User’s Guide
BBG 6 A and BBG 6 A J
Blackburst / Color Bars / Audio Generator
Extron Electronics, USA
1230 South Lewis Street
Anaheim, CA 92805
800.633.9876 714.491.1500
FAX 714.491.1517
Extron Electronics, Europe
Beeldschermweg 6C
3821 AH Amersfoort, The Netherlands
+800.3987.6673 +31.33.453.4040
FAX +31.33.453.4050
Extron Electronics, Asia
135 Joo Seng Rd. #04-01
PM Industrial Bldg., Singapore 368363
+800.7339.8766 +65.6383.4400
FAX +65.6383.4664
Extron Electronics, Japan
Kyodo Building, 16 Ichibancho
Chiyoda-ku, Tokyo 102-0082
Japan
68-712-01 Rev. D
11 06
+81.3.3511.7655 FAX +81.3.3511.
© 2006 Extron Electronics. All rights reserved.
警告
安全须知 • 中文
电源 • 该 设 备 只 能 使 用 产 品 上 标 明 的 电 源 。 设 备
必 须 使 用 有 地 线 的 供 电 系 统 供 电 。 第 三 条 线
（ 地 线 ） 是 安 全 设 施 ， 不 能 不 用 或 跳 过 。
拔掉电源 • 为安全地从设备拔掉电源，请拔掉所有设备后
或桌面电源的电源线，或任何接到市电系统的电源线。
电源线保护 • 妥善布线， 避免被踩踏，或重物挤压。
这个符号提示用户该设备用户手册中
有重要的操作和维护说明。
这个符号警告用户该设备机壳内有暴
露的危险电压，有触电危险。
维护 • 所有维修必须由认证的维修人员进行。 设备内部没
有用户可以更换的零件。为避免出现触电危险不要自己
试图打开设备盖子维修该设备。
注意
阅读说明书 • 用 户 使 用 该 设 备 前 必 须 阅 读 并 理
解 所 有 安 全 和 使 用 说 明 。
通风孔 • 有些设备机壳上有通风槽或孔，它们是用来防止
机内敏感元件过热。 不要用任何东西挡住通风孔。
保存说明书 • 用户应保存安全说明书以备将来使
用。
锂电池 • 不正确的更换电池会有爆炸的危险。 必须使用与
厂家推荐的相同或相近型号的电池。 按照生产厂的建
议处理废弃电池。
遵守警告 • 用户应遵守产品和用户指南上的所有安
全和操作说明。
避免追加 • 不要使用该产品厂商没有推荐的工具或
追加设备，以避免危险。
Introduction
The BBG 6 A and BBG 6 A J (an exclusively Japanese model) are
compact, high performance blackburst, color bars, and audio
generators. Unless otherwise noted, the name BBG 6 A refers
to both the standard (USA and European countries) and the
Japanese models within this guide.
The BBG 6 A provides six broadcast quality blackburst signal
outputs on BNC connectors, two of which can be changed to
color bars with a DIP switch. For the standard BBG 6 A, the user
can select output signals as either NTSC or PAL.
The BBG 6 A J outputs NTSC only and has no setup pedestal in
its video output. Color bars are standard SMPTE bars (NTSC)
or full field (PAL). The audio generator provides a single 1
kHz sine wave audio tone, either balanced or unbalanced,
with a selectable output level of either +4 dBu (pro) or -10 dBV
(consumer).
The BBG 6 A is a member of the VersaTools® line of basic
distribution amplifiers, switchers, and video accessories. The
unit ships with an external, desktop 12 V power supply, which
accepts 100-240 VAC input.
Models
There are two available models of the BBG 6 A:
BBG 6 A (NTSC and PAL signal) — Handles NTSC and
PAL signals. This version is used in the USA and some other
countries.
BBG 6 A J (NTSC signal only) — Handles NTSC signals only.
This version is used in Japan.
Other than their differing signal options, these two models are
identical.
Installation
The BBG 6 A can be mounted on a rack shelf (VersaTools or
universal), under a desk or tabletop, or on a projector bracket.
