat, and also your heating
and cooling system.
• Some Heat Pump systems have a wire for AUX electric heat (usually W2), and
also a separate wire for Emergency electric heat (usually E). This thermostat
uses the W2 terminal for both AUX and Emergency Heat. Tape off your “E”
wire, and confirm that all components function without it.
• If replacing an old thermostat that has a mechanical clock, there may be two
wires labeled as “C” for the clock power. Tape off these wires and do not
connect them to the “C” terminal of this thermostat.
8
WIRING DIAGRAMS:
DIAGRAM
SYSTEM TYPE / DESCRIPTION
PAGE #
#1
#2
#3
#4
#5
#6
#7
#8
CONVENTIONAL:
CONVENTIONAL:
CONVENTIONAL:
CONVENTIONAL:
CONVENTIONAL:
CONVENTIONAL:
HEAT PUMP:
HEATING ..........................................................10
1-STAGE OR 2-STAGE
2, 3, 4, 5 WIRES
HEATING ..........................................................11
3-WIRE ZONE VALVE
3, 4 WIRES
COOLING ..........................................................12
1-STAGE
3, 4 WIRES
HEATING AND COOLING .....................................13
1-STAGE HEAT
4, 5 WIRES
HEATING AND COOLING .....................................14
2-STAGE HEAT
5, 6 WIRES
HEATING AND COOLING .....................................15
TWO-TRANSFORMERS
5, 6 WIRES
HEATING AND COOLING .....................................16
SINGLE-STAGE ONLY
4, 5 WIRES
HEAT PUMP:
HEATING AND COOLING .....................................17
WITH AUX / EMERGENCY HEAT
5, 6 WIRES
9
10
11
12
13
14
15
16
17
HARDWARE SETUP OPTIONS:
On the thermostat’s circuit board, there is a row of DIP switches, labeled #1
through #7. The position of these switches will change how the thermostat
operates, and also how information is conveyed to you on the LCD display
screen. If you make any changes to these options, the changes are not
recognized unless you either: change the position
7
of the HEAT/OFF/COOL mode switch, or press the
“HW RST” (Hardware Reset) button on the circuit
board. The use of this button is further described
in the “ADVANCED FEATURES” section of this
manual.
These option switches are very small and should
be moved carefully using objects such as: eyeglass
screwdriver, fine-point pen, toothpick, or similar.
The listing below describes the available choices
for each option switch:
1
SWITCH #1 (SYSTEM): [OFF/RIGHT = FURN, default] This setting is used for the
majority of all heating systems that are not heat pumps. Examples for this
setting would be: natural gas furnace, hot water baseboard heat, and oil heat.
[ON/LEFT = HP] Use this setting if you have a heat pump unit (which looks just
like an outside air conditioning unit, but is used for both cooing and heating).
SWITCH #2 (TYPE): [OFF/RIGHT = PROG, default] The thermostat controls the
room temperature by following temperature program periods that you set up
based upon your daily routine. [ON/LEFT = MAN] The thermostat operates
manually just like a mechanical or non-programmable model. This method of
operation is very basic and only shows the room temperature and set
temperature; there are no temperature programs, days of the week, or clock
times.
SWITCH #3 (PERIODS): [OFF/RIGHT = 4, default] The thermostat uses four
temperature program periods in both heating and cooling (MORN, DAY, EVE, and
NITE). Each period has a separate start time and a set temperature. [ON/LEFT =
2] The thermostat operates in the same manner as above, however there are only
two temperature program periods for heating and cooling (DAY and NITE). This
may be more convenient if you are typically home during the day, and only need
the set temperature to be different while you are sleeping.
18
SWITCH #4 (SCALE): [OFF/RIGHT = F, default] All temperature values are
displayed using the Fahrenheit scale. [ON/LEFT = C] This setting displays all
temperature values using the Celsius scale.
SWITCH #5 (TIME): [OFF/RIGHT = 12 HR, default] This setting displays the clock
times and temperature program period start time values on the screen using US
standard AM and PM values. [ON/LEFT = 24 HR] This setting displays the clock
and temperature program period start time values on the screen using the 24 HR
military-time format (17:30 hours, 22:00 hours, without using AM/PM).
