Wheel Dolly StanD/holDer
Model 95409
aSSeMbly anD operation inStructionS
Wheel dollies (sku 94682) sold separately.
Due to continuing improvements, actual product may differ slightly from the product described herein.
®
349ꢀ Mission Oaks Blvd., Camarillo, CA 930ꢀꢀ
to preVent SeriouS injury, reaD anD unDerStanD
all WarningS anD inStructionS beFore uSe.
Copyright© 2006 by Harbor Freight Tools®. All rights reserved. No portion of
this manual or any artwork contained herein may be reproduced in any shape
or form without the express written consent of Harbor Freight Tools.
For technical questions or replacement parts, please call 1-800-444-3353.
SKU 95409
For technical questions, please call 1-800-444-3353.
Page ꢀ
could briefly create an excess load which may result in damage to the tool or
personal injury.
8.
only use on a flat, level and stable surface able to withstand the weight of
the Wheel Dolly Stand/holder and it maximum weight capacity of 300 lb.
9.
use this tool correctly. Do not at any time use this tool for transporting people
or animals.
ꢀ0.
Do not use the Wheel Dolly Stand/holder if it is damaged or broken. All
repairs should only be completed by a qualified repair facility.
note: The warnings, cautions, and instructions discussed in this instruction manual
cannot cover all possible conditions and situations that may occur. It must be
understood by the operator that common sense and caution are factors that
cannot be built into this product but must be supplied by the operator.
unpacKing
When unpacking, check to be sure that all parts listed on page 5 of this manual
are included. If any parts are missing or broken, please call Harbor Freight Tools at
ꢀ-800-444-3353 as soon as possible.
SKU 95409
For technical questions, please call 1-800-444-3353.
Page 3
aSSeMbly
Figure 1
ꢀ.
2.
Attach Caster Assembly (ꢀ) to Left Main Beam (2) using Flat Washer (3), Lock
Washer (4) and Nut (5). See Figure ꢀ.
Follow the same procedure with the remaining three Caster Assemblies (ꢀ) and
the Right Main Beam (8).
Figure 2
3.
Attach Cross Beam (7) to Right Main Beam (8) and Left Main Beam (2) using
Bolt (6), Flat Washer (3), Lock Washer (4) and Nut (5). See Figure 2.
SKU 95409
For technical questions, please call 1-800-444-3353.
Page 4
operation
ꢀ.
2.
Place one Wheel Dolly (sku 94682, sold separately) on each of the four hold-
ers on the Cross Beam (7). The metal part of each dolly should slide over one
holder.
Store stand and dollies in a dry, level place where they will not present a tripping
hazard.
partS liSt
part
Description
Q’ty
part
Description
Q’ty
ꢀ
2
3
4
Caster Assembly
4
ꢀ
8
8
5
6
7
8
Nut Mꢀ2
8
4
ꢀ
ꢀ
Left Main Beam
Flat Washer Mꢀ2
Lock Washer Mꢀ2
Bolt Mꢀ2 X 30 (ꢀ-ꢀ/4” long)
Cross Beam
Right Main Beam
pleaSe reaD the FolloWing careFully
THe MANUFACTUReR AND/OR DISTRIBUTOR HAS PROvIDeD THe PARTS LIST AND
ASSeMBLY DIAGRAM IN THIS MANUAL AS A ReFeReNCe TOOL ONLY. NeITHeR THe
MANUFACTUReR OR DISTRIBUTOR MAKeS ANY RePReSeNTATION OR WARRANTY OF
ANY KIND TO THe BUYeR THAT He OR SHe IS qUALIFIeD TO MAKe ANY RePAIRS TO THe
PRODUCT, OR THAT He OR SHe IS qUALIFIeD TO RePLACe ANY PARTS OF THe PROD-
UCT. IN FACT, THe MANUFACTUReR AND/OR DISTRIBUTOR eXPReSSLY STATeS THAT
ALL RePAIRS AND PARTS RePLACeMeNTS SHOULD Be UNDeRTAKeN BY CeRTIFIeD AND
LICeNSeD TeCHNICIANS, AND NOT BY THe BUYeR. THe BUYeR ASSUMeS ALL RISK
AND LIABILITY ARISING OUT OF HIS OR HeR RePAIRS TO THe ORIGINAL PRODUCT OR
RePLACeMeNT PARTS THeReTO, OR ARISING OUT OF HIS OR HeR INSTALLATION OF
RePLACeMeNT PARTS THeReTO.
SKU 95409
For technical questions, please call 1-800-444-3353.
Page 5
aSSeMbly DiagraM
record product’s Serial number here:
note: If product has no serial number, record month and year of purchase instead.
note: Some parts are listed and shown for illustration purposes only, and are not avail-
able individually as replacement parts.
SKU 95409
For technical questions, please call 1-800-444-3353.
Page 6
|