S225 TWO-WAY
LOUDSPEAKER
USER’S MANUAL
INTRODUCTION
Thank you for choosing the Mackie S225 sound rein-
forcement loudspeakers.
Connecting and setting up the S225 is a breeze. It
accepts a speaker-level signal via either a Neutrik
Speakon connector or female 1/4-inch TS (Tip/Sleeve)
®
The S225 is a professional two-way loudspeaker
system, designed to complement our professional pow-
ered mixers and power amplifiers. They are capable of
extremely high sound pressure levels, and designed to
give you the best performance of any loudspeaker in its
class and price range.
connector.
The cabinet is constructed using both 18 mm multi-
layer plywood and pressure injected structural resin.
A carrying handle is integrated into each side for easy
loading and transport.
The S225 features two 15-inch high-power low-fre-
quency woofers and a 1.75-inch titanium diaphragm
high-output compression driver. The woofers incoporate
technology used in large-format touring systems and,
with a precision 2.5-inch high-temperature voice coil, is
virtually indestructible.
CONTENTS
IMPORTANT SAFETY INSTRUCTIONS .................................................................................................2
INTRODUCTION ........................................................................................................................................3
HOOKUP DIAGRAMS ...............................................................................................................................4
Quick-Start........................................................................................................................................................................... 4
CONNECTIONS ......................................................................................................................................... 6
PLACEMENT ............................................................................................................................................... 6
Room Acoustics .................................................................................................................................................................. 6
SERVICE INFORMATION ......................................................................................................................... 8
Warranty Service ............................................................................................................................................................... 8
Troubleshooting ................................................................................................................................................................ 8
Repair .................................................................................................................................................................................... 8
CARE AND MAINTENANCE .................................................................................................................... 9
S225 SPECIFICATIONS .............................................................................................................................. 9
S225 LIMITED WARRANTY ....................................................................................................................11
Don’t forget to visit our website at www.mackie.com
for more information about this and other Mackie products.
3
Part No. 0013880 Rev. B 06/05
©2004-2005 LOUD Technologies Inc. All Rights Reserved.
HOOKUP DIAGRAMS
2. Connect the “Speaker Output” from your power
amplifier (or powered mixer) to the INPUT connec-
tor on the S225.
Quick-Start
Make all initial connections with the
power switches OFF on all equip-
ment. Make sure all master volume,
level, or gain controls are all the way
down.
3. Turn on your mixing console (or other signal
source).
4. Turn on the amplifier. Turn up its volume or gain
control(s) as recommended by the manufacturer.
1. Connect the line-level outputs from your mixing
console (or other signal source) to the inputs of
your power amplifier.
5. Start the signal source, whether it be speaking
into a microphone or starting a CD player. Adjust
the volume controls on the mixer (or other signal
source) for normal operation.
S225
S225
S225
S225
DESIGNED BY MACKOIDS IN WHITINSVILLE, MA
&
WOODINVILLE, WA,USA
DESIGNED BY MACKOIDS IN WHITINSVILLE, MA
&
WOODINVILLE, WA,USA
"MACKIE" AND THE "RUNNING MAN" FIGURE
"MACKIE" AND THE "RUNNING MAN" FIGURE
ARE REGISTERED TRADEMARKS OF LOUD TECHNOLOGIES INC.
