DISTRIBUTION AMPLIFIERS
MANUAL PART NUMBER: 400-0155-002
DA1921SX
CAT-5 COMPUTER VIDEO
RECEIVER
USER’S GUIDE
DISTRIBUTION AMPLIFIERS
· To turn off the main power, be sure to remove
the adapter from the power outlet. The power
outlet socket should be installed as near to the
equipment as possible, and should be easily
accessible.
PRECAUTIONS / SAFETY WARNINGS
1
Please read this manual carefully before using your
DA1921SX. Keep this manual handy for future
reference. These safety instructions are to ensure
the long life of your DA1921SX and to prevent fire
and shock hazard. Please read them carefully and
heed all warnings.
· Do not pull the adapter or any cable that is
attached to the DA1921SX.
· If the DA1921SX is not used for an extended
1.1 GENERAL
period, disconnect the adapter from the outlet.
· Unauthorized personnel shall not open the unit
1.4 CLEANING
since there are high-voltage components inside.
· Unplug the DA1921SX (adapter or cord) before
cleaning. Clean surfaces with a dry cloth. Never
use strong detergents or solvents, such as
alcohol or thinner. Do not use a wet cloth or
water to clean the unit.
· Qualified ALTINEX service personnel, or
authorized representatives, must perform all
service.
1.2 GUIDELINES FOR RACK-MOUNTING
1.5 FCC / CE NOTICE
· Maximum operating ambient temperature is
35 (degrees C).
· This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions: (1) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired operation.
· When installing equipment into a rack, distribute
the units evenly. Otherwise, hazardous conditions
may be created by an uneven weight distribution.
· Connect the unit to a properly rated supply
circuit.
· This equipment has been tested and found to
comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable
protection against harmful interference when the
· Reliable Earth Grounding of Rack-Mounted
Equipment should be maintained.
1.3 INSTALLATION
· For best results, place the DA1921SX on a flat,
level surface in a dry area away from dust and
moisture.
equipment is operated in
a
commercial
environment. This equipment generates, uses,
and can radiate radio frequency energy and, if
not installed and used in accordance with the
instruction manual, may cause harmful
interference to radio communications. Operation
of this equipment in a residential area is likely to
cause harmful interference in which case the
user will be required to correct the interference at
their expense.
· To prevent fire or shock, do not expose unit to
rain or moisture. Do not place the DA1921SX in
direct sunlight, near heaters or heat radiating
appliances, or near liquid. Exposure to direct
sunlight, smoke, or steam can harm components.
· Handle the DA1921SX carefully. Dropping or
jarring can damage internal components.
· Do not place heavy objects on the DA1921SX. If
the DA1921SX is mounted to a table or wall, use
only ALTINEX-made mounting accessories, such
as the mini-brackets MB1001 and cables for
optimum setup.
· Any changes or modifications to the unit not
expressly approved by ALTINEX, Inc. could void
the user’s authority to operate the equipment.
400-0155-002
2
DISTRIBUTION AMPLIFIERS
ABOUT YOUR DA1921SX
The DA1921SX is a high-resolution 1-in 2-out
computer video amplifier/receiver. It converts
2
MECHANICAL
Material
Finish
Top Panel
Height (inches)
Width (inches)
Depth (inches)
Weight (pounds)
Ship Weight (pounds)
T° Operating
T° Maximum
Humidity
DA1921SX
0.1” Al
ALTINEX Grey
Lexan Overlay
3.00in (76mm)
4.50in (114mm)
1.00in (25mm)
0.40lb (0.18kg)
2.4lbs (1.09kg)
10°C-35°C
differential signals from a CAT-5 transmitter to
single ended video signals. These single ended
signals allow the source to be distributed to large
screen projectors or other displays with excellent
quality at long distances. The DA1921SX is
designed to be used together with a compatible
CAT-5 computer video transmitter, such as model
DA1920SX. The DA1921SX is connected to the
transmitter using twisted pair CAT-5 UTP
(Category 5, 5e, 6) type cable.
