Models 370LM/370LMC
3-Button Security✚® Mini Remote Control
OWNER'S MANUAL
The 370LM/370LMC Series remote control (Security✚®)
works only with door openers and light controls having a
purple “learn” button and a yellow indicator light.
WARNING
To prevent possible SERIOUS INJURY or DEATH from a moving
gate or garage door:
Programming instructions are described and illustrated
below. The additional push buttons can also activate other
315MHz garage door openers and/or light controls.
(Instructions for programming light products are included
with those accessories.)
• ALWAYS keep remote controls out of reach of children. NEVER
permit children to operate, or play with remote control
transmitters.
• Activate gate or door ONLY when it can be seen clearly, is properly
adjusted, and there are no obstructions to door travel.
Instructions are Described and Illustrated Below
• ALWAYS keep gate or garage door in sight until completely closed.
NEVER permit anyone to cross path of moving gate or door.
9
1
9
1
7
3
7
5
5
KG
KG
Open/Close/Stop Operation
(Only if you have a Multifunction door control)
Your Security✚® remote control can be programmed to operate
one door using all 3 buttons: the left button will only open the
door, the middle button will only close the door, and the third
button will stop the door’s movement. You may set up this
feature as follows:
Open
Close
Stop
1. With the door closed, press and hold the
left remote push button.
1. Press and release the “learn” button on
the motor unit. The learn indicator light
will glow steadily for 30 seconds.
2. Press and hold the Lock button on the
door control.
3. Press and hold the door control push bar.
2. Within 30 seconds, press and hold the
button on the hand-held remote.
When the opener lights flash, release all buttons. Test by
pressing the left (Open) button on the remote. The door should
open. Press it again while the door is open and nothing should
happen. Press the middle (Close) button and the door should
close. Press the third (Stop) button while the door is moving
and it should stop immediately.
3. Release the button when the motor unit
light blinks. It has learned the code. If
light bulbs are not installed, two clicks
will be heard.
The Remote Control Batteries
To Erase All Codes From Motor Unit Memory
WARNING
To deactivate any unwanted remote, first erase all codes:
To prevent possible SERIOUS INJURY or DEATH:
Press and hold the “learn” button on motor unit until the learn
indicator light goes out (approximately
6 seconds). All previous codes are now
erased. Reprogram each remote or keyless
entry you wish to use.
• NEVER allow small children near batteries.
• If battery is swallowed, immediately notify doctor.
The lithium batteries should
produce power for up to
5 years. To replace, pry open
case as shown. Insert
To Control the Opener Lights
With SECURITY✚® transmitters, a remote push button can
be programmed to operate the opener lights without opening
the door.
batteries positive side up (+).
Dispose of old batteries
properly.
1. With the door closed, press and hold the remote button that
you want to control the light.
2. Press and hold the Light button on the door control.
3. Press and hold the Lock button on the door control.
4. After the opener lights flash, release all buttons.
NOTICE: To comply with FCC and or Industry Canada rules (IC), adjustment or modifications of
this receiver and/or transmitter are prohibited, except for changing the code setting or replacing
the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.
Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the fol-
lowing two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation.
Test by pressing the remote push button. The opener lights
should turn on or off but the door should not move.
© 2006, The Chamberlain Group, Inc.
All Rights Reserved
114A3091C
|