•
COPYRIGHT ©2004
ARE REGISTERED TRADEMARKS OF LOUD TECHNOLOGIES INC. COPYRIGHT ©2004
•
Stereo
Power Amplifier
SERIAL NUMBER
MANUFADATE
SERIAL NUMBER
MANUFACDATE
Left
Line-level
Output
Right
Line-level
Output
1202-VLZPRO
Mixer or
Preamplifier
S225: WITH A MIXER AND POWER AMPLIFIER
S225
S225
S225
S225
Stereo Power Amplifier
Stereo Power Amplifier
From LEFT
From RIGHT
SPEAKER OUT
SPEAKER OUT
Line-level
THRU Connection
From LEFT
From RIGHT
SPEAKER OUT
SPEAKER OUT
1202-VLZPRO
S225: WITH A MIXER AND TWO POWER AMPLIFIERS
4
S225
S225
S225
S225
S225
S225
S225
S225
DESIGNED BY MACKOIDS IN WHITINSVILLE, MA
&
WOODINVILLE, WA,USA
DESIGNED BY MACKOIDS IN WHITINSVILLE, MA
&
WOODINVILLE, WA,USA
DESIGNED BY MACKOIDS IN WHITINSVILLE, MA
&
WOODINVILLE, WA,USA
DESIGNED BY MACKOIDS IN WHITINSVILLE, MA
&
WOODINVILLE, WA,USA
"MACKIE" AND THE "RUNNING MAN" FIGURE
"MACKIE" AND THE "RUNNING MAN" FIGURE
"MACKIE" AND THE "RUNNING MAN" FIGURE
"MACKIE" AND THE "RUNNING MAN" FIGURE
ARE REGISTERED TRADEMARKS OF LOUD TECHNOLOGIES INC.
•
COPYRIGHT ©2004
ARE REGISTERED TRADEMARKS OF LOUD TECHNOLOGIES INC.
•
COPYRIGHT ©2004
ARE REGISTERED TRADEMARKS OF LOUD TECHNOLOGIES INC.
•
COPYRIGHT ©2004
ARE REGISTERED TRADEMARKS OF LOUD TECHNOLOGIES INC. COPYRIGHT ©2004
•
SERIAL NUMBER
MANUFADATE
SERIAL NUMBER
MANUFAG DATE
SERIAL NUMBER
MANUFAG DATE
SERIAL NUMBER
MANUFG DATE
Stereo
Power Amplifier
Left
Right
Line-level
Output
Line-level
Output
1202-VLZPRO
Mixer or
Preamplifier
S225: WITH A MIXER AND POWER AMPLIFIER, USING THE 1/4" THRU JACKS
S225
S225
Mackie M•1400 Power Amplifier
Subwoofer Mode
S218s
S218s
Line-level
THRU Connection
Stereo Power Amplifier
From LEFT
From RIGHT
SPEAKER OUT
SPEAKER OUT
1202-VLZPRO
The S225s can be used with the Mackie S218s subwoofers to create an incredibly powerful
system. The FR Series M•1400 power amplifiers have a built-in subwoofer crossover. If you are not
using a Mackie M•1400 amplifier, you can use an active crossover between the first and second
amplifiers with the crossover set between 125 Hz to 180 Hz. This allows more amplifier power for
the low frequencies rather than being wasted as heat in the S218s’ internal built-in crossover.
S225: WITH A MIXER, TWO POWER AMPLIFIERS, AND TWO S218S SUBWOOFERS
5
CONNECTIONS
PLACEMENT
The S225 has two connectors labeled IN/OUT. One is a
The S225 speaker is designed to sit on the floor or
Neutrik Speakon™ connector and the other is a female stage.
1/4" TS connector. These connectors are wired in paral-
lel, and can be used either as an input from a power
amplifier, or as a “thru” connection for connecting the
input signal to another speaker’s input.
WARNING: The cabinet has no rig-
ging points and is not suitable for rig-
ging. NEVER attempt to suspend the
S225 by its handles. The S225 should
never be pole-mounted.
NEVER connect more than one
output from a power amplifier to the
S225 inputs.
You can create a horizontal array by placing the cabi-
nets side-by-side. However, you should have a good un-
derstanding of the relationship between the splay angle
(the angle between the facing sides of the cabinets),
the on-axis power, and frequency cancellation effects
between cabinets.
Keep in mind, when connecting two or more speakers
in parallel using the “thru” connections, that you want
to be sure not to go below the minimum impedance
requirements for your power amplifier.
When two cabinets are placed side-by-side, the actual
splay angle is 20º (determined by a 10º angle on each
cabinet side). As the splay angle increases toward the
angle of horizontal coverage (80º for the S225), the
on-axis power decreases, but the frequency response be-
comes smoother as the comb-filtering effects (caused by
the interaction in the area of double-coverage) decrease.
The S225 has a nominal impedance of
4 ohms.
Two S225s in parallel equals 2 ohms.
