|
SM523-G
Cup Holder Mount with Flexible Goosneck Shaft with Slim-Grip™ Smartphones
Package Contents:
SM050-2 Slim-Grip™
Universal Phone Holder
(1) GN033-SBH - 5” Cup holder mount with flexible gooseneck shaft
(1) SM050-2 Universal phone and portable device holder
(1) SP-SM050-LF - Extra Long Support Legs (2 Pack) for larger phones
Holder included is Universal, designed to fit nearly ALL non-flip mobile phones regardless of whether a
protective case or silicone sleeve is attached to the phone.
•
Most smartphones, mobile phones, and cell phones
having heights between 80mm and 138mm tall
Apple iPhone - All models
RIM BlackBerry - All non-flip models
HTC Phones - All non-flip models
•
•
•
•
•
•
•
Palm - All non-flip models
GN033-SBH
Cup Holder Mount
LG Mobile Phones - All non-flip models
Samsung - All non-flip models
Sony Ericsson - All non-flip models
Sanyo - All non-flip models
Pantech - All non-flip models
Google - All non-flip models
SP-SM050-LF
Extra Long
Support Legs
(2 Pack)
•
•
•
•
•
Motorola Phones - All non-flip models
Nokia Mobile Phones - All non-flip models
No tools required for installation.
Note: mount may not work with adjustable, “pop out” cup holders or oversize
cup holder openings found in full-size pickup trucks.
Do not place mount in or near an air bag deployment zone or where it
!
88mm expandable to 138mm
with Extra Long Support Legs
will obstruct view of the road.
All brand names and product names are trademarks or registered trademarks of their respective owners.
Install the Support Legs to the Holder
Cup Holder Mounting
Insert the holder support legs (A) by sliding them into the
Step 1.
Step 1.
Connect the gooseneck shaft (A) to the cup holder base (B) by
aligning the groove on the base to the ridge inside of the bottom
of the shaft.
support leg grooves (B) on the top and bottom of the holder.
B
A
(A) Cup Holder
Neck
A
(C) Thumb wheel
adjustment
knob
A
B
A
(B) Cup Holder Base
iPhone Holder Attachment
Step 2.
Step 3.
Place the Universal Cup Holder Mount into the designated cup
holder in the vehicle. Adjust the thumb wheel adjuster (C) to open
or close the cup holder prongs to fit in the cup holder.
Step 1.
Adjust the angle of the dual T head by tightening the adjustment
nut at the top of the cup holder shaft (A).
Step 2.
Install the iPhone holder to the shaft by inserting the dual T-tabs
(B) on the shaft into the T-slots (C) on on the back of the holder.
For oversize cup holder openings or the adjustable “pop out”cup
holders use the optional self-adhesive side support pads (D). Install
the pads by removing the adhesive backing and placing it on the
flat surface side of the cup holder support leg.
(B) Cup Holder
Shaft T-tabs
(A) Angle
Adjustment
Nut
OPEN
(D) Optional
(C) T-slots
support
CLOSE
pads
Safety Precautions
!
Do not install Arkon products over an air bag cover or within the air
bag deployment zone. Arkon Resources, Inc. assumes no responsi-
bility of liability for injury or death as a result of car crashes and/or
air bag deployment.
The Mobile Mounting Specialists™
Consumer Hotline:
Arcadia, CA 91006 USA
USA (800) 841-0884
INT’L (626) 254-9005
Monday - Friday 9am-5pm, PST
Designed in USA | Made in Taiwan & China
© Copyright 2010 Arkon Resources, Inc.
Arkon is not responsible for any damages caused to your car, your
device, or yourself due to the installation or use of this pedestal mount.
|