SWITCH #6 (DELAY): [OFF/RIGHT = 5 MIN, default] This sets the minimum length
of time that Heat or Cool must remain either On or Off, before it will
automatically switch to the alternate On or Off state. This internal delay prevents
rapid cycling of your system and provides equipment protection particularly for
cooling units. The 5-minute setting is fine for most applications. [ON/LEFT = 2
MIN] If you feel that your system may need to cycle more frequently than the
thermostat is allowing, then you may use the 2-minute setting.
SWITCH #7 (RECOVERY): [OFF/RIGHT = DISABLE, default] The Early Recovery
feature affects how the thermostat transitions from an energy saving setback
(DAY and NITE) program period, to a comfort (MORN and EVE) program period
temperature, when it is following the daily temperature programs. When this is
disabled, the thermostat makes a set temperature change at the beginning of an
upcoming period's start time. [ON/LEFT = ENABLE] The Early Recovery feature
will calculate the capability of your system and turn on the heating or cooling
early so that the temperature in your home reaches the desired set point as close
as possible to the start of the period. During the time that the thermostat is
performing a recovery, the words “IN RECOVERY” will be shown, alternating at
the top of the display with the current system mode.
19
GAS / ELEC SLIDE SWITCH (FAN OPERATION):
This switch is a physical component by itself on the
circuit board, and is much larger than the DIP
switches listed above.
BATTERY
[UP = GAS, default] This setting lets the heating
system control the blower fan automatically by
itself. Systems that would typically use the “GAS”
setting would be: natural gas, propane, or oil
furnaces. This setting has no effect upon Cool
mode operation.
GAS
ELEC
[DOWN = ELEC/HP] This setting runs the system’s blower fan when heat is called
for, and is required for heating systems that do not control their own fan while
the thermostat is in HEAT mode. Heat pump systems, and units with an electric
heating element typically require this setting.
COMPLETE THE INSTALL:
Once the hardware options are set, install two new Energizer® or DURACELL®
"AA" size alkaline batteries. Ensure that the batteries are installed in the proper
direction as per the markings shown in the battery tray. If the batteries were
already installed before changing the hardware setup options, change the
position of the HEAT/OFF/COOL System Mode switch to accept the new hardware
option switch settings.
FRONT PANEL ITEMS:
These two items below are both located on the right side of the thermostat
housing.
HEAT / OFF / COOL, SYSTEM MODE SWITCH: Set this switch to HEAT to control
your heating system, and COOL to control your cooling system. The OFF position
will disable both the heating and cooling units.
AUTO / ON, FAN MODE SWITCH: When this switch is in AUTO, the blower fan (if
present in your system) will automatically cycle on and off by itself while heating
or cooling is running. When in the ON position, the blower fan will run constantly
with or without a demand for heating or cooling, even when the System Mode
switch is in the OFF position.
20
NOTE: The Fan Mode switch only works if your system provides a wire for the
thermostat’s “G” wire terminal, to control a blower fan. The Fan Mode switch
has no effect in systems that do not have a blower fan (such as a hot water
radiator system).
OPERATING INSTRUCTIONS:
TOUCHSCREEN MENU CONTENTS:
• SET DAY/TIME
• SET/REVIEW “HEAT/COOL” PROGRAMS (not present in OFF mode)
• SET/REVIEW FILTER USAGE
• REVIEW “HEAT/COOL” ENERGY USAGE (not present in OFF mode)
• SET/REVIEW SWING VALUE
• SET KEYBOARD LOCK CODE (not present in OFF mode)
• SET “HEAT/COOL” TEMPERATURE STOP (not present in OFF mode)
• TEMPERATURE SETBACK (not present in OFF mode)
SET DAY AND TIME: Press the MENU button. The first menu item shown is “SET
DAY/TIME”, press the OK button. With the day flashing, press UP or DOWN to set
the day of the week. Press NEXT and the clock time will start flashing. Use UP
or DOWN to set the time, making sure the AM/PM indication is correct. Holding
the UP or DOWN buttons will make the clock digits scroll rapidly. Press the EXIT
button to return to the Normal Run screen.
