P/NO : 3828TUO197A (0203-Rev00)
Printed in Korea
Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A1
Important Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A2
Description of Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A4
Connecting the Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A6
Connection of external equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A8
On Screen Display (OSD) Control Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A9
On Screen Display(OSD) Selection and Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . .A10
Video Memory Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A14
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A15
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A16
i
Introduction
The FPD2200 Flat Panel Monitor has an active matrix TFT (Thin-Film
Transistor) LCD (Liquid Crystal Display).
Features
The FPD2200 is a 22-inch (55.8cm viewable) intelligent micro-processor based
monitor.
This monitor can be connected to a VCR or DVD. The monitor has two signal
connectors (D-sub and DVI-D) so that it can support both an existing analog
input (D-sub) and an advanced standard digital input (DVI-D). Two computers
can be simultaneously used while connected to this monitor.
This monitor has a picture-in-picture function so that you can watch from
VCR/DVD while using a computer.
The aspect ratio of the monitor is 16:10 so that you can feel as if you are
watching a film in a theater. You can also simultaneously display two pages of a
document set to an A4 size on the monitor, so that working efficiency can be
improved.
Digitally controlled auto-scanning is done with the micro-processor for horizontal
scan frequencies between 30 and 70kHz, and vertical scan frequencies
between 56 - 61Hz.
We accomplished to adapt the advanced design and technology to the monitor.
Soft touch buttons on the front panel are simple and allow you to conveniently
adjust a variety of image controls.
This monitor has DDC 2B function.
A1
Important Precautions
This unit has been engineered and manufactured to ensure your personal
safety, however improper use may result in potential e shock or fire hazards.
In order to allow the proper operation of all safeguards incorporated in this
display, observe the following basic rules for its installation, use, and
servicing.
On Safety
Use only the power cord supplied with the unit. In case you use another power
cord, make sure that it is certified by the applicable national standards if not being
provided by the supplier. If the power cable is faulty in any way, please contact the
manufacturer or the nearest authorized repair service provider for a replacement.
The power supply cord is used as the main disconnection device. Ensure that the
socket-outlet is easily accessible after installation.
Operate the display only from a power source indicated in the specifications of
this manual or listed on the display. If you are not sure what type of power supply
you have in your home, consult with your dealer.
Overloaded AC outlets and extension cords are dangerous. So are frayed power
cords and broken plugs. They may result in a shock or fire hazard. Call your service
technician for replacement.
Do not Open the Display.
There are no user serviceable components inside.
There are Dangerous High Voltages inside, even when the power is OFF.
Contact your dealer if the display is not operating properly.
To Avoid Personal Injury :
Do not place the display on a sloping shelf unless properly secured.
Use only a stand recommended by the manufacturer.
Do not try to roll a stand with small casters across thresholds or deep pile
carpets.
To Prevent Fire or Hazards:
Always turn the display OFF if you leave the room for more than a short period
of time. Never leave the display ON when leaving the house.
Keep children from dropping or pushing objects into the display's cabinet
openings. Some internal parts carry hazardous voltages.
Do not add accessories that have not been designed for this display.
During a lightning storm or when the display is to be left unattended for an
extended period of time, unplug it from the wall outlet.
A2
Important Precautions
On Installation
Do not allow anything to rest upon or roll over the power cord, and do not place
the display where the power cord is subject to damage.
Do not use this display near water such as near a bathtub, washbowl, kitchen
sink, laundry tub, in a wet basement, or near a swimming pool.
Displays are provided with ventilation openings in the cabinet to allow the release
of heat generated during operation. If these openings are blocked, built-up heat
can cause failures which may result in a fire hazard. Therefore, NEVER:
Block the bottom ventilation slots by placing the display on a bed, sofa, rug, etc.
Place the display in a built-in enclosure unless proper ventilation is provided.
Cover the openings with cloth or other material.
Place the display near or over a radiator or heat source.
Do not rub or strike the Active Matrix LCD with anything hard as this may scratch,
mar, or damage the Active Matrix LCD permanently.
Do not press the LCD screen with your finger for a long time as this may cause
some afterimages.