Three S225s in parallel equals 1.3 ohms.
Four S225s in parallel equals 1 ohm.
Use high-quality speaker cable as recommended by
the power amplifier manufacturer.
As with any powered components,
protect them from moisture. If you
are setting them up outdoors, make
sure they are under cover if you
expect rain.
DO NOT use coaxial shielded cable
like a guitar cord to make speaker
connections. They are not designed
to handle the high currents required
to drive a loudspeaker.
Room Acoustics
The Speakon connector is wired as follows:
Pin 1+ = Signal (“+” or hot)
Pin 1– = Ground (“–” or cold)
The S225 loudspeakers are designed to sound as neu-
tral as possible; that is, to reproduce the input signal as
accurately as possible.
1–
1+
Room acoustics play a crucial role in the overall per-
formance of a sound system. Here are some additional
placement tips to help overcome some typical room
problems that might arise:
COLD
1–
1+
2+
HOT
•
Avoid placing loudspeakers in the corners of a
room. This increases the low frequency output and
can cause the sound to be muddy and indistinct.
2–
Speakon Connectors
•
Avoid placing loudspeakers against a wall. This, too,
increases the low frequency output, though not as
much as corner placement. However, if you do need
to reinforce the low frequencies, this is a good way
to do it.
The 1/4" TS jack is wired as follows:
Tip = Signal (“+” or hot)
Sleeve = Ground (“–” or cold)
SLEEVE
SLEEVE
TIP
TIP
TIP
SLEEVE
1/4" TS Connectors
6
•
•
Avoid placing the speakers directly on a hollow
stage floor. A hollow stage can resonate at certain
frequencies, causing peaks and dips in the fre-
quency response of the room. It’s better to place the
loudspeakers on a sturdy table or stand designed to
handle the weight of the S225s.
Position the loudspeakers so the high-frequency
drivers are 2 to 4 feet above ear level for the audi-
ence (make allowances for a standing/dancing in
the aisles audience). High frequencies are highly
directional and tend to be absorbed much easier
than lower frequencies. By providing direct line-of-
sight from the loudspeakers to the audience, you
increase the overall brightness and intelligibility of
the sound system.
•
Highly reverberant rooms, like many gymnasiums
and auditoriums, are a nightmare for sound system
intelligibility. Multiple reflections off the hard walls,
ceiling, and floor play havoc with the sound. Depend-
ing on the situation, you may be able to take some
steps to minimize the reflections, such as putting
carpeting on the floors, closing draperies to cover
large glass windows, or hanging tapestries or other
materials on the walls to absorb some of the sound.
However, in most cases, these remedies are not
possible or practical. So what do you do? Making
the sound system louder generally doesn’t work
because the reflections become louder, too. The
best approach is to provide as much direct sound
coverage to the audience as possible. The farther
away you are from the speaker, the more prominent
will be the reflected sound.
Use more speakers strategically placed so they are
closer to the back of the audience. If the distance
between the front and back speakers is more than
about 100 feet, you should use a delay processor to
time-align the sound. (Since sound travels about 1
foot per millisecond, it takes about 1/10 of a second
to travel 100 feet.)
7
SERVICE INFORMATION
Repair
Warranty Service
Service for Mackie products is available at a factory-
authorized service center. Service for Mackie products
outside the United States can be obtained through local
dealers or distributors.
Details concerning warranty service are spelled out
on page 11 of this manual.
If you think your loudspeaker has a problem, please do
everything you can to confirm it before calling for service,
including reading through the following Troubleshooting
section. Doing so might save you from being deprived of
your Mackie loudspeaker.
If your S225 needs service, please follow these in-
structions:
1. Review the preceding troubleshooting suggestions.
Please.
Of all Mackie products returned for service (which is
hardly any at all), many are coded “CND” — Could Not
Duplicate— which usually means the problem lay some-
where else in the system. The following troubleshooting
tips may sound obvious, but here are some things you
can check:
2. Call Tech Support at 1-800-898-3211, 7 am to 5 pm
PST, to explain the problem in detail. They will ask
you all sorts of impertinent questions in the hope of
sorting out the problem. If it appears that the S225
needs repair, you will be given a Service Request
Number. Have your loudspeaker’s serial number
ready. You must have a Service Request Number be-
fore you can obtain service at a factory-authorized
service center.