HEATING AND COOLING: Basic operation of your heating or cooling system can
be obtained by choosing either HEAT or COOL on the System Mode switch. Touch
the Set Temperature digits on the screen and they will begin to flash. While they
are flashing, the UP and DOWN buttons will be shown also, which you can use to
adjust the current Set Temperature. When the thermostat is first powered up, it
will follow a default temperature routine that is preset from the factory (shown
below), until the clock has been set.
21
PERIOD
HEAT MODE
COOL MODE
MORN 6:00 AM 70 °F (21 °C) 6:00 AM 78 °F (26 °C)
DAY
EVE
8:00 AM 62 °F (17 °C) 8:00 AM 82 °F (28 °C)
6:00 PM 70 °F (21 °C) 6:00 PM 78 °F (26 °C)
NITE 10:00 PM 62 °F (17 °C) 10:00 PM 75 °F (24 °C)
There are on-screen indicators to show you when the thermostat is calling for
heating or cooling to occur. In the Heat mode switch position, a flame will be
present on the screen. A steady flame means that the thermostat is not calling
for your heating system to run, while a flashing flame means that your heating
system should be currently running. In the Cool mode switch position, a
snowflake will be present on the screen. A steady snowflake means that the
thermostat is not calling for your cooling system to run, while a flashing
snowflake means that your cooling system should be currently running.
EMERGENCY HEAT: (Heat Pump Configuration Only).
While in normal Heat mode, one single press of the
EMER button will activate Emergency Heat mode.
While in Emergency Heat, the top of the screen will
change from “Heat Mode” to show “Emer Heat”, and
EMER. = ON
an additional bold frame will appear around the EMER
button. A single press of the EMER button again will
end Emergency Heat, and return back to normal Heat
mode. If a power loss occurs while in Emergency Heat
mode, the thermostat will continue to remain in
EMER. = OFF
Emergency Heat mode even after the power comes
back on.
Emergency Heat mode will prevent the first stage of your heat pump system from
turning on, and use only the “W2” heat terminal (Auxiliary Heat) as the primary
heating source. This will not only prevent the heat pump from wasting energy if
outdoor temperatures are too low to support efficient operation, but it could also
prevent damage to the heat pump if outside temperatures are below the
manufacturer’s recommendations. As every heat pump has different operating
characteristics, you should refer to your heat pump literature to determine when
to disable the heat pump and run in Emergency Heat mode.
22
LCD DISPLAY BACKLIGHT: The display screen is lighted to assist viewing at
nighttime, or in locations with low light levels. A press of any area on the touch
panel will light the display for approximately 10 seconds. Any screen presses
that occur while the light is on will reset the 10-second timer, causing the screen
to remain illuminated for an additional 10 seconds.
TEMPERATURE OVERRIDE: While in the Normal Run screen, the set temperature
can be temporarily changed by pressing the Set Temperature digits, then
pressing the UP or DOWN buttons. The set temperature will return to the
programmed value stored in memory when the start time of the next upcoming
program period is reached (Morn, Day, Eve, Nite). While a Temporary Override is
in effect, the words “HEAT OVRRIDE” or “COOL OVRRIDE” will be shown in the
display screen. An Override may be cancelled by either pressing the HOLD
button two times, or by moving the mode switch to OFF, pausing briefly, then
switching back to the HEAT or COOL position. When in the Normal Run mode, the
display should say either “HEAT MODE” or “COOL MODE”.
MINIMUM RUN TIME: The thermostat has a default internal time delay of 5
minutes between load-on and load-off activations to prevent heating or cooling
system damage, which can occur from very frequent cycling. If heating or
cooling does not turn on right away with a manual change in set temperature,
please wait at least 5 minutes and the system should resume normal operation.
TEMPERATURE HOLD: A Temperature Hold is used for
maintaining a fixed set temperature. Once a Hold is
initiated, the thermostat will maintain the set
temperature indefinitely. A Hold may be used for
days, weeks, or even months at a time, as long as the
HOLD = ON
thermostat has adequate power. To enter Hold mode:
press the HOLD button one time and the words “HEAT
HOLD” or “COOL HOLD” will appear in the display, and
an additional bold frame will appear around the HOLD
button. To cancel a Hold, press the HOLD button one
HOLD = OFF
more time. If a mains power failure occurs during a
Temperature Hold, the thermostat will continue to
remain in Hold mode even after the power comes back on.
