Instruction booklet
DISHWASHER
Contents
EN
Installation,
Positioning and levelling
2-3-4
English, 1
Connecting the water and electricity supplies
Technical data
Electrical Connection
Description of the appliance, 5
Overall view
Control panel
Display
Loading the racks, 6
Lower rack
Cutlery basket
Upper rack
Start-up and use,
Starting the dishwasher
Loading the detergent
Washing options
7
IDE 750
Wash cycles, 8
Wash cycle table
Rinse aid and refined salt,
Loading the rinse aid
9
Loading the refined salt
Care and maintenance, 10
Shutting off the water and electricity supplies
Cleaning the dishwasher
Preventing unpleasant odours
Cleaning the sprayer arms
Cleaning the filters
Leaving the machine unused for extended periods
Precautions and advice, 11
General safety
Disposal
Saving energy and respecting the environment
Troubleshooting, 12
Connecting the water outlet hose
Advice regarding the first wash cycle
EN
Connect the outlet hose (without bending it) to a
drain duct with a minimum diameter of 4 cm.
Alternatively, rest it over a sink or tub; the free end
of the hose should not remain immersed in water.
After the appliance has been installed, immediately
before running the first wash cycle, completely fill
the salt dispenser with water and add approximately
2 kg of salt (see Rinse aid and refined salt). The
water may overflow: this is normal and is not a
cause for concern. It is also normal that the LOW
SALT* indicator light continues to flash for a few
cycles after the salt has been loaded.
The special plastic
A
elbow* makes it easier to
find the best layout: fix
the elbow to the wall
securely in order to
prevent the outlet hose
from moving and spilling
the dirty water.
The part of the hose
marked with the letter A
should be between 40 and 100 cm above the ground
(see figure).
Technical data
width 60 cm
height 85 cm
depth 60 cm
We advise against the use of hose extensions.
Dimensions
Capacity
Electrical connection
12 standard place-settings
Before inserting the plug into the electrical socket,
make sure that:
0,03 ÷ 1MPa (0.3 ÷ 10 bar)
4.3 psi – 145 psi
Water supply
pressure
Power supply
voltage
See appliance data plate
See appliance data plate
See appliance data plate
•
•
the socket is earthed and complies with current
regulations;
Total absorbed
power
the socket can withstand the maximum load of
the appliance, which is indicated on the data
plate located on the inside of the door (see
Description of the appliance);
Fuse
This dishwasher conforms to
the following European
Community Directives:
-73/23/EEC dated 19/02/73
(Low Voltage) and subsequent
modifications
-89/336/EEC dated 03/05/89
(Electromagnetic Compatibility)
and subsequent modifications
-97/17/EC (Labelling)
•
•
the power supply voltage falls within the values
indicated on the data plate on the inside of the
door;
the socket is compatible with the plug of the
appliance. If this is not the case, ask an
authorised technician to replace the plug (see
Assistance); do not use extension cables or
multiple sockets.
-2002/96/ CE Waste Electrical
and Electronic Equipment
(WEEE)
Once the appliance has been installed, the
power supply cable and the electrical socket should
be easily accessible.
The cable should not be bent or compressed.
If the power supply cable is damaged, it must
be replaced by the manufacturer or its Technical
Assistance Service in order to prevent all potential
hazards. (See Assistance)
The Company shall not be held responsible for
any incidents that occur if these regulations are not
observed.
* Only available in selected models.
3
Electrical Connection
Electrical Connection
As the colours of the wires in the mains lead may not
EN
If your appliance is supplied with a 13 amp. fused
plug it can be plugged into a 13 amp socket for
immediate use. Before using the appliance please
read the instruction below.
correspond with the coloured markings identifying the
terminal in your plug, proceed as follows:
connect Green & Yellow wire to terminal market “E” or
coloured Green or Green & Yellow.
Connect Brown wire to terminal marked “L” or
coloured Red.
Connect Blue wire to terminal marked “N” or coloured
Black.
WARNING: THIS APPLIANCE MUST BE
EARTHED.