Some dot defects may appear as Red, Green or Blue spots on the screen.
However, this will have no impact or effect on the display performance.
If possible, use the recommended resolution to obtain the best image quality for
your LCD display. If used under any mode except the recommended resolution,
some scaled or processed images may appear on the screen. However, this is
characteristic of the fixed-resolution LCD panel.
On Cleaning
Unplug the display before cleaning the face of the display screen.
Use a slightly damp (not wet) cloth. Do not use an aerosol directly on the display
screen because over-spraying may cause electrical shock.
On Repacking
Do not throw away the carton and packing materials. They make an ideal
container in which to transport the unit. When shipping the unit to another
location, repack it in its original material.
A3
Description of Controls
Front Panel Controls
SET Button
Power Button
MENU Button
SOURCE
MENU
DOWN/UP
LEFT/RIGHT
SET
SOURCE Selection
Button
LEFT/RIGHT (
Buttons
)
DOWN/UP (
Buttons
)
Power Indicator
Control
Function
Use this button to select an input signal.
SOURCE
SOURCE Selection
Button
SOURCE
DOWN/UP
SET
INPUT SELECT
DVI DIGITAL
• DVI DIGITAL : DVI digital signal
• DSUB ANALOG : 15-pin D-sub analog signal
• V1(AV): Composite video
DSUB
ANALOG
V1 (AV)
(S)
V2
• V2(S): S video
MENU
MENU Button
Use this button to enter or exit the On Screen Display.
Use these buttons to choose or adjust items in the
On Screen Display.
DOWN/UP (
Buttons
)
DOWN/UP
LEFT/RIGHT
SET
Use these buttons to choose or adjust items in the
On Screen Display.
LEFT/RIGHT (
Buttons
)
SET Button
Use this button to enter a selection in the On
Screen Display.
Power Indicator
This indicator lights up green when the monitor
operates normally. If the monitor is in DPM (Energy
Saving) mode (stand-by/ suspend/power off), this
indicator color changes to amber.
Power Button
Use this button to turn the monitor on or off.
A4
Description of Controls
Rear Panel Controls
Connected to another object
(stand type and wall-mounted
type – optional)
DC15V
D
Locking slot
connected to a locking cable that
can be purchased separately at
most computer stores.
Composite Video
Input Jack
DC Power Connector
D-sub Connector
DC15V
S-Video
Video
IN
D
DVI-D Connector
S-Video Input Jack
A5
Connecting the Monitor
To set up the monitor, ensure that the power is turned off to the monitor,
computer system, and other attached devices. Connect the cables to the
monitor with it lying on a cushion or a cloth.
Follow these steps:
Using the Computer
1.
Connect the signal cable.
When connecting the DVI-D signal cable
.....Figure 1
Connect one end of the monitor signal cable to the input connector on the rear
panel of the monitor. Connect the other end to the DVI-D connector on the
1
rear panel of the computer and tighten the screws.
aligns with the DVI-D connector.
Be sure the signal cable
2
When connecting the D-Sub signal cable
.....Figure 2
Connect one end of the monitor signal cable to the input connector on the rear
panel of the monitor. Connect the other end to the D-Sub connector on the
1
rear panel of the computer and tighten the screws.
aligns with the D-Sub connector.
Be sure the signal cable
2
MAC Connect one end of the monitor signal cable to the input connector on
1
the rear panel of the monitor.
cable to the rear panel of Macintosh computer through a Macintosh adapter and
then tighten screws.
Connect the other end of the monitor signal
2'
Figure 1
DC Power
connector
DVI-D connector
There should be a
DVI - D port on
the computer
DC15V
S-Video Video
IN
D
3
1
5
DVI-D
2
4
AC adapter
Power Cord
Signal Cable
A6
Connecting the Monitor
DC Power
connector
D-sub connector
Figure 2
DC15V
S-Video Video
IN
D
3
1
5
D-sub
2
4
AC adapter
Power Cord
Signal Cable
Signal Cable
M
A
C
6
MAC Adapter
2'
2'
Note : The figure
shows the connection to an Apple Macintosh, using a separately
purchased adapter. For more information on adapter requirements, contact your
authorized dealer, reseller, or service provider.
