RN-001031-00
Rev 00
Aastra CNX
Conference Network Switch
Release 1.3p1
February 2007
Aastra CNX
Conference Network Switch
1.3p1 Release Notes
Chapter 1
Changes and enhancements
Description
CNX Release 1.3p1 (aka 1.3.1) is an incremental patch release and delivers no
new feature functionality. It contains minor corrections to existing feature
operation, and hardware compatibility enhancements only.
Corrected issues
•
•
•
•
Corrected Windows user authentication for extended character set.
Added Windows XP firewall compatibility for FTP file transfers.
Extended the name recording buffer from 1.5 to 3 seconds.
Corrected the reply address used for conference booking emails.
Enhancements
•
•
Support added for 512MB CompactFlash cards - greenfield install required.
Support added for hardware PEC 80-0153-00 rev 07.
Note: CNX release 1.3 and earlier must not be loaded onto Rev07 or
newer units due to firmware incompatibility that will result in failure of
the system to boot. CNX 1.3p1 or later must be used on these units.
RN-001031-00, Rev 00 Rel. 1.3p1
1-1
Chapter 2
Updating the software
Description
The Update CNX Software tool in the Maintain CNX window allows you to
install software updates to the Aastra CNX.
The Aastra CNX software is packaged in a single file called “full_cnx.dra”.
This file will update both the CompactFlash and the onboard flash firmware.
You can place the full_cnx.dra file on your PC and use the Update CNX
Software button to install the update.
Procedure
Use the following procedure to update your Aastra CNX software.
Notes:
1. After port upgrades and major software releases on the Aastra CNX,
you must enter a new license key to activate the software.
2. The CNX performs an automatic reboot as part of the upgrade process.
RN-001031-00, Rev 00 Rel. 1.3p1
2-1
Aastra CNX Release Note 1.3p1
Step
Action
1
Open your Web browser and enter the URL for your Aastra CNX.
Log in with a valid user ID and password.
2
Click the Maintain CNX tab in the Aastra CNX main window.
Result: The Maintain Aastra CNX window displays.
Update CNX
Software
Save Configuration
CNX Operational
Status
3
4
In the “Manage System” section, click
configuration on the Aastra CNX.
to save the current
Click
and verify that there is sufficient disk space to upgrade
the Aastra CNX.
Note: The Aastra CNX requires approximately 35 MB or more of free disk space for an upgrade.
2-2
RN-001031-00, Rev 00 Rel. 1.3p1
Updating the software
Step
Action
5
In the “Status” section, click
.
Result: The following prompt displays.
6
Enter the location of the full_cnx.dra file in the text box.
or
Click
.
The Select File window displays.
Navigate to the location of the full_cnx.dra file and click OPEN to automatically place it in the text
box of the Browse window.
RN-001031-00, Rev 00 Rel. 1.3p1
2-3
Aastra CNX Release Note 1.3p1
Step
Action
7
Click
.
Result: The full_cnx.dra file proceeds to download to your Aastra CNX CompactFlash card.
You will be prompted to confirm that a reboot can occur. The reboot will initiate the upgrade
process, which may take up to 15 minutes to fully update the onboard flash firmware and the
compactflash root filesystem.
You will be unable to log into the CNX webinterface until the upgrade is fully complete.
Progress can be monitored using the serial console, if connected. When the upgrade is
complete, the following message displays on the console:
“Upgrade of the Aastra CNX is complete”.
8
9
Close and then open your Web browser and enter the URL for your Aastra CNX.
Log in with a valid user ID and password.
Click on the Maintain CNX tab.
Result: The Maintain Aastra CNX window displays.
2-4
RN-001031-00, Rev 00 Rel. 1.3p1
Updating the software
Step
Action
10
In the “Status” section, click
and verify the following:
•
There is sufficient disk space for the operation of the Aastra CNX.
Note: The Aastra CNX requires approximately 35 MB or more of free disk space to operate
properly. If there is insufficient disk space, click “CLEANUP CNX” to delete unwanted files on
the CompactFlash.
•
•
There are no PRI alarms.
The Aastra CNX is accepting the following types of calls:
—
—
—
PRI calls (including alarms on active PRI lines)
SIP calls
H.323 calls
11
12
Click the Permanent Conferences or Scheduled Conferences tab to perform the following:
•
•
Verify that previous permanent and scheduled conferences are still present after the
upgrade.
Schedule new conferences with AND without a moderator to verify:
- that conferences can be created successfully.
- that moderators and users can join the conferences.
After port upgrades and major software releases, enter a new license key using the procedure
defined in the Aastra CNX Administrator’s Guide, Chapter 5, the section “Entering/editing
License Key.”
Note: If any of the steps in the previous Update Procedure results in an
error, contact your reseller for help first. Alternatively, you can contact
Aastra Telecom Technical Support.
RN-001031-00, Rev 00 Rel. 1.3p1
2-5
Aastra CNX
Conference Network Switch
1.3p1 Release Notes
Published in the USA
RN-001031-00 Rev 00
Aastra CNX Conference Network Switch Release 1.3p1
February 2007
|