For Programming Assistance Please Call
Quick Start Guide
TOLL FREE 1-800 638-9228
Casio Model Numbers PCR-272, 140CR
Initialize Your Cash Register
1
(See Page 9 in the User’s Manual)
A) Insert the supplied key and
turn to the “OFF” position.
B) Plug the power cord into an AC outlet.
CAL X
Z
REG
PGM
OFF
RF
PGM
Load the Memory Protection Batteries and Paper Roll
2
(See Page 9 - 10 in the User’s Manual)
To prevent to lose all of your setting and sales data, we
recommended you to install the memory protection bat-
teries.
A) Remove the printer cover.
B) Open battery compart-
ment cover.
C) Insert 3 new “AA” type batteries
in to the compartment.
D) Turn to the “REG” position. Install the supplied 58mm paper roll
placing the paper roll into the printer well. Insert the paper into the
inlet and press
key to set the paper.
l
6
6
REGCAL X
OFF
Z
6
6
IMPORTANT Be sure that the plus (+) and minus (-) ends of the batteries
are facing in the directions indicated the illustration inside the
battery compartment.
RF
PGM
No battery is included in the accessories.
E) Proceed to the Next step “Setting the Date and Time”.
Setting the Date and Time
3
(See Page 11 in the User’s Manual)
B) When the display shows blinking
A) Using the key marked “PGM” turn
00-00-00
00-00-00
01-00-00
01-00-00
01-08-00
00-00
C) When the display shows blinking
the key to the “PGM” position.
00-00-00
“0”, such as
, enter
00-00
“0”, such as
, enter
CAL X
current date in Month, Day, Year
order.
Z
10-00
13-00
13-10
13-18
~00
REG
current time in Hour, Minute order.
PGM
OFF
Example: January, 8, 2010,
Example: 1:18 PM, enter
enter
.
?Z?<Z?
ZCZ<
RF
PGM
•
•
Enter 6-digit, last 2 digits for year set.
(2010 –>10)
key, this procedure
returns one by one.
• Enter 4-digit, use 24-hour system.
•
By pressing key, this procedure
y
By pressing
returns one by one.
y
01-08-10 • If you want to adjust the date/time,
please refer to page 31 of the User’s
Manual.
01-08-10
Setting Tax Rates
4
(See Page 11 in the User’s Manual)
Example1: Set state tax 6% to department 2, 3 key
Prepare the tax rate of your state. If your tax table has break point, refer to page 24 of the
user’s manual.
Start tax program
~
NS
ND
k
Enter tax rate and press dept key.
Enter tax rate and press dept key.
To end the setting.
Input the desired flat tax rate to the appropriate department key.
A) Turn the key to the “PGM” position.
CAL X
Z
REG
PGM
OFF
RF
Example 2: Set state tax 5.5% to department 2 key and tax
7% to department 3 key
PGM
Start tax program
~
B) Press the
key.
~
Enter tax rate and press dept key.
C) Enter tax rate.
B S
"B
Enter tax rate and press dept key.
To end the setting.
MD
k
(Example: For 6% enter “6”, 5.75% enter “5.75”.)
D) Press the appropriate department key.
E) Repeat step C) and D) to set other department key.
F) Press the
key to end tax programming.
s
Note: In case of setting the wrong tax rate to the key, please enter
and press those depart-
?
ment keys above, and quit this procedure by pressing
ning of this procedure.
key, and start from the begin-
k
Please start with the department 2 key (taxable department). Department 1 key is initial-
ized as non taxable.
Quick Start Setup Completed!
5
PleaseDkowenloeadpfrom Wtwhw.iSsomasnuhalse.coemt. Alfl Moanrualfs uSeatruch rAned Dorwenlofaed. rence.
QSG260*ES
0812-A
|