3M™ SLiC 530/533/733-2 Port 0.61
Cable Entry Bracket
3M™ SLiC 530/533/733-2 Port-MSM 0.61
Cable Entry Bracket
For use with 3M™ SLiC™ Free-Breathing Fiber Optic
Closures and Terminals
Instructions
November 2011
78-8135-7466-8-B
3
3.0 Cable Addition Bracket Assembly Installation
3.1
Remove screw on the 3M™ Scotchlok™ Shield Bond
Connector 4464 and swing the plate to the side. If
the shield connector is installed with rivets, do not
perform this step.
3.2
Remove central strength member retainer. Unscrew
and remove the central strength member retainer that
is intended for use. If installed using rivets, do not
perform this step.
3.3
Loosen the second screw just enough to allow
the cable addition bracket to slide under the CSM
retainer. Replace the screw that was removed
previously and tighten the shield bond connector
tightening fastener between 25 to 30 in.-lbs.
(2.9 to 3.5 kgf-m).
78-8135-7466-8-B
3
™
™
4.0 Grommet Assembly Installation using the 3M Scotchlok 4460-D/FO-CSM
For LBT
4.1
Please refer to instruction manual 78-0013-
2695-4 3M Scotchlok Shield Bond Connector
Assembly 4460-D/FO-CSM for LBT for installation
instructions.
4.2
Assembly is now ready to place in the end seal of
the closure or terminal. Refer to instruction manual
document number 78-8135-4502-3 for end seal
installation.
™
™
5.0 Grommet Assembly Installation using the 3M Scotchlok Shield Bond
Connector 4460-D/FO
5.1
Please refer to instruction 78-8128-0289-6 3M
Scotchlok Shield Bond Connector Assembly 4460-D/
FO and 4460-D/FO-SS for installation instructions.
6.0 Installation into Closure or Terminal
6.1
Assembly is now ready to place in the end seal of
the closure or terminal. Refer to instruction manual
number 78-8135-4502-3 for end seal installation.
6.2
Place cable and grommet assembly onto cable
addition bracket such that the retention tab slips
between the two cables as shown.
Note Place the grommet and cable assembly such that a
minimum of 0.78"(19.8 mm) of cable jacket extends past
the hose clamp.
4
78-8135-7466-8-B
6.3
6.4
Using the supplied hose clamp, secure cables to the
cable addition bracket and cable management tray
frame as shown. Tighten hose clamp between 25 to
30 in.-lbs. (2.9 to 3.5 kgf-m).
If a single cable entry is also employed through
second endseal port, please refer to instruction
manual number 78-8135-4502-3 for cable installation
section 4.0.
78-8135-7466-8-B
5
3M, Scotch, Scotchlok and SLiC are trademarks of 3M Company.
Important Notice
All statements, technical information, and recommendations related to 3M’s products are based on information believed to be reliable,
but the accuracy or completeness is not guaranteed.Before using this product, you must evaluate it and determine if it is suitable for
your intended application. You assume all risks and liability associated with such use.Any statements related to the product which are not
contained in 3M’s current publications, or any contrary statements contained on your purchase order shall have no force or effect unless
expressly agreed upon, in writing, by an authorized officer of 3M.
Warranty; Limited Remedy; Limited Liability.
This product will be free from defects in material and manufacture for a period of one (1) year from the time of purchase.3M MAKES NO
OTHER WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE.If this product is defective within the warranty period stated above, your exclusive remedy shall be, at 3M’s option,
to replace or repair the 3M product or refund the purchase price of the 3M product.Except where prohibited by law, 3M will not be
liable for any indirect, special, incidental or consequential loss or damage arising from this 3M product, regardless of the
legal theory asserted.
3
Communication Markets Division
6801 River Place Blvd.
Austin, TX 78726-9000
1-800-426-8688
Please Recycle. Printed in USA.
© 3M 2011. All Rights Reserved.
78-8135-7466-8-B
|