C50ic
C60ic
C62ic
C80ic
owner's manual
analog and digital systems
may be above the ceiling. This facing is a moisture barrier. Use duct tape or wide vinyl tape to seal
any cuts.
Keep debris and loose material away from the installation location. Do not allow debris to get in
the openings of the woofer basket. Debris and loose material can cause buzzing or rattling, and can
damage the woofer cone. Install plastic or fiberglass screening above the speaker to keep debris
away. Handle the speaker carefully.
Do not let anything touch the speaker cone or dome. Do not clean the speaker with paint thinner
or any solvents.
•
Consider the services of a professional custom installer. If you have any doubts about your own
abilities, it is better not to risk damaging your walls or ceilings, electrical wiring, ventilation ducts
or plumbing.
•
•
•
Work with good quality, correct tools. This will save you time and assure superior results.
Allow sufficient clearance.
When using speakers outdoors, locations should be sheltered from direct sunlight, rain or snow.
Direct exposure will shorten product life.
•
Combined impedance for speakers connected to each channel must be at least 4 ohm. This is the
minimum impedance tolerated by most amplifiers. Check with your dealer before wiring multiple
speaker pairs.
general mounting suggestions
Avoid placing the speaker within two feet (0.6 meters) of a corner. The acoustic reflections from surfaces
near the speakers can detract from the sound quality. Do not place the speaker behind heavy fabrics; if
you cannot see through a fabric, you cannot hear through it.
The ceiling speakers are designed for "infinite baffle" operation. The area behind the speaker installation
should be at least one-half cubic foot in volume to ensure proper performance. If the area is too small it
will limit bass response and cause a peak in the mid-bass range.
The panel on which the speaker is mounted must be rigid. There must not be any air leaks between the
area behind the speaker and the listening area.Mounting the speaker on a panel of a suspended ceiling
will adversely affect its performance.
3
prewiring
•
•
•
•
•
•
Check local building and electrical codes for compliance of the speaker wire.
Use stranded wire of at least 16 gauge; for runs over 100 feet, it is preferable to use 14 gauge wire.
Use only insulated staples or nylon tie straps to secure wiring within the wall to avoid shorts.
Do not stretch the wire as it is being routed. This could create future (and costly) problems.
Leave about 2-3 feet of free wire at both ends. Cutting excess wire is better than splicing.
Always "home run" wires: run a continuous wire from each speaker directly to the source location.
Do not connect speakers together any other way for easier diagnosis of faulty wire or speaker problems.
•
•
The C62ic stereo speakers require 2 speaker wires per speaker.
Wire speakers in phase with the same polarity. Attach positive (+/red) and negative (-/black) terminals
consistently.
•
Combined impedance for speakers connected to each channel must be at least 4 ohm. This is the
minimum impedance tolerated by most amplifiers. Check with your dealer before wiring.
preparing the wall or ceiling cutout
Confirm there is at least 1" between the final cutout and nearby studs or joints for positioning
mounting hardware. Temporarily fasten the stiff paper template (supplied) to the wall with
thumbtacks. Carefully trace around the perimeter with a pencil. Before making the final cutout
of the entire hole, first make a small 4-inch"test" cutout in the center of your penciled outline.
Reach your hand inside to verify that studs are outside the outline. This is an important step,
since stud finders are not infallible.
To cut the actual hole, first score wallboard with a sharp knife; then use a keyhole saw to
complete the cut. Remove remaining debris from the edges. Hold the speaker up to the cutout
to make sure it inserts easily without forcing.
At this point, it is a good idea to secure the speaker wire(s) to a stud near the cutout so its own
weight will not tug on the terminals of the speaker after it is connected. This will also prevent
you from "losing" the wire in the ceiling. Before attaching the wire(s), make sure the speaker
wire(s) runs through, not around, the metal mounting bracket.
installation preparation
Use the supplied template to outline the mounting hole. Cut the mounting hole and remove any
debris from the area. Take the necessary steps to keep debris from falling into the back of the speaker.
Route the wire(s) from the amplifier to the speaker installation location. Connect the speaker
wire(s) to the color-coded terminals. Strip about 1/2" of the insulation from the wire conductors.
Twist the wire strands of the conductors into neat bundles. Insert wire(s) into wire holes on speaker
plugs and tighten set screws. Plug speaker plugs into crossover terminals on the PC board.
4
final installation
The speaker is held in place with four mounting clamps that are part of the assembly. When
shipped from the factory the clamps are pivoted so they will fit into the mounting hole. When
the mounting hole clamp screws are turned, the clamps pivot outward and are then drawn
downward until they press against the back of the mounting surface.
Insert the speaker/mounting bezel assembly into the mounting hole. Hold the speaker in place
in the mounting hole and evenly tighten the four mounting screws to draw the mounting
brackets against the backside of the wall. Gradually tighten the screws, moving from one to
another, until the speaker is firmly clamped in place.
custom painting
•
•
Paint the speaker frame and grill before mounting to the wall; paint grill and frame separately.
Before painting, mask the recessed area of the speaker to completely protect the speaker
drivers.
•
After painting the grill, gently blow through its perforated holes to prevent paint clogging.
operation
checking the system
Listen carefully to each speaker. If you hear buzzing or rattling noises, remove the speaker and
check for a speaker wire(s) or other objects touching the speaker assembly. When you are
satisfied with the installation press the grills into place.
tweeter protector
If a speaker sounds "dull", or "lacks "brilliance", you may have activated the tweeter protector.
