Owner's Manual
Mobile DVD/CD Player
with 10.2" TFT Monitor
Model: MV1020 / MV1020C
For operational or technical assistance, after reading this manual,
Use this Product Safely
Driving
Repairs
Be aware of road and traffic conditions. Keep
the volume at a low level.
Do not attempt to disassemble or repair this
product yourself. Contact our customer service
representatives.
Moisture
Do not expose the product to water or excessive
moisture. This could cause electrical shorts, fire
or other damage.
Installation
The unit should be installed in a horizontal posi-
tion (see pages 15-17).
Parking
Cleaning
Parking in direct sunlight can produce very high
temperatures inside your vehicle. Give the car
interior a chance to cool down before starting
disc playback.
Use a soft dry cloth to clean the screen. The
cloth can be dampened with purified water, but
do not use any cleaners or chemicals.
Warning
Proper Power Supply
Be careful not to drop or apply undue pressure
to the front panel of monitor. If the screen
cracks due to misuse, the warranty will be voided!
This product is designed to operate with a 12
Volt DC, negative ground battery system.
Protecting the Disc Mechanism
Avoid inserting any foreign objects into the disc
slot of this player. Failure to observe this pre-
caution may cause malfunction of this unit.
Features
• This unit can play compatible discs recorded in • Front Panel Controls.
either PAL or NTSC format.
• CD, DVD, CD-R, CD-RW and MP3 Compatible.
• SD Card Support.
• Full-Function Wireless Remote Controller.
• Multi-Language On-Screen Display Menu.
• Built-In Dome Light System.
• Wireless IR Transmitter Module so audio can be
heard through IR headphones.
•
Wireless FM Stereo Transmitter Module so audio
can be heard through the vehicle’s radio.
• L/R stereo analog audio outputs for connection
to existing head unit auxiliary inputs. Output is
composite video.
3
Disc and SD Card Notes
Disc Formats Supported by this Player:
Label side up
I
D
E
O
V
(Single-sided disc only)
8 cm disc
Do not touch
the underside
of the disc
8 cm disc
Discs which cannot be played with this player:
• DVD-ROM
• DVD-R/DVD-RAM
• CDV
Do not bend
• CD-G
Wipe the disc
from center
toward the
SD Card File Format Compatibility:
• AVI (Video)
outside edge.
• MP3 (Audio)
• JPEG (Pictures)
Disc Handling
• Dirt, dust, scratches on disc may cause mal-
functions.
• Do not place labels on disc.
• Do not warp discs.
• A disc should always be kept in its case when
not in use to prevent damage.
•
Do not place discs in the following places:
1. Direct sunlight.
2. Dirty, dusty and damp areas.
3. Near car heaters.
4. Car seats or dashboard.
Disc Cleaning
Use a dry soft cloth to wipe the surface. If the
disc is quite dirty, use a cloth slightly dampened
with isopropyl (rubbing) alcohol. Never use sol-
vents such as benzine, thinner or conventional
record cleaners as they may mar the surface of
the disc.
4
Screen and DVD/CD Functions
12
13
11
14
1
2
3
4
5
6
7
8
9
10
15
1. POWER Button: Press this button to turn the 10. EJECT Button: Press to eject the disc.
unit On/Off.
11. Disc Slot: To play a DVD/CD disc, insert into
2. SOURCE Button: Press this button to change
the play source between DVD/CD player and
an auxiliary input source.
slot with label facing forward.
12. Dome Lights
13. Dome Light Switch: Switch to the ON position
3. STOP Button: Stops play of picture or audio.
to activate the dome lights.
4. Power On LED Indicator
14. SD Card Slot: To play a SD Card, insert into
slot with label facing forward.
5. Infrared Remote Sensor: Receives the signals
from the remote control.
15. Viewing Screen Release: To release the
screen, push the tab then gently pull down
the screen. Place the screen to the desired
viewing position.
6. Wireless Transmitter Module: The audio sig-
nal is converted to an infrared light or FM fre-
quency and transmitted to the headphones or
vehicle’s FM stereo receiver.
7. PREVIOUS Button: In DVD/CD mode, press-
ing this button searches for the beginning of
the previous track or chapter.
8. NEXT Button: In DVD/CD mode, pressing this
button searches for the beginning of the next
track or chapter.
9. PLAY/PAUSE Button: Press this button to play
or pause a disc.
