Installation
Instructions
MOMENTS
BATH/SHOWER TRIM KIT
T506.50X
Thank you for selecting American-Standard...the benchmark
of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--please
read these instructions carefully before you begin.
Certified to comply with ANSI A112.18.1
M968951 Rev. 1.4
Recommended Tools
Flat Blade Screwdriver
Adjustable Wrench
Plumbers' Putty or Caulking
Channel Locks
Pipe Wrench
Phillips Screwdriver
ROUGHING-IN DIMENSIONS
To assure proper positioning in relation to wall, note
roughing-in dimensions.
3/4"" TO 2-3/8"
INLETS
FINISHED WALL
INLETS
4-1/16"
1/2" NOM.
COPPER
SHR. 1/2" NOM.
1/2" NPT
SWEAT
COPPER SWEAT
SWEAT
INLETS
2"
5-5/8" REF.
2-3/8"
4-1/16"
OPTIONAL TO FINISHED
TUB 1/2" NOM.
COPPER SWEAT
FLOOR USUALLY
BETWEEN 65'' AND 80''
8-1/8" REF.
"SEE ILLUSTRATION "
SWEAT
INLETS (STOPS)
5-7/8"
74" FOR
HEAD CLEARANCE
SHR. 1/2" NOM.
COPPER SWEAT
4-1/16"
SHR
TUB
8-3/8"
TUB 1/2" NOM.
COPPER SWEAT
INLETS
1/2" NOM.
COPPER
SWEAT
18"
OPTIONAL
OUTLETS
1/2" NPT
INLETS 1/2" NPT
6-1/2"
3-3/8"
5-7/8"
1/2" NPT
3-3/8"
1-1/2" REF.
TOP OF
TUB RIM
4"
OUTLETS
1/2" NPT
3-3/8"
INLETS
BOTTOM OF
TUB
1/2" NPT
THREADED INLETS
THREADED INLETS (STOPS)
CARE INSTRUCTIONS:
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A
CLOTH WITH A COARSE SURFACE.
ADJUST HOT LIMIT STOP
3
"RED RING"- HOT
LIMIT SAFETY STOP
HOT LIMIT SAFETY STOP ADJUSTMENT
By restricting handle rotation and limiting the amount
of hot water allowed to mix with the cold, the HOT LIMIT
SAFETY STOP reduces risk of accidental scalding. To set
the maximum hot water temperature of your faucets, all
you need to do is adjust the setting on the HOT LIMIT
SAFETY STOP.
1
"A"
"A"
"B"
ADJUSTMENT WHEN
WATER IS TOO HOT
"B"
Use a flat blade screwdriver or your fingers to pull
up and rotate red HOT LIMIT SAFETY STOP (1).
Follow Step "A" or "B" to adjust min./max. discharge
temperature. "0" being the hottest to "7" the coldest
temperature setting. Factory set at "0".
ADJUSTMENT WHEN
WATER IS TOO COLD
PRY RED RING
FORWARD AND ROTATE
COUNTER-CLOCKWISE
ONE CLICK
TEMPERATURE
SETTING
NUMBERS
PRY RED RING
FORWARD AND
ROTATE CLOCKWISE
HANDLE INSTALLATION
INSTALL ADAPTER SCREW
4
4a
INSTALL HANDLE ADAPTER
With a flat blade screwdriver thread ADAPTER SCREW (4) into
HANDLE STEM ADAPTER (1) and tighten.
Push HANDLE ADAPTER (1) onto VALVE STEM (2).
Tighten set screw (3) with 2.5mm hex wrench
supplied.
2
1
1
3
4
2.5MM HEX
WRENCH
INSTALL HANDLE
4c
Align HANDLE (6) and install onto
HANDLE ADAPTER ASSEMBLY (7).
Tighten set screw (8) with 2.5mm
hex wrench supplied to secure HANDLE.
INSTALL ADPATER
4b
Push PLUG BUTTON (9)
into set screw access hole
in HANDLE (6).
With a flat blade screwdriver thread ADAPTER (5)
onto SET SCREW (4) and tighten.
7
8
9
6
2.5MM HEX
WRENCH
5
4
SERVICE
5
5
4
If faucet drips, operate handle several times
from "off" to "on". Do not apply excessive force.
Clogged CARTRIDGE (4) inlets may cause reduced
flow in "full on" hot or cold. To clean inlets, first turn
off water supply, then:
CARTRIDGE
INLETS
Remove HANDLE (1), CAP (2) and CARTRIDGE (4).
Clean inlets and MANIFOLD (5).
Reassemble CARTRIDGE (4), alternately tightening
SCREWS (3). Replace CAP (2) and HANDLE (1).
Check flow.
3
2
1
M968951 Rev. 1.4
|