R
DVI-9990
DVD-Audio/Video Tuner
Guide for Installation and Connections
Guide d’installation et de connexions
Guía de instalación y conexiones
English
Français
Español
Español
Italiano
Svenska
PRECAUTIONS
GUIDE FOR INSTALLATION AND CONNECTIONS
• Please read this GUIDE FOR INSTALLATION AND CONNECTIONS and the OWNER’S
MANUAL thoroughly to familiarize yourself with each control and function. We at ALPINE hope
that your new DVI-9990 will give you many years of listening enjoyment.
In case of problems when installing your unit, please contact your authorized ALPINE dealer.
Points to Observe for Safe Usage
• Read this manual carefully before starting operation and use this system safely. We cannot be
responsible for problems resulting from failure to observe the instructions in this manual.
• This manual uses various pictorial displays to show how to use this product safely and to avoid
harm to yourself and others and damage to your property.
Here is what these pictorial displays mean. Understanding them is important for reading this
manual.
• Meaning of displays
This symbol means important instructions. Failure to heed them can
result in serious injury or death.
Warning
This symbol means important instructions. Failure to heed them can
result in injury or property damage.
Caution
Warning
DO NOT DISASSEMBLE OR ALTER. Doing so may result in an accident, fire or electric shock.
USE THE CORRECT AMPERE RATING WHEN REPLACING FUSES. Failure to do so may
result in fire or electric shock.
MAKE THE CORRECT CONNECTIONS. Failure to make the proper connections may result in
fire or product damage.
USE ONLY IN CARS WITH A 12 VOLT NEGATIVE GROUND. (Check with your dealer if you are
not sure.) Failure to do so may result in fire, etc.
BEFORE WIRING, DISCONNECT THE CABLE FROM THE NEGATIVE BATTERY TERMINAL.
Failure to do so may result in electric shock or injury due to electrical shorts.
DO NOT ALLOW CABLES TO BECOME ENTANGLED IN SURROUNDING OBJECTS. Arrange
wiring and cables in compliance with the manual to prevent obstructions when driving. Cables or
wiring that obstruct or hang up on places such as the steering wheel, gear lever, brake pedals,
etc. can be extremely hazardous.
DO NOT SPLICE INTO ELECTRICAL CABLES. Never cut away cable insulation to supply
power to other equipment. Doing so will exceed the current carrying capacity of the wire and
result in fire or electric shock.
2-EN
DO NOT DAMAGE PIPE OR WIRING WHEN DRILLING HOLES. When drilling holes in the
chassis for installation, take precautions so as not to contact, damage or obstruct pipes, fuel
lines, tanks or electrical wiring. Failure to take such precautions may result in fire.
DO NOT USE BOLTS OR NUTS IN THE BRAKE OR STEERING SYSTEMS TO MAKE
GROUND CONNECTIONS. Bolts or nuts used for the brake or steering systems (or any other
safety-related system), or tanks should NEVER be used for installations or ground connections.
Using such parts could disable control of the vehicle and cause fire etc.
DO NOT BLOCK VENTS OR RADIATOR PANELS. Doing so may cause heat to build up inside
and may result in fire.
KEEP SMALL OBJECTS SUCH AS BATTERIES OUT OF THE REACH OF CHILDREN. Swal-
lowing them may result in serious injury. If swallowed, consult a physician immediately.
DO NOT INSTALL IN LOCATIONS WHICH MIGHT HINDER VEHICLE OPERATION, SUCH AS
THE STEERING WHEEL OR GEARSHIFT. Doing so may obstruct forward vision or hamper
movement etc. and results in serious accident.
Caution
HAVE THE WIRING AND INSTALLATION DONE BY EXPERTS. The wiring and installation of
this unit requires special technical skill and experience. To ensure safety, always contact the
dealer where you purchased this product to have the work done.
USE SPECIFIED ACCESSORY PARTS AND INSTALL THEM SECURELY. Be sure to use only
the specified accessory parts. Use of other than designated parts may damage this unit internally
or may not securely install the unit in place. This may cause parts to become loose resulting in
hazards or product failure.
ARRANGE THE WIRING SO IT IS NOT CRIMPED OR PINCHED BY A SHARP METAL EDGE.
Route the cables and wiring away from moving parts (like the seat rails) or sharp or pointed
edges. This will prevent crimping and damage to the wiring. If wiring passes through a hole in
metal, use a rubber grommet to prevent the wire’s insulation from being cut by the metal edge of
the hole.
DO NOT INSTALL IN LOCATIONS WITH HIGH MOISTURE OR DUST. Avoid installing the unit
in locations with high incidence of moisture or dust. Moisture or dust that penetrates into this unit
may result in product failure.
Precautions
• Be sure to disconnect the cable from the (–) battery post before installing your DVI-9990. This
will reduce any chance of damage to the unit in case of a short-circuit.
• Be sure to connect the color coded leads according to the diagram. Incorrect connections may
cause the unit to malfunction or damage to the vehicle’s electrical system.
