Apple
Multiple Scan 15AV
Display
User’s Guide
15-inch CRT (13.75-inch diagonal viewable image size)
Contents
Communications regulation information
v
2
1
Setting Up
Important safety instructions
What about electromagnetic emissions?
Getting ready to set up
1
1
3
Your Multiple Scan 15AV Display at a glance
Choosing a good location for your monitor
4
5
Connecting the monitor’s base
6
Positioning the monitor
7
Do you need a video card?
8
Do you need an adapter?
8
Using more than one monitor
8
Connecting the monitor to your computer
Connecting headphones to your monitor
9
11
Tur ning the monitor on
11
Installing the display software
12
iii
2
Using the Display Software
About the Control Strip 15
15
Working with the Control Strip
Changing screen resolution
16
17
Other things you can do with the Monitors control panel
Conserving energy 20
What happens after you turn on the energy-saving feature
Using Energy Saver with a screen saver 21
Using ColorSync 22
Configuring the Control Strip
Showing and hiding the Control Strip
Setting a keyboard command to show and hide the Control Strip
Changing the font in Control Strip menus 25
19
21
23
23
24
3
Adjusting the Picture
27
Accessing the monitor’s controls
Making adjustments to the picture
27
28
Adjusting the brightness of the picture
28
28
28
29
Adjusting the contrast of the picture
Adjusting the center of the picture
Adjusting the size of the picture
Adjusting the sound volume
30
Resetting controls to the factory settings
30
4
Tips and Troubleshooting
Care and cleaning 31
Protecting your monitor from theft
Troubleshooting 32
31
32
Appendix Technical Information
39
iv
Contents
Communications regulation information
FCC statement
This equipment has been tested and found to comply with the limits for a Class B digital device
in accordance with the specifications in Part 15 of FCC rules. See instructions if interference to
radio or television reception is suspected.
Radio and television interference
The equipment described in this manual generates, uses, and can radiate radio-frequency
energy. If it is not installed and used properly—that is, in strict accordance with Apple’s
instructions—it may cause interference with radio and television reception.
This equipment has been tested and found to comply with the limits for a Class B digital device
in accordance with the specifications in Part 15 of FCC rules. These specifications are designed
to provide reasonable protection against such interference in a residential installation. However,
there is no guarantee that interference will not occur in a particular installation.
You can determine whether your computer system is causing interference by turning it off. If
the interference stops, it was probably caused by the computer or one of the peripheral devices.
If your computer system does cause interference to radio or television reception, try to correct
the interference by using one or more of the following measures:
m
m
m
m
Turn the television or radio antenna until the interference stops.
Move the computer to one side or the other of the television or radio.
Move the computer farther away from the television or radio.
Plug the computer into an outlet that is on a different circuit from the television or radio.
(That is, make certain the computer and the television or radio are on circuits controlled by
different circuit breakers or fuses.)
If necessary, consult an Apple-authorized service provider or Apple. See the service and support
information that came with your Apple product. Or, consult an experienced radio/television
technician for additional suggestions.
IMPORTANT Changes or modifications to this product not authorized by Apple Computer, Inc.,
could void the FCC Certification and negate your authority to operate the product.
This product was tested for FCC compliance under conditions that included the use of Apple
peripheral devices and Apple shielded cables and connectors between system components. It is
important that you use Apple peripheral devices and shielded cables and connectors between
system components to reduce the possibility of causing interference to radios, television sets,
and other electronic devices. You can obtain Apple peripheral devices and the proper shielded
cables and connectors through an Apple-authorized dealer. For non-Apple peripheral devices,
contact the manufacturer or dealer for assistance.
Communications Regulation Information
v
DOC statement
DOC Class B Compliance This digital apparatus does not exceed the Class B limits for radio
noise emissions from digital apparatus as set out in the interference-causing equipment standard
entitled “Digital Apparatus,” ICES-003 of the Department of Communications.
Observation des normes—Classe B Cet appareil numérique respecte les limites de bruits
radioélectriques applicables aux appareils numériques de Classe B prescrites dans la norme
sur le matériel brouilleur : “Appareils Numériques”, NMB-003 édictée par le ministre des
Communications.
VCCI statement
vi
Communications Regulation Information
1
Setting Up
The Apple Multiple Scan 15AV Display is a 15-inch color monitor (diagonal
viewable image size is 13.75 inches) that supports a variety of resolutions and
has a built-in amplifier and stereo speakers for producing sounds and music.
This chapter describes important safety information, setting up and
connecting the monitor to your computer, and installing the monitor software
on your computer.
Important safety instructions
For your own safety and that of your equipment, always take the following
precautions.
Disconnect the power plug (by pulling the plug, not the cord) if any of the
following conditions exists:
m the power cord or plug becomes frayed or otherwise damaged
m you spill something into the case
m your monitor is exposed to rain or any other excess moisture
m your monitor has been dropped or the case has been otherwise damaged
m you suspect that your monitor needs service or repair
m you want to clean the case (use only the recommended procedure
described in “Care and Cleaning” in Chapter 4)
IMPORTANT The only way to disconnect power completely is to unplug the
power cord. Make sure at least one end of the power cord is within easy reach
so that you can unplug the monitor when you need to.