THE FOLLOWING OPERATIONS SHOULD BE
CARRIED OUT BY A QUALIFIED ELECTRICIAN.
If a 13 amp plug (BS 1363) is used it must be fitted
with a 13 amp fuse. A15 amp plug must be protected
by a 15 amp fuse, either in the plug or adaptor or at
the distribution board.
If you are in any doubt about the electrical supply to
your machine, consult a qualified electrician before
use.
Replacing the fuse:
When replacing a faulty fuse, a 13 amp ASTA
approved fuse to BS 1362 should always be used,
and the fuse cover re-fitted. If the fuse cover is lost,
the plug must not be used until a replacement is
obtained.
Replacemente fuse covers:
If a replacement fuse cover is fitted, it must be of
the correct colours as indicated by the coloured
marking or the colour that is embossed in words on
the base of the plug. Replacements can be obtained
directly from your nearest Service Depot.
How to connect an alternative plug:
The wires in this mains lead are coloured in
accordance with the following code:
BLUE
“NEUTRAL” (“N”)
“LIVE” (“L”)
Removing the plug:
BROWN
Ifyour appliance has a non-rewireable moulded plug
and you should wish to remove it to re-route the
mains cable through partitions, units etc., please
esure that either:
GREEN AND YELLOW
“EARTH” (“E”)
GREEN &
YELLOW
- the plug is replaced by a fused 13 amp re-wireable
plug
- or:
bearing the BSI mark of approval
13 amp fuse
BROWN
BLUE
- the mains cable is wired directly into a 13 amp
cable outlet, controlled by a switch, (in compliance
CROSS-BAR
CORD GRIP
with BS 5733) which
is accessible without
moving the appliance.
Disposing of the plug:
Ensure that before disposing of the plug itself, you
make the pins unusable so that it cannot be
accidentally inserted into a socket.
Instruction for connecting cable to an altenative
plug:
Important: the wires in the mains lead are coloured
in accordance with the following code:
Disposing of the appliance:
When disposing of the appliance please remove the
plug by cutting the mains cable as close as possible
to the plug body and dispose of it as described
above
Green & Yellow
Blue
Brown
- Earth
- Neutral
- Live
CAUTION:
- Once the appliance has been installed, the electrical
plug and socket should remain accessible.
- The Company shall not be held responsible for any
incidents that occur if these regulations are not
observed.
4
Description of the appliance
Overall view
EN
1.
Upper rack
2.
Upper sprayer arm
Tip-up compartments
Rack height adjuster
Lower rack
3.
4.
5.
1
4
6.
Lower sprayer arm
Cutlery basket
Washing filter
3
2
7.
8.
9.
Salt dispenser
10.
11.
Detergent and rinse aid dispensers
Data plate
5
6
7
9
8
10
11
ON-OFF
button
Control panel
DISPLAY
START/RESET
button
WASH CYCLE
SELECT
Knob
DELAYED START
button*
EXTRA DRYING
button*
HALF LOAD
button*
Display
LOW RINSE AID
indicator light*
PRE-WASH
WASH
RINSE
LOW SALT
indicator light*
WASH
CYCLE PHASE
indicator lights
DRYING
DELAYED
START
indicator light*
EXTRA DRYING
indicator light*
HALF LOAD
indicator light*
* Only available in selected models.
5
Loading the racks
Before loading the rack, remove all food residue from the
crockery, leave saucepans and frying pans with burnt-on
residue to soak in water only and empty all remaining liquid
from cups and glasses. After loading the appliance, check
that the sprayer arms can rotate freely.
If the rack is equipped with the click
clack handles* (see figure), pull
them upwards or downwards to
adjust the height.
EN
Lower rack
Arrange the more difficult items to wash using the Loading
examples as a guide and use the collapsible supports* where
needed.
Loading examples for the upper rack
•
•
•
Serving dishes and lids: place these at the sides of the
rack.
Saucepans and salad bowls: always turn these upside
down.
Very deep dishes: position these at an angle.
In order to guarantee the best washing and drying
performance, the surface of the lower rack is more uneven
than that of the upper rack.