• When making connections to the vehicle’s electrical system, be aware of the factory installed
components (e.g. on-board computer). Do not tap into these leads to provide power for this
unit. When connecting the DVI-9990 to the fuse box, make sure the fuse for the intended circuit
of the DVI-9990 has the appropriate amperage. Failure to do so may result in damage to the
unit and/or the vehicle. When in doubt, consult your ALPINE dealer.
• The DVI-9990 uses female RCA-type jacks for connection to other units (e.g. amplifier) having
RCA connectors.You may need an adaptor to connect other units. If so, please contact your
authorized ALPINE dealer for assistance.
3-EN
Contents
PRECAUTIONS
Accessories
Installation
2
5
6
Connections
9
Connections with other equipments
10
• To use this unit, a Multimedia Manager (PXI-H990, sold separately) or DAC unit (DAI-C990,
sold separately) is required. This unit is powered by connecting with the PXI-H990 or DAI-
C990.
IMPORTANT
Please record the serial number of your unit in the space provided below and keep it as a perma-
nent record. The serial number plate is located on the bottom of the unit.
SERIAL NUMBER:
INSTALLATION DATE:
INSTALLATION TECHNICIAN:
PLACE OF PURCHASE:
To prevent external noise from entering the audio system.
• Locate the unit and route the leads at least 10 cm away from the car harness.
• Keep the battery power leads as far away from other leads as possible.
• Connect the ground lead securely to a bare metal spot (remove any paint, dirt or grease if
necessary) of the car chassis.
• If you add an optional noise suppressor, connect it as far away from the unit as possible.
Your Alpine dealer carries various noise suppressors. Contact them for further information.
• Your Alpine dealer knows best about noise prevention measures so consult your dealer for
further information.
4-EN
Accessories
Power cable
RCA Extension
cable (video)
S video cable
Flat screw
(M5 x 6)
Front frame
x 4
Parts for remote control
Remote control
Battery (AAA)
Reinforcement screw Remote control holder
(M3 x 12)
x 2
Double-sided
adhesive tape
5-EN
Installation
Installation Location
Before deciding on the mounting location, check that opening and closing the display will not
hamper gear shifting in that position.
• Install at an angle of within 35 degrees from the horizontal.
1
Mounting Sleeve (Included)
Dashboard
DVI-9990
Remove the Detachable Front Panel (refer to page 9 of Owner’s Manual). Remove the front
frame from main unit (see “Removal” on page 7).
Slide the mounting sleeve into the dashboard.
2
Hex Nut (M5)
Screw
##
Bolt Stud
Metal Mounting
Strap
#
Ground Lead
DVI-9990
Chassis
Reinforce the head unit with the metal mounting strap (not supplied). Secure the ground lead of
the unit to a clean metal spot using a screw (#) already attached to the vehicle’s chassis.
NOTE
For the screw marked ##, use an appropriate screw for the chosen mounting location.
Connect each input lead coming from the product you are connecting with to the correspond-
ing output lead coming from the left rear of the DVI-9990. Connect all other leads of the DVI-
9990 according to details described in the “Connections” section.
6-EN
3
Slide the DVI-9990 into the dashboard. When the unit is in place, make sure the locking pins
are fully seated in the down position. This can be done by pressing firmly in on the unit while
pushing the locking pin down with a small screwdriver. This ensures that the unit is properly
locked and will not accidentally come out from the dashboard. Install the Detachable Front
Panel.
Lock Pin
Removal
1 Remove the DETACHABLE FRONT PANEL.
2 Use a small screwdriver (or similar tool) to push the locking pins to the “up” position (see above
drawing). As each pin is unlocked, gently pull out on the unit to make sure it does not re-lock
before unlocking the second pin.
3 Pull the unit out, keeping it unlocked as you do so.
< JAPANESE CAR >
Front Frame
DVI-9990
Screws (M5 x 6)
(Included)
Ground Lead
#
Mounting Bracket
NOTE
Secure the ground lead of the unit to a clean metal spot using a screw (#) already attached to the vehicle's chassis.
7-EN
Mounting the remote control holder
• If the remote control is in direct sunlight, remove it from the holder and keep it in the glove box.
• When the holder cannot be mounted securely with Velcro tape, mount it by using screws.
Reinforcement Screws
Remote Control
Remote Control
Holder
Protective paper
Console Box etc.
8-EN
Connections
• Basic Connection
Cable Color
Cable Specifications
•
Video output connector
Outputs a video signal.
Yellow
Connects to the video input of the TV monitor you are linking with.
• There is a copy protect signal included in the video output signal, so that recording
with a VCR (Video Cassette Recorder) etc., is not possible.
Also, depending on the monitor, the picture may not be displayed correctly.
•
•
•
IONBUS terminal
Connects with IONBUS compatible products.
S video output terminal
Outputs a video signal.
Connects with ALPINE products with a S video input terminal.
DVD Audio Link terminal
Connects with the DVD Audio Link terminal of the PXI-H990 Multimedia Manager or
DAI-C990 DAC unit.
(Connect when using a DVD audio disc. Remove the terminal cover and plug in the
DVD Audio Link cable).