1
Be sure that you always do the following:
m Keep your monitor away from sources of liquids, such as wash basins,
bathtubs, shower stalls, and so on.
m Don’t remove the cover of the monitor.
m Don’t set anything on top of the monitor (such as a book or cup).
m Keep the monitor’s vents free from obstruction.
m Protect your monitor from dampness or wet weather, such as rain, snow,
and so on.
m Read all the installation instructions carefully before you plug your
monitor into a power source.
m Keep these instructions handy for reference by you and others.
m Follow all instructions and warnings dealing with your system.
WARNING Electrical equipment may be hazardous if misused. Operation
of this product, or similar products, must always be supervised by an
adult. Do not allow children access to the interior of any electrical
product and do not permit them to handle any cables.
What about electromagnetic emissions?
There has been recent public discussion of the possible health effects of
prolonged exposure to extremely low frequency (ELF) and very low
frequency (VLF) electromagnetic fields. Such fields are associated with
electromagnetic sources such as television sets, electrical wiring, and some
household appliances—as well as computer monitors.
Apple has reviewed scientific reports and sought the counsel of government
regulatory agencies and respected health organizations. Based on the
prevailing evidence and opinions, Apple believes that the electric and
magnetic fields produced by computer monitors do not pose a health risk.
In response to those customers who wish to reduce their exposure to
electromagnetic fields, Apple has lowered the emission levels of our products.
We are also actively encouraging further scientific research so we can
continue to promote the health and safety of our customers and employees.
2
Chapter 1
Getting ready to set up
As you begin to set up your display system, be sure you have easy access to
the following items for your Multiple Scan 15AV Display:
Apple Multiple
Scan 15AV Display
f
I
Sound cable
Monitor cable
Power cord
Software
User’s guide
Note: Your power cord may appear different from the one pictured here.
3
Setting Up
Your Multiple Scan 15AV Display at a glance
Stereo
speakers
I
I
Power button
f
f
Headphone
jack
_
Volume control
Control panel
O
Contrast control
¤
Brightness control
F
_
F
Security slot
_
Sound input port
≤
™
Monitor cable
≤
Power cord
receptacle
4
Chapter 1
Choosing a good location for your monitor
Here are some key factors to consider when determining where to place your
monitor:
m Be sure that the desk or table can support the monitor’s weight—
approximately 30 pounds.
m Make sure that the power cord will reach an available AC outlet.
m Make sure the monitor cable will reach from the back of the monitor to
your computer. The monitor cable should be unobstructed when you swivel
and tilt the monitor, so allow at least 6 inches of clearance in the back. If
you don’t allow enough clearance, the monitor connector might be
damaged when the cable hits an obstruction.
5
Setting Up
Connecting the monitor’s base
The monitor and base are packaged separately. To connect the monitor’s base,
follow these steps:
1
2
3
4
Place the monitor on its left side on a table or other firm surface.
Place the base on its side facing the bottom of the monitor.
Hook the rear latches into the holes at the rear of the monitor.
Insert the front latches into the slots at the front of the monitor.
First, hook the rear latches into
the holes at the rear of the base.
Then, snap the front latches
into the slots.
5
Turn the monitor upright.
Yo u’r e finished connecting the base.
6
Chapter 1
Positioning the monitor
Once your monitor is in place, either on top of your computer or next to it
on a desk or table, follow these steps:
1
2
3
Place the monitor so that the screen faces the user.
To slide the monitor, lift the front up slightly and push or pull in the direction you want.
Adjust the viewing angle of the monitor by tilting it up or down and turning it left or right
on its stand.
Position the monitor so that when you use it, no bright light is behind the
monitor or reflected on the screen. Your eyes should be about level with the
top edge of the screen and between 18 and 28 inches (45 to 70 cm) away. Take
occasional breaks when using your computer, to focus your eyes on a distant
object.
For your greatest comfort, use the following illustration to help you in
positioning your monitor.
45–70 cm (18–28 in.)
Shoulders relaxed
Top of the screen at or slightly
below eye level (You may need
to adjust the height of your
monitor by placing something
under it or by raising your
work surface.)
Forearms and hands
in a straight line
Forearms level
or tilted up slightly
Screen positioned to avoid
reflected glare
Lower back supported
Thighs horizontal
Clearance under work surface
Feet flat on the floor
7
Setting Up
Do you need a video card?
To use th e Multiple Scan 15AV Display, you need compatible video circuitry
built into your computer or a compatible video card installed in your
computer. If you are unsure whether your computer has the appropriate built-
in video capability, check the technical specifications that came with your
computer or check with an Apple-authorized dealer or service provider.
If your computer does not have built-in video capability, you need to install a
video card (available from an Apple-authorized dealer or service provider).
Depending on your computer model, you will need either a NuBus™ card or a
PCI card. You should install the video card before you connect the monitor to
your computer. For instructions on installing a card inside your computer, see
the manual that came with your computer or video card.
Do you need an adapter?
Some Macintosh computer models and some video cards from manufacturers
other than Apple require an adapter to connect the monitor to the computer.
Adapters are available from an Apple-authorized dealer or service provider.
Using more than one monitor
If your computer has NuBus or PCI expansion slots, you can connect
additional monitors to your computer. You may need to install a video card
for each additional monitor you are using. See the documentation that came
with your computer for information on working with additional monitors.