2.
3.
Connect the plug from the AC adapter into the back of the monitor.
3
Connect one end of the AC power cord to the AC adapter
and the other end
4
to a properly grounded AC outlet that is easily accessible and close to the
5
monitor
.
A7
Connection of external equipment
Connecting the VCR/DVD
1.
Connect the audio/video output jacks of the VCR/DVD to the corresponding
input ports of the set.
If you connect the S-Video input port to external equipment, you can enjoy
high definition display.
• Monitor
RCA cable (optional)
S-Video
Video
IN
Y
• VCR/DVD
S-VIDEO
OUT
Y
S-Video cable (optional)
VIDEO
OUT
2.
Select an input signal.
SOURCE
DOWN/UP
SET
Press the SOURCE button on the front panel of the
monitor to select an input.
V1(AV): Composite video,
V2(S): S-video
INPUT SELECT
DVI DIGITAL
DSUB
ANALOG
V1 (AV)
(S)
V2
A8
On Screen Display (OSD) Control Adjustment
Making adjustments to the image size, position and operating parameters of
the monitor are quick and easy with the On Screen Display Control system.
A quick example is given below to familiarize you with the use of the controls.
Following section is an outline of the available adjustments and selections you
can make using the OSD.
NOTE
Allow the monitor to stabilize for at least 30 minutes before making image adjustment.
To make adjustments in the On Screen Display, follow these steps:
MENU
DOWN/UP
SET
LEFT/RIGHT
MENU
SET
DOWN/UP
Press the MENU Button, the main menu of the OSD will appear.
1
2
2
1
To access a control, use the DOWN/UP (
) Buttons. When the desired
control icon is highlighted, press the SET Button.
Press the DOWN/UP (
) Buttons to select the desired item.
) Buttons to adjust the item to the desired level.
3
4
4
3
Use the LEFT/RIGHT (
5
5
Accept the changes by pressing the SET Button.
Exit the OSD by Pressing the MENU Button.
6
6
A9
On Screen Display(OSD) Selection and Adjustment
You were introduced to the procedure of selection and adjusting an item
using the OSD system.
Listed below are the icons, icon names, and icon descriptions of the items that
are shown on the Menu.
Adjusting the Screen when Using a Computer
Note : When input is set as a digital signal, only the BRIGHTNESS, SETUP, and
PIP items can be adjusted. You do not need to adjust the other items.
OSD Adjust
Description
Brightness
Used to adjust the brightness of the
screen.
CONTRAST/BRIGHTNESS
Image
R G B
Color
Position
Tracking
Setup
PIP
Contrast
Adjust the display to the contrast
desired.
BRIGHTNESS 100
CONTRAST
100
RED / GREEN / BLUE
USER
COLOR ADJUSTMENT
Image
To set your own color levels.
R G B
Color
USER
9300K
6500K
RED
50
50
60
Position
Tracking
Setup
PIP
To appear the displays color
temperature.
• 9300K:Slightly bluish white.
• 6500K:Slightly reddish white.
9300K
6500K
GREEN
BLUE
IMAGE POSITION
Horizontal Position
To move picture image left and right.
Image
R G B
Color
Position
Tracking
Setup
PIP
Vertical Position
To move image up and down.
HORIZONTAL 50
VERTICAL 50
A10
On Screen Display(OSD) Selection and Adjustment
OSD Adjust
Description
AUTO
This function is suitable for analog
signal input only. This button is for the
automatic adjustment of the screen
position, clock and phase.
TRACKING
Image
R G B
AUTO
OFF
Color
CLOCK
PHASE
50
50
Position
Tracking
Setup
PIP
CLOCK
PHASE
To minimize any vertical bars or
stripes visible on the screen
background.The horizontal screen
size will also change.
To adjust the focus of the display.
This item allows you to remove any
horizontal noise and clear or sharpen
the image of characters.
Phase adjustment should be done
after adjusting the Clock.
LANGUAGE To choose the language in which the
SETUP
Image
control names are displayed.