Cutlery basket
The type of cutlery basket may vary according to the
Loading examples for the lower rack
dishwasher model.
Knives and other utensils with sharp edges must be
placed in the cutlery basket with the points facing downwards,
or they must be positioned horizontally in the tip-up
compartments on the upper rack.
Just you Tip-up compartments**
These special tip-up
compartments can be used to
arrange mugs and cups.
Spoons, forks and knives
should be placed in the slots
provided. Stemmed glasses
can be hooked on by threading
the stems into the slits.
To divide the central basket* into two separate pieces: pull out
the handle. The two detachable side compartments* may be
hooked onto the upper or lower rack.
The two grids* may be positioned in the basket to separate
the cutlery: place the pieces of cutlery into the appropriate
compartments with the handles at the bottom.
Items that should not be washed in the dishwasher
•
Upper rack
Wooden items, objects with wooden or horn handles or
glued-on parts.
Load this rack with delicate and lightweight crockery: glasses,
tea and coffee cups, saucers, small salad bowls, saucepans
and small saucepans that are not too soiled, using the Loading
examples as a guide.
•
•
•
•
Items made from aluminium, copper, brass, pewter or tin.
Items made from plastic that is not heat-resistant.
Antique or hand-painted porcelain.
Antique silver. Silver that is not antique may, however, be
washed in the dishwasher using a delicate wash cycle,
provided that it does not come into contact with other
metals.
•
•
•
Lightweight crockery: position these dishes so that they
will not be moved by the jets of water.
Mugs and cups: place these on the tip-up
compartments**.
Long sharp knives and serving utensils: place these on
the tip-up compartments**.
When buying crockery and cutlery we recommend that
you check whether it can be washed using the dishwasher.
Adjusting the height of the upper rack
In order to make it easier to arrange the crockery, the upper
Washing the handles*
To wash the upper and lower rack handles: remove the two
fastening plugs, lift out the handles and rinse them under
running water, then fasten them to the rack using the same
plugs.
rack may be moved to a higher or
lower level.
1
Open the left and right guide rail
stops and pull out the rack; position
it higher or lower as required, slide it
along the guide rails until the front
wheels are in place and close the
stops (see figure).
2
4
3
* Only available in selected models.
** The number and position may vary.
6
Start-up and use
compartment A: Washing
detergent
compartment B: Pre-wash
detergent
1. Open cover C by pressing
button D.
2. Pour in the detergent after
consulting the Wash cycle table:
• for powder detergent use
compartments A and B
• for tablets, use compartment A
and the bottom of the appliance,
Starting the dishwasher
D
EN
A
B
1. Turn the water tap on.
2. Press the ON/OFF button: the display will light up.
3. Measure out the detergent (see below).
4. Load the racks (see Loading the racks) and shut the door.
5. Select the programme by turning the WASH CYCLE
SELECT knob in a clockwise direction: align the notch on the
knob with the number or symbol representing the desired
wash cycle.
6. Select the wash options (see below).
C
7. Start the cycle by pressing the START/RESET button: the
machine will emit a confirmation beep. The WASH CYCLE
PHASE indicator lights display the status of the cycle: Pre-
wash, Wash, Rinse, or Drying.
i.e. when the cycle requires 1 tablet, place it in compartment A
and close the cover; when it requires 2, place the second
tablet at the bottom of the appliance.
8. At the end of the cycle three short beeps will sound and
END will appear on the display. Switch off the appliance by
pressing the ON/OFF button, shut off the water tap and
unplug the appliance from the electricity socket.
9. Open the door and wait for a few minutes before removing
the crockery, in order to avoid burns. Unload the racks,
beginning with the lower level.
3. Remove detergent residues from the edges of the
compartment and close the cover until it clicks.
Washing options
Delayed start
It is possible to delay the start time of the cycle for a period of
time between 1 and 24 hours.
Demo*
If dON appears on the display, this means that the appliance
is in demonstration mode. To deactivate it, press the START/
RESET and ON/OFF buttons simultaneously: dOF should
appear on the display.