8
Chapter 1
Connecting the monitor to your computer
Follow these steps to connect the Multiple Scan 15AV Display to your
computer:
IMPORTANT Before you connect any cords or cables, make sure that your
computer is turned off and unplugged.
WARNING Your monitor is equipped with a three-wire grounding plug—
a plug that has a third (grounding) pin. This plug will fit only a
grounded AC outlet. This is a safety feature. If you are unable to insert
the plug into the outlet, contact a licensed electrician to replace the
outlet with a properly grounded outlet. Do not defeat the purpose of the
grounding plug!
1
Connect the socket end of the power cord to the power cord receptacle on the back of
the monitor.
F
_
≤
9
Setting Up
2
3
Plug the other end of the power cord into an outlet or power strip.
If your computer has an available power socket, you can use a detachable
power cord with a recessed end to plug the monitor directly into the
computer. You can get this cord from an Apple-authorized dealer or service
provider.
Connect the monitor cable to the monitor port (marked with
computer.
™) on the back of the
Monitor port icon
Monitor cable
If you installed a video card in your computer, connect the monitor cable to
the video card’s port. For more information about installing video cards, see
the manual that came with your computer or video card.
4
5
Tighten the thumbscrews on the connection.
Attach one end of the included sound cable to the sound output port (marked
by
-) on the back of the computer.
6
Attach the other end of the sound cable to the sound input port (marked by
back of the monitor.
-) on the
10
Chapter 1
Connecting headphones to your monitor
If you wish, you can plug a pair of headphones (or other sound output device)
into the Multiple Scan 15AV Display. To plug your headphones into the
monitor, follow these steps:
1
2
If your headphones are attached to the sound output port (marked by
your computer, unplug them.
-) on the back of
If the sound cable that came with the Multiple Scan 15AV Display is not connected,
connect it to the sound output port on the computer and on the monitor. (Both sound
output ports are marked by
-).
3
Plug the headphones into the headphone port (marked by
f) on the front of the monitor.
When headphones are plugged in, you do not hear sound through the stereo
speakers. Sound and music play through the headphones only.
Turning the monitor on
To tur n on the monitor for the first time:
1
2
Start up your computer.
Press the Power button on the front right side of the monitor.
Power indicator light
Power button
f
I
The green power indicator light goes on.
If the green light does not go on, press the power switch again. If this doesn’t
work, make sure you’ve connected the monitor to your computer properly (see
“Connecting the Monitor to Your Computer,” earlier in this chapter) and make
sure the monitor is plugged into a working electrical outlet. Also, make sure
your computer is turned on.
11
Setting Up
Note: If the power light is yellow or amber, one of the following may be the
cause:
m The computer isn’t turned on.
m The monitor’s cable isn’t connected properly to the computer.
m The video circuitry or video card in your computer is not compatible with
the monitor. Your Macintosh may need a video card or adapter to use the
monitor. See “Do You Need a Video Card?” earlier in this chapter.
m The computer and monitor are in sleep to conserve energy. See
“Conserving Energy” in Chapter 2.
To ma ke full use of the features available to you with this monitor, you should
install the display software. Follow the instructions in “Installing the Display
Software,” next.
Installing the display software
To i nsta ll the display software for the Multiple Scan 15AV Display, follow
these steps:
1
2
Insert the Apple Multiple Scan Software for Macintosh disk into a floppy disk drive.
The disk’s icon appears on the desktop.
Double-click the disk icon to open it.
3
Double-click the Installer icon to start the Installer program.
After a moment, the Installer opens and you see the Welcome screen.
12
Chapter 1
4
Read the Welcome screen and click OK.
The Installer screen appears.
5
6
Make sure the disk named in the box is the one on which you want to install the
software. If not, click Switch Disk until the correct disk name appears.
Click the Install button.
The Installer takes a few moments to calculate what needs to be done and
then begins to copy files.
7
When the installation is complete, follow the instructions on the screen.
After the installation, the Installer tells you to restart your computer (if you
installed the software onto your startup disk) or to quit (if you installed the
software onto another disk).
The software is now installed and the monitor is ready for use.
Note: To change the screen resolution, see “Changing Screen Resolution” in
Chapter 2.
13
Setting Up
2
Using the Display Software
This chapter explains how to use the new display software you have installed.
Your software includes a new feature called the Control Strip, which you can
use to change monitor settings quickly and easily. You can use the Control
Strip to change screen resolutions, change the number of colors your monitor
displays, and change the volume of your computer’s beep sound. Your monitor
also comes with control panels that you can use to save energy and fine-tune
your monitor’s use of color.
About the Control Strip
When you start up your Macintosh after installing your new display software,
you will notice the Control Strip at the lower-left edge of your screen. The
Control Strip is a new way of changing certain settings from your desktop
without opening control panels.
Note: Some versions of the Macintosh Operating System will show different
modules in the Control Strip. If your Control Strip doesn’t match what’s
shown in this chapter, consult the on-screen help that came with your
computer or system software upgrade kit.
Monitor
Sound
Monitor
Resolution
Volume BitDepth
15
You can change the following settings with the Control Strip modules:
m Monitor Resolution lets you change the resolution of the screen.
m Monitor BitDepth lets you change the number of colors on your screen.
m Sound Volume lets you change the volume of the system sound.
