ULTRA ACOUSTIC MODELER AM400
Thank you for showing your confidence in us by purchasing the BEHRINGER ULTRA ACOUSTIC
MODELER AM400. This high-quality modelling effects pedal is designed for all electric guitar players
who want to add incredibly realistic acoustic guitar sounds to their playing. Thanks to its Real Sound
Modeling (RSM) technology that combines state-of-the-art DSP technology with sophisticated algorithms
to emulate real acoustic environments, you can create everything from standard, large-resonant,
brilliant to bright Piezo pickup simulations.
1. CONTROLS
Top view
The LEVEL control adjusts the output level of the effect.
The REVERB control adjusts the amount of reverb effect that can be added to the signal.
The RES(onance) control adjusts the resonance of the simulated acoustic guitar body.
The ATTACK control adjusts the amount of attack and harmonic content of the high frequencies.
The MODE control lets you choose between four different acoustic modes:
STANDARD produces a typical acoustic guitar sound.
LARGE delivers a large, more resonant acoustic.
PIEZO simulates the distinct brightness of a classic piezo pickup.
BRIGHT gives you a brilliant and ultra-present sound, perfect for cutting through in a live environment.
The ON/BATT-LED illuminates when the effect is activated. It also serves as a battery level
indicator.
Use the footswitch to activate/deactivate the effect.
Use this 1/4" TS IN connector to plug in the instrument cable.
This is the 1/4" TS OUT connector. When you only use this output, it carries the affected signal
when the effect is active, and the direct signal (without effect) when the effect is inactive—both
optimized for connecting to guitar amplifiers. When both the OUT and the DIR OUT (see
)
connectors are used, the OUT connector carries the affected signal optimized for connecting to
a mixer/PA when the effect is active. When the effect is inactive the OUT connector is muted.
This is the 1/4" TS DIR OUT connector, which is muted when the effect is active. When inactive
it carries the direct signal (without effect) optimized for connecting to guitar amplifiers. It works
the same way, when both the DIR OUT and the OUT (see
) connectors are used.
Use the DC IN connection to plug in a 9 V power supply (not included).
The BATTERY COMPARTMENT is located underneath the pedal cover. To install or replace the 9 V
battery (not included), press the hinges with a ballpoint pen and remove the pedal cover. Be careful
not to scratch the unit.
ꢀ
The AM400 has no on/off switch. As soon as you insert the jack into the IN connector, the
AM400 begins running. When not using the AM400, remove the jack from the IN connector.
This extends the life of the battery.
The SERIAL NUMBER is located on the underside.
ꢀ
In rare cases interferences of the normal function may appear by external influence (e.g.
electrostatic discharge), as for example sound disturbances or malfunctions. If this
occurs, please turn down the volume on subsequent amplifiers and disconnect the
input connector briefly to restart the application.
FEDERAL COMMUNICATIONS
COMMISSION COMPLIANCE
INFORMATION
ULTRA ACOUSTIC MODELER AM400
Responsible party name:
Address:
MUSIC Group Services USA, Inc.
18912 North Creek Parkway,
Suite 200 Bothell, WA 98011,
USA
Phone/Fax No.:
Phone: +1 425 672 0816
Fax: +1 425 673 7647
ULTRA ACOUSTIC MODELER AM400
complies with the FCC rules as mentioned in the following paragraph:
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC rules. Operation is subject to the
following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may
cause undesired operation.
Important information:
Changes or modifications to the equipment not expressly approved by MUSIC Group
can void the user’s authority to use the equipment.
behringer.com
|