NOTE: If you plan to leave the thermostat in Hold mode for an extended duration
(unattended), it is advisable to install new Energizer® or DURACELL® "AA" size
alkaline batteries prior to leaving to ensure reliable operation of your heating and
cooling system.
23
STATIC NOTICE: This thermostat is protected against normal static electric
discharges, however to minimize the risk of damaging the unit in extremely dry
weather, please touch a grounded metal object before touching your thermostat.
TEMPERATURE PROGRAMS:
By default, this thermostat has 4 separate program periods for both Heat and
Cool mode, they are: MORN, DAY, EVE, and NITE. Each period ends at the start
time of the following period. The heat programs are set in HEAT mode, and the
cool programs are set in COOL mode.
NOTE: If the thermostat is configured to use only 2 periods per day instead of 4
(HARDWARE SETUP OPTIONS), the thermostat will only use the DAY and NITE
periods. The MORN and EVE periods will not be visible on the screen.
The following examples are shown using Heat mode. Programming in Cool mode
is done in the same exact manner with the System Mode switch in the Cool
position.
SET TEMPERATURE PROGRAMS: Press the MENU button, then press the SCROLL
button until “SET/REVIEW HEAT PROGMS” is shown, then press the OK button to
enter the programming screen. Use the UP and DOWN buttons to adjust the start
time for the MORN period, then press the NEXT button to advance. Use the UP
and DOWN buttons to adjust the set temperature for the MORN period, then press
the NEXT button to advance. Now adjust the start time and set temperature for
the DAY period, pressing the NEXT button after each to advance. Continue with
these same steps to adjust the start times and set temperatures for the EVE and
NITE program periods.
When the NITE period is finished the thermostat will advance to Tuesday, with the
MORN period start time flashing. Perform the same steps that you used for
setting the Monday periods, pressing the NEXT button to advance through each
flashing value.
PROGRAM COPY FEATURE: The Copy feature allows you to copy all of the
program information from any one single day, to any other day of the week. To
copy heat programs, the thermostat must be in Heat mode, and to copy cool
programs, the thermostat must be in Cool mode. Emergency Heat (heat pump
configurations only) uses the Heat temperature program. While in a temperature
programming screen, press the “COPY” button one time. The words “COPY
PROGRAM” will flash briefly at the top of the screen, followed by “FROM” and
“TO”. Under the word “FROM” will be a flashing day of the week. Using the UP
24
and DOWN buttons, select the day that you want to copy from. Press the NEXT
button one time. Your copy from day should now be on steady with the day under
the word “TO” flashing. Use the UP and DOWN buttons to select the day that you
would like to copy to. A single short press of the COPY button will perform the
copy, and the day flashing under the word “TO” will have advanced to the next
following day. You may continue to perform short single presses of the COPY
button to keep copying from the original source day to the remaining days, one
after the other. Specific days may be skipped by pressing the UP button, to
advance past them while they are flashing under the word “TO”. Press the EXIT
button to return to the Normal Run screen.
ADVANCED FEATURES:
TEMPERATURE SWING SETTING, OFFSET SETTING, AND TEMPERATURE
CALIBRATION:
NOTE: The Swing setting, Offset setting, and Calibration settings need to be
performed in a timely manner, as the thermostat will timeout and automatically
exit these adjustment screens after approximately 10 seconds without a button
press.
SWING DESCRIPTION: A thermostat works by turning your heating or cooling
system on and off whenever the room temperature varies from the desired set-
point temperature. The amount of this variation is called the Swing. Generally
your system should cycle on about 3 to 6 times per hour. A smaller swing
number makes the system cycle more frequently, so the room temperature is
more precise and constant. A larger swing number will make the system remain
on for a longer duration each time and decreases the number of cycles per hour.
There is only one Swing setting, and this determines the cut-in and cut-out
points for both the first and second stages (if present), in both Heat mode and
Cool mode. The swing setting range is between #1 and #9 (0.25°F to 2.25°F, in
0.25°F degree increments (or 0.14°C to 1.25°C, in 0.14°C degree increments for
Celsius)). Swing number 1 is the default setting.