Rack mounting
For optional rack mounting, mount the BBG 6 A on a VersaTools
19" 1U Rack Shelf (Extron part #60-190-20 or #60-604-20)
(figure 1) or a standard Universal 1U Rack Shelf (part #60-190-01
or 60-604-01) (figure 2). On the standard rack shelf, the BBG 6 A
mounts in one of four locations to the rear of the rack or in one
of four locations to the front of the rack.
BBG 6 A • Introduction
ꢀ
Installation
D
IS
T
R
IB
U
T
IO
D
IS
T
R
IB
U
T
IO
N
A
M
P
L
IF
IE
R
D
IS
T
R
IB
U
T
IO
N
A
M
P
L
IF
IE
R
D
IS
T
R
IB
U
T
IO
N
A
M
P
L
IF
IE
R
D
IS
T
R
IB
U
T
IO
N
A
M
P
L
IF
IE
M
D
A
VersaTools Rack Shelf
R
D
IS
T
S
N
R
IB
E
A
U
R
I
L
T
IO
E
IF
S
M
P
IE
R
1/4 Rack Width False
Front Face Plate
Figure 2 — Mounting the BBG 6 A on a standard
shelf
D
IS
T
R
IB
U
T
IO
N
A
M
P
L
IF
IE
R
(2) 4-40 x 3/16" Screws
Use 2 mounting holes
on opposite corners.
Furniture or projector mounting
Extron
BBG 6 A
Furniture mount or projector mount the unit using the optional
mounting kit (part #70-212-01 for furniture, or 70-217-04 for a
projector) as follows:
Black Burst
Color Bar
Audio Generator
1.
2.
3.
If rubber feet were previously installed on the bottom of
the unit, remove them.
Figure 1 — Rack mounting the BBG 6 A on a
VersaTools shelf
Attach the mounting brackets to the BBG 6 A with the
machine screws provided (figure 3).
1.
2.
If rubber feet were previously installed on the bottom of
the unit, remove them.
For furniture mounting, hold the unit with the attached
brackets against the underside of the table or other
furniture. Mark the location of the screw holes of the
bracket on the mounting surface.
Mount the unit on the rack shelf, using two 4-40 x 3/16"
screws in opposite (diagonal) corners to secure the
BBG 6 A to the shelf.
3.
Install blank panel(s) or other unit(s) to the rack shelf.
Projector
Mounting
Bracket
4.
Insert the shelf into the rack, aligning the holes in the shelf
with those of the rack.
Mounting
Bolt
5.
Secure the shelf to the rack using the supplied machine
screws. The VersaTools shelf can be mounted in the front
or in the rear of the rack.
0
.
1
2
V
A
M
PO
A
X
W
/
B
U
D
L
A
B
B
G
R
I
C
K
L
G
1
E
N
B
U
R
S
1
K
H
Z
6
A
1
0
d
E
R
B
V
R
+
4
d
A
U
A
T
/
T
O
C
P
A
1
2
3
B
u
D
R
O
I
O
L
O
N
R
B
A
R
C
O
B
L
A
L
O
C
K
B
U
R
S
R
B
A
R
T
/
1
4
1
3
B
L
A
C
K
B
U
R
S
T
Under-Desk
Mounting
6
5
Projector
Mounting
D
I
S
T
R
I
B
U
T
I
O
N
A
M
P
L
IF
I
E
R
Projector
Figure 3 — Desk and projector mounting the BBG 6 A
BBG 6 A • Installation
BBG 6 A • Installation
ꢁ
ꢂ
Installation
4.
For furniture mounting, drill 3/32" (2 mm) diameter pilot
holes, 1/4" (6.3 mm) deep in the mounting surface at the
marked screw locations.
DIP switch — Use these DIP switches to select between +4 dBu
(pro) or -10 dBV (consumer) audio output level, between NTSC
or PAL (USA only) output, and between blackburst or color bars
for outputs 1 and 2.
d
5.
For furniture mounting, insert #8 wood screws into the
four pilot holes. Tighten each screw into the mounting
surface until just less than 1/4" (6.3 mm) of the screw head
protrudes.
With the first DIP switch set to “+4,” the unit outputs
+4 dBu audio level with balanced wiring. With the DIP
switch set to “-10,” the unit outputs -10 dBV audio level
with unbalanced wiring.
N
6.
7.
8.
For furniture mounting, align the mounting screws with
the slots in the brackets and place the unit against the
surface, with the screws through the bracket slots.