If high power operation causes the tweeter to stop playing, turn down the volume control until
normal sound resumes.
5
specifications
C50ic
C60ic
C62ic
C80ic
(Stereo)
Frequency response (Hz)
impedance
81-20kHz
8 ohm
57-20kHz
8 ohm
65-20kHz
8 ohm x 2
87dB
52-20kHz
8 ohm
Sensitivity 1W/1M (dB)
max bezel diameter
mounting hole
rear clearance
86dB
87dB
88dB
8 1/16"
6 9/16"
2 5/8"
9"
9"
10 11/16"
9 7/16"
3 5/8"
7 3/4"
7 3/4"
3 1/4"
3 1/4"
recommended power
Woofer
20-80watts
5 1/4"
20-80watts
6 1/2"
20-80watts x 2
6 1/2"
20-80watts
8"
Tweeter
3/4" dome
3/4" dome
1" dome X 2
1" dome
(Specifications subject to change without notice)
6
warranty information
LIMITED FIVE YEAR CONSUMER WARRANTY FOR PRODUCT INSTALLED BY AN AUTHORIZED
LICENSED DEALER
Directed Electronics, Inc. promises to the original purchaser, to replace this product should it prove to be
defective in workmanship or material under normal use, for a period of five years from the date of
purchase from the dealer as indicated by the date code marking of the product PROVIDED the product
was sold by an authorized Directed dealer. During this five year period, there will be no charge for this
replacement PROVIDED the unit is returned to Directed, shipping pre-paid. This warranty is non-
transferable and does not apply to any unit that has been modified or used in a manner contrary to its
intended purpose, and does not cover damage to the unit caused by installation or removal of the unit.
This warranty is void if the product has been damaged by accident or unreasonable use, neglect, improper
service or other causes not arising out of defects in material or construction. Units which are found to be
damaged by abuse resulting in thermally damaged voice coils are not covered by this warranty but may
be replaced at the absolute/sole discretion of Directed. ALL WARRANTIES INCLUDING BUT NOT
LIMITED TO EXPRESS WARRANTY, IMPLIED WARRANTY, WARRANTY OF MERCHANTABILITY,
FITNESS FOR A PARTICULAR PURPOSE , AND WARRANTY OF NON-INFRINGEMENT OF
INTELLECTUAL PROPERTY ARE EXPRESSLY EXCLUDED AND DISCLAIMED TO THE MAXIMUM
EXTENT ALLOWED BY LAW, AND DIRECTED NEITHER ASSUMES NOR AUTHORIZES ANY PERSON
TO ASSUME FOR IT ANY LIABILITY IN CONNECTION WITH THE SALE OF THE PRODUCT. DIRECTED
HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALL ACTS OF THIRD PARTIES INCLUDING ITS
AUTHORIZED DEALERS OR INSTALLERS. Unit must be returned to Directed, postage pre-paid, with bill
of sale or other dated proof of purchase bearing the following information: consumer.s name, telephone
number, and address, authorized dealer.s name and address, and product description. Note: This warranty
does not cover labor costs for the removal and reinstallation of the unit. IN ORDER FOR THIS
WARRANTY TO BE VALID, YOUR UNIT MUST BE SHIPPED WITH PROOF OF SALE BY AN
AUTHORIZED DIRECTED DEALER. Some states do not allow the limitation on how long an implied
warranty lasts, so the above limitation may not apply to you. LIMITATION OF DAMAGES AND
LIABILITY: CONSUMER.S REMEDY IS LIMITED TO REPAIR OR REPLACEMENT OF THE UNIT, AND IN
NO EVENT SHALL DIRECTED.S LIABILITY EXCEED THE PURCHASE PRICE OF THE UNIT. IN ANY
EVENT, DIRECTED SHALL NOT BE LIABLE FOR ANY DAMAGES (INCLUDING, BUT NOT LIMITED TO,
ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, PUNITIVE OR CONSEQUENTIAL DAMAGES, LOST
PROFITS, LOST SAVINGS, OR, TO THE EXTENT ALLOWED BY APPLICABLE LAW, DAMAGES
RESULTING FROM DEATH OR INJURY ARISING OUT OF OR IN CONNECTION WITH THE
INSTALLATION, USE, IMPROPER USE, OR INABILITY TO USE, THE PRODUCT, EVEN IF THE PARTY
HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Some states do not allow the
exclusion of incidental or consequential damages, so the above limitation or exclusion may not apply to
you. BY PURCHASING THIS PRODUCT, THE CONSUMER AGREES AND CONSENTS THAT ALL
DISPUTES BETWEEN THE CONSUMER AND DIRECTED SHALL BE RESOLVED IN
ACCORDANCE WITH CALIFORNIA LAWS IN SAN DIEGO COUNTY, CALIFORNIA.
declaration of conformity
manufacturer name:
manufacturer address:
Directed Electronics Inc.
One Viper Way
Vista, California 92081
declares, that the product:
product name:
C50ic
C60ic
C62ic
C80ic
conforms to the following standards:
EN55013
EN55020
7
© 2004 Directed Electronics, Inc. All rights reserved G39601.06.11.15 10-04
|