OFFSET DESCRIPTION: This setting is shown as a number of degrees, and is
similar in nature to the Swing however this only effects the operation of the
second (auxiliary) heating stage, if present. The setting range for Offset is from
0°F to 9°F degrees (0°C to 5°C degrees). When set to 0 degrees, the second
heating stage is completely disabled while in regular Heat mode (Emergency Heat
mode will still function for heat pump configurations). The Offset value will
determine the number of degrees from the set point that will be required for the
25
second heating stage to turn on. This setting can be used to conserve energy in
situations where the second heating stage is more costly to operate when
compared to the first stage.
71
70
69
68
67
66
Cut-In / Cut-Out
(1st Stage)
70˚F Set
Temperature
Swing
Setting=
#2 (+/- 0.5˚F)
Offset **
Setting=
4˚F degrees
(2nd Stage) **
Cut-In / Cut-Out
65
DEGREES (F)
** = Only applies if a second
heat stage is present
26
TEMPERATURE CALIBRATION DESCRIPTION: The internal temperature sensor in
this thermostat is accurately calibrated at the factory, and in most cases,
alterations to this setting should not be needed. The Temperature Calibration
feature allows you to manually offset the measured temperature by as much as
plus or minus 5°F (3°C) degrees from its original value. This feature can be
useful to match or synchronize this thermostat to another one or more, if multiple
thermostats are used in the same home.
TO CHANGE THE SWING, OFFSET, AND CALIBRATION: Press the MENU button, then
press the SCROLL button until “SET/REVIEW SWING VALUE” is shown on the
screen, then press the OK button. The words “ADJUST VALUE SWING” will appear
at the top of the screen, along with a single flashing digit. Use the UP and DOWN
buttons to change the number value from #1 to #9. Press the NEXT button to
accept the Swing setting and proceed to the Offset setting.
After the Swing value has been accepted, the words “ADJUST VALUE OFFSET” will
appear at the top of the screen, along with a single flashing temperature digit.
Use the UP and DOWN buttons to change the number value between 0°F and 9°F
degrees (0°C to 5°C). The 0° (zero) degree setting will disable the 2nd heating
stage while in regular Heat mode. Press the NEXT button to accept the Offset
setting and proceed to the Calibration setting.
After the Offset value has been accepted, the words “ADJUST VALUE CAL” will
appear at the top of the screen, along with a single flashing temperature digit.
Use the UP and DOWN buttons to change the number value between –5°F and
+5°F (–3°C and +3°C). The 0° (zero) degree setting is the default value, and will
not alter the displayed room temperature from the measured reading. Press the
NEXT button to accept the Calibration setting and return back to the Swing
setting. You can keep pressing the NEXT button to review your three setting
values, or press the EXIT button to return to the Normal Run screen.
SETBACK FEATURE: The setback feature is similar to both a Temperature
Override and a Temperature Hold, in that both are used to maintain a fixed set
temperature instead of following a programmed daily routine. A Setback can be
considered the same as a Temperature Override, which can last for a longer
duration that you can adjust from 1-12 hours, or 1-30 days. By default, when a
Setback is activated in Heat mode, the set temperature used will be 5F (3C)
degrees lower than the current set temp. For Cool mode, the set temperature
used will be 5F (3C) degrees higher than the current set temp.
27
NOTE: The Setback settings need to be performed in a timely manner, as the
thermostat will timeout and automatically exit these adjustment screens after
approximately 10 seconds without a button press.
TO START A SETBACK: Press the MENU button, then press the SCROLL button
until “TEMPERATURE SETBACK” is shown, then press the OK button. The words
“OVERRIDE LEFT” will appear at the top of the screen, along with two digits and
the word “HRS”. Use the UP and DOWN buttons to set the duration for how long
you would like to maintain a fixed set temperature (from 1 to 12 hours). If you
would like to set the duration for longer than 12 hours, keep pressing the UP
button. The display will change from “HRS” left to “DAYS” left, with an available
duration of 1 to 30 days. Once you have selected your desired Setback duration,
press the NEXT button to advance. The display will change from “OVERRIDE
LEFT” left to “OVERRIDE TEMPERATURE”. Use the UP and DOWN buttons to select
your desired Set Temperature that will be used during the Setback duration.