5
Screen and DVD/CD Functions
Turning the Unit On:
Inserting a SD Card
Press the POWER on either the remote or the
screen housing.
Label Side
Facing Forward
Adjusting the Monitor:
1. Press the MODE button on the remote to
activate the monitor adjustment menu. The
following will be displayed on the screen:
BRIGHTNESS
01/10
25
To play a SD card, insert a card into slot with
label side facing forward.
Selecting the SD Card Format
2. Press the MODE button again to select the
Once the SD card is inserted push the SD but-
ton on the remote. The screen will prompt you
to select the format for the inserted SD card.
Use the or button on the remote to select
the desired format. Once you have selected
the desired format press the ENTER button.
adjustment bar.
3. Use the UP and DOWN buttons on the
remote to adjust the screen’s brightness.
4. Press the MODE button again then the
DOWN button to select the next desired
monitor adjustment item:
• Saturation
Format Selection
• Contrast
• Hue
• FM (Wireless Transmitter Frequency)
• Rotate
1:Audio/Picture
2:Video File
• Source (DVD or AVIN)
• SD Card
Note: To go back to this selection screen,
press the STOP button twice and then press
the TITLE button.
• Reset (Reset to factory settings)
5. Press the MODE button again until the EXIT
item appears or wait 10 seconds and the
menu will automatically disappear.
Note: Large video files will take extra time to
Load/Buffer before video playback begins.
Inserting a DVD/CD
Changing to an Auxiliary Input Source
Label Side
Facing Forward
Press the SOURCE button to change the play
source between DVD/CD player and a Auxiliary
Input Source.
To play a DVD/CD, insert a disc into slot with
label side facing forward.
6
Screen and DVD/CD Functions
Wireless Transmitter Modules:
Infrared Remote Control Sensor:
Wireless
Transmitter
Modules
Optional IR Headphone:
HP-400
Vehicle’s FM Stereo
Receiver
The Infrared remote control sensor receives
the signals from the remote control.
The audio signal is converted to an infrared
light and FM frequency that is transmitted to
the IR headphones or the vehicle’s FM stereo
receiver.
Dome Light:
Selecting the Wireless Transmitter Frequency:
Dome Light Switch
1. Press the MODE button on the remote to
activate the monitor adjustment menu.
2. Use the UP and DOWN buttons on the
remote to select the FM screen.
FM
05/10
87.7 MHZ
To turn "On" the dome lights, press the dome
light switch. Press the dome light switch again
to turn them "Off".
3. Press the MODE button again to select the
frequency selection menu.
4. Use the UP and DOWN buttons on the
remote to select the desired frequency to
match the frequency on the wireless head-
phones or FM stereo receiver.
Note: The dome lights will automatically illu-
minate whenever the vehicle doors are open.
Last Play Function:
See page 14.
5. Press the MODE button again until the EXIT
item appears or wait 10 seconds and the
menu will automatically disappear.
7
Remote Control Locations and Operation
10. REV/FWD: Scan backward and forward.
13
14
11. SLOW:
Press the button to slow play
DVD to 1/2, 1/4, 1/8, 1/16, or
1/32 speed.
POWER
TITLE
SOURCE EJECT
1
2
3
4
5
6
7
12. SD:
To play a SD card, press this
button. The screen will prompt
you to select the format for
the inserted SD card. Use the
or buttons on the remote to
select the desired format. Then
press ENTER button.
15
16
AUDIO
ANGLE
1
4
2
5
8
0
3
6
SUBTITLE
DISPLAY
SETUP
7
9
13. TITLE:
Displays the DVD’s title.
17
18
SEARCH
10+
14. SOURCE:
Select DVD/CD, TV Tuner or
Auxiliary inputs functions.
PLAY/PAUSE MENU
STOP
15. EJECT:
Ejects the disc.
ENTER
19
20
21
16. 0 - 10+:
Press these buttons to input
numbers.
PROG
PREV
REV
CLEAR RETURN
8
9
NEXT
FWD
VOL–
ZOOM
PBC
VOL+
17. SEARCH:
Locate title, chapter, time and
play.
MODE
UP
10
18. MENU:
19. STOP:
Display DVD’s menu screen.
Stop play of picture or audio.
22
23
24
25
SLOW
SD
A-B
11
12
20. RETURN:
Press to return to previous
item.