NTSC
+4
RESERVED
Blackburst
Blackburst
+4
For furniture mounting, slide the unit slightly forward
or back, then tighten all four screws to secure the unit in
place.
ON
ON
1
2
3
1
2
3
For projector mounting, secure the unit to a projector
mount or other surface by inserting the mounting bolt
through the bracket’s slotted hole.
-10
Color bars
-10
Color bars
PAL
BBG 6 A
BBG 6 A J
Figure 5 — BBG 6 A and BBG 6 A J DIP switches
Connections, Indicators, and Controls
DIP switch 2 of the BBG A J is not used.
N
See figure 4 below.
Please refer to the table below for other combinations.
N
Power/Signal indicator LED — When illuminated, this LED
indicates that the BBG 6 A is receiving power.
a
Output
Dip
Switch
Balanced Unbalanced
Position
Blackburst only outputs — Connect up to four display devices
to these BNC connectors for blackburst output.
b
+4
+4 dBu
-4 dBV
-2 dBu
Blackburst/color bars outputs — Connect up to two display
devices to these BNC connectors for blackburst or color bars
output.
c
-10
-10 dBV
1
BLACKBURST
BBG 6 A
7
BLACKBURST AND AUDIO
GENERATOR
1
2
3
4
5
6
POWER
12V
.2A MAX
1 KHZ
AUDIO
L
R
ON
1
2
3
COLORBARS
6
4
2
5
3
Figure 4 — BBG 6 A front and rear panels
BBG 6 A • Installation
BBG 6 A • Connections, Indicators, and Controls
ꢃ
ꢄ
Connections, Indicators, and Controls
To verify the polarity before connection, plug in the power
supply with no load and check the output with a voltmeter.
Audio output connector — Insert a 3.5 mm, 5-pole captive
screw connector into this connector for a balanced or
unbalanced 1 kHz sine wave audio tone.
e
As an alternative, you can use an Extron P/S 100 Universal
12 VDC Power Supply (part #60-357-01), which can power up to
ten BBG 6 As or other Extron 12 VDC devices using only one AC
power connector.
Do not tin the stripped power supply leads before
installing the captive screw connector. Tinned wires are
not as secure in the captive screw connectors and could
pull out.
N
Version label — Differentiates the standard (NTSC and PAL
signals) versus Japanese (BBG 6 A J, NTSC signals only) versions
of the BBG 6 A.
g
CAUTION
For unbalanced audio, connect the sleeve(s) to the ground contact.
DO NOT connect the sleeve(s) to the negative (-) contacts.
Specifications
3/16" (5 mm) MAX.
Tip
Ring
Sleeve (s)
Tip
Tip
NO Ground Here
Sleeve (s)
Blackburst output
Number/signal type..................... 6 blackburst (two can be switched to
color bars)
Tip
NO Ground Here
Ring
Balanced Output
Unbalanced Output
Connectors ..................................... 6 BNC female
Standards
Figure 6 — BBG 6 audio wiring
Power connector — Plug the external 12 V power supply
into this 2-pole captive screw connector. The power supply
is included with the unit. Figure 7 shows how to wire the
connector.
BBG 6 A............................... RS-170A standard for NTSC 3.58,
CCIR 624-4 standard for PAL
BBG 6 A J............................. RS-170A standard for NTSC 3.58
Impedance ..................................... 75 ohms
Sync level
BBG 6 A............................... 40 IRE for NTSC, 43 IRE for PAL
BBG 6 A J............................. 40 IRE for NTSC
Color burst level
BBG 6 A............................... 40 IRE for NTSC, 43 IRE for PAL
BBG 6 A J............................. 40 IRE for NTSC
Setup level
f
When connecting the power supply, voltage polarity
is extremely important. Applying power with
incorrect voltage polarity could damage the power
supply and the BBG 6 A. Identify the power cord
negative lead by the ridges on the side of the cord or
the black heat shrink wrapping around it.
C
BBG 6 A............................... 7.5 IRE (NTSC) or 0 IRE (PAL)
BBG 6 A J............................. 0 IRE (NTSC)
Tolerance for all levels.................. 3%
Subcarrier levels
A
A
3/16” (5 mm) MAX.