Once complete, press the NEXT button to accept the setting and return to the
Normal Run screen.
TO CANCEL A SETBACK: A Setback can be cancelled by either pressing the HOLD
button two times, or by moving the mode switch to OFF, pausing briefly, then
switching back to the HEAT or COOL position. When in the Normal Run mode, the
display should say either “HEAT MODE” or “COOL MODE”.
TEMPERATURE LIMIT STOPS: There are two independent set temperature limit
stops: a maximum heat set temperature, and a minimum cool set temperature.
These stops do not prevent a user from performing normal actions like
Temperature Override or Hold. The Heat Limit Stop prevents the set temperature
from being adjusted higher than the heat limit setting. The Cool Limit Stop
prevents the set temperature from being adjusted lower than the cool limit
setting. Each of these temperature stops is user adjustable in one-degree
increments, and these settings are protected by a selectable 2-digit code to
prevent unauthorized tampering. By default, this 2-digit code is “00”, and the
temperature stops can be used as-is with this code.
NOTE: The Temperature Limit Stop settings need to be performed in a timely
manner, as the thermostat will timeout and automatically exit the setting screens
after approximately 10 seconds without a button press.
28
The following examples are shown for setting the maximum set temperature for
Heat mode. Setting the Temperature Limit Stop for Cool mode is done in the
same exact manner with the System Mode switch in the Cool position, and
instead you will be setting the minimum set temperature for cooling. Once a
Temp Stop Lock Code has been selected, this same code is used for both Heat
and Cool temp stops.
TO SET THE TEMPERATURE LIMIT STOP: Press the MENU button, then press the
SCROLL button until “SET HEAT TEMP STOP” is shown, then press the OK button.
The words “ENTER CODE” and “TEMP STOP” will appear at the top of the screen,
along with two digits at the left. Use the UP and DOWN buttons to enter the
current Temp Stop Lock Code (“00” by default). Press the NEXT button to
advance. If the code entered does not match the current Temp Stop Lock Code,
the words “WRONG CODE” will flash briefly, and you may try to enter the correct
code again. If the current code has been entered correctly, you will have the
ability to change the desired Temp Stop Lock Code to something else. The words
“SET CODE” and “TEMP STOP” will appear at the top of the screen, along with
two digits at the left. Use the UP and DOWN buttons to enter the desired Temp
Stop Lock Code to be used, and press the NEXT button to advance.
The words “SET HEAT RANGE STOP” will appear at the top of the screen, along
with two large temperature digits in the middle. Use the UP and DOWN buttons
to adjust the desired maximum heat set temperature value (or minimum set
temperature value for Cool mode). Once complete, press the NEXT button to
accept the setting and return to the Normal Run screen.
29
KEYPAD LOCKOUT: You can lock the touch-panel buttons to prevent unauthorized
tampering of your thermostat settings.
NOTE: These keypad lock instructions need to be performed in a timely manner,
as the thermostat will timeout and automatically exit the keypad lock screens
and return to the Normal Run screen after approximately 10 seconds without a
button press.
TO LOCK THE KEYPAD: The System Mode switch must be in either the Heat or
Cool position. Press the MENU button, then press the SCROLL button until “SET
KEYBOARD LOCK CODE” is shown, then press the OK button. The words “ENTER
CODE” will appear at the top of the screen, along with four digits at the left.
Select a 4-digit code that you would like to use for locking the thermostat. Press
the UP and DOWN buttons to change each digit individually, using the NEXT
button to cycle through which digit is selected. Pressing the OK button will lock
the thermostat touch panel using the 4-digit code that is shown on the screen,
and return to the Normal Run screen with a padlock shown to confirm that the
thermostat is now locked.
