ABTI-GM1
ABTI-GM1
GM CLASS II
INTERFACE
FOR HANDSFREE
BLUETOOTH CAR KITS
The ABTI-GM1 is designed to integrate a Handsfree Bluetooth Car Kit into General Motors vehi-
cles that have the Class II data system. The OEM radio will mute when a call comes in and the
audio will be heard through the front speakers. The ABTI-GM1 is Plug-N-Play for the Motorola
IHF1000 and Parrot car kits, and it can be used with other car kits with modifications.
* READ IMPORTANT WARNING ON PAGE 1 BEFORE ATTEMPTING ANY INSTALLATION
AAPPPPLLIICCAATTIIOONNSS::
CHEVROLET
BUICK
Allure
OLDSMOBILE
Alero
2005-07
2004-05
2005-08
2004
2002-04
2002-05
2002
Suburban
Tahoe
2003-06
2003-06
2002-08
2005-08
2000-05
Century
Lacrosse
Regal
Bravada
Intrigue
Trailblazer
Uplander
Venture Van
Silhouette
2001-04
Rendezvous
2002-07
PONTIAC
Aztec
CADILLAC
2002-05
2002-05
2004-07
2002-05
2002-05
2006
GMC
Canyon
Envoy
Escalade/EXT
2003-06
Grand Am
Grand Prix
Montana
Sunfire
2004-08
2002-08
2003-07
CHEVROLET
Avalanche
Blazer
2003-06
2003-05
2003-05
2004-08
2005-06
2003-07
2002-05
2001-04
2002-05
2003-05
Savanna Van
Sierra (Classic) 2003-07
Torrent
Cavalier
Sonoma
Yukon
2003-05
2003-06
Colorado
SATURN
Relay
Equinox
2005-07
Express Van
Impala
HUMMER
H2
H3
2003-07
2006-08
Malibu (Classic)
Monte Carlo
S-10
ISUZU
Ascender
Silverado (Classic) 2003-07
SSR 2003-06
2003-06
I-Series Pickups 2006-08
1-800-221-0932
© COPYRIGHT 2007-2008 METRA ELECTRONICS CORPORATION
ABTI-GM1
INSTALLATION COMPONENTS
1) ABTI-GM1 interface
2) ABTI-GM1“T” harness
3) 8-Way connector to 8-Way connector harness
4) ISO to 8-way connector harness
TOOLS REQUIRED
1) Tools to remove the OEM radio
2) Wire ties
INSTALLING THE ABTI-GM1 WITH THE MOTOROLA IHF1000
Note: 8-Way to 8-Way connector harness is used in this application.
NOTE: The ISO to 8 way connector harness will NOT be used in this application.
INSTALLATION PROCEDURE
1) Disconnect the vehicle battery.
2) Remove the radio from the dashboard, and disconnect any cables connected to the radio.
FROM CAR
FROM CAR
2
ABTI-GM1
3) Insert the 24 pin plug on the Class 2 cable into the rear of the radio.
OM CAR
FROM CAR
FROM CAR
FROM CAR
White
4) Insert the 12 pin plug on the Class 2 cable into the rear of the radio.
OM CAR
FROM CAR
3
ABTI-GM1
5) Connect the 24 pin cap on the Class 2 cable to the 24 pin plug connected to the vehicle (the
connector that was removed from the back of the radio).
ABT
FROM CAR
FROM CAR
White
8 pin
6) Connect the 12 pin cap on the Class 2 cable to the 12 pin plug connected to the vehicle (the
connector that was removed from the back of the radio).
FROM CAR
FROM CAR
7) Connect the white 10-pin plug on the Class 2 cable to the ABTI-GM1 module.
ABTI-GM1
M CAR
FROM CAR
White
8 pin
plug
4
ABTI-GM1
8) Connect the white 8-pin plug on the IHF-1000 cable to the power cable, and connect the
other end of the power cable to the ABTI-GM1 module.
9) Install the IHF-1000 keypad on the dashboard of the vehicle, and route the wire to the IHF-
1000 harness. Attach the keypad connector to the harness.
FROM CAR
FROM CAR
ABTI-GM1
FROM CAR
FROM CAR
White
8 pin
plug
IHF-1000 keypad
10) Install the IHF-1000 microphone in an appropriate location (see IHF-1000 instructions), route
the wire to the IHF-1000 harness, and attach the microphone connector to the harness.
11) Secure all components, and reinstall the radio.
12) Reconnect the vehicle battery.
OPERATION
Refer to the Motorola IHF1000 manual for operation. Adjust the volume of the handsfree kit by
turning the volume knob of the radio. Audio from any source will be muted when a call comes
in or a call is made.
INSTALLING THE ABTI-GM1 WITH PARROT
HANDSFREE CAR KITS
*Note: The ISO to 8 way connector harness will be used in this application.
*Note: The 8 way to 8 way connector harness will NOT be used in this application.
Compatible Parrot kits: CK3000, CK3000 Evolution, CK3100, CK3300, CK3500, 3200LS,
3400LS-GPS, MK6000, MK6100
(Installation will be the same as the Motorola Handsfree kit steps 1-7)
8) Plug the 8 way side of the ISO to 8 way harness into the 8 way connector on the ABTI-GM1.
5
ABTI-GM1
9) Plug the ISO side of the ISO to 8 way harness into the mating Parrot connectors.
10) Take the Mute wire of the Parrot kit and plug it into the “Mute 1” wire in the Parrot ISO
harness.
11) Finish installing the rest of the Parrot handsfree kit and reinstall the OEM radio.
12) Reconnect the vehicles battery.
OPERATION
Refer to the Parrot manual for operation. Adjust the volume of the handsfree kit by turning the
volume knob of the radio. Audio from any source will be muted when a call comes in or a call
is made.
OTHER HANDSFREE KITS
Other handsfree kits can be used with the ABTI-GM1. Follow the steps below to wire the
handsfree kit:
1) Using the ISO to 8 way connector harness cut the ISO ends off.
2) The Yellow wire will go to the Battery wire of the handsfree kit.
3) The Red wire will go to the 12 volt accessory wire of the handsfree kit.
4) The Black wire will go to the ground of the handsfree kit.
5) The Purple wire will go to the Mute wire of the handsfree kit.
6) The White wire will go to the (+) speaker output of the handsfree kit.
7) The White/Black wire will go to the (-) speaker output of the handsfree kit.
Handsfree kits may have more then one speaker output on their harnesses however the
ABTI-GM1 needs only one speaker output to use.
6
ABTI-GM1 INSTRUCTIONS
1-800-221-0932
REV. 09/02/08 © COPYRIGHT 2007-2008 METRA ELECTRONICS CORPORATION INSTABTI-GM1
|