1. Press the DELAYED START button: every time the button is
pressed, the time selected appears on the display and the
delayed start indicator light illuminates.
2. Select the wash cycle and press the START/RESET button:
after the beep sounds, the timer begins counting down.
3.Once this time is up, the indicator light switches off and the
wash cycle begins.
Modifying a wash cycle in progress
If a mistake was made during the wash cycle selection
process it is possible to change the cycle, provided that it has
only just begun: press and hold the START/RESET button for 4
seconds. After one long beep and three short beeps, the
WASH CYCLE PHASE indicator light will switch off. Select the
new cycle and switch the machine back on by pressing the
START/RESET button.
To adjust the delay time and select a lower period of time,
press the DELAYED START button. To cancel it, press the
button repeatedly until the wash cycle begins and the WASH
CYCLE PHASE indicator light corresponding to the start of the
cycle in progress illuminates.
Half load using the upper rack*
Adding extra crockery
If there are not many dishes to be washed, a half load cycle
may be used in order to save water, electricity and detergent.
Before selecting the wash cycle press the HALF LOAD button
repeatedly: the indicator light will illuminate and the wash cycle
will take place only in the upper rack.
Press the ON/OFF button and open the door, taking care to
avoid the escaping steam, and place the crockery inside the
dishwasher. Press the ON/OFF button again: the cycle starts
from the point at which it was interrupted.
Remember to load the upper rack only, and to reduce the
amount of detergent accordingly.
Accidental interruptions
If the door is opened during the wash cycle, or if there is a
power cut, the cycle stops. It starts again from the point at
which it was interrupted once the door has been shut or the
electricity supply is restored.
It is better to use powder detergent in this case.
Extra drying*
To make sure that the crockery is completely dry at the end of
the cycle, press the EXTRA DRYING button before selecting
the wash cycle. A prolonged beep will sound to indicate that
this option has been selected and a short beep will sound to
indicate when it has been deselected.
Loading the detergent
A successful wash also depends on the correct amount of
detergent being used, as recommended by the manufacturer.
Exceeding the recommended amount does not result in a
more effective wash and pollutes the environment.
If the Extra drying option is selected, the wash cycles will
last longer.
To obtain the best results from each washing and drying
cycle, powder detergent, rinse aid liquid and salt should be
used.
7
Washcycles
Wash cycle table
EN
INDESIT dishwashers are equipped with an automatic filter cleaning system so that they do not become clogged with food
residues. This function may extend the duration of the wash cycles. If there is a high level of dirt contained in the filters, the
dishwasher will stop operating (see Troubleshooting - Blocked filter alarm).
If the crockery is only lightly soiled or if it has been rinsed with water before being placed in the dishwasher, reduce the
amount of detergent used accordingly.
The number and type of wash cycles varies according to the model of dishwasher.
Wash cycle
Detergent
(A) = compartment A
(B) = compartment B
duration
(tolerance
10%)
Wash cycle selection
instructions
Wash cycle
Pre-wash
Drying
Powder
Liquid
Tablets
Hrs. Min.
1 (A)
1 (bottom
of the
Extremely soiled dishes
and pans (not to be
used for delicate items).
30 g (A)
5 g (B)
30 ml (A)
5 ml (B)
•
•
•
2.00’
1:28’
1) Intensive
2) Normal
appliance)
Normally soiled pans
and dishes. Standard
daily wash cycle.
30 g (A)
30 ml (A)
1 (A)
1 (A)
Environmentally-friendly
wash cycle with low
energy consumption
levels, suitable for pans
and dishes.
Economic and fast
wash cycle to be used
for lightly soiled dishes.
(Run cycle immediately
after use.)
25 g (A)
5 g (B)
25 ml (A)
5 ml (B)
•
•
2:25’
0:24’
0:12'
3) Eco
25 g (A)
25 ml (A)
4) Rapid
Preliminary wash cycle
for dishes while the load
is awaiting completion
with the dishes from the
next meal.
5) Soak
Special cycle to be used
for more delicate items
which are sensitive to
high temperatures. Run
cycle immediately after
use.