TO UNLOCK THE KEYPAD: Press the padlock icon, and the words “UNLOCK
KEYBOARD?” will appear at the top of the screen. Press OK to proceed with
entering the unlock code (or press the EXIT button to cancel). The words “ENTER
CODE” will appear at the top of the screen, along with four digits at the left. You
will need to enter the proper unlock code that was used for initially locking the
thermostat. Press the UP and DOWN buttons to change each digit individually,
using the NEXT button to cycle through which digit is selected. With the correct
lock code entered on the screen, pressing the OK button will unlock the
thermostat. If the code entered does not match the current keypad lock code,
the words “WRONG CODE” will flash briefly, and you may try to enter the correct
code again.
AIR FILTER MONITOR: In most systems that use a blower fan and air ducts, there
is an air filter that is either replaceable or requires cleaning. The filter is usually
located in the air handler, where the blower fan is. This thermostat feature
assists you with keeping track of proper maintenance and/or periodic
replacement intervals for your system’s filter.
30
The Air Filter Monitor counts the duration of filter usage that has occurred, since
the last time the Filter Monitor has been reset. This feature is for information
purposes only, and does not affect the operation of your heating or cooling
equipment, or the thermostat. When the filter usage duration has expired, the
words “CHANGE FILTER” will appear at the top of the display screen, alternating
with the current DAY and PERIOD.
TO ACCESS FILTER INFORMATION: Press the MENU button, then press the SCROLL
button until “SET/REVIEW FILTER USAGE” is shown, then press the OK button.
The words “FILTER USAGE COUNT” will appear at the top of the screen, along
with the total number of hours that have elapsed since the last time the filter
counter was reset. Press the NEXT button to advance.
The words “FILTER USAGE RESET?” will appear at the top of the screen. To reset
the filter counter to the start of the current limit setting press the OK button.
Press the NEXT button to advance.
The words “ADJUST VALUE FILTER LIMIT” will appear at the top of the screen.
This shows the current setting value for how many filter run time hours can
elapse before showing “CHANGE FILTER” in the Normal Run screen. The
adjustment range for this setting is from 0 hours to 2000 hours, with 720 hours
as the default. A filter limit setting of 0 (zero) hours will disable the filter
monitor feature. Once complete, press the EXIT button to save all settings and
return to the Normal Run screen.
NOTE: Air filters are sold based upon how many days they are rated for. One day
of filter run time is actually considered only 8 hours (not a full 24, since your
heating and/or cooling system only runs for approximatly one third of the time).
For a “90-day” filter, use a limit setting of 720 hours should be used, and for a
“30-day” filter, a limit setting of 240 should be used.
ENERGY USAGE MONITOR: Your thermostat contains a timer, which records the
amount of “on-time” for your heating and cooling systems. There are three
records that can be displayed for both Heat and Cool modes:
1) The amount of system run time so far for today.
2) The amount of system run time for yesterday.
3) The total cumulative system run time since the timer was reset.
The Heat Energy Usage information is shown while the System Mode switch is in
the Heat position, and the Cool Energy Usage information is shown while the
System Mode switch is in the Cool position. The following examples are shown
31
for viewing the Energy Usage while in Heat mode. Viewing the Cool mode
information is done in the same exact manner in Cool mode.
TO VIEW THE ENERGY USAGE TIMERS: Press the MENU button, then press the
SCROLL button until “REVIEW HEAT ENERGY USAGE” is shown, then press the OK
button. The words “TODAYS ENERGY USAGE” will appear at the top of the screen,
along with the amount of heating system runtime (displayed as “HH:MM”, for
hours and minutes). Use the NEXT button to cycle between Today’s Usage,
Yesterday’s Usage, and the Total Cumulative Usage for heat mode. NOTE: For the
Total Cumulative Usage, the timer will record up to a maximum of 99 hours and
59 minutes, then the display will change to “HHHH” for hours only, without the
colon in the center.
Pressing NEXT after the Total Cumulative Usage will show the words “TOTAL
USAGE RESET?” at the top of the screen. Pressing OK at this screen will clear
the Heat Energy Usage timer, and start back at 0 (zero). Press the EXIT button to
return to the Normal Run screen.
HARDWARE RESET: The Hardware Reset button (labeled “HW
RST”) is a small round push button that is located towards the
HW
RST
right side of the circuit board, just below the battery holder.