REPEAT
MUTE
DOWN
TFT
21. VOL-/VOL+: Press these buttons to
decrease or increase volume
level.
FUNCTION
22. MODE:
Activate the monitor adjust-
ment menu.
1. POWER:
Turns the unit On/Off.
2. AUDIO:
Press the button to change audio
languages.
23. UP:
Press to adjust the monitor
menus.
3. ANGLE:
Press the button to change
DVD’s picture angle.
24. DOWN:
25. MUTE:
Press to adjust the monitor
menus.
4. SUBTITLE: Press the button to change
DVD’s subtitle languages.
Press during play to stop
audio.
5. DISPLAY: Press the button to display disc
information.
6. SETUP:
Press the button to enter or can-
cel SETUP MENU.
7. ENTER:
Press the button to enter a setting.
8. PROG:
Press the button to program the
play order of CD tracks.
9. PRE/NEXT: Press these buttons to search for
the beginning of track or chapter.
8
Remote Control Locations and Operation
BASIC OPERATION
POWER
TITLE
SOURCE EJECT
Turn the Unit On
1. Turn the car ignition on to the accessory
position.
2. Press the POWER button.
AUDIO
ANGLE
1
4
2
5
8
0
3
6
SUBTITLE
DISPLAY
SETUP
Loading a Disc
7
9
Insert the disc with printed side facing forward
into the disc slot. The player will automatically
search the disc.
SEARCH
10+
PLAY/PAUSE MENU
29
30
Volume Level Adjustment
Press the VOL or VOL buttons on the remote
to increase or decrease volume level.
STOP
+
26
-
ENTER
PROG
PREV
REV
CLEAR RETURN
Muting the Sound Level
NEXT
FWD
VOL–
ZOOM
PBC
VOL+
Press the MUTE button during play to stop
audio. Press the MUTE button again to restore
sound to the previous level.
MODE
UP
31
32
SLOW
SD
A-B
Ejecting a Disc
Press the EJECT button to eject disc.
27
28
REPEAT
MUTE
DOWN
TFT
FUNCTION
PLAY FUNCTION
Stopping Play
26.
Use CURSOR buttons when
selecting items or to move
cursor up, down, left or right.
Press the STOP button to stop the disc play-
back. Press the PLAY/PAUSE button on the
remote to continue with normal playback at the
position it was stopped. When the disc is
removed or STOP is pressed again, the resume
function is cancelled.
27. A-B:
Press the button during play
to set point A and point B,
then program A and B will be
played repeatedly. Press the
button again to cancel.
Pausing Play
28. REPEAT:
Press to select Chapter
Repeat, Title Repeat or Repeat
Cancelled.
Press the PLAY/PAUSE button to pause disc
during playback. Press the button again to
resume play.
29. PLAY/PAUSE: Press the button to play or
stop temporarily.
Clear numbers which have
been input.
Scan Forward and Backward
Press the REV or FWD button to scan back-
ward or forward.
30. CLEAR:
31. ZOOM:
Press the button during play-
back of DVD to enlarge an
area on the screen.
Return to Previous Chapter or Track
Press the PREVIOUS or PREV button during
playback and the play returns to the beginning
of the previous chapter or track.
32. PBC:
Video disc playback control.
DVD’s subtitle languages.
9
Basic Operation and Special Functions
PLAY FUNCTION (Continued) DVD SPECIAL FUNCTIONS
Slow Play
Advance to Next Chapter or Track
Press the NEXT button during playback and the
play advances to the beginning of the next
chapter or track.
Each time the SLOW button is pressed during
DVD play the speed is reduced as follows:
Normal Playback Pause 1/2 1/4 1/8 1/16 1/32
Removing Disc
Press the STOP button, then press the EJECT
button to eject the disc.
Display DVD Menu Screen
1. Press the MENU button to display the DVD
menu screen.
2. Use the cursor button to select item.
3. Press ENTER or PLAY to play the selected.
Searching for a Specific Chapter or Track
1. Press the SEARCH button on the remote.
2. Press numerical key to select track, chapter
or time.
3. Press ENTER or PLAY to play the selection.
ANGLE
POWER
TITLE
SOURCE EJECT
4
5
8
0
6
AUDIO
ANGLE
SUBTITLE
DISPLAY
SETUP
2
1
1
4
2
5
8
0
3
6
7
9
SEARCH
10+
SUBTITLE
DISPLAY
SETUP
PLAY/PAUSE MENU
7
9
2
3
3
STOP
SEARCH
10+
ENTER
PLAY/PAUSE MENU
PROG
CLEAR RETURN
1
STOP
ENTER
PROG
CLEAR RETURN
Repeat Play
For DVD’s, press the REPEAT button to repeat
title or chapter.