50°C
90% non-condensing
MTBF (calculations)
40,000 hrs
The DA1921SX is compact and easy to use. It
offers a CAT-5 input, two fully buffered outputs and
equalization control. It is perfect for audio/visual
installations, where a single computer sends
signals using inexpensive, thin, light CAT-5 cable.
Table 2. DA1921SX Mechanical
ELECTRICAL
DA1921SX
Input Video Signal
Analog Signal Level
Differential ±0.75V
max
The DA1921SX can receive signal resolutions from
VGA thru UXGA. Together with an ALTINEX
CAT-5 computer video transmitter and properly
adjusted with the built-in equalization controls, the
maximum cable distance is approximately 500
feet/152 meters for VGA (640 x 480, 60 Hz refresh
rate) and 250 feet/76.2 meters for UXGA (1600 x
1200, 60 Hz refresh rate). Please see the complete
specifications for other resolutions.
Impedance
50 Ohms
Input Sync Signal
Horizontal, Vertical, & C-Sync
Impedance
Output Video Signals
Analog Signal Level
Fall/Rise Time (ns)
Impedance
Differential ±1V
50 Ohms
1.5V p-p
2.0
75 Ohms
Output Sync Signals
Horizontal Sync
Vertical Sync
Coupling
Cross-talk
TTL (+/-)
TTL (+/-)
TECHNICAL SPECIFICATIONS
3
FEATURES/DESCRIPTION
GENERAL
Inputs
Input Connector
Outputs
DA1921SX
AC
-40 dB @ 10 MHz
One
RJ-45
Two
Power
External Power Adapter
9V DC, 500 mA
Table 3. DA1921SX Electrical
Local Monitor Connector
Main Output Connectors
Cable Distance Limitations
Signal Resolution Distance
15-pin HD Female
15-pin HD Female
NOTE: All cables for the DA1921SX must be
640 x 480: 500ft/152m
800 x 600: 450ft/137m
1024 x 768: 400ft/122m
1280 x 1024: 350ft/107m
1600 x 1200: 250ft/76m
VGA thru UXGA
ordered separately.
Compatibility
Table 1. DA1921SX General
400-0155-002
3
DISTRIBUTION AMPLIFIERS
PRODUCT DESCRIPTION
4
400-0155-002
4
DISTRIBUTION AMPLIFIERS
4.1 INPUT
4.2 OUTPUTS
The input connector of the DA1921SX is an RJ-45
connector, which connects the DA1921SX to the
DA1920SX using a CAT-5 cable.
The DA1921SX has two outputs with 15-pin HD
female connectors. It allows the distribution of
video signals to two monitors. With equalization,
the DA1921SX receives signals through
a
CAT-5 cable from as far as 500 feet away.
Input Signals
PIN No.
RJ-45 Connector
Output Signals
PIN No.
1
2
3
4
5
6
7
8
R-
R+
G-
B-
B+
G+
HOR-
HOR+
15-pin HD Female
1
2
Red
Green
3
Blue
4
ID Bit 4
5
Ground
6
Ground
7
Ground
Table 4. DA1921SX Input Signals
8
Ground
9
+5V
10
11
12
13
14
15
Ground
Ground
No Connection
Horizontal Sync
Vertical Sync
No Connection
Table 5. DA1921SX Output Signals
APPLICATION DIAGRAM
5
400-0155-002
5
DISTRIBUTION AMPLIFIERS
7.1 LED INDICATOR
INSTALLING YOUR DA1921SX
6
The DA1921SX offers a special LED on the
front panel that provides feedback to the user.
When power is connected to the DA1921SX,
the LED will turn Red. When a valid CAT5
source is connected to the DA1921SX, the LED
will turn Green, indicating that it is receiving a
signal by sensing the presence of the sync
portion of the signal.
Step 1. Connect the 9V 500mA AC adapter’s
output plug to the DA1921SX’s power
input connector - 2.5 mm DC Jack. Verify
that the RED power LED turns ON.
Step 2. Remove the protective port covers.
Connect the video output from the
DA1920SX to the input connector on the
DA1921SX using the CAT-5 cable.