Pressing this button will cause the LCD display screen to
become fully populated, the heating and cooling load relays to
cycle off, read the position of the Hardware Setup Option
switches, and will perform an internal system check of the thermostat
components. If your thermostat appears to be acting in an erratic manner,
pressing the Hardware Reset button may remedy this behavior. The temperature
programs are not erased when a hardware reset is performed, however the clock
will have to be changed to match the current day and time.
SOFTWARE RESET: The Software Reset button (labeled “SW
RST”) is a small round push button that is located towards the
SW
RST
right side of the circuit board, just below the battery holder. A
Software Reset is used to erase all heating and cooling
temperature programs, and any user-adjustable software
values such as: Swing, Offset, and Calibration, to their original
factory default values. To perform a Software Reset, press and hold the Software
Reset button for at least 5 seconds. The LCD display screen will become fully
populated, then return to normal. The thermostat will still retain the current day
and time even after a Software Reset has been performed.
32
COMPRESSOR PROTECTION BYPASS: This optional feature permits the installer
or service technician to temporarily disable the built in compressor protection
delays. This is most useful for diagnosing and testing the heating and cooling
systems after installation is complete, and should not be used during normal
operation. To activate this feature, start with the System Mode switch in either
the Heat or Cool positions, then change to the OFF position. Press and hold the
OK button for at least 5 second. The thermostat will give a single beep sound to
confirm that this feature has been activated. All compressor protection delays
(in all modes of operation) will be disabled for 5 minutes. After the 5-minute
duration has expired, the thermostat will return to normal operation
automatically.
BATTERY REPLACEMENT:
This thermostat is powered by two “AA” Alkaline batteries. The batteries should
be replaced AT LEAST once per year to ensure reliable operation (or sooner, if the
“LO-BATTERY” icon appears at the bottom of the display screen). The batteries
are located on the back of the thermostat, at the top of the circuit board. The
front portion of the thermostat can be removed from the back half by pulling
straight outwards on the top and bottom of the thermostat housing, at the large
indentations that are present in the center of the top and bottom edges.
When installing new batteries, we recommend using only brand new Energizer®
or DURACELL®, “AA” size alkaline batteries. Please observe the polarity
markings shown in the battery compartment to ensure proper installation. When
finished, line up the front of the thermostat to the base, and firmly press together
to securely latch the front and back halves together properly.
33
TECHNICAL ASSISTANCE:
If you have any problems installing or using this thermostat, please carefully and
thoroughly review the instruction manual. If you require assistance, please
contact our Technical Assistance department at 856-234-8803 during regular
business hours between 8:00AM and 4:30PM Eastern Standard Time, Monday
through Friday. You can also receive technical assistance online anytime day or
guides, answers to the most common technical questions, and also permits you
to email your questions to our technical support staff at your convenience.
LIMITED WARRANTY:
If this unit fails because of defects in materials or workmanship within three
years of the date of original purchase, LUX will, at its option, repair or replace it.
This warranty does not cover damage by accident, misuse, or failure to follow
installation instructions. Implied warranties are limited in duration to three years
from the date of original purchase. Some states do not allow limitations on how
long an implied warranty lasts, so the above limitation may not apply to you.
Please return malfunctioning or defective units to the location from which the
purchase was made, along with proof of purchase. Please refer to “TECHNICAL
ASSISTANCE” before returning thermostat. Purchaser assumes all risks and
liability for incidental and consequential damage resulting from installation and
use of this unit. Some states do not allow the exclusion of incidental or
consequential damages, so the above exclusion may not apply to you. This
warranty gives you specific legal rights and you may also have other rights,
which vary from state to state. Applicable in the U.S.A. and Canada only.
MERCURY WARNING AND RECYCLING NOTICE:
Mercury is considered to be a hazardous material. If this product is replacing a
thermostat that contains mercury in a sealed tube, contact your local waste
management authority for instructions regarding recycling and proper disposal.
It may be unlawful in your state to place it in the trash.
34
FAN
AUTO
ON
MENU
˚
F
PM
˚
F
SET
HEAT
OFF
COOL
Mt. Laurel, New Jersey 08054, USA
856-234-8803
35
|