View Angles of DVD
Press the ANGLE button to select the different
angles to view.
Note: If the DVD doesn’t have multi-angle func-
tion, this function isn’t applicable.
For CD’s, press the REPEAT button to repeat a
track or the entire disc.
For MP3’s, press the REPEAT button to repeat
file, directory or all.
A-B Repeat
DVD Zoom
Press the A-B button during play to set point A
then press again to set point B. The system will
repeatedly play the programmed section until
the A-B button is pressed again which cancels
the function.
Press the ZOOM button during playback of
DVD to enlarge an image area on the screen.
Note: In zoom mode, press the CURSOR buttons
to move image areas up, down, left or right.
10
Special Functions and Setup Menu
DVD SPECIAL FUNCTIONS (Continued)
SETUP MENU
1. Press the SETUP button on the remote con-
trol, and the setup menu will be displayed.
Pressing SETUP during disc play will pause
play. Play will resume when the setup screen
is cancelled.
Multi-Subtitle Language Function
Press the SUBTITLE button during playback.
Each time the button is pressed the subtitle
language on the screen changes.
2. Use the CURSOR buttons
to
Multi-Audio Language Function
select desired function.
3. Press the ENTER button to confirm the selection.
Press the AUDIO button during playback. Each
time the button is pressed the audio sound-
track language on the screen changes.
CD SPECIAL FUNCTIONS
Program CD Play
1. While the CD is playing push the STOP but-
ton twice (2x).
2. Use the CURSOR buttons to select the first
desired track. Then press ENTER button to
confirm. For additional tracks repeat Step 2.
3. Press PLAY button to start Program Play.
Descriptions of the Setup Menu Functions:
DISC - Disc Setting
VIDEO - Video Setting
AUDIO - Audio Setting
DISPLAY - OSD Language Setting
OTHERS - Other Functions Setting
Random CD Play
1. While the CD is playing push the STOP but-
ton twice (2x).
2. Push the PROG buttons twice (2x) to
bypass the programming screen.
3. “CD Random” will be displayed, then push
PLAY button to start Random CD Play.
Note:
•
If there is no disc in the player while in the
"DISC" setting menu, this function is not
applicable.
•
Press the RETURN button to go back to the
last setting. For example, if you input the
wrong password in the "PARENTAL LOCK"
function, press the RETURN button to
return to the last setting so the password
can be input again.
MP3 FUNCTION
This unit supports MP3 discs. Use the CURSOR
buttons to move the cursor through the MP3
directory. Then push ENTER to play desired
file.
Note: While a disc is playing, push the PREVI-
OUS (PREV) or NEXT button to play the previ-
ous or next file on the disc.
11
Setup Menu
DISC SETTINGS
Use the CURSOR buttons
DISC setting selections. Press the ENTER button
to confirm the setting.
to make
Menu Language Setting
Use this screen to setup the disc menu language.
Parental Lock Rating
Use this screen to setup the Parental Lock
Rating. This function helps restrict viewing
movies with certain ratings (e.g., PG-13, R,
etc.) as supported by each DVD.
Audio Setting
Use this screen to setup the audio language on
multi-language discs.
Subtitle Language Setting
Use this screen to setup the subtitle language
on multi-subtitle language discs.
Parental Lock Password Setting
Use this screen to setup a four-digit parental lock
password. On the remote control, use this NUMER-
IC keys to enter the password. Press the ENTER
button to confirm the password.
12
Setup Menu
AUDIO SETTINGS
VIDEO SETTINGS
Use the CURSOR buttons
VIDEO setting selections. Press the ENTER but-
ton to confirm the setting.
to make Use the CURSOR buttons
to make
AUDIO setting selections. Press the ENTER but-
ton to confirm the setting.
TV Aspect Setting
Use this screen to setup the desired TV
Aspect Ratio.
DISPLAY SETTINGS
Use the CURSOR buttons
OSD Language setting selections. Press the
to make
ENTER button to confirm the setting.
TV System Setting
Use this screen to select the TV system.