To use a module, press it and choose a setting from the pop-up menu that
appears.
Note: If you use more than one monitor, the monitors are identified by
number in the Control Strip menus. To see which number goes with which
monitor, experiment with the modules, or open the Monitors control panel (in
the Control Panels folder, available from the Apple [K] menu) and press the
Identify button. The number of each monitor appears on its screen. (On some
models, the control panel has a different name.)
Working with the Control Strip
You can move, collapse, and expand the Control Strip, and you can change the
order of the controls.
Tab
m To move the Control Strip, hold down the Option key on your keyboard and
drag the tab at the right end of the Control Strip. The Control Strip always
stays on the left or right edge of a screen.
m To ma ke th e Control Strip shorter or longer, drag the tab to the left or right.
m To s ee hidden controls when the Control Strip is not expanded to its full
size, click the right and left arrows.
m To colla pse the Control Strip to its smallest size, click the tab or the box. To
expand the collapsed Control Strip to its original size, click the tab.
m To move a control to a new position in the Control Strip, hold down the
Option key on the keyboard and drag the control to where you want it.
For more information on setting up the Control Strip, see “Configuring the
Control Strip,” later in this chapter.
16
Chapter 2
Changing screen resolution
You can change the resolution of your monitor to zoom in for detail work or
to zoom out and see a whole page or more at a time.
m
To change screen resolution with the Control Strip, press the Resolution control and
choose the resolution you want in the menu.
To change your screen resolution with the Monitors control panel, follow
these steps.
Note: Some models use a different control panel. If you don’t see the
Monitors control panel, consult the on-screen help that came with your
computer or system software upgrade kit.
1
2
Choose Control Panels from the Apple (K) menu.
A window opens showing all the control panels.
Double-click the Monitors icon to open the Monitors control panel.
Double-click the icon. (If you don’t see it,
click the scroll bar arrows. If you still can’t
find it, you may have forgotten to install
the software, as described in Chapter 1.)
17
Using the Display Software
3
Make the following choices in the control panel:
Note: The choices you see in this window may differ from those shown here,
depending on your computer, your video capability, and the monitors
attached.
First, if you have more than one monitor, click
here to see how your monitors are numbered.
Second, click the icon of the monitor you want
to change. (If you only have one monitor, you
will only see one choice.)
Third, choose when you want the change to take place—after
you close this window or when you restart your computer.
4
5
Click the Options button to see what resolutions you can choose.
Click a resolution to select it.
The choices you see in this window depend on your computer, video
capability, and the monitors that are attached.
If you don’t see any options for changing resolutions, you may have selected
the wrong monitor in the control panel, or your computer and video card may
not support multiple resolutions. Click Cancel, then try step 3 again.
Note: In some cases, you can see additional choices if you hold down the
Option key on the keyboard while you click the Options button. However,
these choices may not be optimized for your monitor. If you try to make a
choice that is not optimized for your monitor, you’ll see a message, or the
monitor will go blank or show “static” for several seconds, then will switch
back to an optimized resolution.
18
Chapter 2
6
7
Click OK to return to the main window of the Monitors control panel.
Depending on which option you selected in the control panel, the new
resolution will be displayed when you close the dialog box or when you
restart the computer.
Close the Monitors control panel by clicking the close box in the upper-left corner.
IMPORTANT Make sure you close the Monitors control panel before starting
any other work.
Note: When you change monitor resolutions, the folders and icons on your
desktop may reposition themselves to accommodate the new screen size.
8
If the image is distorted, try another resolution, or adjust the controls on the monitor as
explained in Chapter 3.
Other things you can do with the Monitors control panel
You can also use the Monitors control panel to
m arrange how multiple monitors work together
m choose how many colors or shades of gray each monitor can display (you
can also make this change using the Control Strip)
See the instructions that came with your computer for details. (Some models
have a different control panel.)
19
Using the Display Software
Conserving energy
When you save energy, you save natural resources and reduce pollution. Your
Multiple Scan 15AV Display includes features that automatically save energy.
You can increase the energy savings by turning your computer and monitor
off if you won’t be using them for a while—for example, overnight or over the
weekend.
You use the Energy Saver control panel to tell the monitor how to conserve
energy after a specified period of inactivity.
You can use the control panel if your monitor is connected to a computer that
complies with the United States Environmental Protection Agency’s Energy
Star program. (Look for the EPA Energy Star logo on the box.)
To use th e control panel, follow these steps:
1
2
Choose Control Panels from the Apple (K) menu.
A window opens showing all the control panels.
Double-click the Energy Saver icon to open the Energy Saver control panel.
Double-click the icon. (If you don’t see it, click the scroll
bar arrows. If you still can’t find it, you may have forgotten
to install the software, as described in Chapter 1.)
3
Make the following choices in the control panel:
Click here to turn
Energy Saver on
or off. When there’s
an X in this box,
If Energy Saver is on, slide this control to
determine how long Energy Saver will wait
without activity before darkening the screen.
Energy Saver is on.
4
Close the control panel.
20
Chapter 2
What happens after you turn on the energy-saving feature
When Energy Saver is on, the monitor “goes to sleep” after a specified period
of inactivity. The monitor screen looks dark and the monitor is using less
energy. When the monitor is asleep, your computer is still working. But to
prevent accidental changes, you can’t make any changes while the monitor is
asleep.