•
•
•
Antenna Receptacle
Power Antenna Lead
Connect this lead to the +B terminal of your power antenna, if applicable.
Blue
Illumination Lead
Orange
Black
Red
This lead may be connected to the vehicle’s instrument cluster illumination lead.
This will allow the backlighting of the DVI-9990 to dim whenever the vehicle’s
lights are turned on.
•
•
Ground Lead
Connect this lead to a good chassis ground on the vehicle. Make sure the
connection is made to bare metal and is securely fastened using the sheet metal
screw provided.
Power supply unit
Switched Power Lead (Ignition)
Connect this lead to an open terminal on the vehicle’s fuse box or another unused
power source which provides (+)12V only when the ignition is turned on or in the
accessory position.
•
Battery Lead
Yellow
Connect this lead to the positive (+) post of the vehicle’s battery.
Fuse
(7.5A)
NOTES
•
Do not install the power supply unit where it will be exposed to moisture such as under the floor mat or near the air
conditioner. This may cause a malfunction.
•
•
Do not bundle the power supply unit cable with the audio cables. Noise may be induced into your system.
The power supply unit temperature can become hot. This is not a malfunction.
9-EN
Connections with other equipments
• System Connection <Example 1>
Connectable system products
IONBUS compatible monitor
Multimedia Manager or DAC unit
Ai-NET/IONBUS converter
Ai-NET compatible changer
XM Radio Receiver
TMI-M990
PXI-H990 or DAI-C990
KCI-500B
CHA-S634 or CHA-1214
TUA-T021XM or TUA-T020XM
System switch
“1 (SYSTEM)”
selected
IONBUS
compatible
monitor
(TMI-M990)
(sold separately)
DVD Audio Link cable
(Included with the PXI-H990 or DAI-C990)
To DVD Audio Link
terminal
*
System switch (PXI-H990 only)
Multimedia Manager
PXI-H990
•
Set to SINGLE when
connecting one PXI-H990.
To
or
IONBUS terminal
DAC unit
•
When connecting two PXI-
H990s, set the first to FRONT,
and the second to REAR.
IONBUS
compatible
monitor box
*
*
DAI-C990
(sold separately)
IONBUS cable
(Included with
the TMI-M990)
To
IONBUS
terminal
To IONBUS
terminal
When connecting the changer or
XM Radio Receiver, you must
use an Ai-NET/IONBUS converter
(KCI-500B).
*
*
IONBUS cable
(Included with the KCI-500B)
To
CD changer
(Ai-NET)
or
IONBUS
To Ai-NET
connector
terminal
XM Radio
Receiver
(sold
Ai-NET/IONBUS
converter
separately)
(KCI-500B)
(sold separately)
Ai-NET cable
(Included with CD changer or XM Radio Receiver)
*
Antenna Receptacle
To antenna plug of the vehicle
To power antenna
Blue
POWER
ILLUMINATION
GND
Orange
Black
To the instrument cluster illumination lead
<DVI-9990>
Connect to a metal part of chassis body with a screw.
IGNITION
BATTERY
Red
Ignition Key
Yellow
Power supply unit
Fuse (7.5A)
Battery
NOTES
•
Do not install the power supply unit where it will be exposed to moisture such as under the floor mat or near the air
conditioner. This may cause a malfunction.
•
•
Do not bundle the power supply unit cable with the audio cables. Noise may be induced into your system.
The power supply unit temperature can become hot. This is not a malfunction.
*
For the Ferrite Core, refer to the Owner’s Manual of the product that the IONBUS cable is attached to.
10-EN
• System Connection <Example 2>
Connectable system products
Multimedia Manager or DAC unit
External TV monitor
PXI-H990 or DAI-C990
IONBUS incompatible
TV monitor
RCA Extension cable (video)
(Included)
Video output connector
External TV
monitor
(sold separately)
Yellow
To DVD Audio Link
terminal
DVD Audio Link cable
(Included with the PXI-H990 or DAI-C990)
System switch
• Set to SINGLE when
connecting one PXI-H990.
Multimedia Manager
PXI-H990
or
IONBUS cable
(Included with the PXI-H990 or DAI-C990)
DAC unit
• When connecting two PXI-
H990s, set the first to FRONT,
and the second to REAR.
DAI-C990
(sold separately)
*
To IONBUS
terminal
*
Antenna Receptacle
To antenna plug of the vehicle
Blue
POWER
To power antenna
ILLUMINATION
GND
Orange
Black
Red
To the instrument cluster illumination lead
Connect to a metal part of chassis body with a screw.
IGNITION
BATTERY
Ignition Key
Yellow
Power supply unit
Fuse (7.5A)
Battery
NOTES
•
Do not install the power supply unit where it will be exposed to moisture such as under the floor mat or near the air
conditioner. This may cause a malfunction.
•
•
Do not bundle the power supply unit cable with the audio cables. Noise may be induced into your system.
The power supply unit temperature can become hot. This is not a malfunction.
*
For the Ferrite Core, refer to the Owner’s Manual of the product that the IONBUS cable is attached to.
11-EN
|