Troubleshooting
3. Keep this user’s manual and the detachable line-
No sound
cord. We don’t need them to repair the loudspeaker.
•
Are the level controls on the mixer or amplifier
turned all the way down? Follow the procedures in
the “Quick-Start” section on page 4 to verify that
all the volume controls in the system are properly
adjusted.
4. Pack the loudspeaker in its original packaging,
including protective wrap, endcaps, and box. This
is VERY IMPORTANT. When you call for the Service
Request Number, please let Tech Support know if
you need new packaging. Mackie is not responsible
for any damage that occurs due to non-factory
packaging.
•
•
Is the signal source working (and making union
scale)? Make sure the connecting cables are in good
repair and securely connected at both ends.
5. Include a legible note stating your name, shipping
address (no P.O. boxes), daytime phone number,
Service Request Number, and a detailed description
of the problem, including how we can duplicate it.
Make sure the mixer does not have a Mute on or a
Processor loop engaged. If you find something like
this, make sure the volume/gain is turned down
before disengaging the offending switch.
6. Write the Service Request Number in BIG
PRINT on top of the box. Product shipped with-
out the Service Request Number will be refused.
Poor bass performance
•
Check the polarity of the connections between the
mixer and the loudspeakers. You may have your
positive and negative connections reversed at one
end of one cable, causing one loudspeaker to be
out-of-phase.
7. Tech Support will tell you where to ship the loud-
speaker for repair. We suggest insurance for all
forms of cartage.
8. We’ll try to fix the loudspeaker within five business
days. Once it is repaired, we’ll ship it back the same
way in which it was received. This paragraph does
not necessarily apply to non-warranty service.
Poor sound
•
Is it loud and distorted? Make sure that you’re not
Note: You must have a sales receipt from an Autho-
rized Mackie Dealer to qualify for a warranty repair.
overdriving a stage in the signal chain. Verify that
all level controls are set properly.
•
Is the input connector plugged completely into the
jack? Make sure all connections are secure. It’s a
good idea to periodically clean all electrical con-
nections with a non-lubricating electrical contact
cleaner.
8
•
•
Avoid exposure to extreme cold (below freezing
temperatures). If you must operate the loud-
speakers in a cold environment, warm up the voice
coils slowly by sending a low-level signal through
them for about 15 minutes prior to high-power
operation.
CARE AND MAINTENANCE
Your Mackie loudspeakers will provide many years of
reliable service if you follow these guidelines:
Avoid exposing the loudspeakers to
moisture. If they are set up outdoors,
be sure they are under cover if you
expect rain.
Use a slighty damp cloth with a mild soap solution
to clean the cabinets. Only do this when the power
is turned off. Avoid getting moisture into any of the
openings of the cabinet, particularly where the driv-
ers are located.
S225 SPECIFICATIONS
Acoustic Performance
Physical Properties
Height
50.0 in/127.0 cm
19.1 in/48.5 cm
13.9 in/35.3 cm
18.1 in/46.0 cm
99.5 lb/45.1 kg
Floor mount only.
Frequency Range (–10 dB)
46 Hz–20 kHz
Frequency Response (–3 dB)
70 Hz–18 kHz
Horizonal Coverage Angle (–6 dB)
90º averaged 2 kHz to 10 kHz
Vertical Coverage Angle (–6 dB)
40º averaged 2 kHz to 10 kHz
Directivity Factor; DI (Q)
11.9 (15.6) averaged 2k Hz to 10 kHz
Sensitivity (1W/1m) 102 dB SPL
Max SPL long-term 132 dB @ 1m
Front Width
Rear Width
Depth
Weight
Mounting Methods
The S225 should never be pole-mounted.
The S225 cabinet has no rigging points and is
not suitable for flying. Never attempt to suspend
the cabinet by its handles.