Choose between three modes: NTSC, PAL and
Auto.
OSD Language Setting
Use this screen to setup the desired OSD
Language.
13
Setup Menu
OTHER FUNCTION SETTINGS
Last Play Function
Use the CURSOR buttons
to make
The Last Play function automatically book-
marks the position on a DVD/CD disc and
remembers the playback settings. Playback
will resumes at the position which the player
was turned off, the disc was ejected, or the
power was cut off.
OTHERS setting selections. Press the ENTER
button to confirm the setting.
Turning Off Last Play Function
Press the SETUP button to display the main
menu. Then use the CURSOR buttons to
select the OTHERS menu, then LAST PLAY
and ON. Press the ENTER button to confirm
the setting.
JPEG Time Setting
Use this screen to setup the JPEG image dis-
play time from 1 to 180 seconds.
Default Settings
Use this screen to reset all menus to the fac-
tory default setting.
14
Installation
The MV1020 can be mounted using either a Custom Bracket System or a Custom Shroud/ Bracket
your vehicle.
Custom Bracket Mounting System (Optional)
Vehicle’s Ceiling Support Beams
When installing the MV1020 using
a Custom Bracket Mounting System
refer to the instructions included with
with the bracket.
Warning: Take extra care not to penetrate
the roof of your vehicle during installation.
Custom Shroud/Bracket Mounting System (Optional)
When installing the MV1020 using
a Custom Shroud/Bracket Mounting System
refer to the instructions included with
with the shroud/bracket.
Warning: Take extra care not to penetrate
the roof of your vehicle during installation.
15
Wiring Diagram
Audio Video Input (Female RCA)
Yellow (Video In)
White (L-Audio In)
Red (R-Audio In)
Mini DIN Connector
Audio Video Output (Female RCA)
Black (Video Out)
White (L-Audio Out)
Red (R-Audio Out)
Red Wire - Ignition
Black Wire - Ground
Yellow Wire - Battery
3A
Blue Wire - Door (+)
16
Wiring Instructions
Power Harness Wiring:
Black Wire: The black wire in the harness
should be connected to the chassis of the
vehicle using a ring terminal and self tap-
ping screw or bolt and nut.
The 4-wire harness provides battery and ignition
12 volts as well as a chassis ground. Route the
power harness to the point in the vehicle that
you will make the connections.
Red Wire: The red wire in the harness should
be connected to a +12 volt power wire that
is turned on and of by the position of the
ignition key.
Blue Wire: Connect to the common trigger
wire coming from all door pin switches (+).
Yellow Wire: The yellow wire in the harness
should be connected to a constant +12 volt
wire that is NOT turned on and off by the
position of the ignition key.
Specifications
Supply Voltage: 12V DC, Negative Ground
Current Consumption: 24 Watts Maximum
Fluorescent Dome Light: 3 Watts
Screen Format: 16:9
Resolution: 800 x 600 Pixels
A/V Input: 1
A/V Output: 1
IR Transmitter: Yes
FM Transmitter: Yes
Dimensions (mm): 310 (w) x 310 (d) x 48 (h)
17
Troubleshooting
Only qualified service personnel can remove No Sound:
the cover or service this player. Otherwise the
warranty will become invalid.
• Check audio connections.
• If using a Hi-Fi amplifier, try another sound
source.
No Power:
• Check to see if the player is set to “On”.
• Check to see that the power plug of the main
unit is properly connected.
Disc Does Not Play:
• Ensure the disc label is facing forward.
• Clean the disc.
• Check to see if that power to the outlet is
properly working.
• Check to see if the disc is defective by trying
another disc.
No Picture:
The Player Does Not Respond to the Remote
• Check to see that the monitor is switched to Control:
“On”.
• Aim the remote control directly at the sensor
• Check that the correct SOURCE is selected
(DVD or AV) by pushing the SOURCE button.
• Check the video connection.
on the front of the housing.
• Avoid all obstacles which may interfere with
the signal path.
• Inspect or replace the remote control batter-
ies.
Distorted Picture:
• Check the disc for fingerprints and clean with
soft dry cloth, wiping from center to edge.
• A small amount of picture distortion may
appear. This may not be a malfunction.
Buttons Do Not Work:
• Press POWER to turn “Off” the unit, then
press it again to turn “On” the unit.
Completely Distorted Picture:
The disc format is not according to the monitor
used (PAL/NTSC).