LANGUAGE
ENGLISH
FULL
R G B
Color
IMAGE SIZE
OSD POSITION
TRANSPARENCY
BEEP
IMAGE SIZE This function displays the image in its
original size or enlarged size so as to
fit in the full screen of the LCD panel.
Position
Tracking
Setup
50
ON
ZOOM
OSD POSITION To adjust position of the OSD window
on the screen. Press the SET button
to display the submenu for OSD
POSITION.
1024 x 768 48.3 kHz / 60Hz
ELAPSED TIME 00000H
PIP
OSD POSITION
Image
R G B
Color
Position
Tracking
Setup
HORIZONTAL 50
VERTICAL
50
PIP
TRANSPARENCY
To adjust the transparency of the
OSD menu screen.
BEEP
To select beep on or off.
ZOOM
To adjust horizontal and vertical
image size simultaneously.
If you want to move the zooming
point, use the H/V POSITION function
in the sub-menu. However, if the
monitor turns off when zooming in
and out the screen, the monitor will
be returned to original screen.
ELAPSED It show how long the monitor has
been used.
TIME
A11
On Screen Display(OSD) Selection and Adjustment
OSD Adjust
Description
This PIP (Picture-in-Picture) function allows the
image from the VCR or DVD to be displayed on a
sub-screen while you are using a computer.
PIP
Image
R G B
PIP ON/OFF
OFF
Color
PIP SOURCE
PIP SIZE
V1 ( AV )
LARGE
Position
Tracking
Setup
PIP
PIP
ON/OFF
To select the sub-screen on/off.
PIP POSITION
PIP IMAGE
PIP
To select an input signal for PIP.
SOURCE :V1 (AV) / V2 (S)
PIP SIZE To adjust the size of the PIP screen.
:SMALL/MEDIUM/LARGE
PIP
To adjust the position of PIP screen.
POSITION Press the SET button to display the
submenu for PIP POSITION.
PIP POSITION
Image
R G B
Color
Position
Tracking
Setup
HORIZONTAL 50
VERTICAL
50
PIP
To adjust the image of the PIP screen;
Press the SET button to display the
submenu for PIP IMAGE.
PIP
IMAGE
Use the LEFT/RIGHT (
) buttons to
adjust the item to the desired level.
PIP IMAGE
Image
R G B
Color
PIP CONTRAST
PIP BRIGHTNESS
PIP SHARPNESS
PIP COLOR
53
70
50
50
50
Position
Tracking
Setup
PIP
PIP TINT
PIP CONTRAST
Adjust the display to the contrast desired.
PIP BRIGHTNESS
Used to adjust the brightness of the screen.
PIP SHARPNESS
To adjust the clearness of the screen.
PIP COLOR
To adjust the color to desired level.
PIP TINT
To adjust the tint to desired level. This function is
available only in NTSC broadcasting mode.
A12
On Screen Display(OSD) Selection and Adjustment
Adjusting the Screen when Using VCR/DVD ( V1 / V2 )
OSD Adjust
Description
CONTRAST Adjust the display to the contrast
ADJUSTMENT
Adjustment
Setup
desired.
CONTRAST
53
70
50
50
50
BRIGHTNESS Used to adjust the brightness of the
BRIGHTNESS
SHARPNESS
COLOR
screen.
SHARPNESS To adjust the clearness of the screen.
TINT
COLOR To adjust the color to desired level.
TINT
To adjust the tint to desired level.
This function is available only in
NTSC broadcasting mode.
To choose the language in which the
control names are displayed.
LANGUAGE
IMAGE SIZE
SETUP
ENGLISH
Adjustment
Setup
LANGUAGE
IMAGE SIZE
FULL
This function displays the image in
its original size or enlarged size so
as to fit in the full screen of the LCD
panel.
OSD POSITION
TRANSPARENCY
BEEP
0
ON
OSD POSITION
To adjust position of the OSD
window on the screen. Press the
SET button to display the submenu
for OSD POSITION.
OSD POSITION
Adjustment
Setup
HORIZONTAL 50
VERTICAL
50
TRANSPARENCY
To adjust the transparency of the
OSD menu screen.