Max SPL peak
Crossover Point
135 dB @ 1m
1300 Hz
Disclaimer
Since we are always striving to make our products better by in-
corporating new and improved materials, components, and manufac-
turing methods, we reserve the right to change these specifications
at any time without notice.
Input/Output
Input/Output Type
Neutrik Speakon™ and
female 1/4-in. TS jack
4 ohms
“Mackie” and the “Running Man” figure are registered trademarks
of LOUD Technologies Inc.
Input Impedance
Recommended Amplifier Power
700 watts rms continuous
2800 watts peak
All other brand names mentioned are trademarks or registered
trademarks of their respective holders, and are hereby acknowledged.
High-Frequency Section
Voice Coil Diameter 1.75 in/44 mm
Horn Exit Diameter 1.0 in/25 mm
Phase Plug
Optimized geometry
Diaphragm Material Titanium
Magnet Material
Ferrite
Low-Frequency Section
Need Help?
Number of Drivers
Woofer Diameter
2
You can reach a technical support representative
Monday through Friday
15.0 in/381 mm
Voice Coil Diameter 2.5 in/63 mm
Diaphragm Material Epoxy-reinforced cellulose
from 7 AM to 5 PM PST at:
Magnet Material
Ferrite
1-800-898-3211
Safety Features
or email us at: [email protected]
Input Protection
Dynamic protection for
compression driver
Construction Features
Basic Design
Material
Trapezoidal, 10º side angles
18 mm multi-layered plywood,
resin end caps
Finish
Wear-resistant textured black
PVC vinyl
©2004-2005 LOUD Technologies Inc.
All Rights Reserved.
Handles
Grille
One on each side, one top, one bottom
Perforated metal with weather-
resistant coating
9
S225 Frequency Response On-Axis
S225 Frequency Response On-Axis
110
100
90
80
70
20
100
1000
10000 20000
Frequency (Hz)
S225 Beamwidth vs. Frequency
S225 Directivity vs. Frequency
360
20
100
300
240
180
10
10
120
60
Horizontal / Vertical
0
1
0
20
100
1000
10000 20000
20
100
1000
10000 20000
Frequency (Hz)
Frequency (Hz)
S225 Dimensions
50.0 in/
13.9 in/
127.0 cm
35.3 cm
S225
PRECISION PASSIVE
D
E
S
I
G
N
E
D
B
Y
M
A
C
K
O
I
D
S
I
N
W
H
I
T
I
N
S
V
I
L
L
E
,
M
A
&
W
O
O
D
I
N
V
I
L
L
E
,
WA,USA
M
A
N
U
F
A
C
T
U
R
E
D
I
N
C
H
I
N
A
•
"
M
A
C
K
I
E
"
A
N
D
T
H
E
"
R
U
N
N
I
N
G
M
A
N
"
FIGURE
GH 20
A
R
E
R
E
G
I
S
T
E
R
E
D
T
R
A
D
EMARK
O
F
LOUD
TECHNOLO
G
I
E
S
I
N
C
.
•
C
O
P
Y
R
I
T
©
0
4
S
E
R
I
A
L
NU
M
B
E
R
MA
N
U
F
A
C
T
U
R
I
N
G
D
A
TE
PIN
PIN
1
IN
2
N/C
IN
/
OUT
IN
/
OUT
18.1 in/
46.0 cm
19.1 in/
48.5 cm
19.1 in/
48.5 cm
10
S225 LIMITED WARRANTY
Please keep your sales receipt in a safe place.
A. LOUD Technologies Inc. warrants all materials,
be repaired or replaced within thirty days of receipt. LOUD
Technologies and its authorized service centers may use
refurbished parts for repair or replacement of any product.
Products returned to LOUD Technologies that do not meet
the terms of this Warranty will be not be repaired unless
payment is received for labor, materials, return freight,
and insurance. Products repaired under warranty will be
returned freight prepaid by LOUD Technologies to any
location within the boundaries of the USA.
workmanship and proper operation of this product for a
period of two years from the original date of purchase. If
any defects are found in the materials or workmanship or if
the product fails to function properly during the applicable
warranty period, LOUD Technologies, at its option, will
repair or replace the product. This warranty applies only
to equipment sold and delivered within the U.S. by
LOUD Technologies Inc. or its authorized dealers.