7.2 EQUALIZATION
The DA1921SX provides an equalization
adjustment for long cable runs. Cable runs less
than 50 feet in length will require little to no
equalization. After that, the longer the cable,
the more equalization is required.
Step 3. Verify that the red LED on the face of the
unit has now turned green, indicating an
active source. If the LED is not green, the
DA1920SX may not be sending video
signals.
In some cases, it will be necessary to adjust the
equalization on both the transmitter and
receiver.
Step 4. Connect one or two monitors (as needed)
to the output connectors using the
appropriate VGA cable.
TROUBLESHOOTING GUIDE
8
Step 5. Verify that the picture quality on Monitors
1 and 2 (connected to Output 1 and
Output 2 of the DA1921SX) is good. If
you are not receiving a signal, make sure
that the display is compatible with the
resolution of the computer graphics card.
Note: High levels of static discharge
under some conditions may shutdown the
unit. To reset the unit simply, disconnect
the input cable and reconnect it back.
We have carefully tested and have found no
problems in the supplied DA1921SX. However, we
would like to offer suggestions for the following:
8.1 LED IS NOT RED
The LED should be ON and RED when power is
applied and there is no video signal present. If
the LED is ON and GREEN, the unit is receiving
power and a SYNC signal.
Cause 1: No AC power.
OPERATION
7
Solution: Verify the adapter is plugged into a
working AC outlet and that the outlet
has power.
There is only one adjustment necessary to operate
the DA1921SX. The adjustment is for equalization
on long cable runs. It is adjustable according to the
cable length. The unit will operate successfully as
long as cables are attached properly and other
technical specifications are followed.
Cause 2: Adapter is not plugged into
DA1921SX.
Solution: Verify the DC power plug coming
from the AC adapter is plugged all
the way into the DA1921SX.
400-0155-002
6
DISTRIBUTION AMPLIFIERS
In general, cable runs less then 50
feet require little or no video
equalization and should be set to
minimum. Longer cable runs will
require equalization on both the
transmitter and receiver.
Cause 3: The DA1921SX has a problem.
Solution: If there is AC power to the adapter
and the LED still does not turn on,
the DA1921SX or the power adapter
may require service. Call ALTINEX
at (714) 990-2300.
8.4 REMOTE IMAGE QUALITY IS POOR
Cause 1: The source has a problem.
8.2 LED IS NOT GREEN
Cause 1: There is no power.
Solution: Check the image on the local
monitor and verify the quality is
good. If the local image is good, see
Cause 2.
Solution: Disconnect the video input from the
DA1921SX and verify the LED is ON
and RED indicating power is
present. Reconnect the computer's
video output. If the LED is still not
GREEN see Cause 2.
Cause 2: Video equalization required.
Solution: Adjust the VIDEO EQUALIZATION
on the DA1921SX. Long cable runs
may require adjustment on both the
DA1921SX and the DA1920SX. If
the image is still not correct, call
ALTINEX at (714) 990-2300.
Cause 2: There is no Sync signal.
Solution: Verify the computer output is
operating correctly by connecting it
directly to the local monitor,
bypassing the transmitter and
receiver. If the display is good, call
ALTINEX at (714) 990-2300.
ALTINEX POLICY
9
9.1 LIMITED WARRANTY/RETURN POLICY
8.3 NO REMOTE IMAGE
Please
see
the
Altinex
website
at
Cause 1: The source has a problem.
www.altinex.com for details on warranty and
return policy.
Solution: Check the image on the local
monitor and verify the quality is
good. If the local image is good, see
Cause 2.
9.2 CONTACT INFORMATION
ALTINEX, INC
Cause 2: Video equalization required.
592 Apollo Street
Solution: Adjust the VIDEO EQUALIZATION
on the DA1921SX. Long cable runs
may require adjustment on both the
DA1921SX and the DA1920SX.
Brea, CA 92821 USA
TEL: 714 990-2300
TOLL FREE: 1-800-ALTINEX
WEB: www.altinex.com
E-MAIL: [email protected]
400-0155-002
7
|