Economic and fast cycle
for a fairly small daily
load of dishes. This may
only be done on the
upper rack.
25 g (A)
25 g (A)
25 g (A)
1 (A)
•
1:38’
6) Crystal
25 ml (A)
0:48'
7) Just you
Note
To make it easier to measure out the detergent, it is worth remembering that:
1 tablespoon = 15 grams of powder = approximately 15 ml of liquid
1 teaspoon = 5 grams of powder = approximately 5 ml of liquid
8
Rinse aid and refined salt
Only use products that have been specifically designed
for dishwashers.
Do not use table salt or industrial salt.
1. Remove the lower rack and
unscrew the cap of the dispenser (in
an anti-clockwise direction).
EN
2. For the first wash cycle only: fill the
dispenser up to the edges with water.
3. Position the funnel provided
correctly (see figure) and fill the salt
dispenser up to the edges
If using a multi-functional product, it is not necessary to add
rinse aid; however, we recommend that you add salt,
especially if you live in an area where the water is hard or very
hard. If you do not add salt or rinse aid, the LOW SALT* and
LOW RINSE AID* indicator lights will flash continuously.
(approximately 2 kg); it is normal for
a little water to leak out.
Loading the rinse aid
4. Remove the funnel, wipe away any salt residue from the
thread and screw the cap on tightly, so that detergent does
not leak into the dispenser during the wash cycle (this could
damage the water softening system beyond repair).
Rinse aid makes it easier for the crockery to dry, as water runs
off surfaces more readily and therefore does not leave streaks
or marks.
The rinse aid dispenser should be filled:
When salt has been added, run a wash cycle
immediately, without crockery, in order to remove any salt
solution that has leaked out and to avoid corrosion.
•
whenever the indicator light (H) signals that it is empty.
Illuminated light: add rinse aid; unlit light: there is no
shortage of rinse aid in the dispenser.
when the LOW RINSE AID* indicator light on the panel
flashes;
•
Adjusting the amount of salt*
It is possible to adjust the amount of salt used according to the
hardness of the water in your area (this information is available
from your local water board).
1. Open the dispenser by
turning the lid (G) in an
H
anticlockwise direction.
2. Pour in the rinse aid, making
sure it does not overflow from
the dispenser. If this happens,
1. Unscrew the dispenser cap.
2. Turn the arrow on the neck of the
dispenser (see figure) towards the + or -
symbols, using the table below as a guide.
F
clean the spill immediately with a
sponge.
G
3. Screw the lid back on.
NEVER pour the rinse aid
directly into the appliance tub.
Adjusting the amount of rinse aid
If you are not completely satisfied with the drying results, you
may adjust the quantity of rinse aid used. Use a screwdriver
to turn the dosage adjuster to one of the 6 pre-set positions
(the default position is set to 4):
•
if there are streaks on the crockery, set the adjuster to a
lower number (1-3).
The default setting of the water softening system is +.
- If using multi-functional tablets, fill the salt dispenser and set
the adjuster to -; if the hardness of the water is greater than
60°fH, set it to +.
•
if drops of water remain on the crockery or there are
limescale marks present after the cycle has finished, set the
adjuster to a higher number (4-6).
If you are using multi-functional tablets and you wish to
further improve the drying performance of the appliance, fill
the dispenser and set the dosage adjuster to 2.
Loading the refined salt
In order to obtain the best possible results from a wash cycle,
make sure that the dispenser is never empty. Refined salt
removes limescale from the water, thus avoiding the formation
of deposits on crockery. The salt dispenser is located in the
lower part of the dishwasher (see Description) and should be
filled:
•
when the green float* cannot be seen by simply looking at
the cap of the salt dispenser;
•
•
when the LOW SALT* indicator light on the panel flashes;
if your machine is not equipped with an indicator light or a
green float:
approximately every 30 wash cycles;
* Only available in selected models.
9
Care and maintenance
Shutting off the water and electricity
supplies
Cleaning the filters
EN
The filters remove food residue from the water used
in the wash cycle: to obtain the best results from
each wash, they should be cleaned.