To “ wake up” the monitor, move the mouse or press any key on the keyboard.
Your computer beeps while the monitor is waking up. The process takes
about 20 seconds, and you can begin work as soon as the computer stops
beeping. (The beep volume cannot be adjusted; it is not controlled by the
computer’s sound software.)
IMPORTANT The Energy Saver control panel works with Apple monitors (such
as this one) that comply with the EPA’s Energy Star program and any other
monitor that complies with the Video Electronics Standards Association’s
Display Power Management Standard (VESA DPMS). Your computer model
must also be compatible with Energy Star. Other monitors will darken after
the specified inactivity period, but they won’t go to sleep or save energy.
Using Energy Saver with a screen saver
“Screen saver” programs darken the screen or display a changing image on
the monitor if the computer is not used for prolonged periods. Both screen
saver programs and the Energy Saver feature prevent images from “burning
in” and damaging the screen. Energy Saver also conserves energy.
If you wish, you can use both Energy Saver and a screen saver program. Set
the screen saver to come on before Energy Saver, so if you’re away from the
computer for a short while, you can return to work immediately, without
waiting for the monitor to wake up. If you’re gone for a while longer, however,
the monitor won’t use as much energy.
21
Using the Display Software
Using ColorSync
ColorSync is Apple’s unique color-matching software that ensures that Apple
color printers print the best possible reproduction of the colors that appear on
your monitor screen. ColorSync is also used by Apple color scanners and the
QuickTake camera to capture color images and accurately reproduce their
colors on the screen. ColorSync maintains consistent colors between color
input, your monitor, and color printing devices so that the colors of your
original image are accurately reproduced on screen and when printed.
The ColorSync software works automatically in the background. When you
install the display software, your computer is automatically set to use
ColorSync with your monitor.
If you use more than one color monitor with your Macintosh and want to
print a color image from a specific monitor, you can obtain the best color
matching by setting ColorSync to use a specific monitor.
To se t up ColorSync for a specific monitor:
1
2
Choose Control Panels from the Apple (K) menu.
A window opens showing all the control panels.
Double-click the ColorSync icon to open the ColorSync control panel.
The ColorSync control panel appears.
22
Chapter 2
3
Click Set Profile.
A dialog box appears that enables you to select the name of the monitor you
want to use.
4
5
6
Click a monitor name to select it.
Click Select to return to the main window of the ColorSync control panel.
Close the ColorSync control panel by clicking the close box in the upper-left corner.
Configuring the Control Strip
With the Control Strip control panel, you can show and hide the Control Strip
and choose a keyboard command to show/hide the Control Strip. You can also
choose the font that appears in the Control Strip menus.
Showing and hiding the Control Strip
To show or hide the Control Strip, follow these steps:
1
2
Choose Control Panels from the Apple (K) menu.
Double-click the Control Strip icon to open it.
The Control Strip control panel appears.
23
Using the Display Software
3
To show or hide the Control Strip, click the button labeled Show Control Strip or Hide
Control Strip.
The change takes effect immediately.
4
Click the close box to close the control panel.
Setting a keyboard command to show and hide the Control Strip
To se t a keyboard command to show and hide the Control Strip, follow these
steps:
1
2
Choose Control Panels from the Apple (K) menu.
Double-click the Control Strip icon to open it.
The Control Strip control panel appears.
3
To turn on the keyboard command for showing and hiding the Control Strip, click “Hot
key to show/hide.”
The keyboard command for showing and hiding the Control Strip appears in
the “Current hot key” window.
24
Chapter 2
4
To change the keyboard command, click “Define hot key.”
A box appears.
5
6
Press the keys you want to use, then click OK.
You must include either the x (Command) key or a function key (F1–F15). If
you choose an inappropriate command, you see a message.
Click the close box to close the control panel.
Changing the font in Control Strip menus
When you press a Control Strip control, you see a menu you can use to make
changes. You can change the font and size of items in the menu. Follow these
steps:
1
2
Choose Control Panels from the Apple (K) menu.
Double-click the Control Strip icon to open it.
The Control Strip control panel appears.
25
Using the Display Software
3
4
To change the font, choose a font from the Font pop-up menu. To change the font size,
choose a size from the Size pop-up menu.
Click the close box to close the control panel.
26
Chapter 2
3
Adjusting the Picture
In most cases, you won’t need to make any adjustments to the picture.
However, you can fine-tune the screen display to suit your preferences using
the controls on the front of the monitor. After you set the controls, your
monitor will use your settings each time you turn on the computer.
Accessing the monitor’s controls
A flip-down panel covers some of the controls on the front of the monitor.
m To open the panel so the monitor’s controls are accessible, gently push
down on the panel. It opens and flips down. You can now use the controls
to adjust the picture.
m To close the panel, flip the panel up and gently push it till the door latches.
Indicator lights
for picture controls
Press this button to select
a picture control to the left.
Contrast
control
Brightness
control
_
SELECT
RECALL
O
¤
Volume
control
Flip-down
panel
Down arrow
Up arrow
Recall button
27
Making adjustments to the picture
Adjusting the brightness of the picture
Turn the brightness control to increase or decrease brightness.
¤
Adjusting the contrast of the picture
Turn the contrast control to increase or decrease contrast.
