BatteryChargers
AA RECHARGER
POWERCHARGER
Quick Start Guide
Model # PP2020/PP2010
04-13
HOW THE BATTERYCHARGERS WORK
The PowerCharger (PP2020) with internal power source (Lith-Ion battery) and
the AA Recharger (PP2010) with removable power source (AA NiMh batteries)
store electrical energy, so it can be used to recharge your portable electronic
devices whenever you’re away from your home or campsite. Press the orange
lid latch button on the side of the battery charger to access the Input and
Output ports as shown below.
OUTPUT-Used for charging your device(s)
from the BatteryCharger’s internal battery
(once charged via AC wall charger)
INPUT-Used for charging the BatteryCharger’s
internal battery from wall charger.
FROM WALL CHARGER
USB PORT
FROM BatteryCharger
(standard USB plug)
OUTPUT PORT
(standard USB plug)
TO BatteryCharger
INPUT PORT
TO PORTABLE DEVICE
(micro USB plug)
CHARGING PORT*
(micro USB plug)
OUTPUTS
* Use USB charging cable included with your
device if this connector is not compatible.
PP2020
PP2010
Field Light INPUT
OUTPUT
Lid Latch
Button
INPUT
Field Light
2
CHARGING THE BATTERYCHARGER FROM THE WALL CHARGER
1. (Model PP2010 only) Press the front battery pod grip (A) in until it clicks,
then pull the battery pod (B) out of the bottom of the battery charger.
Insert the 4 supplied AA NiMh rechargeable batteries if they are not
already in place.
2.
3.
Press the lid latch button and pull open the top of the BatteryCharger.
Connect the USB cable to the micro-USB INPUT port from the USB port
on the supplied AC charger (see packing list), and plug it into a wall outlet
(100-240v).
4.
Press the Power button at the center of the PowerSync Power Gauge (C).
All four LEDs on the Power Gauge (Fig. 1) will light up (for 10 min.) when
the BatteryCharger’s internal battery has been fully charged (you may
leave it connected to the charger overnight without risk of overcharging),
and you’re ready to connect and charge your device.
CHARGING YOUR DEVICE FROM THE BATTERYCHARGER
Press the power button at the center of the PowerSync Power Gauge (C)
to check the BatteryCharger’s charge status, then connect the supplied
USB cable from the OUTPUT port of the BatteryCharger to your device to
recharge it. If your device uses a non-standard type of connector, use the
cable that came with it to connect to the BatteryCharger’s OUTPUT port.
Check the charge indicator on your device to determine when it’s ready
to use. The NiMh AA batteries inside the PP2010 may also be removed and
used to power any device that operates on AA batteries (unless the use of
rechargeable batteries is not recommended).
STORING & TRANSPORTING THE BATTERYCHARGER
Close the top lid when storing or transporting the BatteryCharger, to help
keep dirt and debris out of the USB ports.
PowerSync
Power Gauge
C
NiMh AA Battery Pod
B
(PP2010 only)
Power
Button
Battery Pod Grip
A
WARNING: INSERT ONLY NiMh AA
BATTERIES IN THE PP2010. NEVER
ATTEMPT TO CHARGE ALKALINES
OR LITHIUMS.
(front side)
(PP2010 only)
3
UNDERSTANDING THE POWERSYNC POWER GAUGE
The 4 LED charge indicators behind the Power Gauge (C) allow you to monitor
the status of the BatteryCharger’s internal battery. While the battery is
charging from the AC wall charger, the LEDs will light up in sequence to show
the charge level as shown in Fig. 1. The LED indicating the current battery
level will blink rapidly while charging. When charging is complete, all LEDs
remain on for 10 min., then shut off until the Power button is pressed.
Blinking
Fig. 1
Charging In
from AC
>25%
>50%
>75%
>90%
FULL
While the BatteryCharger is charging your connected device (Power button
must be pressed), the LEDs will monitor the BatteryCharger’s battery level as
shown in Fig. 2, with a single LED blinking once every 15 sec. (shows active
charging but conserves battery power).
Slowly Blinking
Fig. 2
Charging Out
to Device
<25%
<50%
<75%
<90%
FULL
You can also check the current level of the BatteryCharger’s battery charge
anytime by pressing the Power button, even when it is not connected to the
charger or an external device. The LEDs will glow steadily to indicate the
charge level % as shown in Fig.3. , then shut off after 10 seconds.
Blinking
Fig. 3
Checking
Charge Level
<25%
>25%
>50%
>75%
FULL
The Field Light will glow during charging. You can also press
the power button at any time to turn it on to help insert the
USB cable into the Output port when you’re charging at night.