Volume different for DVD and CD:
• This is due to different recording methods
No Color in Picture:
The disc format is not according to the monitor
used (PAL/NTSC).
18
Replacement Parts Order Form
Send Orders To: Magnadyne Corporation
We Accept Checks, Money Orders, Visa and Master Card
ATTN: Consumer Parts Sales
Make Checks Payable to: Magnadyne Corporation
P.O. Box 5365
Carson, CA 90749-5365
SHIP TO: (No P.O. Boxes)
LAST NAME
FIRST NAME
INITIAL
STREET ADDRESS (IF PAYING WITH A CREDIT CARD, YOUR BILLING ADDRESS IS REQUIRED)
CITY
STATE
ZIP CODE
DAYTIME PHONE NUMBER
CREDIT CARD INFORMATION:
CARD TYPE:
VISA
MASTER CARD
CARD NUMBER
EXP. MONTH
YEAR
NAME - EXACTLY AS IT APPEARS ON YOUR CREDIT CARD
Part #
Description
Qty.
Price Each
$39.95
TOTAL
Remote Control
MV1020RM
Shipping and Handling
Subtotal = ________ . ______
Subtotal + Tax
Up to $20.00
20.01 to 30.00
30.01 to 45.00
45.01 to 70.00
Over 70.01
Add
$5.00
5.95
6.50
6.95
7.95
California Residents Add Sales Tax = ________ . ______
Shipping and Handling (See Chart) = ________ . ______
TOTAL = ________ . ______
No C.O.D.’s
On regular orders please allow 4-5 weeks for delivery. Please give a shipping address where this order
may be delivered between the hours of 9 a.m. and 5 p.m. weekdays. If UPS is unable to deliver, your order will be
returned and additional shipping charges will be required.
19
Order By Mail
Replacement Parts for MovieVision® Systems
DESCRIPTION
MODEL #
PRICE
1
4
2
5
8
0
3
6
9
7
10+
DVD Remote Control
MV-1020RM
$39.95 Ea.
Warranty
ONE (1) YEAR LIMITED WARRANTY
Magnadyne Corporation or its authorized agents will within 1 year from the date of sale to you, repair,
replace or refund the retail sales price of said product or any part thereof, at the option of the
Magnadyne Corporation or its authorized agents, if said product or part is found defective in
materials or workmanship, when properly connected and operating on the correct power
requirements designated for the specific product. This warranty and Magnadyne Corporation or its
authorized agents obligations hereunder do not apply where the product was; damaged while in the
possession of the consumer, subjected to unreasonable or unintended use, not reasonably
maintained, utilized in commercial or industrial operations, or serviced by anyone other than
Magnadyne Corporation or its authorized agents, or where the warning seal on the product is bro-
ken or the power and/or plugs are detached from the unit. Magnadyne Corporation or any of its
authorized agents will not assume any labor costs for the removal and re-installation of any product
found to be defective, or the cost of transportation to Magnadyne Corporation or its authorized
agents. Such cost are the sole responsibility of the purchaser.
This warranty does not cover the cabinet appearance items or accessories used in connection with
this product, or any damage to recording or recording tape, or any damage to the products resulting
from improper installation, alteration, accident, misuse, abuse or acts of nature.
MAGNADYNE CORPORATION OR ITS AUTHORIZED AGENTS SHALL NOT BE LIABLE TO ANYONE
FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES OR CLAIMS EXCEPT THOSE ACCORDED BY
LAW. NO EXPRESSED WARRANTY OR IMPLIED WARRANTY IS GIVEN EXCEPT THOSE SET FORTH
HEREIN. NO IMPLIED WARRANTY SHALL EXTEND BEYOND 1 YEAR FROM THE DATE OF SALE.
This warranty extends only to the original purchaser of the product and is not transferable.
Some states do not allow limitations on how long an implied warranty lasts and some states do not
allow the exclusion or limitation of incidental or consequential damages, so the above limitations or
exclusion may not apply to you. This warranty gives you specific legal rights and you may have other
rights that vary from state to state.
Defective merchandise should be returned to the original point of purchase or secondly, to
Magnadyne Corporation, 1111 W. Victoria Street, Compton CA 90220. Return Authorization must be
obtained before sending, or merchandise may be refused.
© Copyright 2007 Magnadyne Corporation
MV1020-UM Rev. A 1-2-07
|