•
Turn off the water tap after every wash cycle to
avoid leaks.
•
Remove the plug from the socket when cleaning
the machine and when carrying out maintenance
work.
Clean the filters regularly.
After cleaning check that the filter assembly has
been replaced correctly.
Cleaning the dishwasher
The dishwasher should not be used without filters
or when the filter is loose.
•
The external surfaces of the machine and the
control panel may be cleaned using a non-
abrasive cloth which has been dampened with
water. Do not use solvents or abrasive products.
1. Remove the filters by pulling the handle upwards.
2. Clean the filters:
• after every wash
cycle, remove the
•
Any marks on the appliance interior may be
removed using a cloth dampened with water and
a little vinegar.
largest pieces of
residue from
C
1
semicircular plate A
and glass B (these
2
Preventing unpleasant odours
may be removed by
A
pulling the handle) by
B
•
Always keep the door of the appliance ajar in
order to avoid moisture from forming and being
trapped inside the machine.
rinsing them under
running water.
• The entire filter
•
Clean the seals around the door and detergent
dispensers regularly using a damp sponge. This
will avoid food becoming trapped in the seals,
which is the main cause of the formation of
unpleasant odours.
assembly should be
C
cleaned thoroughly
once a month: this
includes the
semicircular plate A,
the glass B and the
cylinder C (this may be
removed by turning it in
an anti-clockwise
B
A
Cleaning the sprayer arms
Food residue may
direction). Use a small
become encrusted onto
the sprayer arms and
block the holes used to
spray the water. It is
therefore recommended
that the arms are
non-metallic brush to clean these parts.
3. Reconstruct the filter assembly and replace it in
the correct position, following movements 1 and 2 as
shown in the figure, until it clicks into place.
checked from time to
time and cleaned with a
small non-metallic
Leaving the machine unused for
extended periods
brush.
•
•
Run a wash cycle when the dishwasher is empty.
Unplug the appliance and disconnect the water
supply.
•
Leave the door of the appliance ajar.
10
Precautions and advice
The appliance was designed and manufactured
in compliance with current international safety
standards. The following information has been
provided for safety reasons and should therefore be
read carefully.
Consumers should contact their local authority or
retailer for information concerning the correct
disposal of their old appliance.
EN
Saving energy and respecting the
environment
General safety
•
•
•
The appliance was designed for domestic use
inside the home and is not intended for
commercial or industrial use.
The appliance must be used by adults only, to
wash domestic crockery according to the
instructions in this manual.
The appliance must not be installed outdoors,
even in covered areas. It is extremely dangerous
to leave the machine exposed to rain and storms.
Do not touch the appliance when barefoot.
When unplugging the appliance always pull the
plug from the mains socket, do not pull on the
cable.
The water supply tap must be shut off and the
plug should be removed from the electrical
socket before cleaning the appliance or carrying
out any maintenance work.
If the appliance breaks down, do not under any
circumstances touch the internal parts in an
attempt to carry out the repair work yourself.
Never touch the heating element.
Do not lean or sit on the open door of the
appliance: this may cause the appliance to
overturn.
The door should not be left open as it may create
a dangerous obstacle.
Keep detergent and rinse aid out of reach of
children.
Saving water and energy
•
•
Only start a wash cycle when the dishwasher is
full. While waiting for the dishwasher to be filled,
prevent unpleasant odours with the Soak cycle
(see Wash Cycles).
Select a wash cycle that is suited to the type of
crockery and to the soil level of the crockery
using the Wash cycle table:
•
•
- for dishes with a normal soil level, use the Eco
wash cycle, which guarantees low energy and
water consumption levels.
- if the load is smaller than usual activate the Half
load option (see Start-up and use).
•
•
•
If your electricity supply contract gives details of
electricity saving time bands, run wash cycles
during the periods when a lower tariff is applied.
The Delayed start* button (see Start-up and use)
helps you organise the wash cycles accordingly.
•
•
Phosphate-free and chlorine-free detergents
containing enzymes
•
•
We strongly recommend that you use detergents
that do not contain phosphates or chlorine, as
these products are harmful to the environment.
