28-9-07
CR89
1950’S Stack-O-Matic Traveler
Instruction Manual
910-242700-0010-100
28-9-07
Turntable Operation
General
WARNING:
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE. DO NOT REMOVE COVER.
PILOT LAMPS SOLDERED IN PLACE. NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
Accessory: Adapter for 45 rpm
TROUBLESHOOTING
The unit will not operate.
To play a 45rpm record, place the adapter in the
center of the record. This unit includes six (6) adapters
found in the bag with the instruction manual.
1 Check that the unit is properly connected to an
A/C outlet.
2 Make certain that the small end of the adapter
is plugged in to the power inlet on the turntable.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
3 Check the ON/OFF VOLUME KNOB (10) to make
sure it is on.
The lighting flash with
arrowhead symbol, within
an equilateral triangle, is
intended to alert user to
the presence of uninsulated
"dangerous voltage" within
the product's enclosure
that may be of sufficient
magnitude to constitute
risk of electric shock
The exclamation point
within an equilateral
triangle is intended to
alert user to the
presence of important
operating and
maintenance (servicing)
instruction in the
literature accompanying
the appliance.
CAUTION: TO REDUCE
THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE
COVER (OR BACK). NO
USER - SERVICEABLE
PARTS INSIDE. REFER
SERVICING TO QUALIFIED
SERVICE PERSONNEL.
Adapter for 45 rpm
There is no sound
1 The volume has not been turned up.
Tone Control
Turntable is dragging
1 Make sure the Turntable Suspension Screws are
turned clockwise all the way in to allow the
turntable to sit on the suspension.
Use the Tone control to adjust the sound quality.
to persons.
CAUTION
For Compact Disc Units Only:
INVISBLE LASER RADIATION WHEN OPEN AND INTERLOCK FAILED
OR DEFEATED. AVOID DIRECT EXPORSURE TO LASER BEAM.
The Crosley Traveler Stack-O-Matic™ Record
Changer is equipped with a needle designed
specifically to fit Crosley Stack-O-Matic™ Record
Changers. Replacement needles (Model # NP1) are
available for purchase through Crosley Radio at
1-866-CROSLEY.
Specification
Power Supply
: AC adapter -(DC 12V 0.5A)(Included)
Power Consumption : 15W
Speed
Speaker
: 33 /45 /78 RPM
: 4” Dynamic Type x 2
Replacement Needle : NP1
* DESIGN AND SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE.
7
Turntable Operation
Welcome
Table of Contents
Thank you for purchasing the Crosley 1950’S Stack-
O-Matic Traveler (CR89). Before operating this unit,
please read this manual throughly and retain it for
future reference.
Getting Started
Turntable Features
to the “AUTO” position. The next record will drop
and begin to play.
Control Locators........................ 4
Unpacking................................ 5
Set Up...................................... 5
Power Source.......................... 5
1 Selectable 33/45/78 rpm speeds.
2 Load up to 6 records at a time.
3 Plays 7”, 10”, and 12” records.
11 To stop playback manually, move the TURNTABLE
SWITCH (8) to the “OFF” position. Gently lift
the TONE ARM (5) from the record and return
it to the TONE ARM REST (7).
About This Manual
12 To remove the records from the turntable, lift the
TENSION ARM (1) up and rotate it counter-
clockwise over the TONE ARM (5). Grab the
edges of the bottom record and lift straight up.
Instructions in the manual describe the controls and
functions of the CR89.
Turntable
Turntable Features.................... 6
Operating Instructions............... 6
4 Record changer is fully automatic or can be
operated manually.
5 Adjustable tone control.
Tone Arm Adjustment................ 6
Accessory: Adapter for 45 rpm
.................................................... 7
Tone Control............................... 7
Tone Arm Adjustment
Turntable Instructions
1 Turn power on by rotating the ON/OFF VOLUME
1
KNOB (10) clockwise.
2 Lift TENSION ARM (1) and rotate counter-clockwise
over the TONE ARM (5).
2
General
Troubleshooting Guide.............. 7
Warranty..................................... 8
3 Load desired records on the CENTER SPINDLE
(2). Records should be loaded one at a time.
4 Lift TENSION ARM (1) and rotate it clockwise over
the records and release. TENSION ARM (1) will
automatically pull down onto the records.
5 Set the SIZE SELECT SWITCH (6) to the correct
size of your records.
Do not turn
6 Set the SPEED SELECT SWITCH (4) to the correct
speed of your records.
7 Move the TURNTABLE SWITCH (8) to the “ON”
position. Turntable will begin to turn.
8. Remove white protective needle cover by gently
pulling towards the front of the unit.
3
1
Adjust this screw if the TONE ARM(25) is not
raising high enough to clear to the TONE ARM
REST(27). Turn the screw counter-clockwise
to raise the height. Turn the screw clockwise to
lower the height.
2
3
Adjust this screw if the TONE ARM(25) drops
on the record too early or too late. Turn the
screw counter-clockwise to start at a later point.
Turn the screw clockwise to start at an earlier
point.
9
Move the TURNTABLE SWITCH (8) to “AUTO”.
The switch will automatically return back to the
“ON” position and the first record will drop. The
TONE ARM (5) will automatically lift and move to
the beginning of the record. Once the first record
is finished, the TONE ARM (5) will move back to
the TONE ARM REST (7) and the next record
will drop. The TONE ARM (5) will move back to
the beginning of the record. This will repeat until
the last record is finished. When the last record
is finished, the TONE ARM (5) will return to its
rest and the turntable will shut off.
Adjust the screw if you feel there is not enough
tone arm pressure on the record. Turn the screw
counter-clockwise to increase pressure. Turn
the screw clockwise to descrease the pressure.
Note : Adjust the screws one turn at a time and check the
adjustment after each turn.
10 To manually switch to the next record during
playback, move the TURNTABLE SWITCH (8)
6
Getting Started
Getting Started
Unpacking
Control Locator
Set Up
12
3
2
1
1. TENSION ARM
2. CENTER SPINDLE
3. TURNTABLE
1 Remove packing materials from unit.
Note: Save all packing materials.
1 Plug A/C adapter into appropriate outlet.
4. SPEED SELECT SWITCH
5. TONE ARM
6. SIZE SELECT SWITCH
7. TONE ARM REST
8. TURNTABLE SWITCH
9. TONE CONTROL
10. ON/OFF VOLUME KNOB
11. AC ADAPTER
2 Remove plastic bag covering unit.
3 Remove tie from A/C adapter.
A/C adapter
5
6
Note: This product may be equipped with a
polarized alternating-current line plug (a
plug having one blade wider than the
other.) This plug will fit into the power
outlet only one way. This is a safety
feature. If you are unable to insert the
plug fully into the outlet try reversing the
plug, if the plug should still fail to fit, contact
your electrician to replace your obsolete
outlet. Do not defeat the safety purpose
of the polarized plug.
4 Open lid and remove styrofoam shipping
material from turntable.
7
8
5 Remove black tie-wrap from under the tone
arm.
(placed in a white cardboard box, located
at one side of poly-foam)
12. TURNTABLE SUSPENSION SCREW
6 Using your Fingers,Turn the Turntable
Suspension Screw (12) clockwise until it is all
the way down. Do not force it. This allows
turntable to float on its shock absorbers.
4
12
Power Source
Unwind the A/C power adapter (located in a
white box inside the packaging foam). Connect
the small end of the adapter to the back of the
turntable. Connect the other end to an A/C power
outlet.
9
10
7 Gently pull out the rubber shipping pads.
11
4
5
|