BEEP
To select beep on or off.
A13
Video Memory Modes
The display modes listed below are the most commonly used modes and are
set as factory defaults. The monitor automatically recognizes most input data
modes, and displays centered images with the proper sizing.
If the screen size is inappropriately set or the display is not centered, you need
to readjust the parameters of the monitor using the OSD (on-screen display).
Display Modes (Resolution)
Display Modes (Resolution)
Horizontal Freq.(kHz)
Vertical Freq.(Hz)
1
2
3
4
5
6
7
31.469
35.156
37.879
48.363
60.000
63.981
64.350
VESA
VESA
VESA
VESA
VESA
VESA
640 x 480
800 x 600
800 x 600
1024 x 768
1280 x 960
1280 x 1024
1600 x 1024
60
56
60
60
60
60
60
A14
Troubleshooting
Check the following before calling for service.
Display Position is incorrect.
Select AUTO in the OSD menu.
If the results are unsatisfactory, adjust the image position using the position icon in
the on screen display.
On the screen background, vertical bars or stripes are visible.
Select AUTO in the OSD menu.
If the results are unsatisfactory, decrease the vertical bars or stripes using the
CLOCK icon in the on screen display.
Any horizontal noise appearing in any image or characters are not clearly
portraid.
Select AUTO in the OSD menu.
If the results are unsatisfactory, decrease the horizontal bars using the PHASE icon
in the on screen display.
Check signal Cable message.
The signal cable is not connected, or is loose. Check and secure the connection.
OUT OF RANGE message appears.
Picture is blank.
The frequency of the signal from the video card is outside the operating range of
the monitor.
Horizontal Frequency: 30kHz-70kHz
Vertical Frequency: 56Hz-61Hz
*Use the graphics board's utility software to change the frequency setting (Refer to the
manual for graphics board).
*
You can change the setup to the supported resolution using the Safe Mode (Press the F8
key during booting the system).
The power LED is illuminated amber.
The monitor is in its display power management mode.
There is no active signal coming from the PC.
The signal cable is not fastened securely.
Check the computer power and graphics adapter configuration.
The monitor doesn't enter the power saving off mode (Amber).
Computer video signal is not VESA DPMS standard. Either the PC or the video
controller card is not using the VESA DPMS power management function.
NOTE
If the power indicator(LED) light is blinking amber, may result in abnomal condition of
the monitor.
Then press a power ON/OFF button on the front panel control and call your service
technician for more information.
A15
Specifications
Display
Type
22inch (55.8cm) Wide SXGA TFT LCD
Anti-Glare coating
Viewable Size
Viewing Angle(max.)
Pixel pitch
22inch (55.8cm)
70˚ (Left/Right/Up/Down)
0.294 x 0.294mm
True color
16.7 million color
Sync Input
Video Input
Horizontal Freq.
Vertical Freq.
Input form
30kHz - 70kHz (Automatic)
56Hz - 61Hz (Automatic)
Separate, TTL, Positive/Negative
Digital
Signal input
Input Form
15 pin D-Sub connector/DVI-D connector
Separate, RGB Analog, 0.7Vp-p/75ohm, Positive
Digital
Resolution (max.)
Analog : 1600 x 1024 @ 60Hz
Digital : 1600 x 1024 @ 60Hz
Power
Consumption
Normal
Stand-by/Suspend ≤ 8
Power Off
≤
80W
W
8W
≤
Dimensions
Width
Height
Depth
58.2 cm / 22.9 inches
46.75 cm / 18.4 inches
7.3 cm / 2.87 inches
Power Input
AC Adapter
DC 15V 5.0A
Input
AC 100-240V, 50 /60Hz, ~1.5A
Output
DC 15V
5.33A
+
-
Weight
Net
14.8 kg / 32.6 lbs
Tilt Range
10˚~30˚
Environment
Conditions
Operating condition
Temperature
Humidity
10˚C to 35˚C
20% to 80% non-condensing
Storage condition
Temperature
Humidity
-20˚C to 60˚C
5% to 90% non-condensing
NOTE
Information in this document is subject to change without notice.
A16
|