O
Adjusting the center of the picture
1
Press the Select button on the monitor until the indicator light for the vertical center icon
goes on.
SELECT
2
Adjust the vertical center of the picture by pressing the Down button to move the picture
down or the Up button to move it up.
28
Chapter 3
3
Press the Select button until the indicator light for the horizontal center icon goes on.
SELECT
4
Adjust the horizontal center of the picture by pressing the Down button to move the
center of the picture left or the Up button to move the center of the picture right.
When the picture is centered properly, an equal border appears around the
picture.
Adjusting the size of the picture
1
Press the Select button on the monitor until the indicator light for the width icon goes on.
SELECT
2
Adjust the width of the picture by pressing the Down button to narrow the picture or the
Up button to widen the picture.
29
Adjusting the Picture
3
Press the Select button until the indicator light for the height icon goes on.
SELECT
4
Adjust the height of the picture by pressing the Down button to shorten the picture or the
Up button to lengthen the picture.
Adjusting the sound volume
Turn the volume control to increase or decrease sound volume.
_
Resetting controls to the factory settings
The picture controls for your monitor are set at the factory. You can fine-tune
the picture and make adjustments if necessary. The monitor will use your
adjusted settings each time you turn on the computer. If you later decide you
want to revert to the factory settings, press the Recall button.
RECALL
30
Chapter 3
4
Tips and Troubleshooting
This chapter includes information on the care and cleaning of your monitor,
protecting your monitor from theft, and troubleshooting.
Care and cleaning
m
m
m
Do not block the monitor’s vents.
Do not let liquid get on or into the monitor.
If you will not be using your monitor and computer for a long period of
time (a day or more), make sure you turn off the computer (and your
monitor, if necessary).
To cle a n the case of the monitor:
1
2
Turn your computer and monitor off.
Disconnect the monitor’s power plug from the back of the monitor. (Pull the plug, not
the cord.)
3
Wipe the surfaces lightly with a clean, soft cloth dampened with water.
Don’t use aerosol sprays, solvents, or abrasives that might damage the finish
on the case.
31
To cle a n the screen of the monitor:
1
2
Turn your computer and monitor off.
Disconnect the monitor’s power plug from the back of the monitor. (Pull the plug, not
the cord.)
3
Use a mild, non-abrasive cleaner on a soft cloth and wipe the screen. Don’t spray the
cleaner onto the screen, because the liquid may drip inside the monitor.
Protecting your monitor from theft
The slot on the back of the monitor is for connecting a security lock. It lets
you attach a narrow, flexible cable that you can use to secure your monitor
(and the rest of your computer system) to prevent theft. Security locks are
available from an Apple-authorized dealer or service provider.
Troubleshooting
WARNING If you have a problem with your monitor and nothing
presented in this manual solves it, consult the service and support
information that came with your monitor for instructions on how to
contact an Apple-authorized service provider or Apple for assistance. If
you attempt to repair the monitor yourself, any damage you may cause
to the monitor will not be covered by the limited warranty on your
monitor. Contact an Apple-authorized dealer or service provider for
additional information about this or any other warranty question.
Solutions to common problems related to your monitor are described here.
Problems related to the computer are covered in the manuals that came with
your computer.
WARNING Never remove the cover from the monitor; you could come in
contact with hazardous voltage.
32
Chapter 4
The monitor’s power indicator light doesn’t come on.
m
m
Make sure the monitor is turned on.
Make sure that the power cord is plugged in properly.
If the monitor power cord is plugged into a wall outlet, make sure the cord is
firmly plugged in. Check whether power to the outlet has been interrupted.
You can test the outlet by plugging in something that you know works—
such as a desk lamp or radio. If the test appliance works, but the monitor
doesn’t, contact an Apple-authorized dealer or service provider.
If the monitor power cord is plugged into your computer, make sure your
computer is on and the cord is firmly plugged in.
m
m
Make sure the monitor cable is plugged into your computer properly.
If you have a video card installed in your computer, the monitor cable should
be plugged into the port for the video card.
If you do not have a video card installed in your computer, the monitor cable
should be plugged into the monitor port on the back of your computer.
Make sure the thumbscrews on the monitor cable are tightened securely
into the port connector.
No image appears on the screen and the monitor’s power indicator light is on.
m
The monitor may have gone to sleep. Move the mouse or press a key to
wake the monitor. (See “Conserving Energy” in Chapter 3.)
m
Make sure the monitor cable is connected to the correct port on the back of
the computer.
If you have a video card installed in your computer, the monitor cable should
be plugged into the port for the video card.
If you do not have a video card installed in your computer, the monitor cable
should be plugged into the monitor port on the back of your computer.
m
m
Make sure the thumbscrews on the monitor cable are tightened securely
into the port connector.
Make sure the brightness (¤) and contrast (O) controls are set correctly.
See “Adjusting the Brightness of the Picture” and “Adjusting the Contrast
of the Picture” in Chapter 3.
33
Tips and Troubleshooting
m
If the power indicator light is yellow or amber, one of the following may be
the cause:
m The computer isn’t turned on.
m The monitor’s cable isn’t connected properly to the computer.
m The video circuitry or video card in your computer is not compatible
with the monitor. Your Macintosh may need a video card or adapter to
use the monitor. See “Do You Need a Video Card?” in Chapter 1.
m The computer and monitor are in sleep to conserve energy. See
“Conserving Energy” in Chapter 2.