Field Light
4
TECHNICAL SPECIFICATIONS
Model
Weight
Size
PP2020 PowerCharger
PP2010 AA Recharger
9.3 oz / 167 g
7.9 oz / 153 g
5.0 x 3.1 x 0.9 in.
approx. 5 hrs.
5.9 x 3.3 x 1.1 in.
approx. 8 hrs.
Charge Time (Wall
Charger)
Power Output
5 volts, 1 amp (1000 mA)
High Capacity Lith Ion (20 Whr)
n/a
5 volts, 1 amp (1000 mA)
n/a
Internal Battery Type
Removable Batteries
(included)
4x NiMh rechargeable AA (2000ma)
USB Inputs / Outputs
Operating Temp. Range
Storage Temp. Range
1 / 2*
1 / 1
-4 ~ 112o F (-20~44o C)
-4 ~ 140o F (-20~60o C)
-4 ~ 112o F (-20~44o C)
-4 ~ 140o F (-20~60o C)
Recommended
Cell Phones (inc Smartphones)/3x,
MP3 Players/4x, Digital Cameras/7x,
Tablet/1x Note: Tablets and other
Cell Phones (inc Smartphones)/1x, MP3
Players/2x, Digital Cameras/2.5x
Note: Tablets and other devices have
Devices/# of Charges**
(from fully charged
internal battery)
devices have higher power requirements higher power requirements and may
and may not attain a full charge from
the BatteryCharger battery.
not attain a full charge from the
BatteryCharger battery.
* Two devices may be charged simultaneously. They will not charge any slower than if only one device was connected,
however the PowerCharger’s internal battery charge will be depleted more rapidly.
** Rechargeable batteries in electronic devices charge at different rates, depending on many factors including temperature, age and circuit
design. Bushnell provides examples of charges per device, based on typical product use and are not intended to be specific to any single device.
After pressing orange lid latch button,
carabiner clip can be opened for easy
attachment to backpacks, belt loops, etc.
Press clip back into place and secure latch
before transporting.
WARNING: MODEL PP2010 IS DESIGNED TO RECHARGE ONLY NiMh (Nickel Metal
Hydride) AA RECHARGEABLE BATTERIES. USE ONLY THE SUPPLIED NiMh BATTERIES
OR COMPARABLE REPLACEMENTS. NEVER ATTEMPT TO CHARGE ALKALINE OR
LITHIUM AA BATTERIES IN THE PP2010.
5
ONE YEAR LIMITED WARRANTY
Your Bushnell® POWERSYNC product is warranted to be free of defects in materials and workmanship for one year after the date of purchase.
In the event of a defect under this warranty, we will, at our option, repair or replace the product, provided that you return the product
postage prepaid. This warranty does not cover damages caused by misuse, improper handling, installation, or maintenance provided by
someone other than a Bushnell Authorized Service Department.
Any return made under this warranty must be accompanied by the items listed below:
1.
2.
3.
4.
5.
A check/money order in the amount of $10.00 to cover the cost of postage and handling
Name and address for product return
An explanation of the defect
Proof of Date Purchased
Product should be well packed in a sturdy outside shipping carton, to prevent damage in transit, with return postage prepaid
to the address listed below:
IN U.S.A. Send To:
Bushnell Outdoor Products
Attn.: Repairs
IN CANADA Send To:
Bushnell Outdoor Products
Attn.: Repairs
9200 Cody
Overland Park, Kansas 66214
25A East Pearce Street, Unit 1
Richmond Hill, Ontario L4B 2M9
For products purchased outside the United States or Canada please contact your local dealer for applicable warranty information. In
Europe you may also contact Bushnell at:
Bushnell Germany GmbH
European Service Centre
Mathias-Brüggen-Str. 80
D-50827 Köln
GERMANY
Tél: +49 221 995568-0
Fax: +49 221 995568-20
This warranty gives you specific legal rights.
You may have other rights which vary from country to country.
©2013 Bushnell Outdoor Products
FCC Compliance Statement
This device complies with Part 15 of the FCC interference limits for Class B digital devices FOR HOME OR OFFICE USE. These limits are
designed to provide reasonable protection against harmful interference in a residential installation, and are more stringent than“outdoor”
requirements.
Operation of this device is subject to the following conditions; (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
The device does not contain any user-serviceable parts. Repairs should only be made by an Authorized Bushnell repair center. Unauthorized
repairs or modifications could result in permanent damage to the equipment, and will void your warranty and your authority to operate
this device under Part 15 regulations.
The shielded interface cable which is provided must be used with the equipment in order to comply with the limits for a digital device
pursuant to Subpart B of Part 15 of FCC Rules.
Specifications and designs are subject to change without
any notice or obligation on the part of the manufacturer.
|