B. Failure to register online or return the product
G. LOUD Technologies warrants all repairs performed
for 90 days or for the remainder of the warranty period.
This warranty does not extend to damage resulting from
improper installation, misuse, neglect or abuse, or to
exterior appearance. This warranty is recognized only if
the inspection seals and serial number on the unit have not
been defaced or removed.
registration card will not void the two-year warranty.
C. Service and repairs of Mackie products are to be
performed only at a factory-authorized facility (see D
below). Unauthorized service, repairs, or modification will
void this warranty. To obtain repairs under warranty, you
must have a copy of your sales receipt from the authorized
Mackie dealer where you purchased the product. It is
H. LOUD Technologies assumes no responsibility for the
necessary to establish purchase date and determine whether quality or timeliness of repairs performed by an authorized
your Mackie product is within the warranty period.
service center.
D. To obtain factory-authorized service:
I. This warranty is extended to the original purchaser and
to anyone who may subsequently purchase this product
within the applicable warranty period. A copy of the
original sales receipt is required to obtain warranty repairs.
1. Call Mackie Technical Support at 800/898-3211,
7 AM to 5 PM Monday through Friday (Pacific Time)
to get a Service Request Number. Products returned
without a Service Request Number will be refused.
J. This is your sole warranty. LOUD Technologies does
not authorize any third party, including any dealer or
sales representative, to assume any liability on behalf of
LOUD Technologies or to make any warranty for LOUD
Technologies Inc.
2. Pack the product in its original shipping carton. Also
include a note explaining exactly how to duplicate the
problem, a copy of the sales receipt with price and date
showing, and your return street address (no P.O. boxes
or route numbers, please!). If we cannot duplicate the
problem or establish the starting date of your Limited
K. THE WARRANTY GIVEN ON THIS PAGE IS THE SOLE
WARRANTY GIVEN BY LOUD TECHNOLOGIES INC.
Warranty, we may, at our option, charge for service time. AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS
AND IMPLIED, INCLUDING THE WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. THE WARRANTY GIVEN ON THIS PAGE
3. Ship the product in its original shipping carton,
freight prepaid to the authorized service center. The
address of your closest authorized service center will be
SHALL BE STRICTLY LIMITED IN DURATION TO TWO
given to you by Technical Support.
YEARS FROM THE DATE OF ORIGINAL PURCHASE
FROM AN AUTHORIZED MACKIE DEALER. UPON
EXPIRATION OF THE APPLICABLE WARRANTY PERIOD,
LOUD TECHNOLOGIES INC. SHALL HAVE NO FURTHER
WARRANTY OBLIGATION OF ANY KIND. LOUD
IMPORTANT: Make sure that the Service Request
Number is plainly written on the shipping carton.
E. LOUD Technologies reserves the right to inspect
any products that may be the subject of any warranty
claims before repair or replacement is carried out. LOUD
Technologies may, at our option, require proof of the
original date of purchase in the form of a dated copy
of the original dealer’s invoice or sales receipt. Final
determination of warranty coverage lies solely with LOUD
Technologies.
TECHNOLOGIES INC. SHALL NOT BE LIABLE FOR ANY
INCIDENTAL, SPECIAL, OR CONSEQUENTIAL DAMAGES
THAT MAY RESULT FROM ANY DEFECT IN THE MACKIE
PRODUCT OR ANY WARRANTY CLAIM. Some states do
not allow exclusion or limitation of incidental, special,
or consequential damages or a limitation on how long
warranties last, so some of the above limitations and
exclusions may not apply to you. This warranty provides
specific legal rights and you may have other rights which
vary from state to state.
F. Any products returned to one of the LOUD Technologies
factory-authorized service centers and deemed eligible for
repair or replacement under the terms of this warranty will
11
16220 Wood-Red Road NE • Woodinville, WA 98072 • USA
US and Canada: 800.898.3211
Europe, Asia, Central and South America: 425.487.4333
Middle East and Africa: 31.20.654.4000
E-mail: [email protected]
|