The screen is dark or appears dim.
m
m
Make sure that your computer and monitor are turned on.
Make sure that the power cord and the monitor cable are securely
connected.
m
m
Increase the brightness (¤) and contrast (O) of the picture. See “Making
Adjustments to the Picture” in Chapter 3.
The Energy Saver option may be activated. Move the mouse or press any
key on the keyboard to reactivate the monitor. In approximately 20 seconds
(or until you no longer hear the beep), the monitor is reactivated.
m
A screen saver that darkens your screen may be activated. Move the mouse
or press any key on the keyboard to reactivate the monitor.
The screen flickers.
m
Make sure the monitor cable is connected firmly to the correct port on the
back of the computer.
If you have a video card installed in your computer, the monitor cable should
be plugged into the port for the video card.
If you do not have a video card installed in your computer, the monitor cable
should be plugged into the monitor port on the back of your computer.
m
The flickering could be caused by interference from a nearby power line, a
fluorescent light, or electrical device—for example, a radio, a microwave
oven, or another computer. Try relocating nearby electrical devices or
moving your computer and monitor.
34
Chapter 4
m
m
If you have more than one monitor attached to your computer, the monitors
may interfere with one another. Move the monitors farther apart or set the
monitors at an angle, so their screens are close and their back panels are
farther apart. If you still see flickering after moving the monitors more
than 16 inches apart, contact an Apple-authorized dealer or service
provider.
If you are using a video card that has a very low refresh rate (below 60
hertz), the monitor may flicker. You may be able to change the refresh rate
for the card. See the documentation that came with your video card for
more information.
No colors appear on the screen.
m
Make sure that the number of colors is set correctly in the Control Strip or
control panel. See “Using the Control Strip” in Chapter 2, and see the on-
screen help that came with your computer.
The screen image is off center.
m
Try changing to another resolution. See “Changing Screen Resolution” in
Chapter 2.
m
Adjust the center of the picture. See “Adjusting the Center of the Picture”
in Chapter 3. (Keep in mind that if you adjust the center of the picture, you
may have to adjust it again if you change resolutions.)
The screen image is too large or too small.
m
Try changing to another resolution. See “Changing Screen Resolution” in
Chapter 2.
m
Adjust the horizontal or vertical size of the picture. See “Adjusting the Size
of the Picture” in Chapter 3. (Keep in mind that if you adjust the horizontal
or vertical size of the picture, you may have to adjust it again if you change
resolutions.)
Before you finish adjusting the monitor controls, the picture control indicator light
goes out.
m
If you pause for several seconds while adjusting the controls, the monitor
assumes you are finished.
35
Tips and Troubleshooting
The screen appears greenish, the screen image is unreadable, or there is “snow” on
the screen.
m
Make sure the monitor cable is connected firmly to the correct port on the
back of the computer.
If you have a video card installed in your computer, the monitor cable should
be plugged into the port for the video card.
If you do not have a video card installed in your computer, the monitor cable
should be plugged into the monitor port on the back of your computer.
After many hours of use, the screen image appears dim.
m
Increase the brightness (¤) and contrast (O) of the picture. See “Making
Adjustments to the Picture” in Chapter 3.
Over time, you experience eyestrain.
m
Adjust the screen contrast (O). In a bright room, contrast is usually best set
at maximum; in a dim room, lower contrast is usually more comfortable.
See “Adjusting the Contrast of the Picture” in Chapter 3. Also, be sure to
take occasional breaks to focus your eyes on a distant object.
You don’t hear any sound from your computer.
m
Make sure sound is turned on and make sure your sound options are set
correctly in the Control Strip or control panel for sound. See “About the
Control Strip” in Chapter 2 and see the on-screen help that came with your
computer or system software upgrade kit.
m
m
Adjust the sound volume on your monitor. See “Adjusting the Sound
Volume” i n Chapter 3.
Check whether headphones are plugged into the headphone port (marked
by f) on the monitor. If so, you will be able to hear sound only in the
headphones.
m
Check whether something is plugged into the sound output port (marked
by -) on the back panel of your computer. The computer’s internal
speaker is turned off whenever a cable is connected to the sound output
port. If a sound cable is connected between the computer and monitor, you
can hear sound from the monitor’s speakers or from headphones connected
to the monitor’s headphone port (marked by f). For more information, see
Chapter 1, “Setting Up.”
You can’t find the Control Strip.
m
You may have hidden the Control Strip. Open the Control Strip control
panel and click the button labeled Show Control Strip.
36
Chapter 4
You can’t control the sound volume of a CD.
m The volume control on the Control Strip affects the computer’s beep sound
only. To control the volume of a CD, use the AppleCD Audio Player,
located in the Apple (K) menu.
You don’t see the monitor resolution you want.
You can see additional resolution choices in the Monitors control panel if you
hold down the Option key on your keyboard while you click the Options
button in the control panel. In the list that appears, click the resolution you
want. (Some models use a different control panel. Consult the documentation
that came with your computer or system software upgrade kit.)
Note: Some of the items in this list are not optimized for your monitor. If you
choose a resolution that doesn’t work with your monitor, you may see a
message, or your monitor may go blank or show static. After approximately 15
seconds, your monitor should revert to a usable resolution. If it does not,
restart your computer.