Enzymes provide a particularly effective action at
temperatures around 50°C, and as a result
detergents containing enzymes can be used in
conjunction with low-temperature wash cycles in
order to achieve the same results as a normal
65°C wash cycle.
•
•
•
The packaging material should not be used as a
toy: it can become a choking or suffocation
hazard.
•
To avoid wasting detergent, use the product in
appropriate quantities based on the
Disposal of old electrical appliances
The European Directive 2002/96/EC on Waste
Electrical and Electronic Equipment (WEEE),
requires that old household electrical appliances
must not be disposed of in the normal unsorted
municipal waste stream. Old appliances must be
collected separately in order to optimise the
recovery and recycling of the materials they contain
and reduce the impact on human health and the
environment. The crossed out "wheeled bin" symbol
on the product reminds you of your obligation, that
when you dispose of the appliance it must be
separately collected.
manufacturer’s recommendations, the hardness
of the water and the soil level and quantity of the
crockery. Even if they are biodegradable,
detergents contain substances that may alter the
balance of nature.
* Only available in selected models.
11
195060375.00
Troubleshooting
10/2006- Xerox Business Services
Whenever the appliance fails to work, check for a solution from the following list before calling for Technical
Assistance Centre.
EN
Some problems are indicated by specific codes that flash on the display: make a note of any codes displayed
before calling Assistance.
Malfunction:
The dishwasher does not start.
Possible causes / Solutions:
• The plug has not been inserted into the electrical socket
properly, or there is no power in the house.
• The dishwasher door has not been shut properly.
• A delayed start has been programmed (see Start-up and use).
No water enters the dishwasher. • There is no water in the mains supply.
• The water inlet hose is bent (see Installation).
• The dishwasher cycle has not yet finished.
• The water outlet hose is bent (see Installation).
• The drain duct is blocked.
No water drains out from the
dishwasher.
• The filter is clogged up with food residues.
The dishwasher makes
excessive noise.
• The dishes are rattling against each other or against the
sprayer arms.
The dishes and glasses are
covered in a white film or
limescale deposits.
• The level of the refined salt is low or the dosage setting is not
suited to the hardness of the water (see Rinse aid and salt).
• The lid on the salt dispenser is not closed properly.
• The rinse aid has been used up or the dosage is too low.
• The crockery is made from non-stick material.
The dishes and glasses are
streaked or have a bluish
tinge.
• The rinse aid dosage is too high.
• The rinse aid has been used up or the dosage is too low (see
Rinse aid and salt).
The crockery has not been dried
properly.
• The rinse aid dispenser setting is not high enough.
• A wash cycle without a drying programme has been selected.
• The racks are overloaded (see Loading the racks).
• The crockery has not been arranged well.
The dishes are not clean.
• The sprayer arms cannot move freely.
• The wash cycle is too gentle (see Wash cycles).
• The detergent has not been measured out correctly or it is not
suited to the type of wash cycle (see Start-up and use).
• The filter is dirty or blocked (see Care and maintenance).
• The refined salt level is low (see Rinse aid and salt).
• Turn on the tap and the appliance will start after a few
minutes.
Shut off tap alarm.
(you will hear several short beeps)
(the code AO6 flashes on the
display).
• The appliance lock has been activated because nothing was
done when the beeps sounded. Switch off the machine using
the ON/OFF button, turn on the tap and switch the machine
back on after 20 seconds by pressing the same button. Re-
programme the machine and restart the wash cycle.
• Switch off the machine by pressing the ON/OFF button and
clean the filters (see Maintenance), then switch the
Blocked filter alarm
(the code AO5 flashes on the
display).
dishwasher back on by pressing the same button. Re-
programme the machine and restart the wash cycle.
• Switch off the appliance by pressing the ON/OFF button and
switch it back on after a minute. If the alarm continues, turn
off the water tap to reduce the risk of flooding, remove the
plug from the electrical socket and call Assistance.
Water loading solenoid valve
malfunction alarm
(the code AO2 flashes on the
display).
12
|