®
POWERSHRED 53C
Please read these instructions before use.
Do not discard: keep for future reference.
Quality Office Products Since 1917
BASIC SHREDDING OPERATION
PAPER OR CD/CARD
2
3
4
5
1
or
Continuous operation:
Up to 3 minute maximum
Plug in and put
Set to Auto-On (I)
Feed into card/CD entry
and release
When finished shredding
set to OFF (O)
Feed paper straight
into paper entry
and release
NOTE: Shredder runs briefly after each
pass to clear entry. Continuous operation
beyond 3 minutes will trigger a 30-minute
cool down period.
disconnect power
switch in ON (I) position
TROUBLESHOOTING
PAPER JAM
Shredder doesn’t start:
1
2
6
4
5
3
Make sure head is on basket correctly
Wait 30 minutes for motor to cool down
Remove and empty basket
Set to Reverse (R)
for 2-3 seconds
Alternate slowly back and forth
Set to Off (O)
and unplug
Gently pull uncut
paper from paper
entry. Plug in.
Set to Auto-On
(I) and resume
shredding
PRODUCT MAINTENANCE
OILING SHREDDER
CLEANING AUTO-START INFRARED SENSORS
All cross-cut shredders require oil for peak performance. If not oiled, a
Paper detection sensors are designed for maintenance free operation. However, on rare occasions, the
sensors may become blocked by paper dust causing the motor to run even if there is no paper present.
(Note: two paper detection sensors are located in the center of the paper entry).
machine may experience diminished sheet capacity, intrusive noise when
shredding, and could ultimately stop running. To avoid these problems, we
recommend you oil your shredder each time you empty your waste bin.
FOLLOW OILING PROCEDURE BELOW AND REPEAT TWICE
TO CLEAN THE SENSORS
3
1
2
3
1
2
4
Turn off and unplug
shredder
Locate Auto-start
infrared sensor
Dip cotton swab in
rubbing alcohol
Using cotton swab, wipe
away any contamination
from the paper sensors
Set to Reverse (R)
2-3 seconds
Set to Off (O)
*Apply oil
across entry
*Only use a non-aerosol vegetable oil in long
nozzle container such as Fellowes 35250
LIMITED PRODUCT WARRANTY
Limited Warranty: Fellowes, Inc. (“Fellowes”) warrants the parts of the machine to be free of additional costs incurred by Fellowes to provide parts or services outside of the country where the
defects in material and workmanship and provides service and support for 2 years from the date shredder is initially sold by an authorized reseller. ANY IMPLIED WARRANTY, INCLUDING THAT OF
of purchase by the original consumer. Fellowes warrants the cutting blades of the machine to MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, IS HEREBY LIMITED IN DURATION
be free from defects in material and workmanship for 5 years from the date of purchase by the TO THE APPROPRIATE WARRANTY PERIOD SET FORTH ABOVE. In no event shall Fellowes be liable
original consumer. If any part is found to be defective during the warranty period, your sole and for any consequential or incidental damages attributable to this product. This warranty gives you
exclusive remedy will be repair or replacement, at Fellowes’ option and expense, of the defective specific legal rights. The duration, terms, and conditions of this warranty are valid worldwide,
part. This warranty does not apply in cases of abuse, mishandling, failure to comply with product except where different limitations, restrictions, or conditions may be required by local law. For
usage standards, shredder operation using an improper power supply (other than listed on more details or to obtain service under this warranty, please contact us or your dealer.
label), or unauthorized repair. Fellowes reserves the right to charge the consumers for any
Australia Residents Only:
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other
reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.
The benefits under Fellowes’ Warranty are in addition to other rights and remedies under a law in relation to the shredder.
®
POWERSHRED 53C
Declaration of Conformity
Fellowes Manufacturing Company
Yorkshire Way, West Moor Park, Doncaster, South Yorkshire, DN3 3FB, England declares that the product Model 53C conforms with the requirements of the Restriction of Hazardous Substances
Directive (2011/65/EU), the Low Voltage Directive (2006/95/EC), the Electromagnetic Compatibility Directive (2004/108/EC), the WEEE directive (2002/96/EC), and below harmonized European
EN Standards.
Safety: EN 60950-1
EMC Standard: EN55014-1
Year Affixed: 12
EN55014-2
EN61000-3-2
EN61000-3-3
Itasca, Illinois, USA
January 1, 2013
James Fellowes
W.E.E.E.
This product is classified as Electrical and Electronic Equipment. Should the time come for you to dispose of this product please ensure that you do so in accordance with the European Waste of Electrical
and Electronic Equipment (WEEE) Directive and in compliance with local laws relating to this directive.
For more information on the WEEE Directive please visit www.fellowesinternational.com/WEEE
Questions or Concerns?
Customer Service & Support
Troubleshooting
Troubleshooting
Registration
Replacement parts
General questions
Manuals
Australia
Europe
+61-1-800-33-11-77
00800-1810-1810
+44-(0)-1302-836800
+1-800-955-0959
United Kingdom
United States
©2013 Fellowes, Inc. Part No. 407046 Rev C
|