After you change the screen resolution, a window is stuck, halfway off the screen, or
missing; or you can’t see the whole screen.
Try one of the following:
m If you changed the resolution in a control panel, make sure the control
panel is closed before trying to use another window.
m Quit the program whose window is missing and then open it again.
m If the program has a Windows menu, use it to hide the problem window
and then show it again.
m Go back to the resolution you were using, close the window, change the
resolution, and then reopen the window.
m Try another resolution.
If you have problems with a particular program, contact the publisher of that
program. Not all programs take advantage of your monitor’s multiple
resolution feature.
After you change the number of colors displayed on the screen, the colors don’t
look right.
Try one of the following:
m Quit the program you’re running and start it again.
m Go back to the number of colors you were using.
37
Tips and Troubleshooting
After you change the screen resolution, icons move.
Changing the screen resolution affects how information can be displayed on
your screen. The display software may automatically reposition icons after
you change the screen resolution.
After you attached a new monitor to your computer, the new monitor’s screen is blank or
shows “garbage” or “snow.”
The computer may not have recognized the monitor. Try the following: Turn
off the computer and disconnect the new monitor. Start the computer with no
monitor attached. Wait a minute or so for the computer to finish turning itself
on. Turn off the computer again and reattach the new monitor.
The monitor does not go to sleep.
Some computers and video cards do not support the Energy Saver feature. See
the documentation that came with your computer and video card for more
information.
If you have a Power Macintosh 9500, you can get an upgrade to your software
that allows your monitor to work with Energy Saver. Call the Apple Service
and Support number found in the service and support information that came
with your computer.
When you use both Energy Saver and a screen saver program, the screen freezes.
The screen saver program may be conflicting with Energy Saver. Turn off
either the screen saver program or the Energy Saver control panel.
You see two resolution options labeled 640x870 (75 Hz).
If you’re using the Macintosh 24AC video card, you may see two apparently
identical resolution selections. The first option sets your monitor to display
millions of colors, and the second option sets your monitor to display 256
colors.
When you change resolutions, the monitor goes blank.
If your monitor is connected to the Macintosh 24AC video card, the monitor
may go blank for 15 seconds when you select a resolution that does not work
with your monitor. Try selecting another resolution.
38
Chapter 4
Appendix
Technical Information
Monitor features
m Multiple scan
m Resolution range: 640 x 480 to 1024 x 768
Screen
m 15-inch diagonal CRT, 13.75-inch diagonal viewable image size
m Antistatic, antiglare surface treatment
m 0.28 millimeter (mm) dot pitch
Input signals
m Red, green, and blue signals; separate sync
Power-saving feature
m Conforms to the Energy Star program of the United States Environmental
Protection Agency
m Power-saving feature compatible with the Video Electronics Standards
Association’s (VESA) Display Power Management Standard (DPMS)
39
User controls
m Power-on switch
m Automatic degauss at power-up; manual degauss by turning power switch
off, then on (capable of full degauss after monitor is turned off for 20
minutes or more)
m Buttons and controls: Select, Up, Down, brightness, contrast, sound
volume
m Additional picture controls available using the Select button: horizontal and
vertical shift, horizontal and vertical size
Active video image area
m Adjusted at the factory for the following standard modes:
Mode
Resolution
Vertical refresh rate
(hertz)
Horizontal scan rate
(kilohertz)
VGA
640 x 480
640 x 480
800 x 600
800 x 600
832 x 624
1024 x 768
60
31.77
35.0
37.9
48.1
49.7
60.2
Macintosh
SVGA
66.67
60
SVGA
72
Macintosh
Macintosh
75
75
Input electrical requirements
m Voltage
m Frequency
m Power
100–240 volts (V)
50/60 hertz (Hz)
75 watts (W) maximum
40
Appendix
Weight
m Approximately 30 pounds (13.5 kilograms)
Dimensions
m Height
m Width
m Depth
383 millimeters (mm) ± 5 mm
370 mm ± 5 mm
394.5 mm ± 5 mm
Interfaces
m Headphone/speaker: One input port and one pass-through output port
Temperature
Celsius (C) and Fahrenheit (F)
m Operating
m Storage
10˚ to 40˚ C (50˚ to 104˚ F)
0˚ to 60˚ C (32˚ to 140˚ F)
–40˚ to 65˚ C (–4˚ to 151˚ F)
m Shipping
Humidity (noncondensing)
m Operating
20% to 95%
Altitude
m Operating
0 to 10,000 feet (ft.)
0 to 3000 meters (m)
0 to 15,000 ft.
m Shipping
0 to 4500 m
41
Technical Information
Monitor cable specifications
m 15-pin miniature D-type connector
8
7
6
5
4
3
2
1
15 14 13 12 11 10 9
Pin
Output signal
1
Red video ground
Red video
Not used
2
3
4
ID 1
5
Green video
Green video ground
ID 2
6
7
8
Not used
9
Blue video
ID 3
10
11
12
13
14
15
Shell
V Sync return
V Sync
Blue video ground
H Sync return
H Sync
Shield ground
42
Appendix
Apple Computer, Inc.
1 Infinite Loop
Cupertino, California 95014-2084
408.996.1010
030-8471-A
Printed in Taiwan
|