+
-
+
-
12 V
SECTION A–A
Power Supply
Output Cord
Captive Screw
Connector
BBG 6 A............................... NTSC 3.579545 3 Hz
PAL 4.433618 3 Hz
BBG 6 A J............................. NTSC 3.579545 3 Hz
Figure 7 — Power connector wiring
Do not tin the stripped power supply leads before
N
installing the captive screw connector. Tinned wires are
not as secure in the captive screw connectors and could
pull out.
The two power cord wires must be kept separate
while the power supply is plugged in. Remove
power before continuing.
W
BBG 6 A • Connections, Indicators, and Controls
BBG 6 A • Specifications, Parts, and Accessories
ꢅ
ꢆ
Specifications, Part Numbers, and Accessories
Color Bars output
Number/signal type
General
External power supply................. 100 VAC to 240 VAC, 50/60 Hz, 2.5 watts,
external, autoswitchable; to 12 VDC,
BBG 6 A............................... 2 color bars, switchable, standard
SMPTE bars for NTSC,
1 A, regulated power supply
full field 8-bar for PAL
Power input requirements........... 12 VDC, 0.2 A (max.)
BBG 6 A J............................. Standard SMPTE bars for NTSC
Connectors ..................................... 2 BNC female
Standards
BBG 6 A............................... NTSC 3.58, PAL
BBG 6 A J............................. NTSC 3.58
Impedance ..................................... 75 ohms
Sync level
BBG 6 A............................... 40 IRE for NTSC, 43 IRE for PAL
BBG 6 A J............................. 40 IRE for NTSC
Color burst level
BBG 6 A............................... 40 IRE for NTSC, 43 IRE for PAL
BBG 6 A J............................. 40 IRE for NTSC
Setup level
Temperature/humidity................ Storage: -40 to +158 °F (-40 t +70 °C) /
10% to 90%, noncondensing
Operating: +32 to +122 °F (0° to +50 °C) /
10% to 90%, noncondensing
Rack mount.................................... Yes, with optional 1U VersaTools® 3" deep
rack shelf, part #60-190-20 (RSF 123) or
60-604-20 (RSB 123); or Universal 9.5"
deep rack shelf, part #60-190-01 (RSU 129)
or 60-604-01 (RSB 129). Also under-desk
mountable with optional MBU 123 kit
part #70-212-01.
Enclosure type .............................. Metal
Enclosure dimensions .................. 1.7" H x 4.3" W x 3.0" D
(1U high, quarter rack wide)
4.3 cm H x 10.9 cm W x 7.6 cm D
(Depth excludes connectors.)
Product weight .............................. 0.4 lbs (0.2 kg)
Shipping weight ........................... 3 lbs (2 kg)
Vibration ........................................ ISTA 1A in carton
(International Safe Transit Association)
BBG 6 A............................... NTSC, 7.5 IRE; PAL, 0 IRE
BBG 6 A J............................. NTSC, 0 IRE
White level ..................................... 100 IRE
Tolerance for all levels.................. 3%
Subcarrier levels
BBG 6 A............................... NTSC 3.579545 3 Hz, PAL 4.433618 3 Hz
BBG 6 A J............................. NTSC 3.579545 3 Hz, no setup pedestal
Listings............................................ UL, CUL
Compliances................................... CE, FCC Class A, VCCI, AS/NZS, ICES
MTBF............................................... 30,000 hours
Audio output
Number/signal type..................... 1 set (L and R) of stereo sine waves,
balanced or unbalanced
Connectors .................................... (1) 3.5 mm captive screw connector, 5 pole
Impedance ..................................... 50 ohms unbalanced, 100 ohms balanced
Warranty ........................................ 3 years parts and labor
All nominal levels are at 10%.
N
N
Specifications are subject to change without notice.
Signal level..................................... Selectable: professional level, +4 dBu
(1.23 V) balanced; or consumer level,
-10 dBV (316 mV) unbalanced
THD................................................. 0.1%
Tolerance for all levels.................. 3%
Signal frequency ........................... 1 kHz
0 dBu = 0.775 V, 0 dBV = 1 V, 0 dBV 2 dBu.
N
BBG 6 A • Specifications, Parts, and Accessories
BBG 6 A • Specifications, Parts, and Accessories
ꢇ
ꢈ
|